The amount to copy for the first block is the minimum of the size of
the AAD region or the remaining space in the first block.
Reported by: cryptocheck -z
MFC after: 2 weeks
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D25140
- Clear the current thread's TLS pointer on exec. Previously the TLS
pointer (and register) remain unchanged.
- Explicitly clear the TLS pointer when new threads are created.
- Make md_tls_tcb_offset per-process instead of per-thread.
The layout of the TLS and TCB are identical for all threads in a
process, it is only the TLS pointer values themselves that vary by
thread. This also makes setting md_tls_tcb_offset in
cpu_set_user_tls() redundant with the setting in exec_setregs(), so
only set it in exec_setregs().
Submitted by: Alfredo Mazzinghi (1)
Sponsored by: DARPA
Differential Revision: https://reviews.freebsd.org/D24957
The Intel Instruction Set Reference says this about the XSAVE instruction:
Use of a destination operand not aligned to 64-byte boundary
(in either 64-bit or 32-bit modes) results in a general-protection
(#GP) exception.
This alignment happens naturally when all malloc buckets are powers
of two. However, this change is necessary on some systems when
certain non-power-of-two (and non-multiple of 64) malloc buckets
are defined.
Reviewed by: cem; kib; earlier version by jhb
MFC after: 2 weeks
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D25098
In particular, uma_zcreate creates sysctl oids, which locks an sx lock,
which uses IPIs under contention. IPIs tend not to work very well
when interrupts are disabled. Who knew, right?
Reviewed by: cem kib
MFC after: 2 weeks
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D25098
always want to do a window update, even when no data can be sent. Now in
cases where you are not pacing thats probably ok, you just send an extra
window update or two. However with bbr (and rack if its paced) every time
the pacer goes off its going to send a "window update".
Also in testing bbr I have found that if we are not responding to
data right away we end up staying in startup but incorrectly holding
a pacing gain of 192 (a loss). This is because the idle window code
does not restict itself to only work with PROBE_BW. In all other
states you dont want it doing a PROBE_BW state change.
Sponsored by: Netflix Inc.
Differential Revision: https://reviews.freebsd.org/D25247
Given that 64c/128t CPUs are currently available, and that many
devices (nvme, many NICs) desire to map 1 MSI-X vector per core,
or even 1 per-thread, it is becoming far easier to see MSI-X interrupt
setup fail due to msi vector exhaustion, and devices fail to attach at
boot on large system.
This bump costs 12KB on amd64 (and 6KB on i386), which seems
worth the trade off for a better out of the box experience on
high end hardware.
Reviewed by: jhb
MFC after: 21 days
Sponsored by: Netflix
libc cannot assume that aligned_alloc and free come from jemalloc, or that
any application providing its own malloc and free is actually providing
aligned_alloc.
Switch back to malloc and just make sure we're passing a properly aligned
stack into rfork_thread, as an application perhaps can't reasonably replace
just malloc or just free without headaches.
This unbreaks ksh93 after r361996, which provides malloc/free but no
aligned_alloc.
Reported by: freqlabs
Diagnosed by: Andrew Gierth <andrew_tao173.riddles.org.uk>
X-MFC-With: r361996
RB_LEFT or RB_RIGHT, so they aren't stripping off the color bit
encoded there. Strip off that bit for linuxkpi.
Reported by: dch
Reviewed by: markj
Differential Revision: https://reviews.freebsd.org/D25245
the debug messages. While here, clean up some variable naming.
Reviewed by: bcr (manpages), emaste
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D25230
This is useful for tracking hardware provided AMSDU frames to see
when we're (a) seeing them, and (b) seeing the split between
intermediary and final frames.
Tested:
* QCA9880 (athp) - AP mode
When doing A-MSDU offload handling the driver is required to mark
A-MSDUs from the same MPDU with the same sequence number.
It then tags them as AMSDU (if it's a decap'ed A-MSDU) and AMSDU_MORE
(saying there's more AMSDUs decapped in the same MSDU.)
This allows encryption and sequence number offload to work right.
In the A-MSDU path the sequence number check looks at the A-MSDU flags
in the frame to see whether it's part of the same seqno and will pass them
(ie, not increment rx_seq until the last A-MSDU is seen from the driver,
or a new seqno shows up.0
However, I did this work in the A-MSDU path but not the A-MSDU in A-MPDU path.
For the non A-MDSU offload case the A-MPDU receive reordering will do its
thing and then pass up the MPDU up for decap - which then will see it's
an A-MSDU and decap each sub-frame. But this isn't done for offloaded
A-MSDU frames.
This requires two parts:
* Don't bump the RX sequence number, same as above; and
* If frames go into the reordering buffer, they need to be added into the slot
as a set of frames rather than a single frame, so once a new seqno shows up
this slot can be marked as "full" and we can move on.
This patch does the first. The latter requires that I find and commit
work to change rxa_m from an mbuf to an mbufq and the nhandle A-MSDU
there. But, the first is enough to allow the normal case (ie, no or not
a lot of A-MPDU RX reordering) to work.
This allows the athp driver (QCA9880) throughput to go from VERY low
(like 5mbit TCP, 1/3-1/4 expected UDP throughput) to ~ 250mbit TCP
and > 300mbit UDP on a VHT/40 channel. TCP sucks because, well, it
shows up as MASSIVE packet loss when all but one frame in a decap'ed
A-MSDU stream is dropped. Le whoops.
Now, where'd I put that laptop with the patch for rxa_m mbufq that
I wrote like in 2017...
Tested:
* AR9380, STA/AP mode (a big no-op, no A-MSDU hardware decap);
* if_run (RT3593), STA DWDS mode (A-MPDU / A-MSDU receive, but again
no A-MSDU hardware decap);
* QCA9880, STA/AP mode (which is doing hardware A-MPDU/A-MSDU decap,
but no A-MPDU reordering in the firmware.)
r286700 added the "lacp_fast_timeout" option to `ifconfig', but we forgot to
include the new option in the string used to decode the option bits. Add
"LACP_FAST_TIMO" to LAGG_OPT_BITS.
Also, s/LAGG_OPT_LACP_TIMEOUT/LAGG_OPT_LACP_FAST_TIMO/g , to be clearer that
the flag indicates "Fast Timeout" mode.
Reported by: Greg Foster <gfoster at panasas dot com>
Reviewed by: jpaetzel
MFC after: 1 week
Sponsored by: Panasas
Differential Revision: https://reviews.freebsd.org/D25239
This function returns NULL if the ring identified by
queue id and direction is in netmap mode. Otherwise
return the corresponding kring.
Use this function to replace vtnet_netmap_queue_on().
MFC after: 1 week
In particular, invalidation of the preloaded modules text to allow
execution from it was broken after D25188/r362031.
Reviewed by: markj
Reported by: delphij, dhw
Sponsored by: The FreeBSD Foundation
MFC after: 13 days
This partially reverts r361053 since there have been reports
by users that this breaks some functionality for em(4)
devices; it seems at first glance that some sort of interface
restart is required for those cards.
This isn't a proper fix; this unbreaks those users until a proper
fix is found for their issues.
PR: 240818
Reported by: Marek Zarychta <zarychtam@plan-b.pwste.edu.pl>
MFC after: 3 days
Add EXAMPLES covering options I, J, L, n, P.
While here, fix warning (STYLE: no blank before trailing delimiter: Fl P,)
Bumping .Dd
Approved by: bcr@
Differential Revision: https://reviews.freebsd.org/D25214
With this change all ZVOL updates are initiated from the SPA sync
context instead of a mix of the sync and open contexts. The updates are
queued to be applied by a dedicated thread in the original order. This
should ensure that ZVOLs always accurately reflect the corresponding
datasets. ZFS ioctl operations wait on the mentioned thread to complete
its work. Thus, the illusion of the synchronous ZVOL update is
preserved. At the same time, the SPA sync thread never blocks on ZVOL
related operations avoiding problems like reported in bug 203864.
This change is based on earlier work in the same direction: D7179 and
D14669 by Anthoine Bourgeois. D7179 tried to perform ZVOL operations
in the open context and that opened races between them. D14669 uses a
design very similar to this change but with different implementation
details.
This change also heavily borrows from similar code in ZoL, but there are
many differences too. See:
- a0bd735adb
- https://github.com/zfsonlinux/zfs/issues/3681
- https://github.com/zfsonlinux/zfs/issues/2217
PR: 203864
MFC after: 5 weeks
Sponsored by: CyberSecure
Differential Revision: https://reviews.freebsd.org/D23478
Allow the TCP header to reside in the mbuf following the IP header.
Else such packets will get dropped.
Backtrace:
mlx5e_sq_xmit()
mlx5e_xmit()
ether_output_frame()
ether_output()
ip_output_send()
ip_output()
rip_output()
sosend_generic()
sosend()
kern_sendit()
sendit()
sys_sendto()
amd64_syscall()
fast_syscall_common()
MFC after: 1 week
Sponsored by: Mellanox Technologies
Typically the TCP/IP headers fit within the first mbuf and should not
trigger any of the error cases. Use unlikely() for these cases.
No functional change.
MFC after: 1 week
Sponsored by: Mellanox Technologies
When parsing the TCP/IP header in the fast path, make it clear by using
the const keyword, no fields are to be modified inside the transmitted
packet.
No functional change.
MFC after: 1 week
Sponsored by: Mellanox Technologies
