r357614 added CTLFLAG_NEEDGIANT to make it easier to find nodes that are
still not MPSAFE (or already are but aren’t properly marked).
Use it in preparation for a general review of all nodes.
This is non-functional change that adds annotations to SYSCTL_NODE and
SYSCTL_PROC nodes using one of the soon-to-be-required flags.
Mark all obvious cases as MPSAFE. All entries that haven't been marked
as MPSAFE before are by default marked as NEEDGIANT
Approved by: kib (mentor, blanket)
Commented by: kib, gallatin, melifaro
Differential Revision: https://reviews.freebsd.org/D23718
switch over to opt-in instead of opt-out for epoch.
Instead of IFF_NEEDSEPOCH, provide IFF_KNOWSEPOCH. If driver marks
itself with IFF_KNOWSEPOCH, then ether_input() would not enter epoch
when processing its packets.
Now this will create recursive entrance in epoch in >90% network
drivers, but will guarantee safeness of the transition.
Mark several tested drivers as IFF_KNOWSEPOCH.
Reviewed by: hselasky, jeff, bz, gallatin
Differential Revision: https://reviews.freebsd.org/D23674
The index should be computed as distance from arg[0] and not
the beginning of struct mlx5_ib_congestion .
While at it fix a use of zero length array to avoid depending
on undefined compiler behaviour.
MFC after: 1 week
Sponsored by: Mellanox Technologies
The upstream OpenSSL changes only set the cipher for GCM since the
authentication is redundant, and changes to OCF will soon remove the
GCM authentication algorithm constants entirely for the same reason.
In addition, ktls_create_session() already validates these fields and
wouldn't pass down an invalid auth_algorithm value to any drivers or
ktls backends.
Reviewed by: hselasky
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D23671
Make completion event path mostly lockless using EPOCH(9).
Implement a mechanism using EPOCH(9) which allows us to make
the callback path for completion events mostly lockless.
Simplify draining callback events using epoch_wait().
While at it make sure all receive completion callbacks are
covered by the network EPOCH(9), because this is required
when calling if_input() and ether_input() after r357012.
Sponsored by: Mellanox Technologies
ConnectX-6 DX.
Currently TLS v1.2 and v1.3 with AES 128/256 crypto over TCP/IP (v4
and v6) is supported.
A per PCI device UMA zone is used to manage the memory of the send
tags. To optimize performance some crypto contexts may be cached by
the UMA zone, until the UMA zone finishes the memory of the given send
tag.
An asynchronous task is used manage setup of the send tags towards the
firmware. Most importantly setting the AES 128/256 bit pre-shared keys
for the crypto context.
Updating the state of the AES crypto engine and encrypting data, is
all done in the fast path. Each send tag tracks the TCP sequence
number in order to detect non-contiguous blocks of data, which may
require a dump of prior unencrypted data, to restore the crypto state
prior to wire transmission.
Statistics counters have been added to count the amount of TLS data
transmitted in total, and the amount of TLS data which has been dumped
prior to transmission. When non-contiguous TCP sequence numbers are
detected, the software needs to dump the beginning of the current TLS
record up until the point of retransmission. All TLS counters utilize
the counter(9) API.
In order to enable hardware TLS offload the following sysctls must be set:
kern.ipc.mb_use_ext_pgs=1
kern.ipc.tls.ifnet.permitted=1
kern.ipc.tls.enable=1
Sponsored by: Mellanox Technologies
The hardware offload is primarily targeted for TLS v1.2 and v1.3,
using AES 128/256 bit pre-shared keys. This patch adds all the needed
hardware structures, capabilites and firmware commands.
Sponsored by: Mellanox Technologies
As noted by the commit message, callouts are now persistant
and should not be in the auto-zero section of the RQ's and SQ's.
This fixes an assert when using the TX completion event
factor feature with mlx5en(4).
Found by: gallatin@
MFC after: 3 days
Sponsored by: Mellanox Technologies
The PRM suggests random 0 - 10ms to prevent multiple waiters on the same
interval in order to avoid starvation.
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
Before attempting to initialize the command interface we must wait till
the fw_initializing bit is clear.
If we fail to meet this condition the hardware will drop our
configuration, specifically the descriptors page address. This scenario
can happen when the firmware is still executing an FLR flow and did not
finish yet so the driver needs to wait for that to finish.
Linux commits:
6c780a0267b8
b8a92577f4be.
MFC after: 3 days
Sponsored by: Mellanox Technologies
in mlx5en(4) after r348254.
The unlimited send tags are shared amount multiple connections and are
not allocated per send tag allocation request. Only increment the refcount.
MFC after: 3 days
Sponsored by: Mellanox Technologies
It may happen during link down that the running state may be observed
non-zero in the transmit routine, right before the running state is
cleared. This may end up using a destroyed mutex.
Make all channel mutexes and callouts persistant.
Preserve receive and send queue statistics during link toggle.
MFC after: 3 days
Sponsored by: Mellanox Technologies
in mlx5core. The EEPROM information is not only a property of the
mlx5en(4) driver.
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
The following sysctls are added:
dev.mce.N.conf.qos.cable_length
dev.mce.N.conf.qos.buffers_size
dev.mce.N.conf.qos.buffers_prio
Submitted by: kib@
MFC after: 3 days
Sponsored by: Mellanox Technologies
All prints in mlx5core should use on of the macros:
mlx5_core_err/dbg/warn
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
In case of health counter fails to increment it indicates a bad device health.
In case when the syndrome indicated by firmware is 0x0, this indicates that
firmware is unable to respond to initialization segment reads.
Add proper print in this case.
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
MPFS is a logical switch in the Mellanox device which forward packets
based on a hardware driven L2 address table, to one or more physical-
or virtual- functions. The physical- or virtual- function is required
to tell the MPFS by using the MPFS firmware commands, which unicast
MAC addresses it is requesting from the physical port's traffic.
Broadcast and multicast traffic however, is copied to all listening
physical- and virtual- functions and does not need a rule in the MPFS
switching table.
Linux commit: eeb66cdb682678bfd1f02a4547e3649b38ffea7e
MFC after: 3 days
Sponsored by: Mellanox Technologies
Add the 512 bytes limit of RDMA READ and the size of remote address to the max
SGE calculation.
Submitted by: slavash@
Linux commit: 288c01b746aa
MFC after: 3 days
Sponsored by: Mellanox Technologies
an updated rack depend on having access to the new
ratelimit api in this commit.
Sponsored by: Netflix Inc.
Differential Revision: https://reviews.freebsd.org/D20953
- Perform ifp mismatch checks (to determine if a send tag is allocated
for a different ifp than the one the packet is being output on), in
ip_output() and ip6_output(). This avoids sending packets with send
tags to ifnet drivers that don't support send tags.
Since we are now checking for ifp mismatches before invoking
if_output, we can now try to allocate a new tag before invoking
if_output sending the original packet on the new tag if allocation
succeeds.
To avoid code duplication for the fragment and unfragmented cases,
add ip_output_send() and ip6_output_send() as wrappers around
if_output and nd6_output_ifp, respectively. All of the logic for
setting send tags and dealing with send tag-related errors is done
in these wrapper functions.
For pseudo interfaces that wrap other network interfaces (vlan and
lagg), wrapper send tags are now allocated so that ip*_output see
the wrapper ifp as the ifp in the send tag. The if_transmit
routines rewrite the send tags after performing an ifp mismatch
check. If an ifp mismatch is detected, the transmit routines fail
with EAGAIN.
- To provide clearer life cycle management of send tags, especially
in the presence of vlan and lagg wrapper tags, add a reference count
to send tags managed via m_snd_tag_ref() and m_snd_tag_rele().
Provide a helper function (m_snd_tag_init()) for use by drivers
supporting send tags. m_snd_tag_init() takes care of the if_ref
on the ifp meaning that code alloating send tags via if_snd_tag_alloc
no longer has to manage that manually. Similarly, m_snd_tag_rele
drops the refcount on the ifp after invoking if_snd_tag_free when
the last reference to a send tag is dropped.
This also closes use after free races if there are pending packets in
driver tx rings after the socket is closed (e.g. from tcpdrop).
In order for m_free to work reliably, add a new CSUM_SND_TAG flag in
csum_flags to indicate 'snd_tag' is set (rather than 'rcvif').
Drivers now also check this flag instead of checking snd_tag against
NULL. This avoids false positive matches when a forwarded packet
has a non-NULL rcvif that was treated as a send tag.
- cxgbe was relying on snd_tag_free being called when the inp was
detached so that it could kick the firmware to flush any pending
work on the flow. This is because the driver doesn't require ACK
messages from the firmware for every request, but instead does a
kind of manual interrupt coalescing by only setting a flag to
request a completion on a subset of requests. If all of the
in-flight requests don't have the flag when the tag is detached from
the inp, the flow might never return the credits. The current
snd_tag_free command issues a flush command to force the credits to
return. However, the credit return is what also frees the mbufs,
and since those mbufs now hold references on the tag, this meant
that snd_tag_free would never be called.
To fix, explicitly drop the mbuf's reference on the snd tag when the
mbuf is queued in the firmware work queue. This means that once the
inp's reference on the tag goes away and all in-flight mbufs have
been queued to the firmware, tag's refcount will drop to zero and
snd_tag_free will kick in and send the flush request. Note that we
need to avoid doing this in the middle of ethofld_tx(), so the
driver grabs a temporary reference on the tag around that loop to
defer the free to the end of the function in case it sends the last
mbuf to the queue after the inp has dropped its reference on the
tag.
- mlx5 preallocates send tags and was using the ifp pointer even when
the send tag wasn't in use. Explicitly use the ifp from other data
structures instead.
- Sprinkle some assertions in various places to assert that received
packets don't have a send tag, and that other places that overwrite
rcvif (e.g. 802.11 transmit) don't clobber a send tag pointer.
Reviewed by: gallatin, hselasky, rgrimes, ae
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D20117
This was enumerated with exhaustive search for sys/eventhandler.h includes,
cross-referenced against EVENTHANDLER_* usage with the comm(1) utility. Manual
checking was performed to avoid redundant includes in some drivers where a
common os_bsd.h (for example) included sys/eventhandler.h indirectly, but it is
possible some of these are redundant with driver-specific headers in ways I
didn't notice.
(These CUs did not show up as missing eventhandler.h in tinderbox.)
X-MFC-With: r347984
There is no reason to re-create the command workqueue during healthcare.
This also fixes an issue where a previous work struct may refer to a
destroyed workqueue.
MFC after: 3 days
Sponsored by: Mellanox Technologies
Present code uses lock-less accesses to the dump data to prevent top
level ioctls from blocking bottom-level call to dump. Unfortunately, this
depends on the type stability of the dump data structure, which makes it
non-functional during driver teardown.
Switch to the mutex locking scheme where top levels use the mutex in the
bound regions, while copyouts and drain for completion utilize condvars.
The mutex lifetime is guaranteed to be strictly larger than the time
interval where driver can initiate dump, and most of the control fields
of the old struct mlx5_dump_data are directly embedded into struct
mlx5_core_dev.
Submitted by: kib@
MFC after: 3 days
Sponsored by: Mellanox Technologies
Avoid race for command completion when triggering a command completions event.
Serialize operation by queueing all commands on the same work queue.
This can happen when healthcare triggers.
MFC after: 3 days
Sponsored by: Mellanox Technologies
The command timeout is terribly long, whole two hours. Make it 60s so if
things do go wrong, the user gets feedback in relatively short time, so
they can take corrective actions and/or investigate using tools and such.
Linux commit:
6b6c07bdcdc97ccac2596063bfc32a5faddfe884
MFC after: 3 days
Sponsored by: Mellanox Technologies
Function 'mlx5e_alloc_rx_wqe' can never be inlined because it uses alloca
(override using the always_inline attribute)
MFC after: 3 days
Sponsored by: Mellanox Technologies
Allow more macro arguments and split the variable type and name into
separate arguments. This allows simple and powerful copy and extraction
of values from IFC based structures into SYSCTLs with the use of a single
macro.
MFC after: 3 days
Sponsored by: Mellanox Technologies
Implement a watchdog as part of the healtcare subsystem which
reads the PCI power status during startup and upon the PCI
power status change event and store it into the core device
structure. This value is then exported to user-space via a
read-only SYSCTL. A dmesg print has been added to inform
the admin about the PCI power status.
MFC after: 3 days
Sponsored by: Mellanox Technologies
CM layer calls ib_modify_port() regardless of the link layer.
For the Ethernet ports, qkey violation and Port capabilities
are meaningless. Therefore, always return success for ib_modify_port
calls on the Ethernet ports.
Linux Commit:
ec2558796d25e6024071b6bcb8e11392538d57bf
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
mlx5en(4).
IFM_10G_LR and IFM_40G_ER4 media should be added only if the device
has the needed capability bit set for it.
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
If generation is cleared due to hardware clock failure, check for it before
the divisor is used. Actually clear generation when failure occurs.
While there, stop doing the calculations inside the generation loop. Since
all members of mlx5e_clbr_point are used for calculations, get the
local copy of the structure and use it after generation stabilized.
Submitted by: kib@
MFC after: 3 days
Sponsored by: Mellanox Technologies
This fixes counting issues when the firmware resets the counter during
allocation of the counter set where the counter belongs.
MFC after: 3 days
Sponsored by: Mellanox Technologies
The physical- and virtual- port counters might not reflect the amount
of data received after address filtering. Use the software counters
instead for rx_packets and rx_bytes to know exactly how much data
was received.
MFC after: 3 days
Sponsored by: Mellanox Technologies
mlx5_pci_disable_device is calling pci_disable_device which disables
bus master. No need to explicitly call pci_clear_master.
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
Add mlx5 implementation for the ones defined by the mlxfw
shared module to be used while flashing the device firmware.
The callbacks do their job through the MCQI, MCC and MCDA registers.
Linux commit:
62bd22cf326dc4ac5be673c11cef4602dc1f5e47
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
The current mapping of driver counters to netstat counters is wrong.
For example, a single jabber packet, will cause the Ierrs counter to
count three times.
The work for mapping the hardware and software counters to their right
place in netstat counters were already done in Linux, take that as is
to the FreeBSD driver.
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
To be used by the mlx5 callbacks exposed to the mlxfw module.
Linux commit:
d2ad488b0073bd1a2c3f5d2ea50a7eb632103e5d
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
Enhance MCAM to allow the driver to query which access regs are
supported. For now, expose the regs needed for FW flashing.
Linux commit:
0ab87743cc8c5bcd482daf71961ed5fc45349e01
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
MCC (Management Component Control) allows to control a firmware
component update.
MCDA (Management Component Data Access) allows to read and write
a firmware component.
MCQI (Management Component Query Information) allows to query
information about firmware components.
Linux commit:
4717628938423fcba0aa8fa889e9fed4eb6a655f
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
On load_one, we now cache our capabilities registers internally, similar
to QUERY_HCA_CAP. Capabilities can later be queried using macros
introduced in this patch.
Linux commit:
71862561f3a62015a11de16d1c306481e8415c08
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
Introduced registers will expose capabilities of new registers and
features related to port/management.
Driver will query MCAM and PCAM in order to avoid failing on old
firmwares with lack of support.
Linux commit:
c835ad64683bd3e2d1b31ed2cb1ff4366932edb1
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
PCAM: Ports capabilities mask register.
MCAM: Management capabilities mask register.
PCAM and MCAM registers will provide information regarding firmware
support for different features, in order to avoid cases where new driver
combined with old firmware results in syndromes (for ex. PCIe counters
before this patchset).
Linux commit:
cfdcbceaeffc669b70d904d80a2df9c86c232566
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
Today mlx5 devices support two teardown modes:
1- Regular teardown
2- Force teardown
This change introduces the enhanced version of the "Force teardown" that
allows SW to perform teardown in a faster way without the need to reclaim
all the pages.
Fast teardown provides the following advantages:
1- Fix a FW race condition that could cause command timeout
2- Avoid moving to polling mode
3- Close the vport to prevent PCI ACK to be sent without been
scattered to memory
Linux commit:
fcd29ad17c6ff885dfae58f557e9323941e63ba2
MFC after: 3 days
Sponsored by: Mellanox Technologies
Else the SQs won't be properly released when closing rate-limited connections
leading to wrong state transitions on the SQ.
MFC after: 3 days
Sponsored by: Mellanox Technologies
When using CQE zipping, one can choose between RX hash and Checksum.
This will indicate the parameter on which a zipping session should be
stopped.
While porting the Linux code, Checksum was chosen. However, the value
of Checksum is not being used anywhere.
For the FreeBSD driver, we prefer to use the RX hash format which will
guarantee the RX hash value for all the mini CQEs.
While at it, make sure to initialize the Checksum value in the
decompressed CQE.
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
After doing performance measurements, it seems like CQE zipping doesn't
have any significant benefit.
Moreover, we know that this feature is disabled by default on other
operating systems (Linux for example).
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
Split the function into the mlx5e_update_stats_locked() core and make
mlx5e_update_stats_work() call the _locked helper, similar to many other
places in the kernel. This improves the code structure, making the
locking clean.
Submitted by: kib@
MFC after: 3 days
Sponsored by: Mellanox Technologies
Instead of waiting for all jobs to be cancelled, simply close the completion
queue to prevent more completion events and let mlx5e_destroy_rq() cleanup
the remaining mbufs.
MFC after: 3 days
Sponsored by: Mellanox Technologies
The number of priorities is always 8, while the number of traffic classes
supported can vary. While at it convert the sysctl node into an array.
MFC after: 3 days
Sponsored by: Mellanox Technologies
Instead of reading Ethernet RFC 2819 pXtoYoctets counters from
hardware which counts RX octets, count tx_stat_pXtoYoctets from
Ethernet extended counters which counts TX octets.
TX jumbo counters should be accumulated only after the PPCNT
counters were fetched from hardware with their latest value.
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
Avoid an infinite software firmware reset loop that may be caused by a
hardware bug by limiting the maximum number of resets.
The counter between resets is reset by request for reset, and not by a
successful reset.
The interval between two resets can be configured via sysctl:
hw.mlx5.sw_reset_timeout
which is global to all mlx5 devices in the system.
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
Make sure the interrupt handlers don't race with the fast unload one
code in the shutdown handler.
MFC after: 3 days
Sponsored by: Mellanox Technologies
Temperature warning event is sent by FW to indicate high temperature
as detected by one of the sensors on the board.
Add handling of this event by writing the numbers of the alert sensors
to the kernel log.
Linux commit:
1865ea9adbfaf341c5cd5d8f7d384f19948b2fe9
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
While at it remove unused interface state bits. This also fixes and issue
during shutdown:
There is an issue where the firmware fails during mlx5_load_one,
the health_care timer detects the issue and schedules a health_care call.
Then the mlx5_load_one detects the issue, cleans up and quits. Then
the health_care starts and calls mlx5_unload_one to clean up the resources
that no longer exist and causes kernel panic.
The root cause is that the bit MLX5_INTERFACE_STATE_DOWN is not set
after mlx5_load_one fails. The solution is removing the bit
MLX5_INTERFACE_STATE_DOWN and quit mlx5_unload_one if the
bit MLX5_INTERFACE_STATE_UP is not set. The bit MLX5_INTERFACE_STATE_DOWN
is redundant and we can use MLX5_INTERFACE_STATE_UP instead.
Linux commit:
10a8d00707082955b177164d4b4e758ffcbd4017
b3cb5388499c5e219324bfe7da2e46cbad82bfcf
MFC after: 3 days
Sponsored by: Mellanox Technologies
Add support for DIM based on Linux,
with some minor adaptions specific to FreeBSD.
Linux commit
f97c3dc3c0e8d23a5c4357d182afeef4c67f5c33
MFC after: 3 days
Sponsored by: Mellanox Technologies
Drivers can now pass up numa domain information via the
mbuf numa domain field. This information is then used
by TCP syncache_socket() to associate that information
with the inpcb. The domain information is then fed back
into transmitted mbufs in ip{6}_output(). This mechanism
is nearly identical to what is done to track RSS hash values
in the inp_flowid.
Follow on changes will use this information for lacp egress
port selection, binding TCP pacers to the appropriate NUMA
domain, etc.
Reviewed by: markj, kib, slavash, bz, scottl, jtl, tuexen
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D20028
This commit adds new if_alloc_domain() and if_alloc_dev() methods to
allocate ifnets. When called with a domain on a NUMA machine,
ifalloc_domain() will record the NUMA domain in the ifnet, and it will
allocate the ifnet struct from memory which is local to that NUMA
node. Similarly, if_alloc_dev() is a wrapper for if_alloc_domain
which uses a driver supplied device_t to call ifalloc_domain() with
the appropriate domain.
Note that the new if_numa_domain field fits in an alignment pad in
struct ifnet, and so does not alter the size of the structure.
Reviewed by: glebius, kib, markj
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D19930
This allows efficient filtering at packet ingress on mlx5en.
Note that the packets are filtered (and potentially dropped) *before*
the driver has committed to (re)allocating an mbuf for the
packet. Dropped packets are treated essentially the same as an
error. Nothing is allocated, and the existing buffer is recycled. This
allows us to drop malicious packets at close to line rate with very
little CPU use.
Reviewed by: hselasky, slavash, kib
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D19063
The backpressure indication is implemented using an unlimited rate type of
mbuf send tag. When the upper layers typically the socket layer has obtained such
a tag, it can then query the destination driver queue for the current
amount of space available in the send queue.
A single mbuf send tag may be referenced multiple times and a refcount has been added
to the mlx5e_priv structure to track its usage. Because the send tag resides
in the mlx5e_channel structure, there is no need to wait for refcounts to reach
zero until the mlx4en(4) driver is detached. The channels structure is persistant
during the lifetime of the mlx5en(4) driver it belongs to and can so be accessed
without any need of synchronization.
The mlx5e_snd_tag structure was extended to contain a type field, because there are now
two different tag types which end up in the driver which need to be distinguished.
Submitted by: hselasky@
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
In order to enable HW LRO, both the "hw_lro" sysctl in the mlx5en(4) config
space must be set, and the ifconfig(8) LRO capability must be set. Any other
settings will disable HW LRO.
Submitted by: hselasky@
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
Add counter for all transmitted and received bytes. Currently only all
transmitted and received packets were counted. Fix description of RX LRO
counters while at it.
Submitted by: hselasky@
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
By allocating the worst case size channel structure array
at attach time we can eliminate various NULL checks in the
fast path. And also reduce the chance for use-after-free
issues in the transmit fast path.
This change is also a requirement for implementing
backpressure support.
Submitted by: hselasky@
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
Writing to the debug stats variable must be locked,
else serialization will be lost which might cause
various kernel panics due to creating and destroying
sysctls out of order.
Make sure the sysctl context is initialized after freeing
the sysctl nodes, else they can be freed twice.
Submitted by: hselasky@
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
Inspect the ethernet compliance code to figure out actual cable type by reading
the PDDR module info register.
Submitted by: hselasky@
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
This can happen when connections are short lived and leads to
a firmware error printout in dmesg, syndrome 0x51cfb0, because
the SQ is in the wrong state.
Submitted by: hselasky@
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
1) Don't exceed the drivers own hardcoded TX inline limit.
The blueflame register size can be much greater than the hardcoded limit
for inlining. Make sure we don't exceed the drivers own limit, because this
also means that the maximum number of TX fragments becomes invalid and
then memory size assumptions in the TX path no longer hold up.
2) Make sure the mlx5_query_min_inline() function returns an error code.
3) Header inlining is required when using TSO.
4) Catch failure to compute inline header size for TSO.
5) Add support for UDP when computing inline header size.
6) Fix for inlining issues with regards to DSCP.
Make sure we inline 4 bytes beyond the ethernet and/or
VLAN header to workaround a hardware bug extracting
the DSCP field from the IPv4/v6 header.
Submitted by: hselasky@
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
The hardware queues are deep enough currently and using the DRBR and associated
callbacks only leads to more task switching in the TX path. The is also a race
setting the queue_state which can lead to hung TX rings.
Submitted by: hselasky@
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
Add support for setting the bandwidth limit as a ratio rather than in bits per
second. The ratio must be an integer number between 1 and 100 inclusivly.
Implement the needed firmware commands and SYSCTLs through mlx5en(4).
Submitted by: hselasky@
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
Make sure the active width and speed is set in case the
translate_eth_proto_oper() function doesn't recognize the
current port operation mask.
Linux commit:
7672ed33c4c15dbe9d56880683baaba4227cf940
Submitted by: hselasky@
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
If the mlx5_ib_read_cong_stats() function was running when mlx5ib was unloaded,
because this function unconditionally restarts the timer, the timer can still
be pending after the delayed work has been cancelled. To fix this simply loop
on the delayed work cancel procedure as long as it returns non-zero.
Submitted by: hselasky@
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
Although "create_srq_user" does overwrite "in.pas" on some paths, it
also contains at least one feasible path which does not overwrite it.
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
"fw_rev_min(dev->mdev)" with type "unsigned short" (16 bits, unsigned) is
promoted in "fw_rev_min(dev->mdev) << 16" to type "int" (32 bits, signed), then
sign-extended to type "unsigned long" (64 bits, unsigned). If
"fw_rev_min(dev->mdev) << 16" is greater than 0x7FFFFFFF, the upper bits of the
result will all be 1.
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
Driver description should be set by core and not by the Ethernet driver.
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
A command is either polling or event driven and the mode cannot change
during execution of a command. Make sure the event handler only handle
commands which are not polled. This is done by checking the command mode
in the command handler before completing commands.
Submitted by: hselasky@
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
This counter will represent transmitted packets which has more than
1518 octets.
The NIC has multiple hardware counters for counting transmitted
packets larger than 1518 octets. Each counter counts the packets
in specific range.
We accumulate those counters to have a single counter.
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
When the mlx5 health mechanism detects a problem while the driver
is in the middle of init_one or remove_one, the driver needs to prevent
the health mechanism from scheduling future work; if future work
is scheduled, there is a problem with use-after-free: the system WQ
tries to run the work item (which has been freed) at the scheduled
future time.
Prevent this by disabling work item scheduling in the health mechanism
when the driver is in the middle of init_one() or remove_one().
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
All other mlx5_events report the port number as 1 based, which is how FW
reports it in the port event EQE. Reporting 0 for this event causes
mlx5_ib to not raise a fatal event notification to registered clients
due to a seemingly invalid port.
All switch cases in mlx5_ib_event that go through the port check are
supposed to set the port now, so just do it once at variable
declaration.
Linux commit:
aba462134634b502d720e15b23154f21cfa277e5
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
The user can provide very large cqe_size which will cause to integer
overflow.
Linux commit:
28e9091e3119933c38933cb8fc48d5618eb784c8
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
If power exceed the slot limit, or slot limit is unknown the ConnectX-6
firmware will shutdown its port.
Inform the user via debug message.
MFC after: 3 days
Approved by: hselasky (mentor), kib (mentor)
Sponsored by: Mellanox Technologies
The receive side scaling stride parameter is a value which define the interval
between active receive side queues. The traffic for the inactive queues is
redirected to the nearest active queue by use of modulus. The default value
of this parameter is one, which means all receive side queues are used.
The point of this feature is to redirect more traffic to fewer receive side
queues in order to take more advantage of sorted large receive offload,
sorted LRO. The sorted LRO works better when more packets are accumulated
per service interval.
MFC after: 3 days
Approved by: re (marius)
Sponsored by: Mellanox Technologies
Inspecting the PRM no more than 0x3F data segments, DS, of size 16 bytes is
allowed.
Worst case scenario summary of DS usage:
Header is fixed: 2 DS
Maximum inlining: 98 => (98 - 2) / 16 = 6 DS
Remainder: 0x3F - 2 - 6 = 55 DS (mbuf frags)
Previously a value of 56 DS was used and this would work in the
normal case because not all inline data area was used up.
MFC after: 3 days
Approved by: re (marius)
Sponsored by: Mellanox Technologies
Query the minimal inline mode supported by the card.
When creating a send queue, cache the queried mode and optimize the transmit
if no inlining is required. In this case, we can avoid touching the headers
cache line and avoid dirtying several more lines by copying headers into
the send WQEs. Also, if no inline headers are used, hardware assists in
the VLAN tag framing.
Submitted by: kib@, slavash@
MFC after: 1 week
Sponsored by: Mellanox Technologies
For setups having a large amount of PCI devices, it makes sense to limit the
number of MSIX vectors per PCI device, in order to avoid running out of IRQ
vectors.
MFC after: 1 week
Sponsored by: Mellanox Technologies
The scatter list is formed by the chunks of MCLBYTES each, and larger
than default packets are returned to the stack as the mbuf chain.
Submitted by: kib@
MFC after: 1 week
Sponsored by: Mellanox Technologies
To access the data, set sysctl dev.mce.N.conf.debug_stats to 1.
This enables the sysctl node dev.mce.N.hw_ctx_debug. Its content is
the mapping of each channel' number to used receive queue and associated
completion queue, set of the transmit queues numbers and corresponding
completion queues.
Trimmed example output:
channel 30 rq 188 cq 1085
channel 30 tc 0 sq 187 cq 1084
channel 31 rq 191 cq 1087
channel 31 tc 0 sq 190 cq 1086
MFC after: 1 week
Sponsored by: Mellanox Technologies
Device detach and setting error state may deadlock over the interface mutex
like this:
a) Detach code in mlx5en waits until error state is set while the interface
mutex is locked.
b) The set error handler needs to lock the interface mutex before it can
set the error state.
The solution is to use atomics to set the error state.
MFC after: 1 week
Sponsored by: Mellanox Technologies
When resetting mlx5core instances it can happen that the order of attach and
detach for mlx5ib instances is changed. Take the unit number for mlx5_%d from
the parent PCI device, similarly to what is done in mlx5en(4), so that there
is a direct relationship between mce<N> and mlx5_<N>.
MFC after: 1 week
Sponsored by: Mellanox Technologies
The DSCP feature is controlled using a set of sysctl(8) fields under
the qos sysctl directory entry for mlx5en(4).
For Routable RoCE QPs, the DSCP should be set in the QP's address path.
The DSCP's value is derived from the traffic class.
Linux commit:
ed88451e1f2d400fd6a743d0a481631cf9f97550
MFC after: 1 week
Sponsored by: Mellanox Technologies
When receiving a PCP change all GID entries are reloaded.
This ensures the relevant GID entries use prio tagging,
by setting VLAN present and VLAN ID to zero.
The priority for prio tagged traffic is set using the regular
rdma_set_service_type() function.
Fake the real network device to have a VLAN ID of zero
when prio tagging is enabled. This is logic is hidden inside
the rdma_vlan_dev_vlan_id() function which must always be used
to retrieve the VLAN ID throughout all of ibcore and the
infiniband network drivers.
The VLAN presence information then propagates through all
of ibcore and so incoming connections will have the VLAN
bit set. The incoming VLAN ID is then checked against the
return value of rdma_vlan_dev_vlan_id().
MFC after: 1 week
Sponsored by: Mellanox Technologies
The hardware rate limiting feature is enabled by the RATELIMIT kernel
option. Please refer to ifconfig(8) and the txrtlmt option and the
SO_MAX_PACING_RATE set socket option for more information. This
feature is compatible with hardware transmit send offload, TSO.
A set of sysctl(8) knobs under dev.mce.<N>.rate_limit are provided to
setup the ratelimit table and also to fine tune various rate limit
related parameters.
Sponsored by: Mellanox Technologies
According to the 802.1Q-2014 9.6 VLAN Tag Control Information, VID value 0
means that there is no VLAN tag assigned to the packet, and only PCP and
DEI values from the tag are meaningful. Current flow table programming
filter out such packets.
When programming VLAN filter for flow table, unconditionally add rule which
accept packets with VLAN id 0. The packets are already handled correctly
by the network stack.
Reviewed by: hselasky, slavash
Sponsored by: Mellanox Technologies
MFC after: 1 week
Make sure the command completion handler is not called when the device is
in internal error state. This can easily trigger use after free situations.
MFC after: 3 days
Sponsored by: Mellanox Technologies
During health care IRQ resources will be reallocated.
Newbus requires that Giant is locked before accessing
these resources.
MFC after: 3 days
Sponsored by: Mellanox Technologies
Firmware dump collecting should be triggered in case firmware syndrome
with request for reset bit is set.
MFC after: 3 days
Submitted by: slavash@
Sponsored by: Mellanox Technologies
- Move the semaphore locking and unlocking to the same function.
- Flags are no longer needed if the reset and crdump will be done in the
same function.
MFC after: 3 days
Submitted by: slavash@
Sponsored by: Mellanox Technologies
- Move firmware dump prep and cleanup to init_one() and remove_one() so that
the init and cleanup will happen only upon driver reload.
- Add some prints to indicate firmware dump.
MFC after: 3 days
Submitted by: slavash@
Sponsored by: Mellanox Technologies
The old code checked for MLX5_CR_SPACE_DOMAIN which is irrelevant here.
However, if dev->vsec_addr would be 0, an access to wrong offset would
happen.
MFC after: 3 days
Submitted by: slavash@
Sponsored by: Mellanox Technologies
This fixes 32-bit compat (no ioctl command defintions are required
as struct ifreq is the same size). This is believed to be sufficent to
fully support ifconfig on 32-bit systems.
Reviewed by: kib
Obtained from: CheriBSD
MFC after: 1 week
Relnotes: yes
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D14900
error state.
If the device is in internal error state the hardware will not
generate completions. Just move on to destroy the resources.
Submitted by: slavash@
MFC after: 1 week
Sponsored by: Mellanox Technologies
Change page cleanup flow when in internal error to properly decrement
the page counts when reclaiming pages. That prevents timing out
waiting for extra pages that were actually cleaned up previously.
Submitted by: slavash@
MFC after: 1 week
Sponsored by: Mellanox Technologies
When a PCI error is detected the PCI state could be corrupt, don't
save it in that flow. Save the state after initialization. After
restoring the PCI state during slot reset save it again, restoring
the state destroys the previously saved state info.
Submitted by: slavash@
MFC after: 1 week
Sponsored by: Mellanox Technologies
Since the FW can be shared between PCI functions it is common that
more than one health poll will detected a failure, this can lead to
multiple resets.
The solution is to use a FW locking mechanism using semaphore space to
provide a way to synchronize between functions. The FW semaphore is
acquired via config cycle access. First the VSEC gateway must be
acquired, then the semaphore can be locked by writing a value to it
and confirmed it's locked by reading the same value back. The process
in the same to free the semaphore, except the value written should be
zero.
Submitted by: slavash@
MFC after: 1 week
Sponsored by: Mellanox Technologies
If a FW assert is considered fatal, indicated by a new bit in the
health buffer, reset the FW. After the reset, follow the normal
recovery flow.
Submitted by: slavash@
MFC after: 1 week
Sponsored by: Mellanox Technologies
Some mlx5 adapter firmware allows the driver to reset the firmware in
the event of an error. When a software reset is issued on any physical
function all PFs enter reset state. This is a recoverable condition.
The existing recovery flow was designed to allow the recovery of a
VF after a PF driver reload. This patch expands the scope of that
flow to recover PFs or VFs after a SW reset has been issued.
When a software reset is issued the following occurs:
1. The NIC interface mode is set to SW_RESET (7) while the reset is in
progress.
2. Once the reset completes the NIC interface mode is set to NIC
disabled (1).
After the reset has been issued (added in a subsequent patch) the
health poll for other functions will detect that the NIC interface
state has been set to disabled. This will cause it to enter the
existing recovery flow. If the PCI is still working (meaning it
doesn't return 0xff on all reads) it means recovery can proceed
immediately instead of waiting 60 seconds.
The error detetion has also been refactored to avoid incorrect or
misleading log messages.
Submitted by: slavash@
MFC after: 1 week
Sponsored by: Mellanox Technologies
When mlx5_enter_error_state() operation is forced by shutdown, the
messages surrounding setting the error state are not informational
and confuse users.
Submitted by: kib@
MFC after: 1 week
Sponsored by: Mellanox Technologies
This patch accumulates the following Linux commits:
- 8812c24d28f4972c4f2b9998bf30b1f2a1b62adf
net/mlx5: Add fast unload support in shutdown flow
- 59211bd3b6329c3e5f4a90ac3d7f87ffa7867073
net/mlx5: Split the load/unload flow into hardware and software flows
- 4525abeaae54560254a1bb8970b3d4c225d32ef4
net/mlx5: Expose command polling interface
Submitted by: Matthew Finlay <matt@mellanox.com>
MFC after: 1 week
Sponsored by: Mellanox Technologies
This patch accumulates the following Linux commits:
- 04c0c1ab38e95105d950db5b84e727637e149ce7
net/mlx5: PCI error recovery health care simulation
- 0179720d6be2096b8d0a4d143254ff9e77747daa
net/mlx5: Introduce trigger_health_work function
- 3fece5d676939f42f434c63dfe1bd42d7d94e6f0
net/mlx5: Continue health polling until it is explicitly stopped
Submitted by: Matthew Finlay <matt@mellanox.com>
MFC after: 1 week
Sponsored by: Mellanox Technologies
The mlx5e_destroy_ifp() function may be called from the system workqueue and
in this case trying to flush all works will cause a dead lock.
Instead of using the system workqueue, create a designated workqueue
for each mlx5en(4) device instance.
Submitted by: slavash@
MFC after: 1 week
Sponsored by: Mellanox Technologies
There is a difference when parsing a completion entry between Ethernet
and IB ports. When link layer is Ethernet the bits describe the type of
L3 header in the packet. In the case when link layer is Ethernet and VLAN
header is present the value of SL is equal to the 3 UP bits in the VLAN
header. If VLAN header is not present then the SL is undefined and consumer
of the completion should check if IB_WC_WITH_VLAN is set.
While that, this patch also fills the vlan_id field in the completion if
present.
linux commit 12f8fedef2ec94c783f929126b20440a01512c14
MFC after: 1 week
Sponsored by: Mellanox Technologies
mlx5core.
Do not consider the inability to create a firmware dump fatal, but
inform about the situation and allow the driver to attach. The device
might not implement the needed VSC, or we might not know the layout of
the registers map. In either case, only firmware dump functionality is
limited, the network operations should be fine.
Submitted by: kib@
MFC after: 1 week
Sponsored by: Mellanox Technologies
When the mlx5en(4) driver was converted to using BUSDMA(9) the call to
m_defrag() was moved after the part of the TX routine that strips the
header from the mbuf chain. Before it called m_defrag it first trimmed
off the now-empty mbufs from the start of the chain. This has the side
effect of also removing the head of the chain that has M_PKTHDR set.
m_defrag() will not defrag a chain that does not have M_PKTHDR set,
thus it was effectively never defragging the mbuf chains.
As it turns out, trimming the mbufs in this fashion is unnecessary since
the call to bus_dmamap_load_mbuf_sg doesn't map empty mbufs anyway, so
remove it.
Differential Revision: https://reviews.freebsd.org/D12050
Submitted by: mjoras@
MFC after: 1 week
Sponsored by: Mellanox Technologies
Set and report vport MTU rather than physical MTU,
The driver will set both vport and physical port mtu
and will rely on the query of vport mtu.
SRIOV VFs have to report their MTU to their vport manager (PF),
and this will allow them to work with any MTU they need
without failing the request.
Also for some cases where the PF is not a port owner, PF can
work with MTU less than the physical port mtu if set physical
port mtu didn't take effect.
Based on Linux upstream commit:
cd255efff9baadd654d6160e52d17ae7c568c9d3
Submitted by: Meny Yossefi <menyy@mellanox.com>
MFC after: 1 week
Sponsored by: Mellanox Technologies
Currently the ifnet interface is named mceX, where X is a monotonically
incremented value. If the device is reset due to a fatal error, then the
interface name will change. Using the device unit number will keep the
naming consistent across the reset logic.
Submitted by: Matthew Finlay <matt@mellanox.com>
MFC after: 1 week
Sponsored by: Mellanox Technologies
ConnectX-4/5 devices in mlx5core.
The dump is obtained by reading a predefined register map from the
non-destructive crspace, accessible by the vendor-specific PCIe
capability (VSC). The dump is stored in preallocated kernel memory and
managed by the mlx5tool(8), which communicates with the driver using a
character device node.
The utility allows to store the dump in format
<address> <value>
into a file, to reset the dump content, and to manually initiate the
dump.
A call to mlx5_fwdump() should be added at the places where a dump
must be fetched automatically. The most likely place is right before a
firmware reset request.
Submitted by: kib@
MFC after: 1 week
Sponsored by: Mellanox Technologies
Add the ability to access the vendor specific space gateway in order
to support reading and writing data into the different configuration
domains.
Submitted by: Matthew Finlay <matt@mellanox.com>
MFC after: 1 week
Sponsored by: Mellanox Technologies
Add support for PFC and implement reading the per priority statistics
using the sysctl(8) interface. PFC is used together with VLAN priority
and can be enabled and disabled on a per priority basis.
Global pause frames and PFC are incompatible features and surrounding
logic has been added to warn the user about misconfiguration.
Update relevant mlx5core APIs for PFC configuration.
MFC after: 1 week
Sponsored by: Mellanox Technologies
ECN configuration and statistics is available through a set of sysctl(8)
nodes under sys.class.infiniband.mlx5_X.cong . The ECN configuration
nodes can also be used as loader tunables.
MFC after: 1 week
Sponsored by: Mellanox Technologies
This patch accumulates the following Linux commits:
mlx5_health.c
- 78ccb25861d76a8fc5c678d762180e6918834200
mlx5_core: Fix wrong name in struct
- 171bb2c560f45c0427ca3776a4c8f4e26e559400
mlx5_core: Update health syndromes
- 0144a95e2ad53a40c62148f44fb0c1f9d2a0d1e9
mlx5_core: Use accessor functions to read from device memory
- ac6ea6e81a80172612e0c9ef93720f371b198918
mlx5_core: Use private health thread for each device
- fd76ee4da55abb21babfc69310d321b9cb9a32e0
mlx5_core: Fix internal error detection conditions
- 2241007b3d783cbdbaa78c30bdb1994278b6f9b9
mlx5: Clear health sick bit when starting health poll
- 712bfef60912d91033cb25739f7444d5b8d8c59f
mlx5: Fix version printout in case of health issue
- 89d44f0a6c732db23b219be708e2fe1e03ee4842
mlx5_core: Add pci error handlers to mlx5_core driver
mlx5_cmd.c
- be87544de8df2b1eb34bcb5e32691287d96f9ec4
mlx5_core: Fix async commands return code
- a31208b1e11df334d443ec8cace7636150bb8ce2
mlx5_core: New init and exit flow for mlx5_core
- 020446e01eebc9dbe7eda038e570ab9c7ab13586
mlx5_core: Prepare cmd interface to system errors handling
- 89d44f0a6c732db23b219be708e2fe1e03ee4842
mlx5_core: Add pci error handlers to mlx5_core driver
- 0d834442cc247c7b3f3bd6019512ae03e96dd99a
mlx5: Fix teardown errors that happen in pci error handler
mlx5_main.c
- 5fc7197d3a256d9c5de3134870304b24892a4908
mlx5: Add pci shutdown callback
Submitted by: Matthew Finlay <matt@mellanox.com>
MFC after: 1 week
Sponsored by: Mellanox Technologies
Add support for mapping priority to traffic class via sysctl
Submitted by: Slava Shwartsman <slavash@mellanox.com>
MFC after: 1 week
Sponsored by: Mellanox Technologies
- Factor out port speed definitions into new port.h header file,
similarly as done in Linux upstream.
- Correct two existing port speed definitions in mlx5en according to
Linux upstream.
MFC after: 1 week
Sponsored by: Mellanox Technologies
Adding an interface might be done outside the device_attach() routine
and will then cause a panic, due to the VNET not being set.
MFC after: 1 week
Sponsored by: Mellanox Technologies
The current implementation does not handle timeout in case of command
with callback request, and this can lead to deadlock if the command
doesn't get firmware response. Add delayed callback timeout work
before posting the command to firmware. In case of real firmware
command completion we will cancel the delayed work. In case of
firmware command timeout the callback timeout handler will be called
and it will simulate firmware completion with timeout error.
linux commit 65ee67084589c1783a74b4a4a5db38d7264ec8b5
MFC after: 1 week
Sponsored by: Mellanox Technologies
