of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
has support for the .codeXX directives). However, it is desirable, for
a time, to allow kernels to be built with clang 3.4. Historically, it
has been advantageous to allow stable X-1 to build kernels the old
way (so long as the impact of doing so is small), and this restores
that ability.
Also, centralize the addition of ${ASM_CFLAGS.${.IMPSRC}}, place it in
kern.mk rather than kern.pre.mk so that all modules can benefit, and
give the same treatment to CFLAGS in kern.mk as well.
building with gcc 4.2
This has been requested several times over the past few months by several
people (including me), because gcc 4.2 just gets it wrong too often. It's
causing us to litter the code with lots of bogus initializers just to
squelch the warnings. We still have clang and coverity telling us about
uninitialized variables, and they do so more accurately.
mostly paves the way for the new pmap code, and shouldn't result in any
noticible behavior differences.
Submitted by: Svatopluk Kraus <onwahe@gmail.com>,
Michal Meloun <meloun@miracle.cz
CWARNFALGS.$file centrally so we don't have to have it in all the
places. Remove a few warning flags that are no longer needed.
Also, always use -Wno-unknown-pragma to (hopefully temporarily) work
around #pragma ident in debug.h in the opensolaris code. Remove some
stale warning suppression that's no longer necessary.
roughly 10 years, and the driver has not enjoyed any significant maintenance
since long before that. Despite well-meaning efforts from a number of
people, myself included, it never made the jump to 64-bit and was relegated
to the back-corners of i386. Now its frailty is hampering forward progress
with Clang. Any renewed engineering efforts are of course welcome and can
happen outside of the tree. No MFC of this is planned.
When we started compiling the kernel with -march=armv7 the compiler
started emitting new types of relocation info which are incompatible with
the shared-lib file format used by .ko modules. This workaround prevents
the compiler from emitting the instruction sequences that require the
new relocs. This amounts to using an undocumented internal compiler
flag, so this is just a temporary workaround while we look for a good fix.
PR: 196407
the place where the C dialect is selected. Have a fairly long list
of newly requires warning suppression for clang 3.5.0, also
centralized in kern.mk. Survive the fallout of the removal of
bsd.sys.mk from bsd.kmod.mk.
raft of new warnings that appear to be on by default in clang 3.5.0.
Fix RPI-B build issues with new clang not liking the ability to pass
arbitrary flags to as, since some flags are more arbitrary (and thus
verboten) than others.
These warnings should be actually fixed in the code, but this is a
band-aide to get things (almost) building again.
a) Front load as much work as possible in if_transmit, before any driver
lock or software queue has to get involved.
b) Replace buf_ring with a brand new mp_ring (multiproducer ring). This
is specifically for the tx multiqueue model where one of the if_transmit
producer threads becomes the consumer and other producers carry on as
usual. mp_ring is implemented as standalone code and it should be
possible to use it in any driver with tx multiqueue. It also has:
- the ability to enqueue/dequeue multiple items. This might become
significant if packet batching is ever implemented.
- an abdication mechanism to allow a thread to give up writing tx
descriptors and have another if_transmit thread take over. A thread
that's writing tx descriptors can end up doing so for an unbounded
time period if a) there are other if_transmit threads continuously
feeding the sofware queue, and b) the chip keeps up with whatever the
thread is throwing at it.
- accurate statistics about interesting events even when the stats come
at the expense of additional branches/conditional code.
The NIC txq lock is uncontested on the fast path at this point. I've
left it there for synchronization with the control events (interface
up/down, modload/unload).
c) Add support for "type 1" coalescing work request in the normal NIC tx
path. This work request is optimized for frames with a single item in
the DMA gather list. These are very common when forwarding packets.
Note that netmap tx in cxgbe already uses these "type 1" work requests.
d) Do not request automatic cidx updates every 32 descriptors. Instead,
request updates via bits in individual work requests (still every 32
descriptors approximately). Also, request an automatic final update
when the queue idles after activity. This means NIC tx reclaim is still
performed lazily but it will catch up quickly as soon as the queue
idles. This seems to be the best middle ground and I'll probably do
something similar for netmap tx as well.
e) Implement a faster tx path for WRQs (used by TOE tx and control
queues, _not_ by the normal NIC tx). Allow work requests to be written
directly to the hardware descriptor ring if room is available. I will
convert t4_tom and iw_cxgbe modules to this faster style gradually.
MFC after: 2 months
code alongside the existing implementation and quickly toggle between
the two implementations when testing. Once the new code is past its
teething stage we can remove this option.
initially set up the MMU. Some day they may also be useful as part of
suspend/resume handling, when we get better at power management.
Submitted by: Svatopluk Kraus <onwahe@gmail.com>,
Michal Meloun <meloun@miracle.cz
mechanism defined for armv7 (and also present on some armv6 chips including
the arm1176 used on rpi). The information is parsed into a global cpuinfo
structure, which will be used by (upcoming) new cache and tlb maintenance
code to handle cpu-specific variations of the maintence sequences.
Submitted by: Svatopluk Kraus <onwahe@gmail.com>,
Michal Meloun <meloun@miracle.cz
images into the kernel as currently included into iwn6000g2{a,b}fw.ko
and delete the old files, missed in r254199 and r259135 respectively.
MFC after: 3 days
which means that the NFSCLIENT and NFSSERVER
kernel options will no longer work. This commit
only removes the kernel components. Removal of
unused code in the user utilities will be done
later. This commit does not include an addition
to UPDATING, but that will be committed in a
few minutes.
Discussed on: freebsd-fs
the orphaned descendants. Base of the API is modelled after the same
feature from the DragonFlyBSD.
Requested by: bapt
Reviewed by: jilles (previous version)
Tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 3 weeks
for counter mode), and AES-GCM. Both of these modes have been added to
the aesni module.
Included is a set of tests to validate that the software and aesni
module calculate the correct values. These use the NIST KAT test
vectors. To run the test, you will need to install a soon to be
committed port, nist-kat that will install the vectors. Using a port
is necessary as the test vectors are around 25MB.
All the man pages were updated. I have added a new man page, crypto.7,
which includes a description of how to use each mode. All the new modes
and some other AES modes are present. It would be good for someone
else to go through and document the other modes.
A new ioctl was added to support AEAD modes which AES-GCM is one of them.
Without this ioctl, it is not possible to test AEAD modes from userland.
Add a timing safe bcmp for use to compare MACs. Previously we were using
bcmp which could leak timing info and result in the ability to forge
messages.
Add a minor optimization to the aesni module so that single segment
mbufs don't get copied and instead are updated in place. The aesni
module needs to be updated to support blocked IO so segmented mbufs
don't have to be copied.
We require that the IV be specified for all calls for both GCM and ICM.
This is to ensure proper use of these functions.
Obtained from: p4: //depot/projects/opencrypto
Relnotes: yes
Sponsored by: FreeBSD Foundation
Sponsored by: NetGate
Mave the grant table code into the dev/xen folder in preparation for turning
it into a device using the newbus interface. This is just code motion, no
functional changes.
Sponsored by: Citrix Systems R&D
When running as a Xen PVH Dom0 we need to add custom buses that override
some of the functionality present in the ACPI PCI Bus and the PCI Bus. We
currently override the ACPI PCI Bus, but not the PCI Bus, so add a new
override for the PCI Bus and share the generic functions between them.
Reported by: David P. Discher <dpd@dpdtech.com>
Sponsored by: Citrix Systems R&D
conf/files.amd64:
- Add the new files.
x86/xen/xen_pci_bus.c:
- Generic file that contains the PCI overrides so they can be used by the
several PCI specific buses.
xen/xen_pci.h:
- Prototypes for the generic overried functions.
dev/xen/pci/xen_pci.c:
- Xen specific override for the PCI bus.
dev/xen/pci/xen_acpi_pci.c:
- Xen specific override for the ACPI PCI bus.
to automatically set the armv6 option when MACHINE_ARCH is armv6. That
allows replacing ever-growing lists of cpu names as options to compile
a given file with the using either "optional armv6" or "optional !armv6".
partitions. Several utilities still use this interface and require
additional information since gpart was activated than before. This
allows fsck of a UFS partition without having to specify it is UFS,
per historic behavior.
have chosen different (and more traditional) stateless/statuful
NAT64 as translation mechanism. Last non-trivial commits to both
faith(4) and faithd(8) happened more than 12 years ago, so I assume
it is time to drop RFC3142 in FreeBSD.
No objections from: net@
Split it into two modules: if_gre(4) for GRE encapsulation and
if_me(4) for minimal encapsulation within IP.
gre(4) changes:
* convert to if_transmit;
* rework locking: protect access to softc with rmlock,
protect from concurrent ioctls with sx lock;
* correct interface accounting for outgoing datagramms (count only payload size);
* implement generic support for using IPv6 as delivery header;
* make implementation conform to the RFC 2784 and partially to RFC 2890;
* add support for GRE checksums - calculate for outgoing datagramms and check
for inconming datagramms;
* add support for sending sequence number in GRE header;
* remove support of cached routes. This fixes problem, when gre(4) doesn't
work at system startup. But this also removes support for having tunnels with
the same addresses for inner and outer header.
* deprecate support for various GREXXX ioctls, that doesn't used in FreeBSD.
Use our standard ioctls for tunnels.
me(4):
* implementation conform to RFC 2004;
* use if_transmit;
* use the same locking model as gre(4);
PR: 164475
Differential Revision: D1023
No objections from: net@
Relnotes: yes
Sponsored by: Yandex LLC
problems than it solves. SYSDIR is already defined almost always and
can be used instead. Working around the one case where it isn't is
much easier than working around the fact that @ may not exist in 18
other places.
Differential Revision: https://reviews.freebsd.org/D1100
875. This intersects with the agp_i810.c, which supports all Intels
from i810 to Core i5/7. Both agp_intel.c and agp_i810.c are compiled
into kernel when device agp is specified in config, and agp_i810
attach seems to be selected by chance due to linking order.
Strip support for 810 and later from agp_intel.c. Since 440-class
chipsets do not support any long-mode capable CPUs, remove agp_intel.c
from amd64 kernel file list. Note that agp_intel.c is not compiled
into agp.ko on amd64 already.
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
This code has had an extensive rewrite and a good series of reviews, both by the author and other parties. This means a lot of code has been simplified. Pluggable structures for high-rate entropy generators are available, and it is most definitely not the case that /dev/random can be driven by only a hardware souce any more. This has been designed out of the device. Hardware sources are stirred into the CSPRNG (Yarrow, Fortuna) like any other entropy source. Pluggable modules may be written by third parties for additional sources.
The harvesting structures and consequently the locking have been simplified. Entropy harvesting is done in a more general way (the documentation for this will follow). There is some GREAT entropy to be had in the UMA allocator, but it is disabled for now as messing with that is likely to annoy many people.
The venerable (but effective) Yarrow algorithm, which is no longer supported by its authors now has an alternative, Fortuna. For now, Yarrow is retained as the default algorithm, but this may be changed using a kernel option. It is intended to make Fortuna the default algorithm for 11.0. Interested parties are encouraged to read ISBN 978-0-470-47424-2 "Cryptography Engineering" By Ferguson, Schneier and Kohno for Fortuna's gory details. Heck, read it anyway.
Many thanks to Arthur Mesh who did early grunt work, and who got caught in the crossfire rather more than he deserved to.
My thanks also to folks who helped me thresh this out on whiteboards and in the odd "Hallway track", or otherwise.
My Nomex pants are on. Let the feedback commence!
Reviewed by: trasz,des(partial),imp(partial?),rwatson(partial?)
Approved by: so(des)
Multipass device attachment was tested on many arm platforms by users and
only success was reported on the arm@ mailing list. This is just the
long-delayed followup of making it the default.
Multipass attachment is necessary when using vendor-supplied FDT data,
because our devices may need to be attached in a different order than they
are described in the FDT data.
This device is only attached to priviledged domains, and allows the
toolstack to interact with Xen. The two functions of the privcmd
interface is to allow the execution of hypercalls from user-space, and
the mapping of foreign domain memory.
Sponsored by: Citrix Systems R&D
i386/include/xen/hypercall.h:
amd64/include/xen/hypercall.h:
- Introduce a function to make generic hypercalls into Xen.
xen/interface/xen.h:
xen/interface/memory.h:
- Import the new hypercall XENMEM_add_to_physmap_range used by
auto-translated guests to map memory from foreign domains.
dev/xen/privcmd/privcmd.c:
- This device has the following functions:
- Allow user-space applications to make hypercalls into Xen.
- Allow user-space applications to map memory from foreign domains,
this is accomplished using the newly introduced hypercall
(XENMEM_add_to_physmap_range).
xen/privcmd.h:
- Public ioctl interface for the privcmd device.
x86/xen/hvm.c:
- Remove declaration of hypercall_page, now it's declared in
hypercall.h.
conf/files:
- Add the privcmd device to the build process.
The user-space event channel device is used by applications to receive
and send event channel interrupts. This device is based on the Linux
evtchn device.
Sponsored by: Citrix Systems R&D
xen/evtchn/evtchn_dev.c:
- Remove the old event channel device, which was already disabled in
the build system.
dev/xen/evtchn/evtchn_dev.c:
- Import a new event channel device based on the one present in
Linux.
- This device allows the following operations:
- Bind VIRQ event channels (ioctl).
- Bind regular event channels (ioctl).
- Create and bind new event channels (ioctl).
- Unbind event channels (ioctl).
- Send notifications to event channels (ioctl).
- Reset the device shared memory ring (ioctl).
- Unmask event channels (write).
- Receive event channel upcalls (read).
- The new code is MP safe, and can be used concurrently.
conf/files:
- Add the new device to the build system.
vxlan creates a virtual LAN by encapsulating the inner Ethernet frame in
a UDP packet. This implementation is based on RFC7348.
Currently, the IPv6 support is not fully compliant with the specification:
we should be able to receive UPDv6 packets with a zero checksum, but we
need to support RFC6935 first. Patches for this should come soon.
Encapsulation protocols such as vxlan emphasize the need for the FreeBSD
network stack to support batching, GRO, and GSO. Each frame has to make
two trips through the network stack, and each frame will be at most MTU
sized. Performance suffers accordingly.
Some latest generation NICs have begun to support vxlan HW offloads that
we should also take advantage of. VIMAGE support should also be added soon.
Differential Revision: https://reviews.freebsd.org/D384
Reviewed by: gnn
Relnotes: yes
vestige of a time when we needed to do that, but it is all handled by
beforedepend now. When we depend on the symlink, bmake will cause the
file to be rebuilt always.
With this change, dtrace.ko doesn't rebuild every time through a
KERNFAST run.
Sponsored by: Netfix
For compatibility, 'device windtunnel' is still supported, but one should use
'device adm1030' instead, and this has been updated in GENERIC and NOTES.
The powerpc support was the only supported architecture not prepending the elf format name
with "-freebsd" in base this change makes it consistent with other architectures.
On newer version of binutils the powerpc format is also prepended with "-freebsd".
Also modify the kernel ldscripts in that regards.
As a result it is now possible cross build the kernel on powerpc using newer binutils
Differential Revision: https://reviews.freebsd.org/D926
Differential Revision: https://reviews.freebsd.org/D928
syscalls themselves are tightly coupled with the network stack and
therefore should not be in the generic socket code.
The following four syscalls have been marked as NOSTD so they can be
dynamically registered in sctp_syscalls_init() function:
sys_sctp_peeloff
sys_sctp_generic_sendmsg
sys_sctp_generic_sendmsg_iov
sys_sctp_generic_recvmsg
The syscalls are also set up to be dynamically registered when COMPAT32
option is configured.
As a side effect of moving the SCTP syscalls, getsock_cap needs to be
made available outside of the uipc_syscalls.c source file. A proper
prototype has been added to the sys/socketvar.h header file.
API tests from the SCTP reference implementation have been run to ensure
compatibility. (http://code.google.com/p/sctp-refimpl/source/checkout)
Submitted by: Steve Kiernan <stevek@juniper.net>
Reviewed by: tuexen, rrs
Obtained from: Juniper Networks, Inc.
interrupts and report the largest value seen as sysctl
debug.max_kstack_used. Useful to estimate how close the kernel stack
size is to overflow.
In collaboration with: Larry Baird <lab@gta.com>
Sponsored by: The FreeBSD Foundation (kib)
MFC after: 1 week
the oabi is still in the tree, but it is expected this will be removed
as developers work on surrounding code.
With this commit the ARM EABI is the only supported supported ABI by
FreeBSD on ARMa 32-bit processors.
X-MFC after: never
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D876
This device is used by the user-space daemon that runs xenstore
(xenstored). It allows xenstored to map the xenstore memory page, and
reports the event channel xenstore is using.
Sponsored by: Citrix Systems R&D
dev/xen/xenstore/xenstored_dev.c:
- Add the xenstored character device that's used to map the xenstore
memory into user-space, and to report the event channel used by
xenstore.
conf/files:
- Add the device to the build process.
Move xenstore related devices (xenstore.c and xenstore_dev.c) from
xen/xenstore to dev/xen/xenstore. This is just code motion, no
functional changes.
Sponsored by: Citrix Systems R&D
This patch adds support for MSI interrupts when running on Xen. Apart
from adding the Xen related code needed in order to register MSI
interrupts this patch also makes the msi_init function a hook in
init_ops, so different MSI implementations can have different
initialization functions.
Sponsored by: Citrix Systems R&D
xen/interface/physdev.h:
- Add the MAP_PIRQ_TYPE_MULTI_MSI to map multi-vector MSI to the Xen
public interface.
x86/include/init.h:
- Add a hook for setting custom msi_init methods.
amd64/amd64/machdep.c:
i386/i386/machdep.c:
- Set the default msi_init hook to point to the native MSI
initialization method.
x86/xen/pv.c:
- Set the Xen MSI init hook when running as a Xen guest.
x86/x86/local_apic.c:
- Call the msi_init hook instead of directly calling msi_init.
xen/xen_intr.h:
x86/xen/xen_intr.c:
- Introduce support for registering/releasing MSI interrupts with
Xen.
- The MSI interrupts will use the same PIC as the IO APIC interrupts.
xen/xen_msi.h:
x86/xen/xen_msi.c:
- Introduce a Xen MSI implementation.
x86/xen/xen_nexus.c:
- Overwrite the default MSI hooks in the Xen Nexus to use the Xen MSI
implementation.
x86/xen/xen_pci.c:
- Introduce a Xen specific PCI bus that inherits from the ACPI PCI
bus and overwrites the native MSI methods.
- This is needed because when running under Xen the MSI messages used
to configure MSI interrupts on PCI devices are written by Xen
itself.
dev/acpica/acpi_pci.c:
- Lower the quality of the ACPI PCI bus so the newly introduced Xen
PCI bus can take over when needed.
conf/files.i386:
conf/files.amd64:
- Add the newly created files to the build process.
- Use bus_*() instead of bus_space_*().
- Use device_printf().
- Remove unused global variables and the extra warning suppression
they required.
- Use callout() instead of timeout().
Reviewed by: se
For now restrict it to amd64. Other architectures might be
re-added later once tested.
Remove the drivers from the global NOTES and files files and move
them to the amd64 specifics.
Remove the drivers from the i386 modules build and only leave the
amd64 version.
Rather than depending on "inet" depend on "pci" and make sure that
ixl(4) and ixlv(4) can be compiled independently [2]. This also
allows the drivers to build properly on IPv4-only or IPv6-only
kernels.
PR: 193824 [2]
Reviewed by: eric.joyner intel.com
MFC after: 3 days
References:
[1] http://lists.freebsd.org/pipermail/svn-src-all/2014-August/090470.html
for amd64/linux32. Fix the entirely bogus (untested) version from
r161310 for i386/linux using the same shared code in compat/linux.
It is unclear to me if we could support more clock mappings but
the current set allows me to successfully run commercial
32bit linux software under linuxolator on amd64.
Reviewed by: jhb
Differential Revision: D784
MFC after: 3 days
Sponsored by: DARPA, AFRL
The flowdirector feature shares on-chip memory with other things
such as the RX buffers. In theory it should be configured in a way
that doesn't interfere with the rest of operation. In practice,
the RX buffer calculation didn't take the flow-director allocation
into account and there'd be overlap. This lead to various garbage
frames being received containing what looks like internal NIC state.
What _I_ saw was traffic ending up in the wrong RX queues.
If I was doing a UDP traffic test with only one NIC ring receiving
traffic, everything is fine. If I fired up a second UDP stream
which came in on another ring, there'd be a few percent of traffic
from both rings ending up in the wrong ring. Ie, the RSS hash would
indicate it was supposed to come in ring X, but it'd come in ring Y.
However, when the allocation was fixed up, the developers at Verisign
still saw traffic stalls.
The flowdirector feature ends up fiddling with the NIC to do various
attempts at load balancing connections by populating flow table rules
based on sampled traffic. It's likely that all of that has to be
carefully reviewed and made less "magic".
So for now the flow director feature is disabled (which fixes both
what I was seeing and what they were seeing) until it's all much
more debugged and verified.
Tested:
* (me) 82599EB 2x10G NIC, RSS UDP testing.
* (verisign) not sure on the NIC (but likely 82599), 100k-200k/sec TCP
transaction tests.
Submitted by: Marc De La Gueronniere <mdelagueronniere@verisign.com>
MFC after: 1 week
Sponsored by: Verisign, Inc.
many thanks for their continued support of FreeBSD.
While I'm there, also implement a new build knob, WITHOUT_HYPERV to
disable building and installing of the HyperV utilities when necessary.
The HyperV utilities are only built for i386 and amd64 targets.
This is a stable/10 candidate for inclusion with 10.1-RELEASE.
Submitted by: Wei Hu <weh microsoft com>
MFC after: 1 week
PCI IDs into quirks, which mostly fit (though you'd get no argument
from me that AHCI_Q_SATA1_UNIT0 is oddly specific). Set these quirks
in the PCI attachment. Make some shared functions public so that PCI
and possibly other bus attachments can use them.
The split isn't perfect yet, but it is functional. The split will be
perfected as other bus attachments for AHCI are written.
Sponsored by: Netflix
Reviewed by: kan, mav
Differential Revision: https://reviews.freebsd.org/D699
friendliness. This should restore old-fashioned kernel building in a
cross environment, though this has only had limited testing.
Sponsored by: Netflix
in the clocks=<...> properties of their FDT data. The clock properties
consist of 2-cell tuples, each containing a clock device node reference and
a clock number. A clock device driver can register itself as providing
this interface, then other drivers can turn the FDT clock node reference
into the corresponding device_t so that they can use the interface to query
and manipulate their clocks.
This provides convenience functions to enable or disable all the clocks
listed in the properties for a device, so most drivers will be able to
manage their clocks with a single call to fdt_clock_enable_all(dev).
This is the last major change in given branch.
Kernel changes:
* Use 64-bytes structures to hold multi-value variables.
* Use shared array to hold values from all tables (assume
each table algo is capable of holding 32-byte variables).
* Add some placeholders to support per-table value arrays in future.
* Use simple eventhandler-style API to ease the process of adding new
table items. Currently table addition may required multiple UH drops/
acquires which is quite tricky due to atomic table modificatio/swap
support, shared array resize, etc. Deal with it by calling special
notifier capable of rolling back state before actually performing
swap/resize operations. Original operation then restarts itself after
acquiring UH lock.
* Bump all objhash users default values to at least 64
* Fix custom hashing inside objhash.
Userland changes:
* Add support for dumping shared value array via "vlist" internal cmd.
* Some small print/fill_flags dixes to support u32 values.
* valtype is now bitmask of
<skipto|pipe|fib|nat|dscp|tag|divert|netgraph|limit|ipv4|ipv6>.
New values can hold distinct values for each of this types.
* Provide special "legacy" type which assumes all values are the same.
* More helpers/docs following..
Some examples:
3:41 [1] zfscurr0# ipfw table mimimi create valtype skipto,limit,ipv4,ipv6
3:41 [1] zfscurr0# ipfw table mimimi info
+++ table(mimimi), set(0) +++
kindex: 2, type: addr
references: 0, valtype: skipto,limit,ipv4,ipv6
algorithm: addr:radix
items: 0, size: 296
3:42 [1] zfscurr0# ipfw table mimimi add 10.0.0.5 3000,10,10.0.0.1,2a02:978:2::1
added: 10.0.0.5/32 3000,10,10.0.0.1,2a02:978:2::1
3:42 [1] zfscurr0# ipfw table mimimi list
+++ table(mimimi), set(0) +++
10.0.0.5/32 3000,0,10.0.0.1,2a02:978:2::1
- It was decided to change the driver name to if_ixl for FreeBSD
- This release adds the VF Driver to the tree, it can be built into
the kernel or as the if_ixlv module
- The VF driver is independent for the first time, this will be
desireable when full SRIOV capability is added to the OS.
- Thanks to my new coworker Eric Joyner for his superb work in
both the core and vf driver code.
Enjoy everyone!
Submitted by: jack.vogel@intel.com and eric.joyner@intel.com
MFC after: 3 days (hoping to make 10.1)
UNIX systems, eg. MacOS X and Solaris. It uses Sun-compatible map format,
has proper kernel support, and LDAP integration.
There are still a few outstanding problems; they will be fixed shortly.
Reviewed by: allanjude@, emaste@, kib@, wblock@ (earlier versions)
Phabric: D523
MFC after: 2 weeks
Relnotes: yes
Sponsored by: The FreeBSD Foundation
Mostly bugfixes or features developed in the past 6 months,
so this is a 10.1 candidate.
Basically no user API changes (some bugfixes in sys/net/netmap_user.h).
In detail:
1. netmap support for virtio-net, including in netmap mode.
Under bhyve and with a netmap backend [2] we reach over 1Mpps
with standard APIs (e.g. libpcap), and 5-8 Mpps in netmap mode.
2. (kernel) add support for multiple memory allocators, so we can
better partition physical and virtual interfaces giving access
to separate users. The most visible effect is one additional
argument to the various kernel functions to compute buffer
addresses. All netmap-supported drivers are affected, but changes
are mechanical and trivial
3. (kernel) simplify the prototype for *txsync() and *rxsync()
driver methods. All netmap drivers affected, changes mostly mechanical.
4. add support for netmap-monitor ports. Think of it as a mirroring
port on a physical switch: a netmap monitor port replicates traffic
present on the main port. Restrictions apply. Drive carefully.
5. if_lem.c: support for various paravirtualization features,
experimental and disabled by default.
Most of these are described in our ANCS'13 paper [1].
Paravirtualized support in netmap mode is new, and beats the
numbers in the paper by a large factor (under qemu-kvm,
we measured gues-host throughput up to 10-12 Mpps).
A lot of refactoring and additional documentation in the files
in sys/dev/netmap, but apart from #2 and #3 above, almost nothing
of this stuff is visible to other kernel parts.
Example programs in tools/tools/netmap have been updated with bugfixes
and to support more of the existing features.
This is meant to go into 10.1 so we plan an MFC before the Aug.22 deadline.
A lot of this code has been contributed by my colleagues at UNIPI,
including Giuseppe Lettieri, Vincenzo Maffione, Stefano Garzarella.
MFC after: 3 days.
cutover is, but we need better tools to cope with inline tuning per
compiler version than we have. This is a quick bandaid until such
tools are around.
socket options. This includes managing the correspoing stat counters.
Add the SCTP_DETAILED_STR_STATS kernel option to control per policy
counters on every stream. The default is off and only an aggregated
counter is available. This is sufficient for the RTCWeb usecase.
MFC after: 1 week
options into kern.opts.mk and change all the places where we use
src.opts.mk to pull in the options. Conditionally define SYSDIR and
use SYSDIR/conf/kern.opts.mk instead of a CURDIR path. Replace all
instances of CURDIR/../../etc with STSDIR, but only in the affected
files.
As a special compatibility hack, include bsd.owm.mk at the top of
kern.opts.mk to allow the bare build of sys/modules to work on older
systems. If the defaults ever change between 9.x, 10.x and current for
these options, however, you'll wind up with the host OS' defaults
rather than the -current defaults. This hack will be removed when
we no longer need to support this build scenario.
Reviewed by: jhb
Differential Revision: https://phabric.freebsd.org/D529
device attachment on arm platforms. If this is defined, nexus attaches
early in BUS_PASS_BUS, and other busses and devices attach later, in the
pass number they are set up for. Without it defined, nexus attaches in
BUS_PASS_DEFAULT and thus so does everything else, which is status quo.
Arm platforms which use FDT data to enumerate devices have been relying
on devices being attached in the exact order they're listed in the dts
source file. That's one of things currently preventing us from using
vendor-supplied fdt data (because then we don't control the order of the
devices in the data). Multi-pass attachment can go a long way towards
solving that problem by ensuring things like clock and interrupt drivers
are attached before the more mundane devices that need them.
The long-term goal is to have all arm fdt-based platforms using multipass.
This option is a bridge to that, letting us enable it selectively as
platforms are converted and tested (the alternative being to just throw
a big switch and try to fight fires as they're reported).
handled by creator(4) (Sun Creator 3D, Elite 3D, etc.). This provides
vt(4) consoles on all devices currently supported by syscons on sparc64.
The driver should also be easily adaptable to support newer Sun framebuffers
such as the XVR-500 and higher.
Many thanks to dumbbell@ (Jean-Sebastien Pedron) for testing this remotely
during development.
The MD allocators were very common, however there were some minor
differencies. These differencies were all consolidated in the MI allocator,
under ifdefs. The defines from machine/vmparam.h turn on features required
for a particular machine. For details look in the comment in sys/sf_buf.h.
As result no MD code left in sys/*/*/vm_machdep.c. Some arches still have
machine/sf_buf.h, which is usually quite small.
Tested by: glebius (i386), tuexen (arm32), kevlo (arm32)
Reviewed by: kib
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
opt_inet6.h into kmod.mk by forcing almost everybody to eat the same
dogfood. While at it, consolidate the opt_bpf.h and opt_mroute.h
targets here too.
provides support for a variety of low-end graphics hardware (SBus adapters,
Mach64, QEMU's framebuffer, XVR-100). A driver for at least the Creator3D
cards will have to be present before this can become the default console
driver.
To test vt(4) on sparc64, set kern.vty=vt at the loader prompt.
* Rewrite interface tables to use interface indexes
Kernel changes:
* Add generic interface tracking API:
- ipfw_iface_ref (must call unlocked, performs lazy init if needed, allocates
state & bumps ref)
- ipfw_iface_add_ntfy(UH_WLOCK+WLOCK, links comsumer & runs its callback to
update ifindex)
- ipfw_iface_del_ntfy(UH_WLOCK+WLOCK, unlinks consumer)
- ipfw_iface_unref(unlocked, drops reference)
Additionally, consumer callbacks are called in interface withdrawal/departure.
* Rewrite interface tables to use iface tracking API. Currently tables are
implemented the following way:
runtime data is stored as sorted array of {ifidx, val} for existing interfaces
full data is stored inside namedobj instance (chained hashed table).
* Add IP_FW_XIFLIST opcode to dump status of tracked interfaces
* Pass @chain ptr to most non-locked algorithm callbacks:
(prepare_add, prepare_del, flush_entry ..). This may be needed for better
interaction of given algorithm an other ipfw subsystems
* Add optional "change_ti" algorithm handler to permit updating of
cached table_info pointer (happens in case of table_max resize)
* Fix small bug in ipfw_list_tables()
* Add badd (insert into sorted array) and bdel (remove from sorted array) funcs
Userland changes:
* Add "iflist" cmd to print status of currently tracked interface
* Add stringnum_cmp for better interface/table names sorting
so it really should not be under "optional inet". The fact that uipc_accf.c
lives under kern/ lends some weight to making it a "standard" file.
Moving kern/uipc_accf.c from "optional inet" to "standard" eliminates the
need for #ifdef INET in kern/uipc_socket.c.
Also, this meant the net.inet.accf.unloadable sysctl needed to move, as
net.inet does not exist without networking compiled in (as it lives in
netinet/in_proto.c.) The new sysctl has been named net.accf.unloadable.
In order to support existing accept filter sysctls, the net.inet.accf node
has been added netinet/in_proto.c.
Submitted by: Steve Kiernan <stevek@juniper.net>
Obtained from: Juniper Networks, Inc.
completely silenced. Make sure these warnings appear again, so there is
some incentive to fix them, but do not error out the whole kernel build
for them.
Noticed by: steven@pyro.eu.org
PR: 191867
MFC after: 3 days
This allows to clone VMs and move them between LUNs inside one storage
host without generating extra network traffic to the initiator and back,
and without being limited by network bandwidth.
LUNs participating in copy operation should have UNIQUE NAA or EUI IDs set.
For LUNs without these IDs VMWare will use traditional copy operations.
Beware: the above LUN IDs explicitly set to values non-unique from the VM
cluster point of view may cause data corruption if wrong LUN is addressed!
MFC after: 2 weeks
Sponsored by: iXsystems, Inc.
This includes:
o All directories named *ia64*
o All files named *ia64*
o All ia64-specific code guarded by __ia64__
o All ia64-specific makefile logic
o Mention of ia64 in comments and documentation
This excludes:
o Everything under contrib/
o Everything under crypto/
o sys/xen/interface
o sys/sys/elf_common.h
Discussed at: BSDcan
console's ability to enter the debugger.... rwatson forgot to document
this when he changed it back in 2011... There is more docs to write
about this, but at least fix this for now...
Reviewed by: emaste
MFC after: 1 week
Both vt(4) and ofwfb(4) need a lot of love to be usable on sparc64 and even
then the performance of ofwfb(4) would suck compared to hardware accelerated
drivers like creator(4) and machfb(4).
into head. The code is not believed to have any effect
on the semantics of non-NFSv4.1 server behaviour.
It is a rather large merge, but I am hoping that there will
not be any regressions for the NFS server.
MFC after: 1 month
implement options TERMINAL_{KERN,NORM}_ATTR. These are aliased to
SC_{KERNEL_CONS,NORM}_ATTR and like these latter, allow to change the
default colors of normal and kernel text respectively.
Note on the naming: Although affecting the output of vt(4), technically
kern/subr_terminal.c is primarily concerned with changing default colors
so it would be inconsistent to term these options VT_{KERN,NORM}_ATTR.
Actually, if the architecture and abstraction of terminal+teken+vt would
be perfect, dev/vt/* wouldn't be touched by this commit at all.
Reviewed by: emaste
MFC after: 3 days
Sponsored by: Bally Wulff Games & Entertainment GmbH
configs. Switch the BERI_NETFPGA_MDROOT to 64bit by default.
Give we have working interrupts also cleanup the extra polling CFLAGS from
the module Makefile.
MFC after: 2 weeks
Introduce a Xen specific nexus that is going to be used by Xen PV/PVH
guests.
Sponsored by: Citrix Systems R&D
Approved by: gibbs
x86/xen/xen_nexus.c:
- Introduce a Nexus to use on Xen PV(H) guests, this prevents PV(H)
guests from using the legacy Nexus.
conf/files.amd64:
conf/files.i386:
- Add the xen nexus to the build.
Since there's no ACPI on PVH guests, we need to create a dummy CPU
device in order to fill the pcpu->pc_device field.
Sponsored by: Citrix Systems R&D
Approved by: gibbs
dev/xen/pvcpu/pvcpu.c:
- Create a dummy CPU device for PVH guests in order to fill the
per-cpu pc_device field.
conf/files:
- Add the pvcpu device to kernels using XEN or XENHVM options.
Create a dummy bus so top level Xen devices can attach to it (instead
of attaching directly to the nexus). This allows to have all the Xen
related devices grouped under a single bus.
Sponsored by: Citrix Systems R&D
Approved by: gibbs
x86/xen/xenpv.c:
- Attach the xenpv bus when running as a Xen guest.
- Attach the ISA bus if needed, in order to attach syscons.
conf/files.amd6:
conf/files.i386:
- Include the xenpv.c file in the build of i386/amd64 kernels using
XENHVM.
dev/xen/console/console.c:
dev/xen/timer/timer.c:
xen/xenstore/xenstore.c:
- Attach to the xenpv bus instead of the Nexus.
dev/xen/xenpci/xenpci.c:
- Xen specific devices on PVHVM guests are no longer attached to the
xenpci device, they are instead attached to the xenpv bus, remove
the now unused methods.
Create the necessary hooks in order to provide a Xen PV APIC
implementation that can be used on PVH. Most of the lapic ops
shouldn't be called on Xen, since we trap those operations at a higher
layer.
Sponsored by: Citrix Systems R&D
Approved by: gibbs
x86/xen/hvm.c:
x86/xen/xen_apic.c:
- Move IPI related code to xen_apic.c
x86/xen/xen_apic.c:
- Introduce Xen PV APIC implementation, most of the functions of the
lapic interface should never be called when running as PV(H) guest,
so make sure FreeBSD panics when trying to use one of those.
- Define the Xen APIC implementation in xen_apic_ops.
xen/xen_pv.h:
- Extern declaration of the xen_apic struct.
x86/xen/pv.c:
- Use xen_apic_ops as apic_ops when running as PVH guest.
conf/files.amd64:
conf/files.i386:
- Include the xen_apic.c file in the build of i386/amd64 kernels
using XENHVM.
Kernel-side changelog:
* Split general tables code and algorithm-specific table data.
Current algorithms (IPv4/IPv6 radix and interface tables radix) moved to
new ip_fw_table_algo.c file.
Tables code now supports any algorithm implementing the following callbacks:
+struct table_algo {
+ char name[64];
+ int idx;
+ ta_init *init;
+ ta_destroy *destroy;
+ table_lookup_t *lookup;
+ ta_prepare_add *prepare_add;
+ ta_prepare_del *prepare_del;
+ ta_add *add;
+ ta_del *del;
+ ta_flush_entry *flush_entry;
+ ta_foreach *foreach;
+ ta_dump_entry *dump_entry;
+ ta_dump_xentry *dump_xentry;
+};
* Change ->state, ->xstate, ->tabletype fields of ip_fw_chain to
->tablestate pointer (array of 32 bytes structures necessary for
runtime lookups (can be probably shrinked to 16 bytes later):
+struct table_info {
+ table_lookup_t *lookup; /* Lookup function */
+ void *state; /* Lookup radix/other structure */
+ void *xstate; /* eXtended state */
+ u_long data; /* Hints for given func */
+};
* Add count method for namedobj instance to ease size calculations
* Bump ip_fw3 buffer in ipfw_clt 128->256 bytes.
* Improve bitmask resizing on tables_max change.
* Remove table numbers checking from most places.
* Fix wrong nesting in ipfw_rewrite_table_uidx().
* Add IP_FW_OBJ_LIST opcode (list all objects of given type, currently
implemented for IPFW_OBJTYPE_TABLE).
* Add IP_FW_OBJ_LISTSIZE (get buffer size to hold IP_FW_OBJ_LIST data,
currenly implemented for IPFW_OBJTYPE_TABLE).
* Add IP_FW_OBJ_INFO (requests info for one object of given type).
Some name changes:
s/ipfw_xtable_tlv/ipfw_obj_tlv/ (no table specifics)
s/ipfw_xtable_ntlv/ipfw_obj_ntlv/ (no table specifics)
Userland changes:
* Add do_set3() cmd to ipfw2 to ease dealing with op3-embeded opcodes.
* Add/improve support for destroy/info cmds.
using a direct hook called from kern_vfs_bio_buffer_alloc().
Mark ffs_rawread.c as requiring both ffs and directio options to be
compiled into the kernel. Add ffs_rawread.c to the list of ufs.ko
module' sources.
In addition to stopping breaking the layering violation, it also
allows to link kernel when FFS is configured as module and DIRECTIO is
enabled.
One consequence of the change is that ffs_rawread.o is always linked
into the module regardless of the DIRECTIO option. This is similar to
the option QUOTA and ufs_quota.c.
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
- Update FDT file for BERI DE4 boards.
- Add needed kernel configuration keywords.
- Rename module to saf1761otg so that the device unit number does not
interfere with the hardware ID in dmesg.
Sponsored by: DARPA, AFRL
Netmap gets its own hardware-assisted virtual interface and won't take
over or disrupt the "normal" interface in any way. You can use both
simultaneously.
For kernels with DEV_NETMAP, cxgbe(4) carves out an ncxl<N> interface
(note the 'n' prefix) in the hardware to accompany each cxl<N>
interface. These two ifnet's per port share the same wire but really
are separate interfaces in the hardware and software. Each gets its own
L2 MAC addresses (unicast and multicast), MTU, checksum caps, etc. You
should run netmap on the 'n' interfaces only, that's what they are for.
With this, pkt-gen is able to transmit > 45Mpps out of a single 40G port
of a T580 card. 2 port tx is at ~56Mpps total (28M + 28M) as of now.
Single port receive is at 33Mpps but this is very much a work in
progress. I expect it to be closer to 40Mpps once done. In any case
the current effort can already saturate multiple 10G ports of a T5 card
at the smallest legal packet size. T4 gear is totally untested.
trantor:~# ./pkt-gen -i ncxl0 -f tx -D 00:07:43🆎cd:ef
881.952141 main [1621] interface is ncxl0
881.952250 extract_ip_range [275] range is 10.0.0.1:0 to 10.0.0.1:0
881.952253 extract_ip_range [275] range is 10.1.0.1:0 to 10.1.0.1:0
881.962540 main [1804] mapped 334980KB at 0x801dff000
Sending on netmap:ncxl0: 4 queues, 1 threads and 1 cpus.
10.0.0.1 -> 10.1.0.1 (00:00:00:00:00:00 -> 00:07:43🆎cd:ef)
881.962562 main [1882] Sending 512 packets every 0.000000000 s
881.962563 main [1884] Wait 2 secs for phy reset
884.088516 main [1886] Ready...
884.088535 nm_open [457] overriding ifname ncxl0 ringid 0x0 flags 0x1
884.088607 sender_body [996] start
884.093246 sender_body [1064] drop copy
885.090435 main_thread [1418] 45206353 pps (45289533 pkts in 1001840 usec)
886.091600 main_thread [1418] 45322792 pps (45375593 pkts in 1001165 usec)
887.092435 main_thread [1418] 45313992 pps (45351784 pkts in 1000834 usec)
888.094434 main_thread [1418] 45315765 pps (45406397 pkts in 1002000 usec)
889.095434 main_thread [1418] 45333218 pps (45378551 pkts in 1001000 usec)
890.097434 main_thread [1418] 45315247 pps (45405877 pkts in 1002000 usec)
891.099434 main_thread [1418] 45326515 pps (45417168 pkts in 1002000 usec)
892.101434 main_thread [1418] 45333039 pps (45423705 pkts in 1002000 usec)
893.103434 main_thread [1418] 45324105 pps (45414708 pkts in 1001999 usec)
894.105434 main_thread [1418] 45318042 pps (45408723 pkts in 1002001 usec)
895.106434 main_thread [1418] 45332430 pps (45377762 pkts in 1001000 usec)
896.107434 main_thread [1418] 45338072 pps (45383410 pkts in 1001000 usec)
...
Relnotes: Yes
Sponsored by: Chelsio Communications.
The CUSE library is a wrapper for the devfs kernel functionality which
is exposed through /dev/cuse . In order to function the CUSE kernel
code must either be enabled in the kernel configuration file or loaded
separately as a module. Currently none of the committed items are
connected to the default builds, except for installing the needed
header files. The CUSE code will be connected to the default world and
kernel builds in a follow-up commit.
The CUSE module was written by Hans Petter Selasky, somewhat inspired
by similar functionality found in FUSE. The CUSE library can be used
for many purposes. Currently CUSE is used when running Linux kernel
drivers in user-space, which need to create a character device node to
communicate with its applications. CUSE has full support for almost
all devfs functionality found in the kernel:
- kevents
- read
- write
- ioctl
- poll
- open
- close
- mmap
- private per file handle data
Requested by several people. Also see "multimedia/cuse4bsd-kmod" in
ports.
ismt(4) supports the SMBus Message Transport controller found on Intel
C2000 series (Avoton) and S1200 series (Briarwood) Atom SoCs.
Sponsored by: Intel
Intel 40G Ethernet Controller XL710 Family. This is
the core driver, a VF driver called i40evf, will be
following soon. Questions or comments to myself or
my co-developer Eric Joyner. Cheers!
src/sys and the rest of the tree for builds.
o eliminate including bsd.mkopts.mk for the moment in kern.opts.mk
o No need to include src.opts.mk at all anymore. The reasons for it
are now coverted in sys.mk and src.sys.mk.
platform code, it is expected these will be merged in the future when the
ARM code is more complete.
Until more boards can be tested only use this with the Raspberry Pi and
rrename the functions on the other SoCs.
Reviewed by: ian@
does an out-of-tree build without setting MAKESYSPATH) and recently
added requirements (JIRA's building the modules in a non-standard
layout). So, when MAKESYSPATH is defined, trust that it will do the
right thing (to catch the JIRA use case). When it isn't defined,
assume a standard FreeBSD tree and reach over to grab bsd.mkopt.mk (to
fix the /usr/ports use case). Both camps cannot be appeased otherwise,
so we have this kludge until it can be sorted out.
GENERIC64 for PowerPC to use vt with it.
Much to my chagrin, PS3 support seems to have bitrotted somewhat since the
last time I tried it. ehci panics on attach and interrupt handling seems
to be faulty. This should be fixed soon...
o KMODDEPS warning is 15 years stale. Remove it.
o MK_CTF will always be defined now, so no need to test to see if it
is defined.
o no need to define MK_FORMAT_EXTENTIONS if undefined anymore.
This driver supports the low and high precision models (9 and 11 bits) and
it will auto-detect the both variants.
The driver expose the temperature registers (actual temperature, shutdown
and hysteresys temperature) and also the configuration register.
It was tested on FDT systems: RPi, BBB and on non-FDT systems: AR71xx, with
both, hardware i2c controllers (when available) and gpioiic(4).
This provides a simple and cheap way for verifying the i2c bus on embedded
systems.
cards. LSI has been maintaining this driver outside of the FreeBSD
tree. It overlaps support of ThunderBolt and Invader cards that mfi(4)
supports. By default mfi(4) will attach to cards. If the tunable:
hw.mfi.mrsas_enable=1
is set then mfi(4) will not probe and attach to these newer cards and
allow mrsas(4) to attach. So by default this driver will not effect
a FreeBSD system unless mfi(4) is removed from the kernel or the
tunable is enabled.
mrsas(4) attaches disks to the CAM layer so it depends on CAM and devices
show up as /dev/daX. mfiutil(8) does not work with mrsas. The FreeBSD
version of MegaCli and StorCli from LSI do work with mrsas. It appears
that StorCli only works with mrsas. MegaCli appears to work with mfi(4)
and mrsas(4).
It would be good to add mfiutil(4) support to mrsas, emulations modes,
kernel logging, device aliases to ease the transition between mfi(4)
and mrsas(4).
Style issues should be resolved by LSI when they get committers approved.
The plan is get this driver in FreeBSD 9.3 to improve HW support.
Thanks to LSI for developing, testing and working with FreeBSD to
make this driver co-exist in FreeBSD. This improves the overall
support of MegaRAID SAS.
Submitted by: Kashyap Desai <Kashyap.Desai@lsi.com>
Reviewed by: scottl
MFC after: 3 days
Sponsored by: LSI
This is derived from the mps(4) driver, but it supports only the 12Gb
IT and IR hardware including the SAS 3004, SAS 3008 and SAS 3108.
Some notes about this driver:
o The 12Gb hardware can do "FastPath" I/O, and that capability is included in
this driver.
o WarpDrive functionality has been removed, since it isn't supported in
the 12Gb driver interface.
o The Scatter/Gather list handling code is significantly different between
the 6Gb and 12Gb hardware. The 12Gb boards support IEEE Scatter/Gather
lists.
Thanks to LSI for developing and testing this driver for FreeBSD.
share/man/man4/mpr.4:
mpr(4) man page.
sys/dev/mpr/*:
mpr(4) driver files.
sys/modules/Makefile,
sys/modules/mpr/Makefile:
Add a module Makefile for the mpr(4) driver.
sys/conf/files:
Add the mpr(4) driver.
sys/amd64/conf/GENERIC,
sys/i386/conf/GENERIC,
sys/mips/conf/OCTEON1,
sys/sparc64/conf/GENERIC:
Add the mpr(4) driver to all config files that currently
have the mps(4) driver.
sys/ia64/conf/GENERIC:
Add the mps(4) and mpr(4) drivers to the ia64 GENERIC
config file.
sys/i386/conf/XEN:
Exclude the mpr module from building here.
Submitted by: Steve McConnell <Stephen.McConnell@lsi.com>
MFC after: 3 days
Tested by: Chris Reeves <chrisr@spectralogic.com>
Sponsored by: LSI, Spectra Logic
Relnotes: LSI 12Gb SAS driver mpr(4) added
lindev(4) was only used to provide /dev/full which is now a standard feature of
FreeBSD. /dev/full was never linux-specific and provides a generally useful
feature.
Document this in UPDATING and bump __FreeBSD_version. This will be documented
in the PH shortly.
Reported by: jkim
kernel config file. If you also want to have a static DTB compiled
into your kernel, however, it cannot be a list. We have no mechanism
in the kernel for picking one, so that doesn't make sense and will
result in a compile-time error.
binmisc code to be build on amd64/i386 for the kernel.
Update NOTES with some indication of what this code is used for.
Pointed out by jhb@ ... thanks!
Submitted by: jhb@
execution to a emumation program via parsing of ELF header information.
With this kernel module and userland tool, poudriere is able to build
ports packages via the QEMU userland tools (or another emulator program)
in a different architecture chroot, e.g. TARGET=mips TARGET_ARCH=mips
I'm not connecting this to GENERIC for obvious reasons, but this should
allow the kernel module to be built by default and enable the building
of the userland tool (which automatically loads the kernel module).
Submitted by: sson@
Reviewed by: jhb@
systems need fine-grained control over what's in and what's out.
That's ideal. For now, separate GPT labels from the rest and allow
g_label to be built with just GPT labels.
Obtained from: Juniper Networks, Inc.
