Commit Graph

19 Commits

Author SHA1 Message Date
Marius Strobl
9888f86a16 - Factor out the common and generic parts of the sparc64 host-PCI-bridge
drivers into the revived sys/sparc64/pci/ofw_pci.c, previously already
  serving a similar purpose. This has been done with sun4v in mind, which
  explains a) the otherwise not that obvious scheme employed and b) why
  reusing sys/powerpc/ofw/ofw_pci.c was even lesser an option.
- Add a workaround for QEMU once again not emulating real machines, in
  this case by not providing the OFW_PCI_CS_MEM64 range. [1]

Submitted by:	jhb [1]
MFC after:	1 week
2015-09-12 22:49:32 +00:00
Marius Strobl
b09c4bd47a - Merge the *_SET macros from fire(4) which generally print out the
register changes when compiled with SCHIZO_DEBUG and take advantage
  of them.
- Add support for the XMITS Fireplane/Safari to PCI-X bridges. I tought
  I'd need this for a Sun Fire 3800, which then turned out to not being
  equipped with such a bridge though. The support for these should be
  complete but given that it hasn't actually been tested probing is
  disabled for now.
  This required a way to alter the XMITS configuration in case a PCI-X
  device is found further down the device tree so the sparc64 specific
  ofw_pci kobj was revived with a ofw_pci_setup_device method, which is
  called by the ofw_pcibus code for every device added.
- A closer inspection of the OpenSolaris code indicates that consistent
  DMA flushing/syncing as well as the block store workaround should be
  applied with every BUS_DMASYNC_POSTREAD instead of in a wrapper around
  interrupt handlers for devices behind PCI-PCI bridges only as suggested
  by the documentation (code for the latter actually exists in OpenSolaris
  but is disabled by default), which also makes more sense.
- Add a workaround for Casinni/Skyhawk combinations. Chances are that
  this solves the crashes seen when using the the on-board Casinni NICs
  of Sun Fire V480 equipped with centerplanes other than 501-6780 or
  501-6790. This also takes advantage of the ofw_pci_setup_device method.
- Mark some unused parameters as such.
2011-03-26 16:49:12 +00:00
Marius Strobl
273fb3dc7c Sync licenses and the corresponding RCS IDs with NetBSD, mainly switching
the licenses of Matthew R. Green and the TNF to 2-clause.

Obtained from:	NetBSD
2011-03-12 14:33:32 +00:00
Marius Strobl
36fd650f09 Add structures for OFW MSI/MSI-X support. These are identical for
both sun4u and sun4v.
2009-12-23 21:07:49 +00:00
Marius Strobl
7b8253c3eb Factor out the duplicated macro for the device type used in the
OFW device tree for PCI bridges and add a new one for PCI Express.
While at it, take advantage of the former for the rman(9) work-
around in jbusppm(4).
2009-09-13 14:47:31 +00:00
Nathan Whitehorn
94b4a038a1 Adapt parts of the sparc64 Open Firmware bus enumeration code (in particular,
the code for parsing interrupt maps) to PowerPC and reflect their new MI
status by moving them to the shared dev/ofw directory.

This commit also modifies the OFW PCI enumeration procedure on PowerPC to
allow the bus to find non-firmware-enumerated devices that Apple likes to add,
and adds some useful Open Firmware properties (compat and name) to the pnpinfo
string of children on OFW SBus, EBus, PCI, and MacIO links. Because of the
change to PCI enumeration on PowerPC, X has started working again on PPC
machines with Grackle hostbridges.

Reviewed by:	marius
Obtained from:	sparc64
2008-12-15 15:31:10 +00:00
Marius Strobl
898112a7dc cosmetic changes and style fixes 2008-08-22 20:28:19 +00:00
Marius Strobl
b7ee09f7b0 Remove the MD isa_irq_pending() and the underlying PCI-specific
infrastructure. Its only consumer ever was sio(4) and thus was
unused on sparc64 since removing the last traces of sio(4) in
sparc64 configuration files in favor for uart(4) over three
years ago. If similar functionality is required again it should
be brought back as an MD intr_pending() which works for all
busses by using for example interrupt controller hooks.
2008-04-26 11:01:38 +00:00
Marius Strobl
f0d8df7bb2 - Move ofw_pci_alloc_busno() to the ofw_pci KOBJ interface,
allowing the driver for the host-PCI-bridge to indicate that
  reenumeration of the PCI busses isn't supported by returning
  -1 instead of a valid PCI bus number. This is needed in order
  support both Tomatillo, which don't support reenumeration and
  thus are apparently intended to be used for independently
  numbered PCI domains only, and Psycho bridges, whose busses
  need to be reenumerated on at least some E450, without the
  #ifndef currently used for sun4v in order to support multiple
  independently PCI domains. The actual allocation/incrementation
  of the PCI bus numbers is now done in psycho(4), though it
  no longer establish a mapping between bus numbers and device
  nodes like ofw_pci_alloc_busno() did as that functionality
  wasn't used (but can easily brought back if really needed).
  The now no longer used sys/sparc64/pci/ofw_pci.c is also
  removed from sys/conf/files.sun4v as ofw_pci_alloc_busno()
  wasn't used there in the first place.
- In ofw_pci_default_{adjust_busrange,intr_pending}() sanity
  check that the device has a parent before passing it on.
- Make psycho_softcs static to sys/sparc64/pci/psycho.c as
  it's not used outside of that module.
- In sys/sparc64/pci/ofw_pcib_subr.c remove the superfluous
  inclusion of opt_global.h and correct the debug output for
  adjusting the subordinate bus number.
2007-06-18 21:49:42 +00:00
Marius Strobl
58299dd09e - Move the declaration of struct upa_ranges and the UPA_RANGE_* macros
from sys/sparc64/include/ofw_upa.h to sys/sparc64/pci/ofw_pci.h and
  rename them to struct ofw_pci_ranges and OFW_PCI_RANGE_* respectively.
  This ranges struct only applies to host-PCI bridges but no to other
  bridges found on UPA. At the same time it applies to all host-PCI
  bridges regardless of whether the interconnection bus is Fireplane/
  Safari, JBus or UPA.
- While here rename the PCI_CS_* macros in sys/sparc64/pci/ofw_pci.h
  to OFW_PCI_CS_* in order to be consistent and change this header to
  use uintXX_t instead of u_intXX_t.
2005-12-03 19:52:20 +00:00
Warner Losh
60727d8b86 /* -> /*- for license, minor formatting changes 2005-01-07 02:29:27 +00:00
Marius Strobl
26280d88d7 - Introduce an ofw_bus kobj-interface for retrieving the OFW node and a
subset ("compatible", "device_type", "model" and "name") of the standard
  properties in drivers for devices on Open Firmware supported busses. The
  standard properties "reg", "interrupts" und "address" are not covered by
  this interface because they are only of interest in the respective bridge
  code. There's a remaining standard property "status" which is unclear how
  to support properly but which also isn't used in FreeBSD at present.
  This ofw_bus kobj-interface allows to replace the various (ebus_get_node(),
  ofw_pci_get_node(), etc.) and partially inconsistent (central_get_type()
  vs. sbus_get_device_type(), etc.) existing IVAR ones with a common one.
  This in turn allows to simplify and remove code-duplication in drivers for
  devices that can hang off of more than one OFW supported bus.
- Convert the sparc64 Central, EBus, FHC, PCI and SBus bus drivers and the
  drivers for their children to use the ofw_bus kobj-interface. The IVAR-
  interfaces of the Central, EBus and FHC are entirely replaced by this. The
  PCI bus driver used its own kobj-interface and now also uses the ofw_bus
  one. The IVARs special to the SBus, e.g. for retrieving the burst size,
  remain.
  Beware: this causes an ABI-breakage for modules of drivers which used the
  IVAR-interfaces, i.e. esp(4), hme(4), isp(4) and uart(4), which need to be
  recompiled.
  The style-inconsistencies introduced in some of the bus drivers will be
  fixed by tmm@ in a generic clean-up of the respective drivers later (he
  requested to add the changes in the "new" style).
- Convert the powerpc MacIO bus driver and the drivers for its children to
  use the ofw_bus kobj-interface. This invloves removing the IVARs related
  to the "reg" property which were unused and a leftover from the NetBSD
  origini of the code. There's no ABI-breakage caused by this because none
  of these driver are currently built as modules.
  There are other powerpc bus drivers which can be converted to the ofw_bus
  kobj-interface, e.g. the PCI bus driver, which should be done together
  with converting powerpc to use the OFW PCI code from sparc64.
- Make the SBus and FHC front-end of zs(4) and the sparc64 eeprom(4) take
  advantage of the ofw_bus kobj-interface and simplify them a bit.

Reviewed by:	grehan, tmm
Approved by:	re (scottl)
Discussed with:	tmm
Tested with:	Sun AX1105, AXe, Ultra 2, Ultra 60; PPC cross-build on i386
2004-08-12 17:41:33 +00:00
Marius Strobl
66a79ac95d - Remove the old sparc64 OFW PCI code (as opposed to the former
"options OFW_NEWPCI").
  This is a bit overdue, the new sparc64 OFW PCI code which is
  meant to replace the old one is in place for 10 months and
  enabled by default in GENERIC for 8 months. FreeBSD 5.2 and
  5.2.1 also shipped with the new code enabled by default.
- Some minor clean-up, e.g. remove functions that encapsulated
  the #ifdefs for OFW_NEWPCI, remove unused resp. no longer
  required includes, etc.

Approved by:	tmm, no objections on freebsd-sparc64
2004-05-08 13:53:47 +00:00
Thomas Moestl
1d80cb1b37 Add the new sparc64 OFW PCI framework, conditional on options OFW_NEWPCI
for now. It introduces a OFW PCI bus driver and a generic OFW PCI-PCI
bridge driver. By utilizing these, the PCI handling is much more elegant
now.

The advantages of the new approach are:
- Device enumeration should hopefully be more like on Solaris now,
  so unit numbers should match what's printed on the box more
  closely.
- Real interrupt routing is implemented now, so cardbus bridges
  etc. have at least a chance to work.
- The quirk tables are gone and have been replaced by (hopefully
  sufficient) heuristics.
- Much cleaner code.

There was also a report that previously bogus interrupt assignments
are fixed now, which can be attributed to the new heuristics.

A pitfall, and the reason why this is not the default yet, is that
it changes device enumeration, as mentioned above, which can make
it necessary to change the system configuration if more than one
unit of a device type is present (on a system with two hme cars,
for example, it is possible that hme0 becomes hme1 and vice versa
after enabling the option). Systems with multiple disk controllers
may need to be booted into single user (and require manual specification
of the root file system on boot) to adjust the fstab.
Nevertheless, I would like to encourage users to use this option,
so that it can be made the default soon.

In detail, the changes are:
- Introduce an OFW PCI bus driver; it inherits most methods from the
  generic PCI bus driver, but uses the firmware for enumeration,
  performs additional initialization for devices and firmware-specific
  interrupt routing. It also implements an OFW-specific method to allow
  child devices to get their firmware nodes.
- Introduce an OFW PCI-PCI bridge driver; again, it inherits most
  of the generic PCI-PCI bridge driver; it has it's own method for
  interrupt routing, as well as some sparc64-specific methods (one to
  get the node again, and one to adjust the bridge bus range, since
  we need to reenumerate all PCI buses).
- Convert the apb driver to the new way of handling things.
- Provide a common framework for OFW bridge drivers, used be the two
  drivers above.
- Provide a small common framework for interrupt routing (for all
  bridge types).
- Convert the psycho driver to the new framework; this gets rid of a
  bunch of old kludges in pci_read_config(), and the whole
  preinitialization  (ofw_pci_init()).
- Convert the ISA MD part and the EBus driver to the new way
  interrupts and nodes are handled.
- Introduce types for firmware interrupt properties.
- Rename the old sparcbus_if to ofw_pci_if by repo copy (it is only
  required for PCI), and move it to a more correct location (new
  support methodsx were also added, and an old one was deprecated).
- Fix a bunch of minor bugs, perform some cleanups.

In some cases, I introduced some minor code duplication to keep the
new code clean, in hopes that the old code will be unifdef'ed soon.

Reviewed in part by:	imp
Tested by:	jake, Marius Strobl <marius@alchemy.franken.de>,
		Sergey Mokryshev <mokr@mokr.net>,
		Chris Jackman <cjackNOSPAM@klatsch.org>
Info on u30 firmware provided by:	kris
2003-07-01 14:52:47 +00:00
Thomas Moestl
c944338750 Fix interrupt assignment for non-builtin PCI devices on e450s.
This machine uses a non-standard scheme to specify the interrupts to
be assigned for devices in PCI slots; instead of giving the INO
or full interrupt number (which is done for the other devices in this
box), the firmware interrupt properties contain intpin numbers, which
have to be swizzled as usual on PCI-PCI bridges; however, the PCI host
bridge nodes have no interrupt map, so we need to guess the
correct INO by slot number of the device or the closest PCI-PCI
bridge leading to it, and the intpin.

To do this, this fix makes the following changes:
- Add a newbus method for sparc64 PCI host bridges to guess
  the INO, and glue code in ofw_pci_orb_callback() to invoke it based
  on a new quirk entry. The guessing is only done for interrupt numbers
  too low to contain any IGN found on e450s.
- Create another new quirk entry was created to prevent mapping of EBus
  interrupts  at PCI level; the e450 has full INOs in the interrupt
  properties of EBus devices, so trying to remap them could cause
  problems.
- Set both quirk entries for e450s; remove the no-swizzle entry.
- Determine the psycho half (bus A or B) a driver instance manages
  in psycho_attach()
- Implement the new guessing method for psycho, using the slot number,
  psycho half and property value (intpin).

Thanks go to the testers, especially Brian Denehy, who tested many kernels
for me until I had found the right workaround.

Tested by:	Brian Denehy <B.Denehy@90east.com>, jake, fenner,
		Marius Strobl <marius@alchemy.franken.de>,
		Marian Dobre <mari@onix.ro>
Approved by:	re (scottl)
2003-05-30 20:48:05 +00:00
Thomas Moestl
8c8a1169df Add two new workaround for firmware anomalies:
1. At least some Netra t1 models have PCI buses with no associated
   interrupt map, but obviously expect the PCI swizzle to be done with
   the interrupt number from the higher level as intpin. In this case,
   the mapping also needs to continue at parent bus nodes.
   To handle that, add a quirk table based on the "name" property of
   the root node to avoid breaking other boxen. This property is now
   retrieved and printed at boot.
2. On SPARCengine Ultra AX machines, interrupt numbers are not mapped
   at all, and full interrupt numbers (not just INOs) are given in
   the interrupt properties. This is more or less cosmetical; the
   PCI interrupt numbers would be wrong, but the psycho resource
   allocation method would pass the right numbers on anyway.

Tested by:	mux (1), Maxim Mazurok <maxim@km.ua> (2)
2002-11-07 16:07:46 +00:00
Thomas Moestl
5fb49f9fd6 Add PCI bus enumeration and latency timer setup to the sparc64 MD PCI
code. Both tasks are not always performed completely by the firmware.
The former is required to get some e450 models to boot; the latter fixes
the repeated fifo underruns with hme(4)s and gem(4)s observed on some
machines (and probably performance problems with other peripherals as
well).
2002-06-12 19:20:57 +00:00
Thomas Moestl
464ae30ee6 Make the OpenFirmware interrupt mapping code more generic, to reduce
the bus-dependent code and to be able to support more systems. The core
of the new code is mostly obtained from NetBSD.
Kluge the interrupt routing methods of the psycho and apb drivers so
that an intline of 0 can be handled for now; real routing is still not
possible (all intline registers are preinitialized instead); this will
require a sparc64-specific adaption of the driver for generic PCI-PCI
bridges with a custom routing method to work right.
2002-03-24 02:11:06 +00:00
Thomas Moestl
9d69e46260 Add support for the Sun psycho/sabre UPA-PCI bridge, some OpenFirmware
PCI support code, and a driver for the Sun APB PCI-PCI bridge.
Partly ported from NetBSD.
2001-11-09 20:19:58 +00:00