Small summary
-------------
o Almost all IPsec releated code was moved into sys/netipsec.
o New kernel modules added: ipsec.ko and tcpmd5.ko. New kernel
option IPSEC_SUPPORT added. It enables support for loading
and unloading of ipsec.ko and tcpmd5.ko kernel modules.
o IPSEC_NAT_T option was removed. Now NAT-T support is enabled by
default. The UDP_ENCAP_ESPINUDP_NON_IKE encapsulation type
support was removed. Added TCP/UDP checksum handling for
inbound packets that were decapsulated by transport mode SAs.
setkey(8) modified to show run-time NAT-T configuration of SA.
o New network pseudo interface if_ipsec(4) added. For now it is
build as part of ipsec.ko module (or with IPSEC kernel).
It implements IPsec virtual tunnels to create route-based VPNs.
o The network stack now invokes IPsec functions using special
methods. The only one header file <netipsec/ipsec_support.h>
should be included to declare all the needed things to work
with IPsec.
o All IPsec protocols handlers (ESP/AH/IPCOMP protosw) were removed.
Now these protocols are handled directly via IPsec methods.
o TCP_SIGNATURE support was reworked to be more close to RFC.
o PF_KEY SADB was reworked:
- now all security associations stored in the single SPI namespace,
and all SAs MUST have unique SPI.
- several hash tables added to speed up lookups in SADB.
- SADB now uses rmlock to protect access, and concurrent threads
can do SA lookups in the same time.
- many PF_KEY message handlers were reworked to reflect changes
in SADB.
- SADB_UPDATE message was extended to support new PF_KEY headers:
SADB_X_EXT_NEW_ADDRESS_SRC and SADB_X_EXT_NEW_ADDRESS_DST. They
can be used by IKE daemon to change SA addresses.
o ipsecrequest and secpolicy structures were cardinally changed to
avoid locking protection for ipsecrequest. Now we support
only limited number (4) of bundled SAs, but they are supported
for both INET and INET6.
o INPCB security policy cache was introduced. Each PCB now caches
used security policies to avoid SP lookup for each packet.
o For inbound security policies added the mode, when the kernel does
check for full history of applied IPsec transforms.
o References counting rules for security policies and security
associations were changed. The proper SA locking added into xform
code.
o xform code was also changed. Now it is possible to unregister xforms.
tdb_xxx structures were changed and renamed to reflect changes in
SADB/SPDB, and changed rules for locking and refcounting.
Reviewed by: gnn, wblock
Obtained from: Yandex LLC
Relnotes: yes
Sponsored by: Yandex LLC
Differential Revision: https://reviews.freebsd.org/D9352
By default reading the diagnostic counters is disabled. The firmware
decides which counters are supported and only those supported show up
in the dev.mce.X.diagnostics sysctl tree.
To enable reading of diagnostic counters set one or more of the
following sysctls to one:
dev.mce.X.conf.diag_general_enable=1
dev.mce.X.conf.diag_pci_enable=1
MFC after: 1 week
Sponsored by: Mellanox Technologies
This patch adds driver for temperature/humidity sensor connected via GPIO.
To compile it into kernel add "device gpioths". To activate driver, use
hints (.at and .pins) for gpiobus. As result it will provide temperature &
humidity values via sysctl.
DHT11 is cheap & popular temperature/humidity sensor used via GPIO on ARM
or MIPS devices like Raspberry Pi or Onion Omega.
Reviewed by: adrian
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D9185
- em(4) igb(4) and lem(4)
- deprecate the igb device from kernel configurations
- create a symbolic link in /boot/kernel from if_em.ko to if_igb.ko
Devices tested:
- 82574L
- I218-LM
- 82546GB
- 82579LM
- I350
- I217
Please report problems to freebsd-net@freebsd.org
Partial review from jhb and suggestions on how to *not* brick folks who
originally would have lost their igbX device.
Submitted by: mmacy@nextbsd.org
MFC after: 2 weeks
Relnotes: yes
Sponsored by: Limelight Networks and Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D8299
card presence and write protect switch detection.
A bridge driver just needs to call the setup routine in its attach(), the
teardown in its detach(), and write a couple tiny glue functions to connect
the sdhci interface functions to the new helper functions. This is not
extensively documented, but multiple examples will exist real soon.
all public firmwares for all chips since the last release (1.15.37.0)
follows (it's a straight copy-paste from the Release Notes for the
12/30/2016 Unified Wire release on Chelsio's website).
T6 Firmware
++++++++++++
Version : 1.16.26.0
Date : 12/28/2016
Fixes
-----
BASE:
- Max number of egress and control queues adjusted to accomodate
co-processor mode queues.
- Fixed intermittent DDR3/4 ECC errors.
- Fixed a traffic stall when ETS BW is configured as 0%.
- Max number of ethctrl queue in VF set to 1.
ETH:
- Added a new config file option 'speed' under port section to set the
port speed. Use only when auto negotiation is off.
- FEC option removed from firmware config file. cxgbtool can be used to
change the fec setting.
- CPL_TX_TNL_LSO cpl handling added in ETH_TX_PKT_VM handler. This fixes
large tunnel tcp packet support for VxLAN.
Version : 1.16.22.0
Date : 12/05/2016
Fixes
-----
BASE:
- fw_port_type updated in fw API to match kernel.org definitions.
- Saved power by disaling unused MAC lanes.
- Configures correct power bin.
- Enhanced DDR4 performance.
- Enabled interrupts.
- Fixed an issue where filter rule for 'unicast hash' is not working.
ETH:
- Disabled auto negotiation by default because most of 100G switches do
not support AN as of today.
- Fixed flow control not getting disabled problem.
- Fixed an issue where port0 doesn't come up sometimes.
- Fixed 10G link not coming up issue.
- Fixed an issue with promiscuous mode when dcbx disabled.
OFLD:
- Fixed a connection stuck issue when abort is received during out of tx
pages backpressure.
ENHANCEMENTS
------------
BASE:
- Added inline TLS mode support.
Version : 1.16.12.0
Date : 11/11/2016
ENHANCEMENTS
------------
BASE:
- Added T6 support.
- Added T6 1G/10G/25G/40G/100G link speeds.
- Added T6 co-processor mode crypto support.
- Added facility to increase link AN+AEC timeout.
OFLD:
- Added support for all T5 offload protocols except FCoE.
iSCSI:
- iscsi completion moderation enabled.
=======================================================================
T5 Firmware
++++++++++++
Version : 1.16.26.0
Date : 12/28/2016
FIXES
-----
BASE:
- Max number of ethctrl queue in VF set to 1.
Version : 1.16.22.0
Date : 12/05/2016
FIXES
-----
BASE:
- Fixed an issue where filter rule for 'unicast hash' is not working.
ETH:
- Fixed an issue with promiscuous mode when dcbx disabled.
ENHANCEMENTS
------------
ETH:
- Added 40G-KR support.
Version : 1.16.12.0
Date : 11/11/2016
FIXES
-----
BASE:
- Fixed multiple issues related with VFs FLR processing.
- Fixed channel assignment based on number of ports in adapter.
- Fixed a crash when VM having PF assigned as passthrough mode is
rebooted.
- Handled 2nd HELLO command from the same PF without seeing BYE from the
same PF and if that is the only PF.
- A warning is printed in firmware log if PCI-E cookie generation is
enabled in serial initialization file.
- Fixed multiple issues related with Filtering.
- Enabled DSGL memory write for iscsi and rdma.
- Added new FW_PARAMS_CMD[DEV] options to retrieve Serial Configuration
and VPD version numbers.
- Fixed an issue where LVDS output was not getting enabled using vpd.
DCBX:
- Fixed DCBX CEE Incorrect class to pririty mapping.
- Fixed incorrect interpretation of DCBX IEEE PFC.
ETH:
- Adjusted the link related delay timings according to the QSFP spec.
- Improved 40G link bringup time with few switches.
OFLD:
- Do not reserve qp/cq if rdma capability is not enabled.
- Fixed an issue where approx 1600+ TOE connections were causing a
firmware fatal error.
FOiSCSI:
- Fixed an issue where unloading foiscsi driver causes mailbox timeout.
ENHANCEMENTS
------------
BASE:
- Added 10G KR/KX support.
- Added T540-BT adapter support.
- Added 4 new rss key modes for PFs and VFs.
OFLD:
- Added new WR FW_RI_FR_NSMR_TPTE_WR to improve fast MR write
performance in RDMA.
Version : 1.16.5.0
Date : 10/26/2016
FIXES
-----
BASE:
- Fixed multiple issues where FLR from multiple VFs can cause firmware
crash.
- Fixed channel assignment based on number of ports in adapter.
- Fixed the HELLO command master force api to handle the 2nd HELLO
correctly without getting BYE from the PF driver.
- Added facility to retrieve Serial configuration and VPD version. Two
new FW_PARAMS_CMD[DEV] options added to retrieve these values.
- Fixed multiple issues where FLR from multiple VFs are not completing.
- Added new RSS hash secret key modes.
- Fixed an issue where LVDS output was not getting enabled using vpd.
DCBX:
- Fixed an issue where iscsi tlv is sent incorrectly to host (DCBX CEE).
- Fixed an issue where app priority values are not handled correctly
in fw (DCBX IEEE).
ETH:
- Adjusts the link related delay timings according to the QSFP spec.
- Changed 2.5G mac speed bit to 25G mac speed bit in fw API.
- Improvement in 40G link bringup time with few switches.
OFLD:
- Do not reserve qp/cq if rdma capability is not enabled.
- Fixed an issue where approx 1600+ TOE connections were causing a
firmware fatal error.
- Fixed DSGL memory write in T5. Now iwarp and iscsi can use DSGL to do
memory write.
- Fixed multiple issues in hash filter mode where incorrect protocol
mask was getting used and affecting hash filter functionality.
- New fastpath WR FW_RI_FR_NSMR_TPTE_WR (with fully populated TPTE) is
added for small REG_MR operations.
FOiSCSI:
- Fixed an issue in foiscsi recovery path.
- Fixed an issue where foiscsi (in VM in PCIE passthrough mode) didn't
come up after VM FLR.
ENHANCEMENTS
------------
ETH:
- Implemented 1G/10G KR/KX ability.
- Implemented T540-BT adapter support.
=======================================================================
T4 Firmware
+++++++++++
Version : 1.16.12.0
Date : 11/11/2016
FIXES
-----
BASE:
- Fixed an issue where reading temperature sesors using ldst command
causes mailbox timeout.
- Added new FW_PARAMS_CMD[DEV] options to retrieve Serial Configuration
and VPD version numbers.
ETH:
- Fixed DCBX CEE Incorrect class to pririty mapping.
FOiSCSI:
- Fixed an issue where unloading foiscsi driver causes mailbox timeout.
MFC after: 3 days
Sponsored by: Chelsio Communications
Add ACPI part for ig4 driver to make it work on Intel BayTrail SoC where
ig4 device is available only through ACPI
Reviewed by: avg
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D8742
This adds support for:
- Serializing an bhnd_nvram_plist (as exported from bhnd_nvram_store, etc) to
an arbitrary NVRAM data format.
- Generating a serialized representation of the current NVRAM store's state
suitable for writing back to flash, or re-encoding for upload to a
FullMAC device.
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D8762
Implements bhnd_nvram_store support for parsing and operating over NVRAM
device paths, and device path aliases, as well as tracking per-path NVRAM
variable writes.
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D8760
This adds support for bhnd_nvram_val_convert_init() and
bhnd_nvram_val_convert_new(), which may be used to perform value
format-aware encoding of an NVRAM value to a new target format/type.
This will be used to simplify converting to/from serialized
format-specific NVRAM value representations to common external
representations.
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D8757
representing arbitrary Broadcom NVRAM key/value pairs.
This will be used to track pending changes in bhnd_nvram_store, and
provide support for exporting all or a device subpath for NVRAM (as
required by some fullmac wifi chipsets).
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D8756
for IPv6.
It gets performance benefits from reduced number of checks. It doesn't
copy mbuf to be able send ICMPv6 error message, because it keeps mbuf
unchanged until the moment, when the route decision has been made.
It doesn't do IPsec checks, and when some IPsec security policies present,
ip6_input() uses normal slow path.
Reviewed by: bz, gnn
Obtained from: Yandex LLC
MFC after: 1 month
Sponsored by: Yandex LLC
Differential Revision: https://reviews.freebsd.org/D8527
Changes include modifications in kernel crash dump routines, dumpon(8) and
savecore(8). A new tool called decryptcore(8) was added.
A new DIOCSKERNELDUMP I/O control was added to send a kernel crash dump
configuration in the diocskerneldump_arg structure to the kernel.
The old DIOCSKERNELDUMP I/O control was renamed to DIOCSKERNELDUMP_FREEBSD11 for
backward ABI compatibility.
dumpon(8) generates an one-time random symmetric key and encrypts it using
an RSA public key in capability mode. Currently only AES-256-CBC is supported
but EKCD was designed to implement support for other algorithms in the future.
The public key is chosen using the -k flag. The dumpon rc(8) script can do this
automatically during startup using the dumppubkey rc.conf(5) variable. Once the
keys are calculated dumpon sends them to the kernel via DIOCSKERNELDUMP I/O
control.
When the kernel receives the DIOCSKERNELDUMP I/O control it generates a random
IV and sets up the key schedule for the specified algorithm. Each time the
kernel tries to write a crash dump to the dump device, the IV is replaced by
a SHA-256 hash of the previous value. This is intended to make a possible
differential cryptanalysis harder since it is possible to write multiple crash
dumps without reboot by repeating the following commands:
# sysctl debug.kdb.enter=1
db> call doadump(0)
db> continue
# savecore
A kernel dump key consists of an algorithm identifier, an IV and an encrypted
symmetric key. The kernel dump key size is included in a kernel dump header.
The size is an unsigned 32-bit integer and it is aligned to a block size.
The header structure has 512 bytes to match the block size so it was required to
make a panic string 4 bytes shorter to add a new field to the header structure.
If the kernel dump key size in the header is nonzero it is assumed that the
kernel dump key is placed after the first header on the dump device and the core
dump is encrypted.
Separate functions were implemented to write the kernel dump header and the
kernel dump key as they need to be unencrypted. The dump_write function encrypts
data if the kernel was compiled with the EKCD option. Encrypted kernel textdumps
are not supported due to the way they are constructed which makes it impossible
to use the CBC mode for encryption. It should be also noted that textdumps don't
contain sensitive data by design as a user decides what information should be
dumped.
savecore(8) writes the kernel dump key to a key.# file if its size in the header
is nonzero. # is the number of the current core dump.
decryptcore(8) decrypts the core dump using a private RSA key and the kernel
dump key. This is performed by a child process in capability mode.
If the decryption was not successful the parent process removes a partially
decrypted core dump.
Description on how to encrypt crash dumps was added to the decryptcore(8),
dumpon(8), rc.conf(5) and savecore(8) manual pages.
EKCD was tested on amd64 using bhyve and i386, mipsel and sparc64 using QEMU.
The feature still has to be tested on arm and arm64 as it wasn't possible to run
FreeBSD due to the problems with QEMU emulation and lack of hardware.
Designed by: def, pjd
Reviewed by: cem, oshogbo, pjd
Partial review: delphij, emaste, jhb, kib
Approved by: pjd (mentor)
Differential Revision: https://reviews.freebsd.org/D4712
- Defined an abstract NVRAM I/O API (bhnd_nvram_io), decoupling NVRAM/SPROM
parsing from the actual underlying NVRAM data provider (e.g. CFE firmware
devices).
- Defined an abstract NVRAM data API (bhnd_nvram_data), decoupling
higher-level NVRAM operations (indexed lookup, data conversion, etc) from
the underlying NVRAM file format parsing/serialization.
- Implemented a new high-level bhnd_nvram_store API, providing indexed
variable lookup, pending write tracking, etc on top of an arbitrary
bhnd_nvram_data instance.
- Migrated all bhnd(4) NVRAM device drivers to the common bhnd_nvram_store
API.
- Implemented a common bhnd_nvram_val API for parsing/encoding NVRAM
variable values, including applying format-specific behavior when
converting to/from the NVRAM string representations.
- Dropped the now unnecessary bhnd_nvram driver, and moved the
broadcom/mips-specific CFE NVRAM driver out into sys/mips/broadcom.
- Implemented a new nvram_map file format:
- Variable definitions are now defined separately from the SPROM
layout. This will also allow us to define CIS tuple NVRAM
mappings referencing the common NVRAM variable definitions.
- Variables can now be defined within arbitrary named groups.
- Textual descriptions and help information can be defined inline
for both variables and variable groups.
- Implemented a new, compact encoding of SPROM image layout
offsets.
- Source-level (but not build system) support for building the NVRAM file
format APIs (bhnd_nvram_io, bhnd_nvram_data, bhnd_nvram_store) as a
userspace library.
The new compact SPROM image layout encoding is loosely modeled on Apple
dyld compressed LINKEDIT symbol binding opcodes; it provides a compact
state-machine encoding of the mapping between NVRAM variables and the SPROM
image offset, mask, and shift instructions necessary to decode or encode
the SPROM variable data.
The compact encoding reduces the size of the generated SPROM layout data
from roughly 60KB to 3KB. The sequential nature SPROM layout opcode tables
also simplify iteration of the SPROM variables, as it's no longer
neccessary to iterate the full NVRAM variable definition table, but
instead simply scan the SPROM revision's layout opcode table.
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D8645
an invalid address. It is also unneeded on arm64 as we use the ARM Generic
Timer driver.
Obtained from: ABT Systems Ltd
Sponsored by: The FreeBSD Foundation
Summary:
This implements part of the gpio-poweroff and gpio-restart device tree
bindings. Optional properties are not handled currently. It also currently
only supports level-triggered reset.
Reviewed By: gonzo
Differential Revision: https://reviews.freebsd.org/D8521
It's usefull for development (for netboot) and it also helps to boot
FreeBSD on some embeded platforms (where we must boot kernel directly,
without standard boot loader).
MFC after: 3 weeks
- Split driver in two parts: FDT and non-FDT
- Instead of reattach gpioled nodes to GPIO bus use
gpio_pin_get_by_ofw_idx and add ofwbus and simplebus as parrent buses
Reviewed by: loos
Differential Revision: https://reviews.freebsd.org/D8233
A grant-table user-space device will allow user-space applications to map
and share grants (Xen way to share memory) among Xen domains. This grant
table user-space device has been tested with the QEMU Qdisk Xen backed.
Submitted by: jaggi
Reviewed by: royger
Differential review: https://reviews.freebsd.org/D7293
Summary:
The hardware does not expose a classic SMBus interface.
Instead it has a lower level interface that can express a far richer
I2C protocol than what smbus offers. However, the interface does not
provide a way to explicitly generate the I2C stop and start conditions.
It's only possible to request that the stop condition is generated
after transferring the next byte in either direction. So, at least
one data byte must always be transferred.
Thus, some I2C sequences are impossible to generate, e.g., an equivalent
of smbus quick command (<start>-<slave addr>-<r/w bit>-<stop>).
At the same time isl(4) and cyapa(4) are moved to iicbus and now they use
iicbus_transfer for communication. Previously they used smbus_trans()
interface that is not defined by the SMBus protocol and was implemented
only by ig4(4). In fact, that interface was impossible to implement
for the typical SMBus controllers like intpm(4) or ichsmb(4) where
a type of the SMBus command must be programmed.
The plan is to remove smbus_trans() and all its uses.
As an aside, the smbus_trans() method deviates from the standard,
but perhaps backwards, FreeBSD convention of using 8-bit slave
addresses (shifted by 1 bit to the left). The method expects
7-bit addresses.
There is a user facing consequence of this change.
A user must now provide device hints for isl and cyapa that specify an iicbus to use
and a slave address on it.
On Chromebook hardware where isl and cyapa devices are commonly found
it is also possible to use a new chromebook_platform(4) driver that
automatically configures isl and cyapa devices. There is no need to
provide the device hints in that case,
Right now smbus(4) driver tries to discover all slaves on the bus.
That is very dangerous. Fortunately, the probing code uses smbus_trans()
to do its job, so it is really enabled for ig4 only.
The plan is to remove that auto-probing code and smbus_trans().
Tested by: grembo, Matthias Apitz <guru@unixarea.de> (w/o
chromebook_platform)
Discussed with: grembo, imp
Reviewed by: wblock (docs)
MFC after: 1 month
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D8172
The driver currently supports chips that are fully compliant with the
JEDEC SPD / EEPROM / TS standard (JEDEC Standard 21-C,
TSE2002 Specification, frequenlty referred to as JEDEC JC 42.4).
Additionally some chips from STMicroelectronics are supported as well.
They are compliant except for their Device ID pattern.
Given the continued lack of any common sensor infrastructure, the driver
uses an ad-hoc sysctl to report the temperature.
Reviewed by: wblock (documentation)
MFC after: 2 weeks
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D8174
All devices:
- add support for rate adaptation via ieee80211_amrr(9);
- use short preamble for transmitted frames when needed;
- multi-bss support:
* for RTL8821AU: 2 VAPs at the same time;
* other: 1 any VAP + 1 sta VAP.
RTL8188CE:
- fix IQ calibration bug (reason of significant speed degradation);
- add h/w crypto acceleration support.
USB:
- A-MPDU Tx support;
- short GI support;
Other:
- add support for RTL8812AU / RTL8821AU chipsets
(a/b/g/n only; no ac yet);
- split merged code into subparts:
* bus glue (usb/*, pci/*, rtl*/usb/*, rtl*/pci/*)
* common (if_rtwn*)
* chip-specific (rtl*/*)
- various other bugfixes.
Due to code reorganization, module names / requirements were changed too:
urtwn urtwnfw -> rtwn rtwn_usb rtwnfw
rtwn rtwnfw -> rtwn rtwn_pci rtwnfw
Tested with RTL8188CE, RTL8188CUS, RTL8188EU and RTL8821AU.
Tested by: kevlo, garga,
Peter Garshtja <peter.garshtja@ambient-md.com>,
Kevin McAleavey <kevin.mcaleavey@knosproject.com>,
Ilias-Dimitrios Vrachnis <id@vrachnis.com>,
<otacilio.neto@bsd.com.br>
Relnotes: yes
This commit, long overdue, contains contributions in the last 2 years
from Stefano Garzarella, Giuseppe Lettieri, Vincenzo Maffione, including:
+ fixes on monitor ports
+ the 'ptnet' virtual device driver, and ptnetmap backend, for
high speed virtual passthrough on VMs (bhyve fixes in an upcoming commit)
+ improved emulated netmap mode
+ more robust error handling
+ removal of stale code
+ various fixes to code and documentation (some mixup between RX and TX
parameters, and private and public variables)
We also include an additional tool, nmreplay, which is functionally
equivalent to tcpreplay but operating on netmap ports.
userland. It supports userland interfaces to UEFI Runtime Services. This is
indended to the the MI portion of EFI RuntimeServices support.
Differential Revision: https://reviews.freebsd.org/D8128
Reviewed by: kib@, wblock@, Ganael Laplanche
like other PCI network drivers. The sys/ofed directory is now mainly
reserved for generic infiniband code, with exception of the mthca driver.
- Add new manual page, mlx4en(4), describing how to configure and load
mlx4en.
- All relevant driver C-files are now prefixed mlx4, mlx4_en and
mlx4_ib respectivly to avoid object filename collisions when compiling
the kernel. This also fixes an issue with proper dependency file
generation for the C-files in question.
- Device mlxen is now device mlx4en and depends on device mlx4, see
mlx4en(4). Only the network device name remains unchanged.
- The mlx4 and mlx4en modules are now built by default on i386 and
amd64 targets. Only building the mlx4ib module depends on
WITH_OFED=YES .
Sponsored by: Mellanox Technologies
There is nothing CPU specific here, and it's usable by both fdt and Open
Firmware based systems. Rather than keeping the same file in every one, just
add it to the ofw/fdt block in the main file.
evdev is a generic input event interface compatible with Linux
evdev API at ioctl level. It allows using unmodified (apart from
header name) input evdev drivers in Xorg, Wayland, Qt.
This commit has only generic kernel API. evdev support for individual
hardware drivers like ukbd, ums, atkbd, etc. will be committed later.
Project was started by Jakub Klama as part of GSoC 2014. Jakub's
evdev implementation was later used as a base, updated and finished
by Vladimir Kondratiev.
Submitted by: Vladimir Kondratiev <wulf@cicgroup.ru>
Reviewed by: adrian, hans
Differential Revision: https://reviews.freebsd.org/D6998
The cxgbev/cxlv driver supports Virtual Function devices for Chelsio
T4 and T4 adapters. The VF devices share most of their code with the
existing PF4 driver (cxgbe/cxl) and as such the VF device driver
currently depends on the PF4 driver.
Similar to the cxgbe/cxl drivers, the VF driver includes a t4vf/t5vf
PCI device driver that attaches to the VF device. It then creates
child cxgbev/cxlv devices representing ports assigned to the VF.
By default, the PF driver assigns a single port to each VF.
t4vf_hw.c contains VF-specific routines from the shared code used to
fetch VF-specific parameters from the firmware.
t4_vf.c contains the VF-specific PCI device driver and includes its
own attach routine.
VF devices are required to use a different firmware request when
transmitting packets (which in turn requires a different CPL message
to encapsulate messages). This alternate firmware request does not
permit chaining multiple packets in a single message, so each packet
results in a firmware request. In addition, the different CPL message
requires more detailed information when enabling hardware checksums,
so parse_pkt() on VF devices must examine L2 and L3 headers for all
packets (not just TSO packets) for VF devices. Finally, L2 checksums
on non-UDP/non-TCP packets do not work reliably (the firmware trashes
the IPv4 fragment field), so IPv4 checksums for such packets are
calculated in software.
Most of the other changes in the non-VF-specific code are to expose
various variables and functions private to the PF driver so that they
can be used by the VF driver.
Note that a limited subset of cxgbetool functions are supported on VF
devices including register dumps, scheduler classes, and clearing of
statistics. In addition, TOE is not supported on VF devices, only for
the PF interfaces.
Reviewed by: np
MFC after: 2 months
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D7599
This defines a new bhnd_erom_if API, providing a common interface to device
enumeration on siba(4) and bcma(4) devices, for use both in the bhndb bridge
and SoC early boot contexts, and migrates mips/broadcom over to the new API.
This also replaces the previous adhoc device enumeration support implemented
for mips/broadcom.
Migration of bhndb to the new API will be implemented in a follow-up commit.
- Defined new bhnd_erom_if interface for bhnd(4) device enumeration, along
with bcma(4) and siba(4)-specific implementations.
- Fixed a minor bug in bhndb that logged an error when we attempted to map the
full siba(4) bus space (18000000-17FFFFFF) in the siba EROM parser.
- Reverted use of the resource's start address as the ChipCommon enum_addr in
bhnd_read_chipid(). When called from bhndb, this address is found within the
host address space, resulting in an invalid bridged enum_addr.
- Added support for falling back on standard bus_activate_resource() in
bhnd_bus_generic_activate_resource(), enabling allocation of the bhnd_erom's
bhnd_resource directly from a nexus-attached bhnd(4) device.
- Removed BHND_BUS_GET_CORE_TABLE(); it has been replaced by the erom API.
- Added support for statically initializing bhnd_erom instances, for use prior
to malloc availability. The statically allocated buffer size is verified both
at runtime, and via a compile-time assertion (see BHND_EROM_STATIC_BYTES).
- bhnd_erom classes are registered within a module via a linker set, allowing
mips/broadcom to probe available EROM parser instances without creating a
strong reference to bcma/siba-specific symbols.
- Migrated mips/broadcom to bhnd_erom_if, replacing the previous MIPS-specific
device enumeration implementation.
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D7748
Idle page zeroing has been disabled by default on all architectures since
r170816 and has some bugs that make it seemingly unusable. Specifically,
the idle-priority pagezero thread exacerbates contention for the free page
lock, and yields the CPU without releasing it in non-preemptive kernels. The
pagezero thread also does not behave correctly when superpage reservations
are enabled: its target is a function of v_free_count, which includes
reserved-but-free pages, but it is only able to zero pages belonging to the
physical memory allocator.
Reviewed by: alc, imp, kib
Differential Revision: https://reviews.freebsd.org/D7714
cnv API is a set of functions for managing name/value pairs by cookie.
The cookie can be obtained by nvlist_next(), nvlist_get_parent() or
nvlist_get_pararr() function. This patch also includes unit tests.
Submitted by: Adam Starak <starak.adam@gmail.com>
- Added bhnd_pmu driver implementations for PMU and PWRCTL chipsets,
derived from Broadcom's ISC-licensed HND code.
- Added bhnd bus-level support for routing per-core clock and resource
power requests to the PMU device.
- Lift ChipCommon support out into the bhnd module, dropping
bhnd_chipc.
Reviewed by: mizhka
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D7492
Essentially, this is a literal copy of the code in sys/compat/cloudabi64,
except that it now makes use of 32-bits datatypes and limits. In
sys/conf/files, we now need to take care to build the code in
sys/compat/cloudabi if either COMPAT_CLOUDABI32 or COMPAT_CLOUDABI64 is
turned on.
This change does not yet include any of the CPU dependent bits. Right
now I have implementations for running i386 binaries both on i386 and
x86-64, which I will send out for review separately.
This driver only supports 10Mb Ethernet using PIO (the hardware supports
DMA, but the driver only does PIO). There are not any PCCard adapters
supported by this driver, only ISA cards. In addition, it does not use
bus_space but instead uses bcopy with volatile pointers triggering a
host of warnings. (if_ie.c is one of 3 files always built with
-Wno-error)
Relnotes: yes
The wl(4) driver supports pre-802.11 PCCard wireless adapters that
are slower than 802.11b. They do not work with any of the 802.11
framework and the driver hasn't been reported to actually work in a
long time.
Relnotes: yes
The si(4) driver supported multiport serial adapters for ISA, EISA, and
PCI buses. This driver does not use bus_space, instead it depends on
direct use of the pointer returned by rman_get_virtual(). It is also
still locked by Giant and calls for patch testing to convert it to use
bus_space were unanswered.
Relnotes: yes
- Added a generic bhnd_nvram_parser API, with support for the TLV format
used on WGT634U devices, the standard BCM NVRAM format used on most
modern devices, and the "board text file" format used on some hardware
to supply external NVRAM data at runtime (e.g. via an EFI variable).
- Extended the bhnd_bus_if and bhnd_nvram_if interfaces to support both
string-based and primitive data type variable access, required for
common behavior across both SPROM and NVRAM data sources.
- Extended the existing SPROM implementation to support the new
string-based NVRAM APIs.
- Added an abstract bhnd_nvram driver, implementing the bhnd_nvram_if
atop the bhnd_nvram_parser API.
- Added a CFE-based bhnd_nvram driver to provide read-only access to
NVRAM data on MIPS SoCs, pending implementation of a flash-aware
bhnd_nvram driver.
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D7489
This is a driver for a pre-ATAPI ISA CD-ROM adapter. As noted in
the manpage, this driver is only useful as a backend to cdcontrol to
play audio CDs since it doesn't use DMA, so its data performance is
"abysmal" (and that was true in the mid 90's).
The module works together with ipfw(4) and implemented as its external
action module.
Stateless NAT64 registers external action with name nat64stl. This
keyword should be used to create NAT64 instance and to address this
instance in rules. Stateless NAT64 uses two lookup tables with mapped
IPv4->IPv6 and IPv6->IPv4 addresses to perform translation.
A configuration of instance should looks like this:
1. Create lookup tables:
# ipfw table T46 create type addr valtype ipv6
# ipfw table T64 create type addr valtype ipv4
2. Fill T46 and T64 tables.
3. Add rule to allow neighbor solicitation and advertisement:
# ipfw add allow icmp6 from any to any icmp6types 135,136
4. Create NAT64 instance:
# ipfw nat64stl NAT create table4 T46 table6 T64
5. Add rules that matches the traffic:
# ipfw add nat64stl NAT ip from any to table(T46)
# ipfw add nat64stl NAT ip from table(T64) to 64:ff9b::/96
6. Configure DNS64 for IPv6 clients and add route to 64:ff9b::/96
via NAT64 host.
Stateful NAT64 registers external action with name nat64lsn. The only
one option required to create nat64lsn instance - prefix4. It defines
the pool of IPv4 addresses used for translation.
A configuration of instance should looks like this:
1. Add rule to allow neighbor solicitation and advertisement:
# ipfw add allow icmp6 from any to any icmp6types 135,136
2. Create NAT64 instance:
# ipfw nat64lsn NAT create prefix4 A.B.C.D/28
3. Add rules that matches the traffic:
# ipfw add nat64lsn NAT ip from any to A.B.C.D/28
# ipfw add nat64lsn NAT ip6 from any to 64:ff9b::/96
4. Configure DNS64 for IPv6 clients and add route to 64:ff9b::/96
via NAT64 host.
Obtained from: Yandex LLC
Relnotes: yes
Sponsored by: Yandex LLC
Differential Revision: https://reviews.freebsd.org/D6434
* make interface cloner VNET-aware;
* simplify cloner code and use if_clone_simple();
* migrate LOGIF_LOCK() to rmlock;
* add ipfw_bpf_mtap2() function to pass mbuf to BPF;
* introduce new additional ipfwlog0 pseudo interface. It differs from
ipfw0 by DLT type used in bpfattach. This interface is intended to
used by ipfw modules to dump packets with additional info attached.
Currently pflog format is used. ipfw_bpf_mtap2() function uses second
argument to determine which interface use for dumping. If dlen is equal
to ETHER_HDR_LEN it uses old ipfw0 interface, if dlen is equal to
PFLOG_HDRLEN - ipfwlog0 will be used.
Obtained from: Yandex LLC
Sponsored by: Yandex LLC
- Move group task queue into kern/subr_gtaskqueue.c
- Change intr_enable to return an int so it can be detected if it's not
implemented
- Allow different TX/RX queues per set to be different sizes
- Don't split up TX mbufs before transmit
- Allow a completion queue for TX as well as RX
- Pass the RX budget to isc_rxd_available() to allow an earlier return
and avoid multiple calls
Submitted by: shurd
Reviewed by: gallatin
Approved by: scottl
Differential Revision: https://reviews.freebsd.org/D7393
CloudABI executables already provide support for passing in vDSOs. This
functionality is used by the emulator for OS X to inject system call
handlers. On FreeBSD, we could use it to optimize calls to
gettimeofday(), etc.
Though I don't have any plans to optimize any system calls right now,
let's go ahead and already pass in a vDSO. This will allow us to
simplify the executables, as the traditional "syscall" shims can be
removed entirely. It also means that we gain more flexibility with
regards to adding and removing system calls.
Reviewed by: kib
Differential Revision: https://reviews.freebsd.org/D7438
_prison_check_ip4 renamed to prison_check_ip4_locked
Move IPv6-specific jail functions to new file netinet6/in6_jail.c
_prison_check_ip6 renamed to prison_check_ip6_locked
Add appropriate prototypes to sys/sys/jail.h
Adjust kern_jail.c to call prison_check_ip4_locked and
prison_check_ip6_locked accordingly.
Add netinet/in_jail.c and netinet6/in6_jail.c to the list of files that
need to be built when INET and INET6, respectively, are configured in the
kernel configuration file.
Reviewed by: jtl
Approved by: sjg (mentor)
Sponsored by: Juniper Networks, Inc.
Differential Revision: https://reviews.freebsd.org/D6799
per-protocol. This reduces the number scsi symbols references by
cam_xpt significantly, and eliminates all ata / nvme symbols. There's
still some NVME / ATA specific code for dealing with XPT_NVME_IO and
XPT_ATA_IO respectively, and a bunch of scsi-specific code, but this
is progress.
Differential Revision: https://reviews.freebsd.org/D7289
- Move cr_canseeinpcb to sys/netinet/in_prot.c in order to separate the
INET and INET6-specific code from the rest of the prot code (It is only
used by the network stack, so it makes sense for it to live with the
other network stack code.)
- Move cr_canseeinpcb prototype from sys/systm.h to netinet/in_systm.h
- Rename cr_seeotheruids to cr_canseeotheruids and cr_seeothergids to
cr_canseeothergids, make them non-static, and add prototypes (so they
can be seen/called by in_prot.c functions.)
- Remove sw_csum variable from ip6_forward in ip6_forward.c, as it is an
unused variable.
Reviewed by: gnn, jtl
Approved by: sjg (mentor)
Sponsored by: Juniper Networks, Inc.
Differential Revision: https://reviews.freebsd.org/D2901
f/w for the other devices supported by this driver.
Patch linked in https://reviews.freebsd.org/D6967 but not actually
a part of the review.
Obtained from DragonflyBSD.
Submitted by: Kevin Bowling <kev009@kev009.com>
MFC after: 2 weeks
Relnotes: yes
Chelsio NICs are a bit unique compared to some other NICs in that they
expose different functionality on different physical functions. In
particular, PF4 is used to manage the NIC interfaces ('t4nex' and 't5nex').
However, PF4 is not able to create VF devices. Instead, VFs are only
supported by physical functions 0 through 3. This commit adds 't4iov'
and 't5iov' drivers that attach to PF0-3.
One extra wrinkle is that the iov devices cannot enable SR-IOV until the
firwmare has been initialized by the main PF4 driver. To handle this
case, a new t4_if kobj interface has been added to permit cross-calls
between the PF drivers. The PF4 driver notifies sibling drivers when it
is fully attached. It also requests sibling drivers to detach before it
detaches. Sibling drivers query the PF4 driver during their attach
routine to see if it is attached. If not, the sibling drivers defer
their attach actions until the PF4 driver informs them it is attached.
VF devices are associated with a single port on the NIC. VF devices
created from PF0 are associated with the first port on the NIC, VFs
from PF1 are associated with the second port, etc. VF devices can
only be created from a PF device that has an associated port. Thus,
on a 2-port card, VFs are only supported on PF0 and PF1.
Reviewed by: np (earlier versions)
MFC after: 1 month
Sponsored by: Chelsio Communications
as defined in RFC 6296. The module works together with ipfw(4) and
implemented as its external action module. When it is loaded, it registers
as eaction and can be used in rules. The usage pattern is similar to
ipfw_nat(4). All matched by rule traffic goes to the NPT module.
Reviewed by: hrs
Obtained from: Yandex LLC
MFC after: 1 month
Relnotes: yes
Sponsored by: Yandex LLC
Differential Revision: https://reviews.freebsd.org/D6420
Now that bhnd(4) provides feature parity with the previous siba/mips
implementation, we can switch sentry5 over and begin lifting common
support code out for use across bhnd(4) embedded targets.
Changes:
- Fixed enumeration of siba(4) per-core address maps, required for
discovery of memory mapped chipc flash region on siba(4) devices.
- Simplified bhnd kernel configuration (dropped 'bhndbus' option).
- Replaced files.broadcom's direct file references with their
corresponding standard kernel options.
- Lifted out common bcma/siba nexus support, inheriting from the new
generic bhnd_nexus driver.
- Dropped now-unused sentry5 siba code.
- Re-integrated BCM into the universe build now that it actually compiles.
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D6712
This is the initial framework to call into the MCI HAL routines and drive
the basic state engine.
The MCI bluetooth coex model uses a command channel between wlan and
bluetooth, rather than a 2-wire or 3-wire signaling protocol to control things.
This means the wlan and bluetooth chip exchange a lot more information and
signaling, even at the per-packet level. The NICs in question can share
the input LNA and output PA on the die, so they absolutely can't stomp
on each other in a silly fashion. It also allows for the bluetooth side
to signal when profiles come and go, so the driver can take appropriate
control. There's also the possibility of dynamic bluetooth/wlan duty cycle
control which I haven't yet really played with.
It configures things up with a static "wlan wins everything" coexistence,
configures up the available 2GHz channel map for bluetooth, sets a static
duty cycle for bluetooth/wifi traffic priority and drives the basics needed to
keep the MCI HAL code happy.
It doesn't do any actual coexistence except to default to "wlan wins everything",
which at least demonstrates that things do indeed work. Bluetooth inquiry frames
still trump wifi (including beacons), so that demonstrates things really do
indeed seem to work.
Tested:
* AR9462 (WB222), STA mode + bt
* QCA9565 (WB335), STA mode + bt
TODO:
* .. the rest of coexistence. yes, bluetooth, not people. That stuff's hard.
* It doesn't do the initial BT side calibration, which requires a WLAN chip
reset. I'll fix up the reset path a bit more first before I enable that.
* The 1-ant and 2-ant configuration bits aren't being set correctly in
if_ath_btcoex.c - I'll dig into that and fix it in a subsequent commit.
* It's not enabled by default for WB222/WB225 even though I believe it now
can be - I'll chase that up in a subsequent commit.
Obtained from: Qualcomm Atheros, Linux ath9k
Support for the new hashing algorithms in ZFS was introduced in r289422
However it was disconnected because FreeBSD lacked implementations of
SHA-512 (truncated to 256 bits), and Skein.
These implementations were introduced in r300921 and r300966 respectively
This commit connects them to ZFS and enabled these new checksum algorithms
This new algorithms are not supported by the boot blocks, so do not use them
on your root dataset if you boot from ZFS.
Relnotes: yes
Sponsored by: ScaleEngine Inc.
This is a simple ioctl and mmap API to issue SPI transactions from
userland. It's useful for simple devices (eg spi temperature sensors,
etc) for experimentation.
TODO:
* Write some documentation!
Submitted by: green
This patchset adds support to bhnd_chipc for sharing SYS_RES_MEMORY
resources with its children, allowing us to hang devices off of
bhnd_chipc that rely on access to a subset of the device register space
that bhnd_chipc itself must also allocate.
We could avoid most of this heavy lifting if RF_SHAREABLE+SYS_RES_MEMORY
wasn't limited to use with allocations at the same size/offset.
As a work-around, I implemented something similar to vga_pci.c, which
implements similar reference counting of of PCI BAR resources for its
children.
With these changes, chipc will use reference counting of SYS_RES_MEMORY
allocation/activation requests, to decide when to allocate/activate/
deactivate/release resources from the parent bhnd(4) bus.
The requesting child device is allocated a new resource from chipc's
rman, pointing to (possibly a subregion of) the refcounted bhnd resources
allocated by chipc.
Other resource types are just passed directly to the parent bhnd bus;
RF_SHAREABLE works just fine with IRQs.
I also lifted the SPROM device code out into a common driver, since this
now allows me to hang simple subclasses off of a common driver off of both
bhndb_pci and bhnd_chipc.
Tested:
* (landonf) Tested against BCM4331 and BCM4312, confirmed that SPROM still
attaches and can be queried.
Submitted by: Landon Fuller <landonf@landonf.org>
Reviewed by: mizkha@gmail.com
Differential Revision: https://reviews.freebsd.org/D6471
This adds a BHND_BUS_GET_ATTACH_TYPE(); the primary use-case is to let
chipc make a coarse-grained determination as to whether UART, SPI, etc
drivers ought to be attached, and on fullmac devices, whether a real
CPU driver ought to be skipped for the ARM core, etc.
Tested:
* BCM4331 (BHND)
* BCM4312 (SIBA)
Submitted by: Landon Fuller <landonf@landonf.org>
Differential Revision: https://reviews.freebsd.org/D6492
"iflib is a library to eliminate the need for frequently duplicated device
independent logic propagated (poorly) across many network drivers."
Participation is purely optional. The IFLIB kernel config option is
provided for drivers that want to transition between legacy and iflib
modes of operation. ixl and ixgbe driver conversions will be committed
shortly. We hope to see participation from the Broadcom and maybe
Chelsio drivers in the near future.
Submitted by: mmacy@nextbsd.org
Reviewed by: gallatin
Differential Revision: D5211
* The default kernel and options won't build the GPL PHY bits;
* bwn(4) defaults to building as a module anyway!;
* If BWN_GPL_PHY is specified in the config file, and you uncomment
the GPL PHY bits in the module Makefile, you'll get a working
N-PHY.
This is specifically designed to be obtuse for now, as I don't want
to flip it on by default. It's easy enough for people to flip on
and build, and it's a module so the default GENERIC kernel won't be
GPL tainted.
I'll have to add an actual HAL layer that allows the GPL PHY to be loaded
before if_bwn so it can be "magic", but that'll come later.
Tested:
* BCM4321 11abg NIC, STA mode
Now that we've got access to SPROM and can access board identification,
this implements all known remaining hardware work-arounds for the bhnd(4)
PCI and PCIe-G1 cores operating endpoint mode.
Additionally, this adds an initial set of skeleton PCIe-G2 hostb and pcib
drivers, required by fullmac and newer softmac devices.
Submitted by: Landon Fuller <landonf@landonf.org>
Differential Revision: https://reviews.freebsd.org/D6377
These firmwares were obtained from the "Chelsio T5/T4 Unified Wire
v2.12.0.3 for Linux" release. Changes since 1.14.4.0 (which is the
firmware in -STABLE branches) are in the "Release Notes" accompanying
the Unified Wire release and are copy-pasted here as well.
22.1. T5 Firmware
+++++++++++++++++++++++++++++++++
Version : 1.15.37.0
Date : 04/27/2016
================================================================================
FIXES
-----
BASE:
- Fixed an issue in FW_RSS_VI_CONFIG_CMD handling where the default ingress
queue was ignored.
- Fixed an issue where adapter failed to load fw by adjusting DRAM frequency.
- Fixed an issue in watchdog which was causing VM bring-up failure after reboot.
- Fixed 40G link failures with some switches when auto-negotiation enabled.
- Fixed to improve on link bring-up time.
- Per port buffer groups size doubled to improve performance.
- Fixed an issue where bogus d3hot bits were set causing traffic stall.
- Fixed an issue where sometimes adapter was not seen after reboot.
- Fixed an issue where iWARP was crashing in conjunction with traffic management.
- Fixed an issue where link failed to come up after removing twinax cable and
inserting optical module.
ETH
- Fixed a link flap issue on T580-CR.
OFLD
- Fixed a potential iSCSI data corruption issue by disabling RxFragEn flag.
FOiSCSI
- Fixed an issue in recovery path where connection was getting closed before
recovery processing was done.
- Fixed an issue in TCP port reuse.
- Fixed an issue in recovery path when large number (>64) of iSCSI connections
were in use.
- Returned ENETUNREACH if IP was not been provisioned yet and driver tried to
use given inerface.
- Fixed an issue where fw was sending ENETUNREACH event for normal tcp
disconnection.
DCBX
- Fixed an issue where iscsi tlv is sent incorrectly to host. (DCBX CEE)
- Fixed an issue where apply bit set for APP id was affecting the ETS and PFC
settings.(DCBX IEEE)
- Fixed an issue where app priority values are not handled correctly in fw.
(DCBX IEEE)
- Fixed an issue where enable/disable dcbx can cause crash. (DCBX CEE,DCBX IEEE)
FOFCoE
- Removed BB6 support.
ENHANCEMENTS
------------
BASE:
- Added new interface to program DCA settings in SGE contexts; allow 32-byte
IQE size
- Added PTP interface fw_ptp_ts to support PTP Frequeny and Offset adjustment.
- Added MPS raw interface.
ETH:
- New mailbox command FW_DCB_IEEE_CMD api added for IEEE dcbx.
OFLD:
- WR opcode is returned to host in cqe error response.
22.2. T4 Firmware
+++++++++++++++++
Version : 1.15.37.0
Date : 04/27/2016
================================================================================
FIXES
-----
BASE:
- Fixed an issue in FW_RSS_VI_CONFIG_CMD handling where default ingress queue
was ignored.
- Fixed an issue in watchdog which was causing VM bring-up failure after reboot.
- Per port buffer groups size doubled to improve performance.
- Fixed an issue where iWARP was crashing in conjunction with traffic management.
FOiSCSI:
- Fixed an issue in recovery path where connection was getting closed before
recovery processing was done.
- Fixed an issue in TCP port reuse.
- Fixed an issue in recovery path when large number (>64) of iSCSI connections
were in use.
- Returned ENETUNREACH if IP had not been provisioned yet and driver tried to
use given inerface.
DCBX
- Fixed an issue where iscsi tlv is sent incorrectly to host.(DCBX CEE)
- Fixed an issue where enable/disable dcbx can cause crash in firmware.(DCBX CEE)
FOiSCSI
- Fixes an issue where fw was sending ENETUNREACH event for normal tcp
disconnection.
FOFCoE
- Removed BB6 support.
ENHANCEMENTS
------------
BASE:
- Added MPS raw interface.
ETH:
- New mailbox command FW_DCB_IEEE_CMD api added for IEEE dcbx.
================================================================================
Obtained from: Chelsio Communications
MFC after: 6 weeks
Relnotes: yes
Sponsored by: Chelsio Communications
gpiokey driver implements functional subset of gpiokeys device-tree bindings:
https://www.kernel.org/doc/Documentation/devicetree/bindings/input/gpio-keys.txt
It acts as a virtual keyboard, so keys are visible through kbdmux(4)
Driver maps linux scancodes for most common keys to FreeBSD scancodes and
also extends spec by introducing freebsd,code property to specify
FreeBSD-native scancodes.
Reviewed by: mmel, jmcneill
Differential Revision: https://reviews.freebsd.org/D6279
legacy siba sentry5 cpu glue.
The siba_cc code is the hard-coded chipcommon bits for the sentry s5,
which will eventually be replaced with the more flexible bhnd sipa/cc
code.
bwn, etc uses siba_bwn, which doesn't use siba or siba_cc to do anything.
Turns out that ye olde siba.c is /just/ the siba mips code (used by
the initial SENTRY5 port. However, I don't think it was ever
finished enough to be useful, and I do have this nagging feeling
that we'll eventually replace it with the bhnd code.
But, since bhnd(4) introduced siba.c too, we ended up with a
source file name clash, and that broke the SENTRY5 build.
It /looks/ like this is the only place siba.c / device siba is
used.
This adds support for the NVRAM handling and the basic SPROM
hardware used on siba(4) and bcma(4) devices, including:
* SPROM directly attached to the PCI core, accessible via PCI configuration
space.
* SPROM attached to later ChipCommon cores.
* SPROM variables vended from the parent SoC bus (e.g. via a directly-attached
flash device).
Additional improvements to the NVRAM/SPROM interface will
be required, but this changeset stands alone as working
checkpoint.
Submitted by: Landon Fuller <landonf@landonf.org>
Reviewed by: Michael Zhilin <mizkha@gmail.com> (Broadcom MIPS support)
Differential Revision: https://reviews.freebsd.org/D6196
This is an initial work in progress to use the replacement bhnd
bus code for devices which support it.
* Add manpage updates for bhnd, bhndb, siba
* Add kernel options for bhnd, bhndbus, etc
* Add initial support in if_bwn_pci / if_bwn_mac for using bhnd
as the bus transport for suppoted NICs
* if_bwn_pci will eventually be the PCI bus glue to interface to bwn,
which will use the right backend bus to attach to, versus direct
nexus/bhnd attachments (as found in embedded broadcom devices.)
The PCI glue defaults to probing at a lower level than the bwn glue,
so bwn should still attach as per normal without a boot time tunable set.
It's also not fully fleshed out - the bwn probe/attach code needs to be
broken out into platform and bus specific things (just like ath, ath_pci,
ath_ahb) before we can shift the driver over to using this.
Tested:
* BCM4311, STA mode
* BCM4312, STA mode
Submitted by: Landon Fuller <landonf@landonf.org>
Differential Revision: https://reviews.freebsd.org/D6191
* Break out the 'g' phy code;
* Break out the debugging bits into a separate source file, since
some debugging prints are done in the phy code;
* Make some more chip methods in if_bwn.c public.
This brings the size of if_bwn.c down to 6,805 lines which is now
approaching managable.
This (and eventually migrating the other PHY code out) is in preparation
for adding the 11n PHY. No, the 11ac PHY (for the BCM4260 softmac part) isn't
yet open source, so we can't grow that. Yet.
This trims ~3,700 lines of code from if_bwn.c, bringing it down to a slightly
less crazy sounding 10,446 lines of code.
fdt_static_dtb.S dependency in sys/conf/files is currently set as:
$S/boot/fdt/dts/${MACHINE}/${FDT_DTS_FILE}
This is wrong, as what fdt_static_dtb.S actually uses is the DTB file
produced from the FDT_DTS_FILE.
In addition it also makes using DTS files stored in $S/gnu/dts/${MACHINE}/
impossible.
So, change the dependency to "fdt_dtb_file", which seems to be the right
option here anyway.
Approved by: adrian (mentor)
Sponsored by: Smartcom - Bulgaria AD
Differential Revision: https://reviews.freebsd.org/D5963
It allows implementing loadable kernel modules with new actions and
without needing to modify kernel headers and ipfw(8). The module
registers its action handler and keyword string, that will be used
as action name. Using generic syntax user can add rules with this
action. Also ipfw(8) can be easily modified to extend basic syntax
for external actions, that become a part base system.
Sample modules will coming soon.
Obtained from: Yandex LLC
Sponsored by: Yandex LLC
as before. The common scheduling bits have moved from inline code in
each of the CAM periph drivers into a library that implements the
default scheduling.
In addition, a number of rate-limiting and I/O preference options can
be enabled by adding CAM_IOSCHED_NETFLIX to your config file. A number
of extra stats are also maintained. CAM_IOSCHED_NETFLIX isn't on by
default because it uses a separate BIO_READ and BIO_WRITE queue, so
doesn't honor BIO_ORDERED between these two types of operations. We
already didn't honor it for BIO_DELETE, and we don't depend on
BIO_ORDERED between reads and writes anywhere in the system (it is
currently used with BIO_FLUSH in ZFS to make sure some writes are
complete before others start and as a poor-man's soft dependency in
one place in UFS where we won't be issuing READs until after the
operation completes). However, out of an abundance of caution, it
isn't enabled by default.
Plus, this also brings in NCQ TRIM support for those SSDs that support
it. A black list is also provided for known rogues that use NCQ trim
as an excuse to corrupt the drive. It was difficult to separate out
into a separate commit.
This code has run in production at Netflix for over a year now.
Sponsored by: Netflix, Inc
Differential Revision: https://reviews.freebsd.org/D4609
separate driver. Add support for activating clock and hwreset resources
for these devices when the EXT_RESOURCES option is present.
Reviewed by: andrew, mmel, Emmanuel Vadot <manu@bidouilliste.com>
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D5749
support frameworks (i.e. clk/regulators/tsensors/fuses...).
It provides simple unified consumers interface for manipulations with
phy (USB/SATA/PCIe) resources.
support frameworks(i.e. clk/reset/phy/tsensors/fuses...).
The framework is still far from perfect and probably doesn't have stable
interface yet, but we want to start testing it on more real boards and
different architectures.
improve cancellation robustness.
Introduce a new file operation, fo_aio_queue, which is responsible for
queueing and completing an asynchronous I/O request for a given file.
The AIO subystem now exports library of routines to manipulate AIO
requests as well as the ability to run a handler function in the
"default" pool of AIO daemons to service a request.
A default implementation for file types which do not include an
fo_aio_queue method queues requests to the "default" pool invoking the
fo_read or fo_write methods as before.
The AIO subsystem permits file types to install a private "cancel"
routine when a request is queued to permit safe dequeueing and cleanup
of cancelled requests.
Sockets now use their own pool of AIO daemons and service per-socket
requests in FIFO order. Socket requests will not block indefinitely
permitting timely cancellation of all requests.
Due to the now-tight coupling of the AIO subsystem with file types,
the AIO subsystem is now a standard part of all kernels. The VFS_AIO
kernel option and aio.ko module are gone.
Many file types may block indefinitely in their fo_read or fo_write
callbacks resulting in a hung AIO daemon. This can result in hung
user processes (when processes attempt to cancel all outstanding
requests during exit) or a hung system. To protect against this, AIO
requests are only permitted for known "safe" files by default. AIO
requests for all file types can be enabled by setting the new
vfs.aio.enable_usafe sysctl to a non-zero value. The AIO tests have
been updated to skip operations on unsafe file types if the sysctl is
zero.
Currently, AIO requests on sockets and raw disks are considered safe
and are enabled by default. aio_mlock() is also enabled by default.
Reviewed by: cem, jilles
Discussed with: kib (earlier version)
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D5289
These firmwares were obtained from the beta "Chelsio T5/T4 Unified Wire
v2.12.0.2 for Linux" release. Changes since last release are listed in the
"Release Notes" accompanying the beta release and are copy-pasted here as well.
The plan is to have only GA'd firmwares in any -STABLE FreeBSD branch so I'll
MFC this (after 2 months) only if it ends up in a GA release.
================================================================================
================================================================================
22.1. T5 Firmware
+++++++++++++++++++++++++++++++++
Version : 1.15.28.0
Date : 02/29/2016
================================================================================
FIXES
-----
BASE:
- Fixed an issue in FW_RSS_VI_CONFIG_CMD handling where the default ingress
queue was ignored.
- Fixed an issue where adapter failed to load fw by adjusting DRAM frequency.
- Fixed an issue in watchdog which was causing VM bring-up failure after
reboot.
- Fixed 40G link failures with some switches when auto-negotiation enabled.
- Fixed to improve on link bring-up time.
- Per port buffer groups size doubled to improve performance.
- Fixed an issue where bogus d3hot bits were set causing traffic stall.
- Fixed an issue where sometimes adapter was not seen after reboot.
- Fixed an issue where iWARP was crashing in conjunction with traffic
management.
- Fixed an issue where link failed to come up after removing twinax cable and
inserting optical module.
OFLD
- Fixed a potential iSCSI data corruption issue by disabling RxFragEn flag.
FOiSCSI
- Fixed an issue in recovery path where connection was getting closed before
recovery processing was done.
- Fixed an issue in TCP port reuse.
- Fixed an issue in recovery path when large number (>64) of iSCSI connections
were in use.
- Returned ENETUNREACH if IP was not been provisioned yet and driver tried to
use given inerface.
ENHANCEMENTS
------------
BASE:
- Added new interface to program DCA settings in SGE contexts; allow 32-byte
IQE size
- Added PTP interface fw_ptp_ts to support PTP Frequeny and Offset adjustment.
- Added MPS raw interface.
ETH:
- New mailbox command FW_DCB_IEEE_CMD api added for IEEE dcbx.
OFLD:
- WR opcode is returned to host in cqe error response.
================================================================================
================================================================================
22.2. T4 Firmware
+++++++++++++++++
Version : 1.15.28.0
Date : 02/29/2016
================================================================================
FIXES
-----
BASE:
- Fixed an issue in FW_RSS_VI_CONFIG_CMD handling where default ingress queue
was ignored.
- Fixed an issue in watchdog which was causing VM bring-up failure after
reboot.
- Per port buffer groups size doubled to improve performance.
- Fixed an issue where iWARP was crashing in conjunction with traffic
management.
FOiSCSI:
- Fixed an issue in recovery path where connection was getting closed before
recovery processing was done.
- Fixed an issue in TCP port reuse.
- Fixed an issue in recovery path when large number (>64) of iSCSI connections
were in use.
- Returned ENETUNREACH if IP had not been provisioned yet and driver tried to
use given inerface.
ENHANCEMENTS
------------
BASE:
- Added MPS raw interface.
ETH:
- New mailbox command FW_DCB_IEEE_CMD api added for IEEE dcbx.
================================================================================
Obtained from: Chelsio Communications
MFC after: 2 months
Sponsored by: Chelsio Communications
and geom_uncompress(4):
1. mkuzip(8):
- Proper support for eliminating all-zero blocks when compressing an
image. This feature is already supported by the geom_uzip(4) module
and CLOOP format in general, so it's just a matter of making mkuzip(8)
match. It should be noted, however that this feature while it sounds
great, results in very slight improvement in the overall compression
ratio, since compressing default 16k all-zero block produces only 39
bytes compressed output block, which is 99.8% compression ratio. With
typical average compression ratio of amd64 binaries and data being
around 60-70% the difference between 99.8% and 100.0% is not that
great further diluted by the ratio of number of zero blocks in the
uncompressed image to the overall number of blocks being less than
0.5 (typically). However, this may be important from performance
standpoint, so that kernel are not spinning its wheels decompressing
those empty blocks every time this zero region is read. It could also
be important when you create huge image mostly filled with zero
blocks for testing purposes.
- New feature allowing to de-duplicate output image. It turns out that
if you twist CLOOP format a bit you can do that as well. And unlike
zero-blocks elimination, this gives a noticeable improvement in the
overall compression ratio, reducing output image by something like
3-4% on my test UFS2 3GB image consisting of full FreeBSD base system
plus some of the packages (openjdk, apache etc), about 2.3GB worth of
file data (800+MB compressed). The only caveat is that images created
with this feature "on" would not work on older versions of FeeBSDxi
kernel, hence it's turned off by default.
- provide options to control both features and document them in manual
page.
- merge in all relevant LZMA compression support from the mkulzma(8),
add new option to select between both.
- switch license from ad-hoc beerware into standard 2-clause BSD.
2. geom_uzip(4):
- implement support for de-duplicated images;
- optimize some code paths to handle "all-zero" blocks without reading
any compressed data;
- beef up manual page to explain that geom_uzip(4) is not limited only
to md(4) images. The compressed data can be written to the block
device and accessed directly via magic of GEOM(4) and devfs(4),
including to mount root fs from a compressed drive.
- convert debug log code from being compiled in conditionally into
being present all the time and provide two sysctls to turn it on or
off. Due to intended use of the module, it can be used in
environments where there may not be a luxury to put new kernel with
debug code enabled. Having those options handy allows debug issues
without as much problem by just having access to serial console or
network shell access to a box/appliance. The resulting additional
CPU cycles are just few int comparisons and branches, and those are
minuscule when compared to data decompression which is the main
feature of the module.
- hopefully improve robustness and resiliency of the geom_uzip(4) by
performing some of the data validation / range checking on the TOC
entries and rejecting to attach to an image if those checks fail.
- merge in all relevant LZMA decompression support from the
geom_uncompress(4), enable automatically when appropriate format is
indicated in the header.
- move compilation work into its own worker thread so that it does not
clog g_up. This allows multiple instances work in parallel utilizing
smp cores.
- document new knobs in the manual page.
Reviewed by: adrian
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D5333
Extract common code from PowerPC's ofw_pci
Import portions of the PowerPC OF PCI implementation into
new file "ofw_pci.c", common for other platforms. The files ofw_pci.c and
ofw_pci.h from sys/powerpc/ofw no longer exist. All required declarations
are moved to sys/dev/ofw/ofw_pci.h.
This creates a new ofw_pci_write_ivar() function and modifies
ofw_pci_nranges(), ofw_pci_read_ivar(), ofw_pci_route_interrupt()
methods.
Most functions contain existing ppc implementations in the majority
unchanged. Now there is no need to have multiple identical copies
of methods for various architectures.
Submitted by: Marcin Mazurek <mma@semihalf.com>
Obtained from: Semihalf
Sponsored by: Annapurna Labs
Reviewed by: jhibbits, mmel
Differential Revision: https://reviews.freebsd.org/D4879
This needs to return to the drawing board as it breaks both
PowerPC and Sparc64 build.
Pointed out by: jhibbits
Import portions of the PowerPC OF PCI implementation into
new file "ofw_pci.c", common for other platforms. The files ofw_pci.c and
ofw_pci.h from sys/powerpc/ofw no longer exist. All required declarations
are moved to sys/dev/ofw/ofw_pci.h.
This creates a new ofw_pci_write_ivar() function and modifies
ofw_pci_nranges(), ofw_pci_read_ivar(), ofw_pci_route_interrupt() methods.
Most functions contain existing ppc implementations in the majority
unchanged. Now there is no need to have multiple identical copies
of methods for various architectures.
Submitted by: Marcin Mazurek <mma@semihalf.com>
Obtained from: Semihalf
Sponsored by: Annapurna Labs
Reviewed by: jhibbits, mmel
Differential Revision: https://reviews.freebsd.org/D4879
support frameworks (i.e. regulators/phy/tsensors/fuses...).
It provides simple unified consumers interface for manipulations with
on-chip resets.
Reviewed by: ian, imp (paritaly)
support frameworks(i.e. reset/regulators/phy/tsensors/fuses...).
The clock framework significantly simplifies handling of complex clock
structures found in modern SoCs. It provides the unified consumers
interface, holds and manages actual clock topology, frequency and gating.
It's tested on three different ARM boards (Nvidia Tegra TK1, Inforce 6410 and
Odroid XU2) and on one MIPS board (Creator Ci20) by kan@.
The framework is still far from perfect and probably doesn't have stable
interface yet, but we want to start testing it on more real boards and
different architectures.
Reviewed by: ian, kan (earlier version)
separate file. Claim my copyright.
- Provide more comments, better function and structure names.
- Sort out unneeded includes from resulting two files.
No functional changes.
The htree dir_index is perhaps one of the most characteristic
features of the linux ext3 implementation. It was removed
in r281670, due to repeated bug reports.
Damjan Jovanic detected and fixed three bugs and did some
stress testing by building Apache OpenOffice on top of it
so it is now in good shape to bring back.
Differential Revision: https://reviews.freebsd.org/D5007
Submitted by: Damjan Jovanovic
Reviewed by: pfg
Tested by: pho
Relnotes: Yes
MFC after: 2 months (only 10.x)
The upcoming GELI support in the loader reuses parts of this code
Some ifdefs are added, and some code is moved outside of existing ifdefs
The HMAC parts of GELI are broken out into their own file, to separate
them from the kernel crypto/openssl dependant parts that are replaced
in the boot code.
Passed the GELI regression suite (tools/regression/geom/eli)
Files=20 Tests=14996
Result: PASS
Reviewed by: pjd, delphij
MFC after: 1 week
Sponsored by: ScaleEngine Inc.
Differential Revision: https://reviews.freebsd.org/D4699
cperciva's libmd implementation is 5-30% faster
The same was done for SHA256 previously in r263218
cperciva's implementation was lacking SHA-384 which I implemented, validated against OpenSSL and the NIST documentation
Extend sbin/md5 to create sha384(1)
Chase dependancies on sys/crypto/sha2/sha2.{c,h} and replace them with sha512{c.c,.h}
Reviewed by: cperciva, des, delphij
Approved by: secteam, bapt (mentor)
MFC after: 2 weeks
Sponsored by: ScaleEngine Inc.
Differential Revision: https://reviews.freebsd.org/D3929
The mdio driver interface is generally useful for devices that require
MDIO without the full MII bus interface. This lifts the driver/interface
out of etherswitch(4), and adds a mdio(4) man page.
Submitted by: Landon Fuller <landon@landonf.org>
Differential Revision: https://reviews.freebsd.org/D4606
TFO is disabled by default in the kernel build. See the top comment
in sys/netinet/tcp_fastopen.c for implementation particulars.
Reviewed by: gnn, jch, stas
MFC after: 3 days
Sponsored by: Verisign, Inc.
Differential Revision: https://reviews.freebsd.org/D4350
Add support for two new devices: X552 SFP+ 10 GbE, and the single port
version of X550T.
Submitted by: erj
Reviewed by: gnn
Sponsored by: Intel Corporation
Differential Revision: https://reviews.freebsd.org/D4186
into a new function that other platforms can share.
This creates a new ofw_reg_to_paddr() function (in a new ofw_subr.c file)
that contains most of the existing ppc implementation, mostly unchanged.
The ppc code now calls the new MI code from the MD code, then creates a
ppc-specific bus_space mapping from the results. The new arm implementation
does the same in an arm-specific way.
This also moves the declaration of OF_decode_addr() from ofw_machdep.h to
openfirm.h, except on sparc64 which uses a different function signature.
This will help all FDT platforms to set up early console access using
OF_decode_addr().
Vast majority of rtalloc(9) users require only basic info from
route table (e.g. "does the rtentry interface match with the interface
I have?". "what is the MTU?", "Give me the IPv4 source address to use",
etc..).
Instead of hand-rolling lookups, checking if rtentry is up, valid,
dealing with IPv6 mtu, finding "address" ifp (almost never done right),
provide easy-to-use API hiding all the complexity and returning the
needed info into small on-stack structure.
This change also helps hiding route subsystem internals (locking, direct
rtentry accesses).
Additionaly, using this API improves lookup performance since rtentry is not
locked.
(This is safe, since all the rtentry changes happens under both radix WLOCK
and rtentry WLOCK).
Sponsored by: Yandex LLC
IPv4/IPv6 checksum offloading and VLAN tag insertion/stripping.
Since uether doesn't provide a way to announce driver specific offload
capabilities to upper stack, checksum offloading support needs more work
and will be done in the future.
Special thanks to Hayes Wang from RealTek who gave input.
Use hhook(9) framework to achieve ability of loading and unloading
if_enc(4) kernel module. INET and INET6 code on initialization registers
two helper hooks points in the kernel. if_enc(4) module uses these helper
hook points and registers its hooks. IPSEC code uses these hhook points
to call helper hooks implemented in if_enc(4).
This should be a big no-op pass; and reduces the size of if_ath.c.
I'm hopefully soon going to take a whack at the USB support for ath(4)
and this'll require some reuse of the busdma memory code.
default and add a manual page for mlx5en. The mlx5 module contains
shared code for both infiniband and ethernet. The mlx5en module
contains specific code for ethernet functionality only. A mlx5ib
module is in the works for infiniband support.
Supported hardware:
- ConnectX-4: 10/20/25/40/50/56/100Gb/s speeds.
- ConnectX-4 LX: 10/25/40/50Gb/s speeds (low power consumption)
Refer to the mlx5en(4) manual page for a comprehensive list.
The team porting the mlx5 driver(s) to FreeBSD:
- Hans Petter Selasky <hselasky@freebsd.org>
- Oded Shanoon <odeds@mellanox.com>
- Meny Yossefi <menyy@mellanox.com>
- Shany Michaely <shanim@mellanox.com>
- Shahar Klein <shahark@mellanox.com>
- Daria Genzel <dariaz@mellanox.com>
- Mark Bloch <markb@mellanox.com>
Differential Revision: https://reviews.freebsd.org/D4163
Submitted by: Mark Block <markb@mellanox.com>
Sponsored by: Mellanox Technologies
Reviewed by: gnn @
MFC after: 3 days
- Move all files related to the LinuxKPI into sys/compat/linuxkpi and
its subfolders.
- Update sys/conf/files and some Makefiles to use new file locations.
- Added description of COMPAT_LINUXKPI to sys/conf/NOTES which in turn
adds the LinuxKPI to all LINT builds.
- The LinuxKPI can be added to the kernel by setting the
COMPAT_LINUXKPI option. The OFED kernel option no longer builds the
LinuxKPI into the kernel. This was done to keep the build rules for
the LinuxKPI in sys/conf/files simple.
- Extend the LinuxKPI module to include support for USB by moving the
Linux USB compat from usb.ko to linuxkpi.ko.
- Bump the FreeBSD_version.
- A universe kernel build has been done.
Reviewed by: np @ (cxgb and cxgbe related changes only)
Sponsored by: Mellanox Technologies
This commit introduces support for etherswitch devices that utilize SMI as
a way of accessing its registers. SMI register is located in address space
of mge -- access to it was exported through MDIO interface.
Attachment functions were enhanced so as to ensure proper initialisation
in both cases: 1) PHYs attached directly to mge, 2) PHYs attached to
switch device and switch attached to mge. Attachment of etherswitch device
depends on dts entry with compatible="mrvl,sw" property. If none is found,
typical PHY attachment procedure follows.
In case of switch attached, PHYs' status and configuration is accessible
via etherswitchcfg, and ifconfig shows always-up, non-configurable mge
interfaces.
Due to the fact that there may be simultaneous accessess to SMI
registers (e.g. from PHY attached to one of mge instances and switch
to the other), SMI access interlock was added. It is SX lock,
because sleep ability is necessary -- busy-waiting would result
in poor performance due to long delays required by hardware.
Underlying switch driver is obliged to use sleepable locks as well.
Reviewed by: adrian
Obtained from: Semihalf
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Differential revision: https://reviews.freebsd.org/D3900
In order to make it easier to support CloudABI on ARM64, move out all of
the bits from the AMD64 cloudabi_sysvec.c into a new file
cloudabi_module.c that would otherwise remain identical. This reduces
the AMD64 specific code to just ~160 lines.
Reviewed by: kib
Differential Revision: https://reviews.freebsd.org/D3974
packets and/or state transitions from each TCP socket. That would help with
narrowing down certain problems we see in the field that are hard to reproduce
without understanding the history of how we got into a certain state. This
change provides just that.
It saves copies of the last N packets in a list in the tcpcb. When the tcpcb is
destroyed, the list is freed. I thought this was likely to be more
performance-friendly than saving copies of the tcpcb. Plus, with the packets,
you should be able to reverse-engineer what happened to the tcpcb.
To enable the feature, you will need to compile a kernel with the TCPPCAP
option. Even then, the feature defaults to being deactivated. You can activate
it by setting a positive value for the number of captured packets. You can do
that on either a global basis or on a per-socket basis (via a setsockopt call).
There is no way to get the packets out of the kernel other than using kmem or
getting a coredump. I thought that would help some of the legal/privacy concerns
regarding such a feature. However, it should be possible to add a future effort
to export them in PCAP format.
I tested this at low scale, and found that there were no mbuf leaks and the peak
mbuf usage appeared to be unchanged with and without the feature.
The main performance concern I can envision is the number of mbufs that would be
used on systems with a large number of sockets. If you save five packets per
direction per socket and have 3,000 sockets, that will consume at least 30,000
mbufs just to keep these packets. I tried to reduce the concerns associated with
this by limiting the number of clusters (not mbufs) that could be used for this
feature. Again, in my testing, that appears to work correctly.
Differential Revision: D3100
Submitted by: Jonathan Looney <jlooney at juniper dot net>
Reviewed by: gnn, hiren
The current Xen console driver is crashing very quickly when using it on
an ARM guest. This is because the console lock is recursive and it may
lead to recursion on the tty lock and/or corrupt the ring pointer.
Furthermore, the console lock is not always taken where it should be and has
to be released too early because of the way the console has been designed.
Over the years, code has been modified to support various new features but
the driver has not been reworked.
This new driver has been rewritten with the idea of only having a small set
of specific function to write either via the shared ring or the hypercall
interface.
Note that HVM support has been left aside for now because it requires
additional features which are not yet supported. A follow-up patch will be
sent with HVM guest support.
List of items that may be good to have but not mandatory:
- Avoid to flush for each character written when using the tty
- Support multiple consoles
Submitted by: Julien Grall <julien.grall@citrix.com>
Reviewed by: royger
Differential Revision: https://reviews.freebsd.org/D3698
Sponsored by: Citrix Systems R&D
CTL HA functionality was originally implemented by Copan many years ago,
but large part of the sources was never published. This change includes
clean room implementation of the missing code and fixes for many bugs.
This code supports dual-node HA with ALUA in four modes:
- Active/Unavailable without interlink between nodes;
- Active/Standby with second node handling only basic LUN discovery and
reservation, synchronizing with the first node through the interlink;
- Active/Active with both nodes processing commands and accessing the
backing storage, synchronizing with the first node through the interlink;
- Active/Active with second node working as proxy, transfering all
commands to the first node for execution through the interlink.
Unlike original Copan's implementation, depending on specific hardware,
this code uses simple custom TCP-based protocol for interlink. It has
no authentication, so it should never be enabled on public interfaces.
The code may still need some polishing, but generally it is functional.
Relnotes: yes
Sponsored by: iXsystems, Inc.
only gpiobus configured via FDT is supported. Bus enumeration is
supported. Devices are created for each device found. 1-Wire
temperature controllers are supported, but other drivers could be
written. Temperatures are polled and reported via a sysctl. Errors
are reported via sysctl counters. Mis-wired bus detection is included
for more trouble shooting. See ow(4), owc(4) and ow_temp(4) for
details of what's supported and known issues.
This has been tested on Raspberry Pi-B, Pi2 and Beagle Bone Black
with up to 7 devices.
Differential Revision: https://reviews.freebsd.org/D2956
Relnotes: yes
MFC after: 2 weeks
Reviewed by: loos@ (with many insightful comments)
CoDel is a parameterless queue discipline that handles variable bandwidth
and RTT.
It can be used as the single queue discipline on an interface or as a sub
discipline of existing queue disciplines such as PRIQ, CBQ, HFSC, FAIRQ.
Differential Revision: https://reviews.freebsd.org/D3272
Reviewd by: rpaulo, gnn (previous version)
Obtained from: pfSense
Sponsored by: Rubicon Communications (Netgate)
This driver allows read the software reset switch state and control the
status LEDs.
The GPIO pins have their direction (input/output) locked down to prevent
possible short circuits.
Note that most people get a reset button that is a hardware reset. The
software reset button is available on boards from Netgate.
Sponsored by: Rubicon Communications (Netgate)
if desired.
Retire randomdev_none.c and introduce random_infra.c for resident
infrastructure. Completely stub out random(4) calls in the "without
DEV_RANDOM" case.
Add RANDOM_LOADABLE option to allow loadable Yarrow/Fortuna/LocallyWritten
algorithm. Add a skeleton "other" algorithm framework for folks
to add their own processing code. NIST, anyone?
Retire the RANDOM_DUMMY option.
Build modules for Yarrow, Fortuna and "other".
Use atomics for the live entropy rate-tracking.
Convert ints to bools for the 'seeded' logic.
Move _write() function from the algorithm-specific areas to randomdev.c
Get rid of reseed() function - it is unused.
Tidy up the opt_*.h includes.
Update documentation for random(4) modules.
Fix test program (reviewers, please leave this).
Differential Revision: https://reviews.freebsd.org/D3354
Reviewed by: wblock,delphij,jmg,bjk
Approved by: so (/dev/random blanket)
It has nothing to share with too huge ctl.c other then device descriptor,
but even that may be counted as design error that may be fixed later.
At some point we may even want to have several ioctl ports.
Its idea was to be a simple initiator and execute several commands from
kernel level, but FreeBSD never had consumer for that functionality,
while its implementation polluted many unrelated places..
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Richard Elling <richard.elling@richardelling.com>
Approved by: Dan McDonald <danmcd@omniti.com>
Author: Prakash Surya <prakash.surya@delphix.com>
illumos/illumos-gate@244781f10d
This patch attempts to reduce lock contention on the current arc_state_t
mutexes. These mutexes are used liberally to protect the number of LRU
lists within the ARC (e.g. ARC_mru, ARC_mfu, etc). The granularity at
which these locks are acquired has been shown to greatly affect the
performance of highly concurrent, cached workloads.
changes in the firmwares since 1.11.27.0 are listed here (straight copy-paste
from the "Release Notes.txt" accompanying the Chelsio Unified Wire 2.11.1.0
release on the website).
22.1. T5 Firmware
+++++++++++++++++++++++++++++++++
Version : 1.14.4.0
Date : 08/05/2015
================================================================================
FIXES
-----
BASE:
- Fixes a potential data path hang by properly programming PMTX congestion
threshold settings.
- Fixes a potential initialization error when accessing a configuration file
stored on the flash.
- Fixes a regression where SGE resources can be miss-sized if iWARP is disabled.
ETH:
- Fixes a timing issue that would prevent CR4 links from coming up with some
switches.
FOFCoE:
- Defers fcoe linkdown mailbox command handling till LOGO is sent.
- Updates vlan prio for all outstanding IOs during dcbx update.
ENHANCEMENTS
------------
BASE:
- Adds support for PAUSE OFF watchdog.
- Reports devlog access information in PCIE_FW_PF register 7.
ETH:
- Enhances segmentation offload to include VxLAN and Geneve.
- Adds PTP support.
- Adds new interface to allow the driver to query the VI rss table base
addresses.
- Allows the driver to program the SGE ingrext contxt CongDrop field.
OFLD:
- Adds new interface for the driver to specify offloaded connections TCP snd
and rcv scale factors.
iSCSI:
- Adds support for iscsi segmentatation offload (ISO).
- Adds support for iscsi t10-dif offload.
FOiSCSI:
- Sets FORCE_BIT for cut through processing for FOiSCSI.
FOFCoE:
- Adds support for FCoE BB6.
- Improves WRITE performance.
================================================================================
================================================================================
Version : 1.13.32.0
Date : 03/25/2015
================================================================================
FIXES
-----
BASE:
- Fixes FW_CAPS_CONFIG_CMD return value on error (was positive instead of
negative)
- Fixes FW_PARAMS_PARAM_DEV_FLOWC_BUFFIFO_SZ indication (was wrong on certain
adapter configurations)
- Fixes config file based PL_TIMEOUT register programming
ETH:
- Fixes a potential EO UDP SEG header corruption
- Fixes an issue where 1000Base-X was not enabled correctly when using QSA
modules
OFLD:
- Fixes timeout issue with half-open connections
- Fixes FW_FLOWC_WR processing when state is set to finwait1
FOFCoE:
- Fixes fcoe xchg leaks in linkdown/peer down path
- Fixes cleanup in FCoE linkdown and fixed buf timer flowid abuse
- Fixes fw crash by clearing fcf flowc during bye
FOiSCSI:
- Don't create a new tcp socket if ERL0 attempt has timed out.
ENHANCEMENTS
------------
BASE:
- Adds support for VFs on PFs 4 to 7
- Adds support for QPs/CQs on any physical and virtual function
ETH:
- Stops sending LACP frames on loopback interface
- Adds an AUTOEQU indication to CPL_SGE_EGR_UPDATE
- Adds support for CR4 links (BEAN/AEC on 40G TwinAx cables)
OFLD:
- Improves default settings of LAN and CLUSTER TCP timer settings
- Sends Negative Advice CPLs to software
FOISCSI:
- Adds IPv6 support for foiscsi. Keeps backward compatibility with
old foiscsi drivers which doesn't support ipv6.
FOFCoE:
- Added fcoe debug support in flowc dump
================================================================================
================================================================================
Version : 1.12.25.0
Date : 10/22/2014
================================================================================
FIXES
-----
BASE:
- Improves precision of the Weight Round Robing Traffic Management Algorithm
- Fixes an issue where the link would intermittently fail to come up
- Fixes an issue where adapters with an external PHY couldn't run at 100Mbps
- Fixes an issue where active optical cables were not recognized
- Fixes link advertising issues on T520-BT (speed and pause frames) that would
cause the link to negotiate unexpected settings
- Forces link restart when auto-negotiation is disabled
- Fix an issue where pause frames wouldn't be fully disabled even if requested
ETH:
- Fixes NVGRE Segmentation Offload network header generation.
DCBX:
- Fixes an issue where some settings were not being sent to the switch
correctly
- Fixes an issue where back-to-back DCBX port updates could get overwritten by
FW
- Fixes a firmware crash on DCBX APP information request before link up
FOiSCSI:
- Fixes abort task leak in tmf response handling
- Fixes TCP RST handling while in iSCSI ERL0
- Fixes a firmware crash on BYE without INIT
ENHANCEMENTS
-------------
BASE:
- Adds link partner settings reporting when available
- Adds QSA support (in conjunction with QSA VPD)
- Adds T520-BT LED support
- Reports NOTSUPPORTED for modules with an unhandled identifier
DCBX:
- Adds version reporting (indicating which version FW is trying to negotiate)
- Adds IEEE support
- Reports LLDP time outs
FOiSCSI:
- Add support for multiple iSCSI DDP client
- Sends DHCP renew request when lease expires
================================================================================
22.2. T4 Firmware
+++++++++++++++++
Version : 1.14.4.0
Date : 08/05/2015
================================================================================
FIXES
-----
BASE:
- Fixes a potential initialization error when accessing a configuration file
stored on the flash.
- Initialize PCIE_DBG_INDIR_REQ.Enable to 0, as hardware failed to do so and
register dumps could result in errors.
ETH:
- Fixes an issue that sometimes prevented the link from coming up in CR adapters.
ENHANCEMENTS
------------
BASE:
- Adds support for PAUSE OFF watchdog.
- Reports devlog access information in PCIE_FW_PF register 7.
ETH:
- Adds new interface to allow the driver to query the VI rss table base
addresses.
OFLD:
- Adds new interface for the driver to specify offloaded connections TCP snd
and rcv scale factors.
================================================================================
================================================================================
Version : 1.13.32.0
Date : 03/25/2015
================================================================================
FIXES
-----
BASE:
- Fixes FW_CAPS_CONFIG_CMD return value on error (was positive instead of
negative)
- Fixes FW_PARAMS_PARAM_DEV_FLOWC_BUFFIFO_SZ indication (was wrong on certain
adapter configurations)
- Fixes config file based PL_TIMEOUT register programming
ETH:
- Fixes a potential EO UDP SEG header corruption
OFLD:
- Fixes timeout issue with half-open connections
- Fixes FW_FLOWC_WR processing when state is set to finwait1
FOiSCSI:
- Don't create a new tcp socket if ERL0 attempt has timed out.
ENHANCEMENTS
------------
ETH:
- Stops sending LACP frames on loopback interface
- Adds an AUTOEQU indication to CPL_SGE_EGR_UPDATE
OFLD:
- Improves default settings of LAN and CLUSTER TCP timer settings
- Sends Negative Advice CPLs to software
================================================================================
================================================================================
Version : 1.12.25.0
Date : 10/22/2014
================================================================================
FIXES
-----
BASE:
- Improves precision of the Weight Round Robing Traffic Management Algorithm
- Forces link restart when auto-negotiation is disabled
- Fix an issue where pause frames wouldn't be fully disabled even if requested
DCBX:
- Fixes an issue where some settings were not being sent to the switch
correctly
- Fixes an issue where back-to-back DCBX port updates could get overwritten by
FW
- Fixes a firmware crash on DCBX APP information request before link up
FOiSCSI:
- Fixes abort task leak in tmf response handling
- Fixes TCP RST handling while in iSCSI ERL0
- Fixes a firmware crash on BYE without INIT
ENHANCEMENTS
------------
BASE:
- Adds link partner settings reporting when available
- Firmware now reports NOTSUPPORTED for modules with an unhandled identifier
DCBX:
- Adds version reporting (indicating which version FW is trying to negotiate)
- Adds IEEE support
- Reports LLDP time outs
FOiSCSI:
- Adds support for multiple iSCSI DDP clients
- Sends DHCP renew request when lease expires
================================================================================
Obtained from: Chelsio Communications
MFC after: 2 weeks
Sponsored by: Chelsio Communications
Brightness is controlled through sysctl dev.gpiobacklight.X.brightness:
- any value greater than 0: backlight is on
- any value less than or equal to 0: backlight is off
FDT bindings docs in Linux tree:
Documentation/devicetree/bindings/video/backlight/gpio-backlight.txt
This feature is inspired by another Unix-alike OS commonly found on
airplane headrests.
A number of beasties[0] are drawn at top of framebuffer during boot,
based on the number of active SMP CPUs[1]. Console buffer output
continues to scroll in the screen area below beastie(s)[2].
After some time[3] has passed, the beasties are erased leaving the
entire terminal for use.
Includes two 80x80 vga16 beastie graphics and an 80x80 vga16 orb
graphic. (The graphics are RLE compressed to save some space -- 3x 3200
bytes uncompressed, or 4208 compressed.)
[0]: The user may select the style of beastie with
kern.vt.splash_cpu_style=(0|1|2)
[1]: Or the number may be overridden with tunable kern.vt.splash_ncpu.
[2]: https://www.youtube.com/watch?v=UP2jizfr3_o
[3]: Configurable with kern.vt.splash_cpu_duration (seconds, def. 10).
Differential Revision: https://reviews.freebsd.org/D2181
Reviewed by: dumbbell, emaste
Approved by: markj (mentor)
MFC after: 2 weeks
in lockstat.ko. This means that lockstat probes now have typed arguments and
will utilize SDT probe hot-patching support when it arrives.
Reviewed by: gnn
Differential Revision: https://reviews.freebsd.org/D2993
Summary:
For CloudABI we need to put two things on the stack of new processes:
the argument data (a binary blob; not strings) and a startup data
structure. The startup data structure contains interesting things such
as a pointer to the ELF program header, the thread ID of the initial
thread, a stack smashing protection canary, and a pointer to the
argument data.
Fetching system call arguments and setting the return value is similar
to FreeBSD. The only differences are that system call 0 does not exist
and that we call into cloudabi_convert_errno() to convert the error
code. We also need this function in a couple of other places, so we'd
better reuse it here.
Reviewers: dchagin, kib
Reviewed By: kib
Subscribers: imp
Differential Revision: https://reviews.freebsd.org/D3098
This is based on work done by jeff@ and jhb@, as well as the numa.diff
patch that has been circulating when someone asks for first-touch NUMA
on -10 or -11.
* Introduce a simple set of VM policy and iterator types.
* tie the policy types into the vm_phys path for now, mirroring how
the initial first-touch allocation work was enabled.
* add syscalls to control changing thread and process defaults.
* add a global NUMA VM domain policy.
* implement a simple cascade policy order - if a thread policy exists, use it;
if a process policy exists, use it; use the default policy.
* processes inherit policies from their parent processes, threads inherit
policies from their parent threads.
* add a simple tool (numactl) to query and modify default thread/process
policities.
* add documentation for the new syscalls, for numa and for numactl.
* re-enable first touch NUMA again by default, as now policies can be
set in a variety of methods.
This is only relevant for very specific workloads.
This doesn't pretend to be a final NUMA solution.
The previous defaults in -HEAD (with MAXMEMDOM set) can be achieved by
'sysctl vm.default_policy=rr'.
This is only relevant if MAXMEMDOM is set to something other than 1.
Ie, if you're using GENERIC or a modified kernel with non-NUMA, then
this is a glorified no-op for you.
Thank you to Norse Corp for giving me access to rather large
(for FreeBSD!) NUMA machines in order to develop and verify this.
Thank you to Dell for providing me with dual socket sandybridge
and westmere v3 hardware to do NUMA development with.
Thank you to Scott Long at Netflix for providing me with access
to the two-socket, four-domain haswell v3 hardware.
Thank you to Peter Holm for running the stress testing suite
against the NUMA branch during various stages of development!
Tested:
* MIPS (regression testing; non-NUMA)
* i386 (regression testing; non-NUMA GENERIC)
* amd64 (regression testing; non-NUMA GENERIC)
* westmere, 2 socket (thankyou norse!)
* sandy bridge, 2 socket (thankyou dell!)
* ivy bridge, 2 socket (thankyou norse!)
* westmere-EX, 4 socket / 1TB RAM (thankyou norse!)
* haswell, 2 socket (thankyou norse!)
* haswell v3, 2 socket (thankyou dell)
* haswell v3, 2x18 core (thankyou scott long / netflix!)
* Peter Holm ran a stress test suite on this work and found one
issue, but has not been able to verify it (it doesn't look NUMA
related, and he only saw it once over many testing runs.)
* I've tested bhyve instances running in fixed NUMA domains and cpusets;
all seems to work correctly.
Verified:
* intel-pcm - pcm-numa.x and pcm-memory.x, whilst selecting different
NUMA policies for processes under test.
Review:
This was reviewed through phabricator (https://reviews.freebsd.org/D2559)
as well as privately and via emails to freebsd-arch@. The git history
with specific attributes is available at https://github.com/erikarn/freebsd/
in the NUMA branch (https://github.com/erikarn/freebsd/compare/local/adrian_numa_policy).
This has been reviewed by a number of people (stas, rpaulo, kib, ngie,
wblock) but not achieved a clear consensus. My hope is that with further
exposure and testing more functionality can be implemented and evaluated.
Notes:
* The VM doesn't handle unbalanced domains very well, and if you have an overly
unbalanced memory setup whilst under high memory pressure, VM page allocation
may fail leading to a kernel panic. This was a problem in the past, but it's
much more easily triggered now with these tools.
* This work only controls the path through vm_phys; it doesn't yet strongly/predictably
affect contigmalloc, KVA placement, UMA, etc. So, driver placement of memory
isn't really guaranteed in any way. That's next on my plate.
Sponsored by: Norse Corp, Inc.; Dell
CloudABI is a pure capability-based runtime environment for UNIX. It
works similar to Capsicum, except that processes already run in
capabilities mode on startup. All functionality that conflicts with this
model has been omitted, making it a compact binary interface that can be
supported by other operating systems without too much effort.
CloudABI is 'secure by default'; the idea is that it should be safe to
run arbitrary third-party binaries without requiring any explicit
hardware virtualization (Bhyve) or namespace virtualization (Jails). The
rights of an application are purely determined by the set of file
descriptors that you grant it on startup.
The datatypes and constants used by CloudABI's C library (cloudlibc) are
defined in separate files called syscalldefs_mi.h (pointer size
independent) and syscalldefs_md.h (pointer size dependent). We import
these files in sys/contrib/cloudabi and wrap around them in
cloudabi*_syscalldefs.h.
We then add stubs for all of the system calls in sys/compat/cloudabi or
sys/compat/cloudabi64, depending on whether the system call depends on
the pointer size. We only have nine system calls that depend on the
pointer size. If we ever want to support 32-bit binaries, we can simply
add sys/compat/cloudabi32 and implement these nine system calls again.
The next step is to send in code reviews for the individual system call
implementations, but also add a sysentvec, to allow CloudABI executabled
to be started through execve().
More information about CloudABI:
- GitHub: https://github.com/NuxiNL/cloudlibc
- Talk at BSDCan: https://www.youtube.com/watch?v=SVdF84x1EdA
Differential Revision: https://reviews.freebsd.org/D2848
Reviewed by: emaste, brooks
Obtained from: https://github.com/NuxiNL/freebsd
directory sys/contrib/libnv.
The goal of this operation is to NOT install header files which shouldn't
be used outside the nvlist library.
Approved by: pjd (mentor)
* GENERAL
- Update copyright.
- Make kernel options for RANDOM_YARROW and RANDOM_DUMMY. Set
neither to ON, which means we want Fortuna
- If there is no 'device random' in the kernel, there will be NO
random(4) device in the kernel, and the KERN_ARND sysctl will
return nothing. With RANDOM_DUMMY there will be a random(4) that
always blocks.
- Repair kern.arandom (KERN_ARND sysctl). The old version went
through arc4random(9) and was a bit weird.
- Adjust arc4random stirring a bit - the existing code looks a little
suspect.
- Fix the nasty pre- and post-read overloading by providing explictit
functions to do these tasks.
- Redo read_random(9) so as to duplicate random(4)'s read internals.
This makes it a first-class citizen rather than a hack.
- Move stuff out of locked regions when it does not need to be
there.
- Trim RANDOM_DEBUG printfs. Some are excess to requirement, some
behind boot verbose.
- Use SYSINIT to sequence the startup.
- Fix init/deinit sysctl stuff.
- Make relevant sysctls also tunables.
- Add different harvesting "styles" to allow for different requirements
(direct, queue, fast).
- Add harvesting of FFS atime events. This needs to be checked for
weighing down the FS code.
- Add harvesting of slab allocator events. This needs to be checked for
weighing down the allocator code.
- Fix the random(9) manpage.
- Loadable modules are not present for now. These will be re-engineered
when the dust settles.
- Use macros for locks.
- Fix comments.
* src/share/man/...
- Update the man pages.
* src/etc/...
- The startup/shutdown work is done in D2924.
* src/UPDATING
- Add UPDATING announcement.
* src/sys/dev/random/build.sh
- Add copyright.
- Add libz for unit tests.
* src/sys/dev/random/dummy.c
- Remove; no longer needed. Functionality incorporated into randomdev.*.
* live_entropy_sources.c live_entropy_sources.h
- Remove; content moved.
- move content to randomdev.[ch] and optimise.
* src/sys/dev/random/random_adaptors.c src/sys/dev/random/random_adaptors.h
- Remove; plugability is no longer used. Compile-time algorithm
selection is the way to go.
* src/sys/dev/random/random_harvestq.c src/sys/dev/random/random_harvestq.h
- Add early (re)boot-time randomness caching.
* src/sys/dev/random/randomdev_soft.c src/sys/dev/random/randomdev_soft.h
- Remove; no longer needed.
* src/sys/dev/random/uint128.h
- Provide a fake uint128_t; if a real one ever arrived, we can use
that instead. All that is needed here is N=0, N++, N==0, and some
localised trickery is used to manufacture a 128-bit 0ULLL.
* src/sys/dev/random/unit_test.c src/sys/dev/random/unit_test.h
- Improve unit tests; previously the testing human needed clairvoyance;
now the test will do a basic check of compressibility. Clairvoyant
talent is still a good idea.
- This is still a long way off a proper unit test.
* src/sys/dev/random/fortuna.c src/sys/dev/random/fortuna.h
- Improve messy union to just uint128_t.
- Remove unneeded 'static struct fortuna_start_cache'.
- Tighten up up arithmetic.
- Provide a method to allow eternal junk to be introduced; harden
it against blatant by compress/hashing.
- Assert that locks are held correctly.
- Fix the nasty pre- and post-read overloading by providing explictit
functions to do these tasks.
- Turn into self-sufficient module (no longer requires randomdev_soft.[ch])
* src/sys/dev/random/yarrow.c src/sys/dev/random/yarrow.h
- Improve messy union to just uint128_t.
- Remove unneeded 'staic struct start_cache'.
- Tighten up up arithmetic.
- Provide a method to allow eternal junk to be introduced; harden
it against blatant by compress/hashing.
- Assert that locks are held correctly.
- Fix the nasty pre- and post-read overloading by providing explictit
functions to do these tasks.
- Turn into self-sufficient module (no longer requires randomdev_soft.[ch])
- Fix some magic numbers elsewhere used as FAST and SLOW.
Differential Revision: https://reviews.freebsd.org/D2025
Reviewed by: vsevolod,delphij,rwatson,trasz,jmg
Approved by: so (delphij)
This will require for AArch64 as we dont have modules yet.
Sponsored by: HEIF5
Sponsored by: ARM Ltd.
Differential Revision: https://reviews.freebsd.org/D1997
Leaf drivers should not import the PCI bus interface to add IOV handling.
Instead, move the IOV client methods to a separate kobj interface.
Differential Revision: https://reviews.freebsd.org/D2584
Reviewed by: rstone
