The already-listed APMC0D0F ID belongs to the Ampere eMAG aarch64
platform, but ACPI support was not even built on aarch64.
Submitted by: Greg V <greg_unrelenting.technology>
Differential Revision: https://reviews.freebsd.org/D21059
of the TCP TS offset from taking the IP addresses and the TCP port
numbers into account to a version just taking only the IP addresses
into account. This works around broken middleboxes or endpoints.
The default is to keep the behaviour, which is also the behaviour
recommended in RFC 7323.
Reported by: devgs@ukr.net
Reviewed by: rrs@
MFC after: 2 weeks
Sponsored by: Netflix, Inc.
Differential Revision: https://reviews.freebsd.org/D20980
- Wrong order of casting and bit shift caused that enabling and disabling
queues didn't work properly for queues number larger than 32. Use literals
with right suffix instead.
- TX ring tail address was not updated during reinitiailzation of TX
structures. It could block sending traffic.
- Also remove unused variables 'eims' and 'active_queues'.
Submitted by: Krzysztof Galazka <krzysztof.galazka@intel.com>
Reviewed by: erj@
Sponsored by: Intel Corporation
Differential Revision: https://reviews.freebsd.org/D20826
Previously only some of the ID register fields were 64 bit. To allow
for a script to generate these mark them all 64 bit. To allow for their
use in assembly we need to use the UINT64_C macro via a new UL macro
to stop the lines from being too long.
MFC after: 1 week
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D20977
After r343631 pfil hooks are invoked in net_epoch_preempt section,
this allows to avoid extra locking. Add NET_EPOCH_ASSER() assertion
to each ipfw_bpf_*tap*() call to require to be called from inside
epoch section.
Use NET_EPOCH_WAIT() in ipfw_clone_destroy() to wait until it becomes
safe to free() ifnet. And use on-stack ifnet pointer in each
ipfw_bpf_*tap*() call to avoid NULL pointer dereference in case when
V_*log_if global variable will become NULL during ipfw_bpf_*tap*() call.
Sponsored by: Yandex LLC
While for ATA disks resize is even more rare situation than for SCSI, it
may happen in case of HPA or AMA being used. Make ATA XPT report minor
IDENTIFY DATA change to upper layers with AC_GETDEV_CHANGED, and ada(4)
periph driver handle that event, recalculating all the disk properties and
signalling resize to GEOM. Since ATA has no mechanism of UNIT ATTENTIONs,
like SCSI, it has no way to detect that something has changed. That is why
this functionality depends on explicit reprobe via XPT_REPROBE_LUN call.
MFC after: 2 weeks
Relnotes: yes
Sponsored by: iXsystems, Inc.
oldpvo is never explicitly NULL'd by moea64_pvo_enter(), so don't check for
NULL to do anything, only check error.
PR: 239372
Reported by: Francis Little
In principle this should not matter as it's a union and they point to
the same memory location but based on the code above we should be
accessing .sata and not .ata.
Submitted by: arichardson
Reviewed by: scottl, imp
Obtained from: CheriBSD
MFC after: 1 week
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D21002
o Add an experimental IOMMU support to xDMA framework
The BERI IOMMU device is the part of CHERI device-model project [1]. It
translates memory addresses for various BERI peripherals modelled in
software. It accepts FreeBSD/mips64 page directories format and manages
BERI TLB.
1. https://github.com/CTSRD-CHERI/device-model
Sponsored by: DARPA, AFRL
Summary:
Instead of searching for a PVO entry before adding, take advantage of
the fact that RB_INSERT() returns NULL if it inserts, and the existing entry if
an entry exists, without inserting a new entry. This saves an extra tree
traversal in the cases where the PVO does not exist.
Reviewed by: luporl
Differential Revision: https://reviews.freebsd.org/D20944
There are some explicit comparisions of refcount_release(9) result
with 0/1, which are fine.
Reviewed by: markj, mjg
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D21014
we should test ATTR_SW_DBM, not ATTR_AP_RW, to determine whether to set
PGA_WRITEABLE. In effect, we are currently setting PGA_WRITEABLE based on
whether the dirty bit is preset, not whether the mapping is writeable.
Correct this mistake.
Reviewed by: markj
X-MFC with: r350004
Differential Revision: https://reviews.freebsd.org/D21013
fget_unlocked() and fhold().
On sufficiently large machine, f_count can be legitimately very large,
e.g. malicious code can dup same fd up to the per-process
filedescriptors limit, and then fork as much as it can.
On some smaller machine, I see
kern.maxfilesperproc: 939132
kern.maxprocperuid: 34203
which already overflows u_int. More, the malicious code can create
transient references by sending fds over unix sockets.
I realized that this check is missed after reading
https://secfault-security.com/blog/FreeBSD-SA-1902.fd.html
Reviewed by: markj (previous version), mjg
Tested by: pho (previous version)
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D20947
where the page table entry was previously invalid. (Note that I did not
replace pmap_load_store() when it was followed by a TLB invalidation, even
if we are not using the return value from pmap_load_store().)
Correct an error in pmap_enter(). A test for determining when to set
PGA_WRITEABLE was always true, even if the mapping was read only.
In pmap_enter_l2(), when replacing an empty kernel page table page by a
superpage mapping, clear the old l2 entry and issue a TLB invalidation. My
reading of the ARM architecture manual leads me to believe that the TLB
could hold an intermediate entry referencing the empty kernel page table
page even though it contains no valid mappings.
Replace a couple direct uses of atomic_clear_64() by the new
pmap_clear_bits().
In a couple comments, replace the term "paging-structure caches", which is
an Intel-specific term for the caches that hold intermediate entries in the
page table, with wording that is more consistent with the ARM architecture
manual.
Reviewed by: markj
X-MFC after: r350004
Differential Revision: https://reviews.freebsd.org/D20998
features offered by the chips.
For 2127 and 2129 chips, fix the detection of when chip-init is needed. The
chip config needs to be reset whenever power was lost, but the logic was
wrong for 212x chips (it only worked for 8523). Now the "oscillator
stopped" bit rather than the power manager mode is used to detect startup
after powerfail.
For all chips, disable the clock output pin.
For chips that have a timestamp/tamper-monitor feature, turn off monitoring
of the timestamp trigger pin.
The 8523, 2127, and 2129 chips have a "power manager" feature that offers
several options. We've been using the default mode which enables
everything. Now the code sets the power manager options to
- direct-switch (when Vdd < Vbat, without extra threshold check)
- no battery monitor
- no external powerfail monitor
This reduces the current draw while running on battery from 1930nA to 880nA,
which should roughly double the lifespan of the battery under load.
Because battery checking is a nice thing to have, the code now does a check
at startup, and then once a day after that, instead of checking continuously
(but only actually reporting at startup). The battery check is now done by
setting the power manager back to default mode, sleeping briefly while it
makes a voltage measurement, then switching back to power-saving mode.
I would like to use the name vm_page_release() for a different purpose,
and vm_page_{import,release}() are local to vm_page.c.
Reviewed by: kib
MFC after: 1 week
EFSCFD (floating point single convert from double) emulation requires saving
the high word of the register, which uses SPE instructions. Enable the SPE
to avoid an SPV Unavailable exception.
MFC after: 1 week
Use 'struct bintime' instead of 'sbintime_t' to manage times in vPIT
to postpone rounding to final results rather than intermediate
results. In tests performed by Joyent, this reduced the error measured
by Linux guests by 59 ppm.
Smart OS bug: https://smartos.org/bugview/OS-6923
Submitted by: Patrick Mooney
Reviewed by: rgrimes
Obtained from: SmartOS / Joyent
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D20335
Add HWCAP support for arm64.
defines are the same as in Linux and a userland program can use
elf_aux_info to get the data.
We only save the common denominator for all cores in case the
big and little cluster have different support (this is known to
exists even if we don't support those SoCs in FreeBSD)
Differential Revision: https://reviews.freebsd.org/D17137
When sendmsg(2) sucessfully internalized one SCM_RIGHTS control
message, but failed to process some other control message later, both
file references and filedescent memory needs to be freed. This was not
done, only mbuf chain was freed.
Noted, test case written, reviewed by: markj
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D21000
entry, combining code currently in vm_map_unwire and
vm_map_wire_locked into a single function, called by each of them for
entries in transition.
Discussed with: kib, markj
Reviewed by: alc
Approved by: kib, markj (mentors, implicit)
Tested by: pho
Differential Revision: https://reviews.freebsd.org/D20833
AMA replaced HPA in ACS-3 specification. It allows to limit size of the
disk alike to HPA, but declares inaccessible data as indeterminate. One
of its practical use cases is to under-provision SATA SSDs for better
reliability and performance.
While there, fix HPA Security detection/reporting.
MFC after: 2 weeks
Relnotes: yes
Sponsored by: iXsystems, Inc.
While we print failure messages on the console, sometimes logs are lost or
overwhelmed. Keeping a count of how many times we've failed retriable commands
helps get a magnitude of the problem.
Retried commands can indicate a performance degredation of an nvme drive. Keep
track of the number of retries and report it out via sysctl, just like number of
commands an interrupts.
Also convert it to a bool. While the rest of the driver isn't yet bool clean,
this will help.
Reviewed by: cem@
Differential Revision: https://reviews.freebsd.org/D20988
The nvme drive dumps only the most relevant details about a command when it
fails. However, there are times this is not sufficient (such as debugging weird
issues for a new drive with a vendor). Setting hw.nvme.verbose_cmd_dump=1
in loader.conf will enable more complete debugging information about each
command that fails.
Reviewed by: rpokala
Sponsored by: Netflix
Differential Version: https://reviews.freebsd.org/D20988
These macros make places where we extract these easier to read. The shift and
mask stuff is also a bit tedious and error prone. Start with the CAP_LO and
CAP_HI registers since their scope is somewhat constrained. This is style
chagne only, no functional changes.
Reviewed by: chuck
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D20979
