Fix a bug which could cause panics in ad/atapi-interrupt.
Add support for UDMA66 on Promise Ultra/Fasttrak controllers.
Get rid of ATA_IGNORE_INTR, and introduce ATA_WAIT_INTR instead.
Add a delay in the dump routine in ata-disk.c, some controllers
seem to need this. Also dont use the timeout watchdog when dumping.
Disable DMA on ATAPI devices as default, add option ATA_ENABLE_ATAPI_DMA
for those that has HW that works.
Add support for some not-up-to-spec ATAPI devices that returns data
together with completition status on data moving cmd's.
"rw" argument, rather than hijacking B_{READ|WRITE}.
Fix two bugs (physio & cam) resulting by the confusion caused by this.
Submitted by: Tor.Egge@fast.no
Reviewed by: alc, ken (partly)
Merge the contents (less some trivial bordering the silly comments)
of <vm/vm_prot.h> and <vm/vm_inherit.h> into <vm/vm.h>. This puts
the #defines for the vm_inherit_t and vm_prot_t types next to their
typedefs.
This paves the road for the commit to follow shortly: change
useracc() to use VM_PROT_{READ|WRITE} rather than B_{READ|WRITE}
as argument.
test this support since I don't have the dongle for the card in
question and the dongle I have for my 3C589D doesn't seem to work on
it. I don't know if this is due to the damage I did to the 562 card
in transit from freebsdcon, or a mis-matched dongle...
Update AverMedia GPIO values
Submitted by: AverMedia
Add support for WinTV Theater Dolby Surround Sound DPL3518A chip
Submitted by: Frank Nobis <fn@radio-do.de>
Make PLL mode the default for Bt878s. You no longer need options BKTR_USE_PLL
pccard attachments must activate the resources they want to access.
ep didn't do this, so of course thee eeprom came back as busy. ed and
sio already did this. It was only due to a bug in the logic that the
probe succeeded. These problems have been fixed.
- Rip out all the static softc stuff and do softc allocation the right way.
- Rewrite most of the ISA code so that it provides a DEVICE_IDENTIFY
method to enumerate all non-PnP ISA devices.
This has the following consequences:
- No 'ep' devices may be hardwired.
- All hardwired devices will probably be detected twice.
By hardwired I mean:
device ep0 at isa? port 0x300 irq 10
- 'ep' devices are ordered by bus, slot, and then MAC address.
- Make 3c509B cards work in PnP mode. Yes, they really work.
- Convert over to using ifmedia for media selection. No more of this
lame 'linkX' stuff.
- Consolidate a lot of duplicated code.
- Make a stab at not breaking MII based PCCARD devices.
I doubt that the PCCARD stuff works any more than it did before my
changes but theres hope. My PCCARD hardware should arrive in a
week or so.
- Retreive the media settings from the card EEPROM rather than guessing.
I've got a 3c509-TPO that thinks its got an AUI port and if others
can report similar problems I'll write a bit of clever code that will
fix this but right now it works correctly on all but 1 card.
- Clean up a few things and make some cosmetic changes.
- Add myself as the MAINTAINER since nobody else wants to. I'm
in the best position to do this as I've got an example of most
of the cards:
EISA 3c579 bnc/aui
MCA 3c529 tp/aui
ISA 3c509 tpo
ISA-PnP 3c509B combo
If someone wants to send me a any cards I don't have I'd appriciate
it. Also welcome are 3c59x boards since I'll be folding if_vx and
if_ep at some point.
Shift to using the same queueing strategy that the amr driver uses.
Some simple tests indicate that we use about 2% of the CPU at around
500tps with the controller completely saturated with I/O.
the time spent at splbio(). We now avoid it unless we are actually
manipulating the command queues themselves. This doesn't improve
performance noticeably, but should improve concurrency somewhat.
(yet) compile and link. Renamed pcic back to pcic from pcicx, but
conditionalize its inclusion on pccard being included also. card is
the old and pccard is the new, which is a handy way to have both in
the tree at the same time.
Obtained from: newconfig project
More to follow...
incomplete and likely has problem. The code was originally pcmcia,
but I renamed it to pccard and made it compile on FreeBSD -current. I
converted SIMPLEQ to STAILQ as well as a few sc->dev.xname ->
device_printf changes. This is a green port of fairly mature code.
I derived this work from the FreeBSD newconfig project
(http://www.jp.freebsd.org/newconfig). Any problems with it are
likely introduced by me.
Obtained from: newconfig project
if_fe.c uses PCCARD_MODULE() and is part of GENERIC. I've #ifdef'ed out
the #include of "card.h" to hopefully disable pccard support in this
driver until it can be converted. I'm not positive this will fix make
release, but it can't possibly make it any worse than it is now.
I hope this stuff settles down soon.
yet, but that should be resolved shortly. Non memory mapped ed
devices should work, but I cannot test this since my only ed card is
memory mapped.
Submitted by: Matt Dodd <mdodd@freebsd.org>
I'm committing this from a laptop running this driver. Have only one
devclass for all ep devices (at least for pccard and eisa) so unit
numbering is sane. Might not work with both isa and non-isa devices
on the same system until ep is updated (Matt has some patches in the
pipeline which should resolve this, he wanted me to commit this so he
can resolve any conflicts against cvs rather than my patches).
Reviewed by: Matt Dodd <mdodd@freebsd.org>
by Peter Wemm, but I've not merged all the changes he sent to me yet.
This has not been reviewed by bde, so I'm committing to resolve any
issues he has with this when he returns from FreeBSD CON 99.
I've had four reports of this working for them. I've been able to
communicate to both my built in modem and a pccard modem with these
patches.
Been in production for 3 years now. Gives Instant Frame relay to if_sr
and if_ar drivers, and PPPOE support soon. See:
ftp://ftp.whistle.com/pub/archie/netgraph/index.html
for on-line manual pages.
Reviewed by: Doug Rabson (dfr@freebsd.org)
Obtained from: Whistle CVS tree
it has the same value on all platforms. Previously it was just under
3 seconds on x86 (typically hz<=128) and just under 1/3 of a second on
alpha (typically hz>=1024). This covers up a race between ad_interrupt()
and ad_timeout() which is being looked into.
reviewd by: sos
bootup. Somehow my backout of an abortaive attempt at shared
memory autoconfiguration included this line:
sc->mem_shared = 1;
Which is fairly important as it turns out.
Since I performed my pre-commit testing on a different box with a generic
NE2000 I didn't catch this. Pointy hat.
Put splbio protection around the main launch loop. We've seen cases where
the bottom half was cutting off the branch on which we're sitting.
Experienced-by: Michael Reifenberger <root@nihil.plaut.de>
have you is prototyped). Removed code versions in md struct- not used
any more. Allocate transfer dma maps and xflist stuff in mbxdmasetup based
upon isp->isp_maxcmds. Allow for multiple calls to mbxdmasetup (for
isp_reset cases).
file later. Do some pencil-sharpening types of minor changes. Change
how active commands are remembered (using new inline functions to get
handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as
outgoing mailbox 2 will tell you the f/w's notion of the max commands
that can be supported. Attempt to retrieve loop topology. Add in the
appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little
Endian machines but is needed for sparc (on other platforms)). Move
the temp port database we use to find out where things have moved to
after a LIP to the softc and off the kernel stack. Follow Qlogic's
hint and don't bother setting a tag for commands that don't have
this enabled (presumably the f/w will do it's own selection then).
Use an INT_PENDING macro to check for an interrupt. The call to
ISP_DMAFREE now just takes the handle- not the 'handle-1' which was
a layering violation. Use CFGPRINTF in a couple of places to make
things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
where it defaults to one. Change simq width allocation to the max number
of commands supported by the HBA after f/w fires up- not the constant
MAXISPREQUEST value. Do some stylistic changes.
Add in null SWIZZLE definitions. Add in CFGPRINTF define. Change default
debug level to refer to an external isp_debug variable. Remove inline
functions as they're now in isp_inline.h and include that file.
the result queue length is never less than 64. Move (ick) temp port
database used for post-LIP merging off the kernel stack and put it
into the softc. Remove some target mode stuff which will come back
later in a different file. Change how the list of outstanding commands
are stored (now allocated at mailbox setup time to be just enough for
the max for a specific HBA which can vary). Keep a rotating seed of
the last index for this in the softc. Increase the count of active
commands from 10 to 16 bits.
- Generally clean things up.
- PnP now supported.
Will convert to bus_space, ifmedia and add a DEVICE_IDENTIFY() method
for autodetection. As it stands
device ex0 at isa0
should find a card if one is present.
I feel less dirty now.
In order to make this work, I created a pseudo-PHY driver to deal with
Macronix chips that use the built-in NWAY support and symbol mode port.
This is actually all of them, with the exception of the original MX98713
which presents its NWAY support via the MII serial interface.
The mxphy driver actually manipulates the controller registers directly
rather than using the miibus_readreg()/miibus_writereg() bus interface
since there are no MII registers to read. The mx driver itself pretends
that the NWAY interface is a PHY locayed at MII address 31 for the sole
purpose of allowing the mxphy_probe() routine to know when it needs to
attach to a host controller.
32 bytes is safe.
Handle successful completion of message log retrieval commands.
With these changes, the driver correctly handles the consequences of drive
death and replacement in a reliable array. Note that the massive backlog
of I/O during handling of such an event can kill the system if softupdates
is enabled.
Without it the kernel config options, like OVERRIDE_TUNER, where not
getting passed to the driver.
Bug noticed by: Marc Fonvieille <fonvi@club-internet.fr>
now lives in the respective bus front end files.
- Add various function prototypes to if_edvar.h
- Clean up some debugging code that snuck into if_ed_isa.c
- Turn on the right bits in files.i386
* Change the hack used on the alpha for mapping devices into DENSE or
BWX memory spaces to a simpler one. Its still a hack and should be
a seperate api to explicitly map the resource.
* Add $FreeBSD$ as necessary.
PJ cards. This will probably also support the AcceleRAID and
eXtremeRAID cards, but nobody has volunteered one for testing, so I
haven't enabled their PCI device IDs.
Slightly clean up communication between the disk devices and the
controller device as per new practice, and move some more register-
related items int mlxreg.h from mlxvar.h.
Remove some unnecessary read-modify-write operations to the card
control registers; they don't behave like that.
Increase the status polling interval to 10 seconds. It's still possible
to load the card up to the point where a status poll will find the
previous poll still running, but this will reduce the incidence of
complaints.
maximum of 64 kB.
vinum_conf, struct drive: add fields for the current number of active
requests and the maximum ever active.
struct sd: Add fields for initialize progress.
struct mc: set the size of saved file names to MCFILENAMELEN instead
of the previous explicit constant.
limit the number of outstanding requests on a specific drive and
overall.
Change the way we set the active request count. This enables us to
start the requests without being in splbio for the duration, which
could be very long for IDE drives in PIO mode.
context. Be prepared to fail instead.
MMalloc, FFree: ensure that saved file names are properly terminated.
Use MCFILENAMELEN instead of the previous explicit constant.
and then doing it itself, resulting in a panic downed drives.
Sleuth-work-by: Christopher Masto <chris@netmonger.net>
Remove dummy function initsd, which is now (implemented) in
vinumrevive.c
vinum_scandisk: Check that a drive is up before reading from it. This
is probably excessive paranoia.
Rather than teaching pci_ioctl about hoses, we just pass down a magic number
& let the platform code figure out what the hose is based on what the bus
number is.
concept approved by dfr
resource_list_release. This removes the dependancy on the
layout of ivars.
* Move set_resource, get_resource and delete_resource from
isa_if.m to bus_if.m.
* Simplify driver code by providing wrappers to those methods:
bus_set_resource(dev, type, rid, start, count);
bus_get_resource(dev, type, rid, startp, countp);
bus_get_resource_start(dev, type, rid);
bus_get_resource_count(dev, type, rid);
bus_delete_resource(dev, type, rid);
* Delete isa_get_rsrc and use bus_get_resource_start instead.
* Fix a stupid typo in isa_alloc_resource reported by Takahashi
Yoshihiro <nyan@FreeBSD.org>.
* Print a diagnostic message if we can't assign resources to a PnP
device.
* Change device_print_prettyname() so that it doesn't print
"(no driver assigned)-1" for anonymous devices.
their HotRod controller and on SIIG PCI ultra DMA controller. These
changes also made lots of the Promise code go away, its all much more
generic this way.
Get rid of atapi_immed_cmd, instead use the queue to move atapi commands
from interrupt context if nessesary, the entire atapi layer has
gotten an overhaul.
Lots of fixes to utililize the new features in subr_disk.c etc, and
get rid of the last biots of softc arrays in the drivers, the
only one left is atadevices which cannot easily go away (yet).
Use our own malloc names, its a lot easier to track memory usage this way.
General cleanup overall.
- Work around a problem not yet solved in the tree (but solved in mine.)
device_get_ivars() should never be cast to a struct resource_list *
The solution, under review, involves the creation of a
device_get_resource_list() function. More later.
configuration information from a DPT card at a given port.
This is needed by the ISA bus front end (still to come) and the EISA
bus front end (which hasn't ever worked).
- Blow away dpt_eisa.h as the information it contains does not justify
an additional file.
- Convert dpt_eisa.c to use the onboard config instead of trying to
read the EISA configuration registers.
- Some cleanup and improvements in the uhci and ohci drivers
- Support for plugging and unplugging devices improved
- Now available is bulk transport over OHCI controllers
- Resume and suspend have been temporarily been disabled again. Proper
support for it is available in the uhci.c and ohci.c files but I have
not yet spent the brain cycles to use it.
- OpenBSD now uses the USB stack as well
- Add FreeBSD tags
Remove the use of ukbd_disconnect and replace it with direct
calls to disable.
Change printf to DPRINTF
Remove the use of usbd_lock, change it to splusb()/splx()
the AMI PCI controllers using the 8LD firmware interface (40LD firmware
will be supported as soon as I have hardware to test with).
These controllers are rebadged by Dell as the PERC, as well as by HP
and possibly other vendors.
The old algorithm was:
if class == storage and subclass != SCSI device must be IDE
This results in claiming 'raid' and 'other' storage devices as IDE,
which is typically not the case.
Reviewed by: sos
- Move intrhook stuff into kernel.h
- Remove all occurrences of #device <device.h>
- Add kernel.h were necessary (nowhere)
- delete device.h
This file contained the structures for cfdata (old style config) and is no
longer used. It was included by most drivers.
It confuses the remote debugger as the definition of 'struct device' in
device.h is found before the one in bus_private.h.
0x8024b04e) so that the cards description is used instead of overriding
it. While I'm here, add an ID for the SUP2080 and the SUP2030.
PR: kern/13983
Submitted by: Kurt D. Zeilenga <Kurt@OpenLDAP.Org> (SUP2030)
dfr (rest of change)
Reviewed by: dfr
Vendor ID SUP2480 (0x8024b04e), Serial Number 0x00001334
PnP Version 1.0, Vendor Version 0
Device Description: SupraExpress 56i Sp V.90
Reviewed by: dfr
kernel, but gcc provides a pessimal builtin for it.
Makefile.i386:
Added a variable (CONF_CFLAGS) for configuration-specific compiler flags.
LINT:
Use CONF_CFLAGS to inhibit use of gcc builtins.
Add debuging for all failure cases in aha_cmd().
Always check DATAIN_REG_READY even if we're ready to exit the
read loop.
The last fix allows the AHA-1640 MCA SCSI adapter to operate
correctly and likely fixes problems on a few other oddball
adapters. (I suspect my Dell Drive Array in 1540 mode needs this.)
Reviewed by: Warner Losh
apm_saver uses the apm_display() routine from the apm system to
"suspend" the "display" part of the machine.
This is beneficial for some laptops (or other machines with
non-traditional displays) that choke on the 'green' saver's
effect.
Another way of looking at this is that it's the same as a screen
saver that does an 'apm -d 0' to blank the display and an 'apm -d 1'
to bring it back. One probably ought to use these commands to make
sure the effect will be correct before using it unattended.
For unknown devices the output will now be
pci0: unknown card (vendor=0x109e, dev=0x0878) at 14.1 irq 19
instead of
pci0: unknown card DD^0878 (vendor=0x109e, dev=0x0878) at 14.1 irq 19
Before this change, the code used to take the PCI vendor id and translate it
into a three letter ASCII name.
For PnP devices, the vendor id _does_ map to a nice ASCII name
(eg Creative Labs PnP ID maps to "CTL", ESS PnP ID maps to "ESS")
But there is no such mapping for PCI devices, as can be seen by the
example above where the Brooktree PCI vendor ID maps to "DD^"
The PCI Special Interest Group confirmed they do not have any mappings
from vendor ID to ASCII.
and/or when using the card.
o Convert the driver to using bus_space. This allows alphas with
fxp's to boot, rather than panic'ing because rman_get_virtual()
doesn't really return a virtual address on alphas.
o Fix an alpha unaligned access error caused by some misfeature of
gcc/egcs: if link_addr & rbd_addr in the fxp_rfa struct are 32 bit
quantities, egcs will assume they are naturally aligned. So it will do
a ldl & some shifty/masky to twiddle 16 bit values in fxp_lwcopy().
However, if they are 16-bit aligned, the ldl will actually be done on
a 16-bit aligned value & we will panic with an unaligned access
error... Changing their definition to an array of chars seems to fix
this. I obtained this from NetBSD.
I've tested this on both i386 & alpha.
of parity check and rebuild operations. This enables us
to stop the operation and restart at a later time.
enum parityop: Trivial enum to decide what parityops() is going to do.
could stand.
Define the correct return lengths for a number of ioctls.
Add ioctls VINUM_CHECKPARITY and VINUM_RESETPARITY, still to be fully
implemented.
ourselves. This breaks a vicious circle which caused
vinum to dereference a null vp if device nodes were
missing.
Reported-by: Brad Chisholm <sasblc@unx.sas.com>
Alec Wolman <wolman@cs.washington.edu>
check_drive: Don't take a drive down if it's only referenced.
read_drive: Remove unused variable.
get_empty_volume: initialize plexes to -1 (not allocated)
remove_drive_entry:
Remove recurse parameter (there's nothing below a drive in the hierarchy).
Use remove_sd_entry to remove sds, don't do it ourselves.
Log errors, don't throw rude remarks.
remove_plex_entry:
Don't use plex->subdisks as a loop limit, it gets changed in the
loop. This caused some removals to only remove half the subdisks.
Change logging of some "impossible" situations.
remove_volume_entry:
Use remove_plex_entry to remove plexes, don't do it ourselves.
update_sd_config:
Use set_sd_state to do the work.
will have to mknod yourself for now.
* don't eat the first write()
* partial rvplayer fix- don't panic on unaligned writes unless our
feeder chain requires them for downconversion. a fuller fix is
on the way.
I386_BUS_SPACE_IO. Compiles now on the Alpha, but likely will not
work due to bus space address <-> virtual address mapping bogons that
work for i386 but not alpha.
work. Be more verbose when one cannot allocate IRQ, et al since this
is a common configuration problem. The cards have the IRQ soft wired
into their BIOS and do not try to do collision detection. This can
cause problems when this IRQ is the same as another card/device.
The PNP hasn't been tested. My PNP board is in a deployed system.
I'll sneak in testing of it sometime later. I've been able to mount
the 3.3R cdrom that arrived today and access files off it.
Submitted by: dfr
Leadtek Winfast 2000 cards.
No audio support yet, just the card make is reported.
Submitted by: Craig <crh@outpost.co.nz>
Submitted by: Peter Wemm <peter@netplex.com.au>
BUF_LOCKFREE a buffer prior to physically freeing it. While these
bugs did not cause a crash, they might in the future.
Added eof handling for unlabeled partitions.
Submitted by: Tor.Egge@fast.no
- Split out the prototypes, externs and struct decls from if_epreg.h into
if_epvar.h.
- Add support for MCA based Etherlink III (3c529) devices.
None of this code is used right now; the old if_ep driver is still
in place and used.
I will eventually get around to converting if_ep_isa.c to newbus once I've
had a talk with Peter and DFR about the DEVICE_IDENTIFY() method.
I have tested this code on my PS/2. It works. I would like EISA and ISA
testers since my example hardware hasn't arrived yet.
Add:
dev/ep/if_ep.c optional ep
dev/ep/if_ep_isa.c optional ep isa
dev/ep/if_ep_eisa.c optional ep eisa
dev/ep/if_ep_mca.c optional ep mca
dev/ep/if_ep_pccard.c optional ep card
to sys/conf/files
Remove:
i386/eisa/3c5x9.c optional ep
i386/isa/if_ep.c optional ep
from sys/i386/conf/files.i386
PCCARD testers wanted!
I will switch off and cvs rm the old driver in favor of this copy once
I've had positive feedback or have the hardware to verify that it works.
have been there in the first place. A GENERIC kernel shrinks almost 1k.
Add a slightly different safetybelt under nostop for tty drivers.
Add some missing FreeBSD tags
fields in struct cdevsw:
d_stop moved to struct tty.
d_reset already unused.
d_devtotty linkage now provided by dev_t->si_tty.
These fields will be removed from struct cdevsw together with
d_params and d_maxio Real Soon Now.
The changes in this patch consist of:
initialize dev->si_tty in *_open()
initialize tty->t_stop
remove devtotty functions
rename ttpoll to ttypoll
a few adjustments to these changes in the generic code
a bump of __FreeBSD_version
add a couple of FreeBSD tags
This means that we will not have to have a bpf and a non-bpf version
of our driver modules.
This does not open any security hole, because the bpf core isn't loadable
The drivers left unchanged are the "cross platform" drivers where the respective
maintainers are urged to DTRT, whatever that may be.
Add a couple of missing FreeBSD tags.
for you to be told there was an error [during verbose boot].
I poked him for the fix, he poked me to get it committed.
Submitted by: Jason Young <doogie@anet-stl.com>
Enhance MIRROR code. Add a few more sanity checks and implement
a zone-based disk selector to make use of both disks when reading.
Also implement a read fail-over. If a read error occurs on one
disk, the I/O is retried on the other.
NOTE: CCD's mirroring support cannot deal with write errors properly
in regards to recovery, meaning that 'old' data under a write error may
be read non-deterministically if you reboot after a write error, and CCD
certainly cannot deal with a disk changeout. And it still can't. Use
vinum if you are really serious about mirroring. CCD basically just
implements a poor-man's mirror.
sum the total amount of I/O issued to determine when all the I/O
has completed. This fails when the EOF boundry occurs in the middle
of an I/O. Using cbp->cb_buf.b_bufsize works better.
there are stubs compiled into the kernel if BPF support is not enabled,
there aren't any problems with unresolved symbols. The modules in /modules
are compiled with BPF support enabled anyway, so the most this will do is
bloat GENERIC a little.
The lun is not incremented in the ata-disk driver when ATA_STATIC_ID
is not defined, thanks to Kenneth Wayne Culver <culverk@wam.umd.edu>
for finding that one.
PHK pointed at the & problem in atapi-cd in devstat_end_transaction_buf.
Too little sleep I guess...
Phase 1) move the driver
Phase 2)
Phase 3) Profit, by splitting the driver into smaller files like
bktr_tuner, bktr_card, bktr_audio, bktr_<osname>
making it easier to maintain and understand.
declaration for the interface driver from "foo" to "if_foo" but leave the
declaration for the miibus attached to the interface driver alone. This
lets the internal module name be "if_foo" while still allowing the miibus
instances to attach to "foo."
This should allow ifconfig to autoload driver modules again without
breaking the miibus attach.
It been awhile since the last major update, as a benefit there
are some cool things in this one (and new bugs probably :) )...
The ATA driver has grown "real" timeout support for all devices.
This means that it should be possible to get in contact with
(especially) lost ATAPI devices. It also means that the ATA
driver is now usable on notebooks as it will DTRT on resume.
An experimental hack at utilizing the Promise66's at UDMA66 is
in there, but I cant test it. If someone feels like sending
me one, give me a ping.
The ATAPI DMA enableling scheme has been changed, also better DMA
support for the Aladdin chipset has been implemented for ATAPI
devices. Note that the Aladdin apparently only can do DMA reads
on ATAPI devices, and the Promise cant do ATAPI DMA at all.
I have seen problems on some ATAPI devices that should be able
to run in DMA mode, so if you encounter problems with hanging
atapi devices during the probe, or during access, disable DMA
in atapi-all.c, and let me know. It might be nessesary to do this
via a "white list" for known good devices...
The ATAPI CDROM driver can now use eject/close without hanging and
the bug that caused reading beyond the end of a CD has been fixed.
Media change is also handled proberly. DVD drives are identified
and are usable as CDROM devices at least, I dont have the HW to
test this further, see above :).
The ATAPI tape driver has gotten some support for using the DSC
method for not blocking the IDE channel during read/write when
the device has full buffers. It knows about the OnStream DI-30
device, support is not completed yet, but it can function as a
primitive backup medium, without filemarks, and without bad media
handeling. This is because the OnStream device doesn't handle this
(like everybody else) in HW. It also now supports getting/setting
the record position on devices that supports it.
Some rather major cleanups and rearrangements as well (cvs -b diff
is your freind). I'm closing in on declaring this for beta code,
most of the infrastruture is in place by now.
As usual USE AT YOUR OWN RISK!!, this is still alpha level code.
This driver can hose your disk real bad if anything goes wrong, but
now you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
This whole idea isn't going to work until somebody makes the bus/kld
code smarter. The idea here is to change the module's internal name
from "foo" to "if_foo" so that ifconfig can tell a network driver from
a non-network one. However doing this doesn't work correctly no matter
how you slice it. For everything to work, you have to change the name
in both the driver_t struct and the DRIVER_MODULE() declaration. The
problems are:
- If you change the name in both places, then the kernel thinks that
the device's name is now "if_foo", so you get things like:
if_foo0: <FOO ethernet> irq foo at device foo on pcifoo
if_foo0: Ethernet address: foo:foo:foo:foo:foo:foo
This is bogus. Now the device name doesn't agree with the logical
interface name. There's no reason for this, and it violates the
principle of least astonishment.
- If you leave the name in the driver_t struct as "foo" and only
change the names in the DRIVER_MODULE() declaration to "if_foo" then
attaching drivers to child devices doesn't work because the names don't
agree. This breaks miibus: drivers that need to have miibuses and PHY
drivers attached never get them.
In other words: damned if you do, damned if you don't.
This needs to be thought through some more. Since the drivers that
use miibus are broken, I have to change these all back in order to
make them work again. Yes this will stop ifconfig from being able
to demand load driver modules. On the whole, I'd rather have that
than having the drivers not work at all.
usually cleared by a successful selection, but there is no guarantee
that a future successful selection will ever occur (e.g. empty bus).
The driver never looks at SELINGO, but the busy LED does, so this
change has the cosmetic effect of fixing the rare instance where the
busy LED was left on, confusing the user.
aic7xxx parts. This problem could result in data corruption
during periods of my PCI bus load by busmasters other than the
aic7xxx.
Many thanks to Andrew Gallatin <gallatin@cs.duke.edu> for characterizing
the symptoms of this problem and testing this fix.
adjust the bp->b_bcount the same way for unlabeled VN access as dscheck
does for labeled access.
We also increase the block size to at least 8K for efficiency.
Reviewed by: Tor.Egge@fast.no
- Remove sc_get_scr_stat(). It's not necessary anymore.
- Call ttymalloc() to allocate the struct tty for each vty, rather than
statically declaring an array of struct tty. We still need a statically
allocated struct tty for the first vty which is used for the kernel
console I/O, though.
- Likewise, call ttymalloc() for /dev/sysmouse and /dev/consolectl.
- Delete unnecessary test on the pointer struct tty *tp in some functions.
- Delete unused code in scmouse.c.
WARNING: this change requires you to recompile screen savers!
1) Reworked the probe routine
2) Addition of the 574B's product ID.
3) Added useful info when booting verbosely.
Submitted by: Jason Young <doogie@anet-stl.com>
Bug fix: xmradio nolonger experiences a 6Mhz offset after running FXTV
New feature: Automatic Tuner selection for AVerMedia cards with
configuration EEPROMs on (ie the Bt878 based cards)
length for mini receive ring. The max length was MHLEN, however the mbufs
are actually shortened to MHLEN - ETHER_ALIGN to force payload alignment.
PR: 13793
size != 512 that are configured without a label. The bug should only
have effected swap-backed VN mounts without a label.
Add several major features to VN. In the kernel we add a swap
pre-reservation capability, which can be used to guarentee seek
consistency for swap-backed VN nodes. This also incidently allows
a swap-backed VN filesystem to be recovered after a crash in some
cases (if the same swap blocks happen to be reserved).
We also add a number of new options to vnconfig which do the work
of pre-zeroing or creating/truncating/extending a file which greatly
simplifies using VN in a file-backed configuration.
Add FreeBSD CVS label to sys/sys/vnioctl.h, as well as a new ioctl
flag for the swap pre-reservation feature.
Reviewed by: Alan Cox <alc@cs.rice.edu>, David Greenman <dg@root.com>
warnings caused by the arg having the wrong type (not const enough).
The arg was also wrong (a full name instead of a short one) for calls
from from subr_diskmbr.c and pc98/diskslice_machdep.c.
rewrite the pccard attachment case. This is a work in progress, but
doesn't break the isa case.
I left the #if 0...#endif around the pccard stuff, at Peter's request,
so that normal users don't shoot themselves in the foot.
While I was here:
o Indent a comment to the right location
o Spell Unknown with a final 'n'.
Reviewed by: peter
I have an 82559 card with the same id as the other 8255[78] chips, but
that was made with a date code of 0699 (June 99). The submitter shows
this working with the probe etc, but doesn't actually say it works as
on the ethernet. :-) Assuming it does, this is a RELENG_3 merge candidate.
Submitted by: Steven E Lumos <slumos@sam.ISRI.UNLV.EDU>
this PHY and the Davicom DM9101 have exactly the same register definitions.
One of them is probably a clone of the other. I'm not sure which.
This is needed for the Davicom DM9102 10/100 PCI ethernet driver which
will be committed shortly.
Doug Rabson's work, with a few tweaks from Warner Losh and I. There are
still some quirks to resolve, but the old driver is presently breaking
the build.
a quick think and discussion among various people some form of some of
these changes will probably be recommitted.
The reversion requested was requested by dg while discussions proceed.
PHK has indicated that he can live with this, and it has been agreed
that some form of some of these changes may return shortly after further
discussion.
MCA SCSI adapters.
bt_mca.c is going to live in sys/dev/buslogic instead of sys/dev/mca
as per a conversation with Peter, Doug and Mike.
Thanks to Andy Farkas <andyf@speednet.com.au> for being such a good
sport and doing all the testing for me (as I don't actually own one
of these cards. Yet.)
`ED_P1_MAR + i' and `ED_P1_PAR + i', respectively.
- convert ED_PC_RESET and ED_PC_MISC into relative offset from
ED_PC_ASIC_OFFSET (those macros are not used in current source).
Submitted by: chi@bd.mbn.or.jp (Chiharu Shibata)
