and released. It should use `spcl' consistently in both cases,
otherwise shift/control/alt state may not be correctly set/reset.
(Even with this fix, you can still make syscons confused and fail to
change internal state if you really want to, by installing a really
arcane and artificial keymap.)
PR: i386/4030
Reviewed by: sos
instructions more (many cases were already intended to be byte-sized
but were missing prefixes so gas assembled them bogusly), and
rearranging a loop to test at the end.
this code is controlled by smptests.h: TEST_CPUSTOP, OFF by default
new code for handling mixed-mode 8259/APIC programming without 'ExtInt'
this code is controlled by smptests.h: TEST_ALTTIMER, ON by default
- TEST_CPUSTOP adds stop_cpus()/restart_cpus(), OFF by default
- TEST_ALTTIMER new method for attaching 8259 PIC to APIC
this method avoids 'ExtInt' programming, ON by default
- TIMER_ALL sends 8259/8254 timer INTs to all CPUs, ON by default
- ASMPOSTCODExxx code to display bytes to POST hardware, OFF by default
and bios.S were small enough and have been merged back into their
respective files in biosboot/, conditionalized on CDBOOT. Other
files might be merged at a later stage.
Caveat emptor: i cannot test this right now.
This is the long-threatened ISO 9660 CD-ROM bootstrap code.
This work has been sponsored by Plutotech International, Inc (who paid
the initial work), and interface business GmbH (where i did most of
the work). A big thanks also goes to Bruce Evans, for his continuing
help and answering my stupid questions.
The code is basically functioning, with the following caveats:
. Rock Ridge attributes are not yet supported.
. Only SCSI CD-ROMs are supported, since i fail to see any possibility
to determine the drive type using BIOS functions. (Even for hard disks,
this determination is done by a big hack only.)
. El Torito specifies a lot of crap and useless misfeatures, but crucial
things like the ability to figure out the CD TOC have been ``forgotten''.
Thus, if you wanna boot a multisession CD, you need to know at which CD
block your session starts, and need to speciffy it using the @ clause.
. None of the CD-ROM controllers i've seen so far implements the full
El Torito specification at all. Adaptec is probably the closest, but
they miss on non-emulation booting (which would be the most logical
choice for us). Thus, the current code bloats the 7.5 KB boot code
up to 1.44 MB, in order to fake a `floppy' image.
If you wanna use it, specify this file as the boot image on the
command-line of the mksiosfs command (option -b).
Caveat emptor: some versions of the Adaptec BIOS might even fail to
access the CD-ROM at all, using the BIOS functions. I think i've
notice this for ver 1.26, the code has been tested with ver 1.23.
The boot string is as follows:
[@sess-start] [filename] [-flags]
sess-start Extend # where the last session starts, measured in
CD-ROM blocks.
filename As usual, but the input is case-insensitive by now
(since we don't grok RR anyway).
flags As usual, but -C (use CDROM root f/s) is default, so
specifying -C will decactivate this option (which is
probably not what you want :).
A lot of cleanup work is probably required, and some of the files
could/should be merged back to biosboot, perhaps made conditional on
some #ifdef. The malloc implementation that comes with cdboot might
also be useful for kzipboot. (I needed a malloc() since the root dir
ain't fixed in size on a CD.)
I've been testing all this with a 2.2-STABLE as the base for biosboot.
I don't expect too many surprises, although i know the biosboot stuff
has been changed a lot in -current lately. I'm sure Bruce will
comment on all this here anyway. :-)
This work has been sponsored by Plutotech International, Inc (who paid
the initial work), and interface business GmbH (where i did most of
the work). A big thanks also goes to Bruce Evans, for his continuing
help and answering my stupid questions.
The code is basically functioning, with the following caveats:
. Rock Ridge attributes are not yet supported.
. Only SCSI CD-ROMs are supported, since i fail to see any possibility
to determine the drive type using BIOS functions. (Even for hard disks,
this determination is done by a big hack only.)
. El Torito specifies a lot of crap and useless misfeatures, but crucial
things like the ability to figure out the CD TOC have been ``forgotten''.
Thus, if you wanna boot a multisession CD, you need to know at which CD
block your session starts, and need to speciffy it using the @ clause.
. None of the CD-ROM controllers i've seen so far implements the full
El Torito specification at all. Adaptec is probably the closest, but
they miss on non-emulation booting (which would be the most logical
choice for us). Thus, the current code bloats the 7.5 KB boot code
up to 1.44 MB, in order to fake a `floppy' image.
If you wanna use it, specify this file as the boot image on the
command-line of the mksiosfs command (option -b).
Caveat emptor: some versions of the Adaptec BIOS might even fail to
access the CD-ROM at all, using the BIOS functions. I think i've
notice this for ver 1.26, the code has been tested with ver 1.23.
The boot string is as follows:
[@sess-start] [filename] [-flags]
sess-start Extend # where the last session starts, measured in
CD-ROM blocks.
filename As usual, but the input is case-insensitive by now
(since we don't grok RR anyway).
flags As usual, but -C (use CDROM root f/s) is default, so
specifying -C will decactivate this option (which is
probably not what you want :).
A lot of cleanup work is probably required, and some of the files
could/should be merged back to biosboot, perhaps made conditional on
some #ifdef. The malloc implementation that comes with cdboot might
also be useful for kzipboot. (I needed a malloc() since the root dir
ain't fixed in size on a CD.)
I've been testing all this with a 2.2-STABLE as the base for biosboot.
I don't expect too many surprises, although i know the biosboot stuff
has been changed a lot in -current lately. I'm sure Bruce will
comment on all this here anyway. :-)
because there was no non-inline spl0() to call.
Don't frob intr_nesting_level in idle() or cpu_switch(). Interrupts
are mostly disabled then, so the frobbing had little effect.
is defined, or SMP is defined. It is silly to configure PERFMON when
it can't work (it will be disabled at runtime), but I like to leave
the PERFMON configuration alone when I temporarily disable support for
modern CPUs to run regression tests.
Removed an unused #include.
- Added the psm options PSM_HOOKAPM and PSM_RESETAFTERSUSPEND.
LINT:
- Added the psm options PSM_HOOKAPM and PSM_RESETAFTERSUSPEND.
- Added comments on the flag 0x20 for syscons.
- Clarified descriptions on the flags (0x02, 0x04) regarding the cursor
shape in syscons.
cursor (CHAR_CURSOR)
1. Reduced the number of calls to set_destructive_cursor(). The
destructive cursor produced noticeable overhead on the system. It was
caused by draw_cursor_image() calling set_destructive_cursor() every
so often.
set_destructive_cursor() absolutely needs to be called when
a) the character code under the cursor has changed either because
the cursor moved or because the screen was updated or the mouse
pointer overlapped the cursor.
b) Or a new font has been loaded,
c) or the video mode has been changed,
d) or the cursor shape has been changed,
e) or the user switched virtual consoles.
2. Turn off the configuration flag CHAR_CURSOR (destructive cursor) in
scattach() if we have a non-VGA card. The destructive cursor works
only for VGA.
3. Removed redundant calls to set_destructive_cursor() in some places.
4. Fixed the "disappearing mouse pointer" problem. The mouse pointer
looked hidden under the destructive cursor when it overlaped the cursor.
A slightly different version of the patch was reviewd and OKed by
sos and ache.
If the configuration option PSM_HOOKAPM is defined and the APM device
is available, the psm driver will issue the ENABLE command to the
pointing device at the resume APM event if the device was open when
the system went into suspended mode. If the option
PSM_RESETAFTERSUSPEND is specified in addition to PSM_HOOKAPM, the
driver will try to reset the pointing device before sending the
ENABLE command.
Built-in PS/2-type pointing devices in some laptops (all the reports I
heard were about Toshiba models) sometimes don't work immediately
after the system is resumed. The device MAY become available after a
while. The system may exhibit the same symptom in other OS's too
(no, FreeBSD is not the only OS that is suffering :-).
I don't know the correct way of solving this yet, but it's been
reported that issuing the ENABLE command after resumption wakes up the
pointing device.
Without PSM_HOOKAPM, the psm driver behaves in the same way as before.
Problem reported in the bsd-nomads mailing list in Japan.
fix stopped it being used in all cases, because substitution on unset
variables does not work.
When profiling, put -malign-functions=4 in CFLAGS instead of in PROF.
This fixes the histogram counts for profiling support functions. It
gives bogus but harmless extra alignment for genassym etc.
Add a new configuration flag, KBD_NORESET (0x20) to tell scprobe() not
to reset the keyboard.
IBM ThinkPad 535 has the `Fn' key with which the user can perform
certain functions in conjunction with other keys. For example, `Fn' +
PageUP/PageDOWN adjust speaker volume, `Fn' + Home/End change
brightness of LCD screen. It can also be used to suspend the system.
It appears that these functions are implemented at the keyboard level
or the keyboard controller level and totally independent from BIOS or
OS. But, if the keyboard is reset (as is done in scprobe()), they
become unavailable. (There are other laptops which have similar
functions associated with the `Fn' key. But, they aren't affected by
keyboard reset.)
ThinkPad 535 doesn't have switches or buttons to adjust brightness and
volume, or to put the system into the suspend mode. Therefore, it is
essential to preserve these `Fn' key functions in FreeBSD. The new
flag make scprobe() skip keyboard reset.
If this flag is not set, scprobe() behaves in the same say as before.
(If we only knew a way to detect ThinkPad 535, we could skip keyboard
reset automatically, but...)
- added Xcpustop IPI code to support stop_cpus()/restart_cpus().
it is off by default, enable via smptests.h:TEST_CPUSTOP
intr_machdep.h:
- moved +ICULEN to lower level.
- added entry for Xcpustop.
General cleanup.
New functions to stop/start CPUs via IPIs:
- int stop_cpus( u_int map );
- int restart_cpus( u_int map );
Turned off by default, enabled via smptests.h:TEST_CPUSTOP.
Current version has a BUG, perhaps a deadlock?
This variable is a bitmap showing all CPUs present EXCEPT the CPU
owning the variable. In other words, it is equal to the global bitmap
'all_cpus' minus its own bit.
Till now NMIs would be ignored. Now an NMI is caught by the BSP.
APs still ignore NMI, am working on code to allow a CPU to stop other CPUs
via an IPI.
available to the kernel (VM_KMEM_SIZE). The default (32 MB) is too low
when having 512 MB or more physical memory in a server environment. This is
relevant on systems where "panic: kmem_malloc: kmem_map too small" is a
problem.
value (200) is too low in some environments, causing a fatal
"panic: get_pv_entry: cannot get a pv_entry_t". The same panic might
still occur due to temporary shortage of free physical memory
(cf. PR i386/2431).
were returning EFAULT, when it is a completely acceptable thing to do.
Also, at the same time, be a *bit* optimizing and don't allocate any
"stackgrap" memory if we're not going to use it.
This is another Oracle-discovered problem.
Submitted by: Steven Wallace
the XENIX version is packed, and two bytes smaller than ours. So, define
the structure, and have it packed. I used the __attribte__((packed))
modifier for this; I could also have surrounded the struct definition with
#pragma pack(2) -- but that would have meant making ibcs2_timeb's definition
outside the function. This may need to be revisited if we ever want to
compile with a compiler other than gcc. (I also used 'unsigned long'
instead of 'time_t' because I am writing to match an external specification
-- and the definition of time_t could change.)
Reviewed by: Steven Wallace
This eliminates a lot of #ifdef SMP type code. Things like _curproc reside
in a data page that is unique on each cpu, eliminating the expensive macros
like: #define curproc (SMPcurproc[cpunumber()])
There are some unresolved bootstrap and address space sharing issues at
present, but Steve is waiting on this for other work. There is still some
strictly temporary code present that isn't exactly pretty.
This is part of a larger change that has run into some bumps, this part is
standalone so it should be safe. The temporary code goes away when the
full idle cpu support is finished.
Reviewed by: fsmp, dyson
The kernel with USERCONFIG_BOOT and VISUAL_USERCONFIG option presents
the user the kernel configuration menu upon boot.
The user can navigate the menu with cursor keys. I think it would be
nice if the user can navigate and select a menu item with regular keys
as well, so that the user who is using a serial console which is not
so capable of esc sequences still can choose a menu item.
With the following patch we can select an item by typing an item
number, 1, 2, or 3, or mnemonic `s' to skip UserConfig, 'v' to enter
the visual mode, and `c' to start the CLI mode. `p', `u', `n', and `d'
will move cursor up and down.
Submitted by: yokota
adapter during the system boot. It always assumes there is at least a
monochrome adapter.
This is rather strange assumption. If there is no dispaly adapter, the
console driver cannot be any good...
In this patch, scinit() is split into two parts; the first part is
now called scvidprobe() which will detect the presence of video card
at the CGA or MONO buffer address and returns TRUE if found. It is
called during sccnprobe() and scprobe(). Both will fail if no video
card is found.
The second part, whose name stays the same as before, scinit(), is
called from sccninit() and scattach() to complete initialization of
the found video card.
The keyboard probe code is moved from scprobe() to sckbdprobe();
scprobe() now calls scvidprobe() and sckbdprobe() to carry out device
probe. (This is rather a cosmetic change, but it sure makes the code
look better organized.)
The problem pointed out by Joerg.
since it is impossible to distinguish unpromoted types from small
(struct) types. Renamed __va_promote() to __va_size() since it is
related to sizes of args on the stack and not to promotion.
PR: 3884
Submitted by: mostly by arnej@math.ntnu.no (Arne Henrik Juul)
Obtained from: name of__va_size and some parentheses fixes from NetBSD
by checking whether APM is active in apm_power_off() and returning
if not. (The code was already written with the expectation that
this function would return if it fails.)
NETNATM --> NATM
reported by Bruce Evans.
Bruce also pointed out that NATM is confusing since config(8) defines
NATM as the number of atm pseudo device in "BUILD_DIR/atm.h".
We might change the name in the future but leave it as it is for now.
will see it. The name of the file is obtained by appending ".config"
to the name of the kernel file. If the file doesn't exist, then an
annoying message is printed.
Reduced the command line buffer size yet again from 4096 to 1024. It is
oversized to defend against overrun in gets(), but data space is starting
to run out so the buffer size can't be as grossly oversized as before.
- Added support for "dual" internal/serial consoles (-D flag). If -D is set,
then all i/o from the boot blocks is to and from both the internal console
and the serial console. -D has no effect on the kernel (-h decides the
kernel serial console as usual). -D should normally be set in /boot.config.
- Get help messages from /boot.help. You should copy boot.help from the
biosboot directory to the root directory on the boot drive when you
install new boot blocks.
- New, less invasive keyboard probe. Enable keyboard probe dynamically (-P
flag). Should probably never be used (use -h instead).
- Fixed/improved initialization from boot.config. It didn't interact correctly
with the NAMEBLOCK option, and the initialization of the drive/unit/partition
didn't stick when a non-default kernel name was entered.
- Don't reset or forget the default drive/unit/... or kernel name so often.
- Set the default kernel name to something unbootable after `?'.
- Display the defaults better.
- Removed PROBE_KEYBOARD_LOCK option (use -h instead).,
- Removed BOOT_FORCE_COMCONSOLE option (use device flag 0x20 instead).
- Removed -a (RB_HALT) flag. This flag is only used for reboots.
Submitted by: about 2/3 by yokota
then all i/o from the boot blocks is to and from both the internal console
and the serial console. -D has no effect on the kernel (-h decides the
kernel serial console as usual). -D should normally be set in /boot.config.
- Get help messages from /boot.help. You should copy boot.help from the
biosboot directory to the root directory on the boot drive when you
install new boot blocks.
- New, less invasive keyboard probe. Enable keyboard probe dynamically (-P
flag). Should probably never be used (use -h instead).
- Fixed/improved initialization from boot.config. It didn't interact correctly
with the NAMEBLOCK option, and the initialization of the drive/unit/partition
didn't stick when a non-default kernel name was entered.
- Don't reset or forget the default drive/unit/... or kernel name so often.
- Set the default kernel name to something unbootable after `?'.
- Display the defaults better.
- Removed PROBE_KEYBOARD_LOCK option (use -h instead).,
- Removed BOOT_FORCE_COMCONSOLE option (use device flag 0x20 instead).
- Removed -a (RB_HALT) flag. This flag is only used for reboots.
Submitted by: about 2/3 by yokota
cost since it is only done in cpu_switch(), not for every exception.
The extra state is kept in the pcb, and handled much like the npx state,
with similar deficiencies (the state is not preserved across signal
handlers, and error handling loses state).
that I snuck in to our GDB last year. This allows you to debug headless
machines by sharing the console port between the debugger and the system
console. It's not 100% reliabile, but it works well. It's optional
and disabled by default.
Submitted by: Juniper Networks
speed using the boot blocks, instead of a hardcoded value stuck in the
kernel. This way, you can have systems using the same kernel but different
console speeds.
Add a sysctl entry for changing the system console speed.
Lock the user tty speed to match the system console speed.
Nuke CONSPEED.
Reviewed by: bde
bit 10 is the old bit for MTRR (presumably this changed, an older P5 I
have has got it, the newer cpus have the new MTRR bit set)
bit 11 is SEP (fast syscalls), bit 23 is MMX
Fill in the other reserved ones with a stub so that we can see them if
they turn up.
Obtained from: Intel AP-485 rev.06
license managers to obtain the host's ethernet address as
a key.
Note that this implementation takes the first hardware address for
the first ethernet interface found, and disregards the interface name
that may be passed in, as linux ethernet devices are all "ethX".
is incompatible with -pg. (We use a different version of mcount for
profiling frame-pointer-less assembler functions, but gcc doesn't know
about this.)
Added a missing dependency.
Cleaned up trailing backslashes.
Added comment about config's limitations/bugs handling dependencies and
backslashe/newlines.
Finished removing support for isdn drivers.
that lkm's can use them for fiddling the masks without being dependent on
which mode the kernel is compiled in (SMP or UP). This is particularly
for ppp_tty.c which has some domain crossing between the net and tty
subsystems. The values are not used in the spl code, they are for
reference only (ie: the compiled code uses immediate values rather than
an indirect 32 bit address and 32 bit data fetch).
top of the hardware interrupt handlers. Apparently this is slightly
faster with the bit scanning instruction that looks these up - this set of
changes reverts the original change.
Reviewed by: bde
rather than inlines. These are compiled with -fomit-frame-pointer and
work out pretty close to the original routines, but it might be a fraction
slower. The reason for doing this is to prevent the SWI_* and HWI_* values
from being compiled into drivers and lkms etc which is one of the things
that prevents the same lkm from being used on both SMP and UP kernels.
This gives us a lot more scope for experimenting with the splxxx
implementaton for SMP parallelism etc.
Reviewed by: bde
CPU code-named `M2'.
- Use the result of cpuid instruction instead of DIR to identify
6x86MX cpu. DIR0 and DIR1 are not documented in the data sheet, and
cpuid instruction is enabled at reset time.
- Add a function, init_6x86MX() to initialize 6x86MX cpu. It supports
CPU_SUSP_HLT and CPU_IORT options. It always sets NC1 (640K - 1M is
not cached.), and enables L1 cache in write-back mode.
- Fix typo in the comment in identblue().
Hopefully I've done the proper magic to merge changes between 1.17 and
1.17.2.1 into the main trunk. Description of those changes follows:
Brought in changes sent to me in late 1995 by Rich Murphey.
I cleaned up a few things and am currently running these under
2.2-970205-GAMMA.
The changes deal with software debouncing apparently necessary on
todays faster hardware, and also some problems with the use of the -Select
line for the TW-523 sync. This driver allows use of +PaperEnd as an
alternative.
Changes to pmap.c for lapic_t lapic && ioapic_t ioapic pointers,
currently equal to apic_base && io_apic_base, will stand alone with the
private page mapping.
apic.h has defines like:
#define lapic__id lapic->id
Once private pages and "known virtual addr" mapping of the APICs is
ready all 'lapic__XXX' will be changed to 'lapic.XXX', and the defines
will be removed.
Changes to smp.h for lapic_t lapic && ioapic_t ioapic pointers,
currently equal to apic_base && io_apic_base, will stand alone with the
private page mapping.
Adjust the data port address by adding the two low order bits of
the register number. The address port takes only a word address
(i.e. ignores the two low order bits written to it).
mode 1. Omission of this bit makes all config register accesses fail in
on recent chip sets ...
(The problem was reported and debug output provided by: Steve Passe)
- vector.s <- stub called by i386/exception.s
- icu_vector.s <- UP
- apic_vector.s <- SMP
Split icu.s into UP and SMP specific files:
- ipl.s <- stub called by i386/exception.s (formerly icu.s)
- icu_ipl.s <- UP
- apic_ipl.s <- SMP
This was done in preparation for massive changes to the SMP INTerrupt
mechanisms. More fine tuning, such as merging ipl.s into exception.s,
may be appropriate.
reality. There will be a new call interface, but for now the file
pci_compat.c (which is to be deleted, after all drivers are converted)
provides an emulation of the old PCI bus driver functions. The only
change that might be visible to drivers is, that the type pcici_t
(which had been meant to be just a handle, whose exact definition
should not be relied on), has been converted into a pcicfgregs* .
The Tekram AMD SCSI driver bogusly relied on the definition of pcici_t
and has been converted to just call the PCI drivers functions to access
configuration space register, instead of inventing its own ...
This code is by no means complete, but assumed to be fully operational,
and brings the official code base more in line with my development code.
A new generic device descriptor data type has to be agreed on. The PCI
code will then use that data type to provide new functionality:
1) userconfig support
2) "wired" PCI devices
3) conflicts checking against ISA/EISA
4) maps will depend on the command register enable bits
5) PCI to Anything bridges can be defined as devices,
and are probed like any "standard" PCI device.
The following features are currently missing, but will be added back,
soon:
1) unknown device probe message
2) suppression of "mirrored" devices caused by ancient, broken chip-sets
This code relies on generic shared interrupt support just commited to
kern_intr.c (plus the modifications of isa.c and isa_device.h).
be (eventually) architecture independent. It provides an emulation
of the ISA interrupt registration function register_intr(), but that
function does no longer manipulated the interrupt controller and
interrupt descriptor table, but calls the architecture dependent
function setup_icu() for that purpose.
After the ISA/EISA bus code has been modified to directly call the new
interrupt registartion functions (intr_create() and intr_connect()),
the emulation of register_intr() should be dropped.
The C level interrupt handler function should take a (void*) argument,
and the function pointer type (inthand2_t) should defined in some other
place than isa_device.h.
This commit is a pre-requisite for the removal of the PCI specific shared
interrupt code.
Reviewed by: dfr,bde
This is now the default, it delays most of the MP startup to the function
machdep.c:cpu_startup(). It should be possible to move the 2 functions
found there (mp_start() & mp_announce()) even further down the path once
we know exactly where that should be...
Help from: Peter Wemm <peter@spinner.dialix.com.au>
- The 1st (preparse_mp_table()) counts the number of cpus, busses, etc. and
records the LOCAL and IO APIC addresses.
- The 2nd pass (parse_mp_table()) does the actual parsing of info and recording
into the incore MP table.
This will allow us to defer the 2nd pass untill malloc() & private pages
are available (but thats for another day!).
panic( "xxxxx\n" );
to:
printf( "xxxxx\n" );
panic( "\n" );
For some as yet undetermined reason the argument to panic() is often NOT
printed, and the system sometimes hangs before reaching the panic printout.
So we hopefully at least print some useful info before the hang, as oppossed to
leaving the user clueless as to what has happened.
Remove "setdefs.h" and arrange to generate it automatically at
ELF kernel build time.
"gensetdefs.c" is a utility which scans a set of ELF object files
and outputs a line ``DEFINE_SET(name, length);'' for each linker
set that it finds. When generating an ELF kernel, this is run just
before the final link to generate "setdefs.h".
Remove the init_sets() function from "setdef0.c", and its call from
"machdep.c". Since "gensetdefs.c" calculates the length of each
set, it is no longer necessary in an ELF kernel to count the set
elements at kernel initialization time. Also remove "set_of_sets"
which was used for this purpose.
Link "setdef0" and "setdef1" into the kernel only if building for
ELF. Since init_sets() is no longer used, there is no need to link
them into an a.out kernel.
all uses of it with the equivalent calls to setbits().
This change incidentally eliminates a problem building ELF kernels
that was caused by SETBITS.
Reviewed by: fsmp, peter
Submitted by: bde
1) Adjust NFRAMES from 16 to 8 per 16k of memory.
2) Acknowledge interrupts to the card early in the interrupt
handler before processing the event that caused the interrupt.
This frees the card to process addtional events instead of
waiting for the driver to finish handling events.
3) Changed the initialization of the transmit buffers to be a
loop so that the number of buffers can be more easily changed.
4) Moved the code to take the adapter out of loop back mode to just
before we enable the receiver.
I also made the driver dynamically size its resource arrays at attach
time so that we can take full advantage of adapters with more than 16k
of memory.
Richard has some other changes he's working on to improve performance,
but this should get ee16 support working reliably again.
Thanks to Wes Santee <wes@bogon.net> for testing these patches.
Submitted by: Richard Straka <straka@user1.inficad.com>
full implementation of the sate machine as described in RFC1661, and
provides support for plugging in various control protocols. I needed
this to provide PPP support for the BISDN project (right now).
Unfortunatley, while the existing API was almost up to the point, i
needed one minor API change in order to decouple the this-layer-
started and this-layer-finished actions from the respective Up and
Down events of the lower layer. This requires two additional lines in
the attach routines of all existing lower layer interface drivers that
are using syncPPP (shortcutting these actions and events). Apart from
this, i believe i didn't change the API of all this, so everything
should plug in without too many hassles. Please report if i broke
something in the existing drivers.
For a list of features (including new ones like dial-on-demand), and
things still to be done, please refer to the man page i'll commit asap.
Encouraged by: Serge Vakulenko <vak@cronyx.ru>
- gcc assumes that %ecx and %edx are clobbered (due to calling
conventions), thus there is no need for saving/restoring those two
registers.
- %es is reset to default value by real_to_prot, thus there is no need
for saving/restorig that register.
Submitted by: tegge
When an ioctl command SW_XXXX is issued, scioctl() checks if the font
appropriate for the specified mode is already loaded. The check was
correctly done for 8 line and 16 line fonts, but not for 14 line font.
The symbols FONT_8, FONT_14 and FONT_16 were defined as numbers but
were sometimes treated as bit flags. They are now defined as bit
flags.
2) screen blinking (two fixes)
Removed a redundant call to timeout() in do_bell().
Don't let blink_screen() write to the video buffer if the screen is in
the graphics (UNKNOWN) mode.
3) screen saver timeout
The ioctl command CONS_BLANKTIME sets the screen saver's timeout. The
value of zero will disable the screen saver. If the screen saver is
currently running it should be stopped.
4) border color and destructive cursor (two fixes)
The border color and the cursor type can be changed via escape
sequences. But only VGA can change the border color and set the
cursor type to destructive (CHAR_CURSOR) in the current syscons.
scan_esc() failed to check this.
Reviewed by: sos
- TFTP is not needed any longer.
Add some other improvements:
- swapsize is now detected if no value was specified.
- resvport is used by default
- merged code for setting/showing mount options for root/swap.
Submitted by: Luigi Rizzo <luigi@labinfo.iet.unipi.it>
- merged SMP option SMP_AUTOSTART from LINT
- enabled SMP_AUTOSTART, since it's the desired working mode and it's
reported to work now.
PR:
Reviewed by:
Submitted by:
Obtained from:
to fill in the nfs_diskless structure, at the cost of some kernel
bloat. The advantage is that this code works on a wider range of
network adapters than netboot. Several new kernel options are
documented in LINT.
Obtained from: parts of the code comes from NetBSD.
was stale.
Fixed initialization of gdt[] for the BDE_DEBUGGER case. APM entries
clobbered debugger entries if the debugger was loaded (APM is incompatible
with BDE_DEBUGGER) and unused entries were garbage if the debugger wasn't
loaded.
