This change allows one to set the busy_detect flag
required by the synopsys UART at the loader prompt.
This is needed by the EPYC 3000 SoC.
This will give users a working console up to the point where getty is required:
hw.uart.console="mm:0xfedc9000,rs:2,bd:1"
Reviewed by: imp
MFC after: 4 weeks
Differential Revision: https://reviews.freebsd.org/D16399
This change adds a new optional console method cn_resume and a kernel
console interface cnresume. Consoles that may need to re-initialize
their hardware after suspend (e.g., because firmware does not care to do
it) will implement cn_resume. Note that it is called in rather early
environment not unlike early boot, so the same restrictions apply.
Platform specific code, for platforms that support hardware suspend,
should call cnresume early after resume, before any console output is
expected.
This change fixes a problem with a system of mine failing to resume when
a serial console is used. I found that the serial port was in a strange
configuration and an attempt to write to it likely resulted in an
infinite loop.
To avoid adding cn_resume method to every console driver, CONSOLE_DRIVER
macro has been extended to support optional methods.
Reviewed by: imp, mav
MFC after: 3 weeks
Differential Revision: https://reviews.freebsd.org/D15552
Move the allwinner early printf support to the snps driver as it
should work with all implementation.
While here add instruction for enabling it on 64bits SoCs.
opt_compat.h is mentioned in nearly 180 files. In-progress network
driver compabibility improvements may add over 100 more so this is
closer to "just about everywhere" than "only some files" per the
guidance in sys/conf/options.
Keep COMPAT_LINUX32 in opt_compat.h as it is confined to a subset of
sys/compat/linux/*.c. A fake _COMPAT_LINUX option ensure opt_compat.h
is created on all architectures.
Move COMPAT_LINUXKPI to opt_dontuse.h as it is only used to control the
set of compiled files.
Reviewed by: kib, cem, jhb, jtl
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D14941
It calls OF_* functions to check if it needs to implement workarounds.
This may not be the case on arm64 where we support both FDT and ACPI.
Fix this by checking if we are booting on FDT before calling these checks.
Reviewed by: ian
Sponsored by: DARPA, AFRL
Sponsored by: Cavium (Hardware)
Differential Revision: https://reviews.freebsd.org/D14515
the Server Base System Architecture to be a subset of the pl011 r1p5. As
we don't use the removed features it is safe to just attach to the existing
driver as is.
Sponsored by: DARPA, AFRL
This reduces noise when kernel is compiled by newer GCC versions,
such as one used by external toolchain ports.
Reviewed by: kib, andrew(sys/arm and sys/arm64), emaste(partial), erj(partial)
Reviewed by: jhb (sys/dev/pci/* sys/kern/vfs_aio.c and sys/kern/kern_synch.c)
Differential Revision: https://reviews.freebsd.org/D10385
ISA PNP card support (replace by hand version in if_ed). Move module
declarations to the end of some files. Fix PCCARD_PNP_INFO to use
nitems(). Remove some stale comments about pc98, turns out the comment
was simply wrong.
Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
This patch adds support for UART in Armada 3700 family.
It exposes both low-level UART interface, as well as
standard driver methods.
Submitted by: Patryk Duda <pdk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Semihalf
Differential Revision: https://reviews.freebsd.org/D12250
The stdout-path chosen property may include the serial connection details,
e.g. the baud rate. When passing the device to OF_finddevice we need to
strip off this information as it will cause the lookup to fail.
Reviewed by: emaste, manu
Differential Revision: https://reviews.freebsd.org/D6846
At least with Tx FIFO enabled it shows me ~10% reduction of verbose boot
time with serial console at 115200 baud.
Reviewed by: marcel
MFC after: 2 weeks
hardware but lack the larger fifos rev 5 hardware should have.
The linux world (where our FDT data comes from) solved this by adding
a new property to pl011 nodes, "arm,primecell-periphid". When this
property is present, its values override the values in the hardware
periphid registers. For pl011 rev 5 hardware with small fifos, they
override the id so that it appears to be rev 4 hardware.
The driver now uses the new property when present. It also continues
to check the device compat string, to handle older fdt data that may
still be in use on existing systems (on RPi systems it is common to
update system software without updating fdt data which is part of the
boot firmware).
Reviewed by: imp
Starting with rev 5 (which is inexplicably indicated by a version number
of '3' in the Peripheral ID register), the pl011 doubled the size of the
rx and tx fifos, to 32 bytes, so read the ID register and set the size
variables in the softc accordingly.
An interesting wrinkle in this otherwise-simple concept is that the
bcm2835 SoC, used in Raspberry Pi systems among others, has the rev 5
pl011 hardware, but somehow also has the older 16-byte fifos. We check
the FDT data to see if the hardware is part of a bcm283x system and use
the smaller size if so.
Thanks to jchandra@ for pointing out that newer hardware has bigger fifos.
have been in the code all along, but were masked by having a fifo depth of
one byte at the hardware level, so everything kinda worked by accident.
The hardware interrupts when the TX fifo is half empty, so set
sc->sc_txfifosz to 8 bytes (half the hardware fifo size) to match. This
eliminates dropped characters on output.
Restructure the read loop to consume all the bytes in the fifo by using
the "rx fifo empty" bit of the flags register rather than the "rx ready"
bit of the interrupt status register. The rx-ready interrupt is cleared
when the number of bytes in the fifo fall below the interrupt trigger
level, leaving the fifo half full every time receive routine was called.
Now it loops until the fifo is completely empty every time (including
when the function is called due to a receive timeout as well as for
fifo-full).
This is required for FDT's standard "reg-io-width" property
(similar to "reg-shift" property) found in many DTS files.
This fixes operation on Altera Arria 10 SOC Development Kit,
where standard ns8250 uart allows 4-byte access only.
Reviewed by: kan, marcel
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D9785
The pl011 UART has a 16 entry Tx FIFO and a 16 entry Rx FIFO that
have not been used so far. Update the driver to enable the FIFOs
and use them in transmit and receive.
Reviewed by: andrew
Differential Revision: https://reviews.freebsd.org/D8819
Do this here as puc(4) disallows single-port instances; at least
one multi-port PCIe UART chip (in this case, the ASIX MCS9922)
present separate PCI configuration space (functions) for each UART.
Tested using lrzsz and a null-modem cable. The ExpressCard/34
variants containing the MCS9922 should also use MSI with this change.
Reviewed by: jhb, imp, rpokala
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D9123
Remove unused fields from uart_pl011_softc. Add an interrupt mask
field to the softc and use it to set the interrupt mask register.
There should be no functional change introduced here except in the
grab and ungrab functions. In these functions, we now disable and
enable all interrupts rather than just the receive interrupt.
Clear the interrupt state before reading the input char from the
input FIFO. In the current code there is a window between the read
to the data register and the write to the the ICR, during which an
input char will not cause an interrupt.
This fixes the issue by which the serial port input on QEMU freezes
when using the emulated pl011 serial port.
uart we need to handle both it and FDT, and as such we need to have an
architecture specific driver.
Obtained from: ABT Systems Ltd
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D7796
Do not assume that all uart drivers use uart_softc structure as is.
Some do a sensible thing and do declare their uart class and driver
properly and arrive into uart_bus_attach with suitably sized softc.
Submitted by: kan
Sponsored by: DARPA, AFRL
Summary:
Some device trees put "fsl,ns16650" first in the compatible list. This causes
the probe code to choke, even though the device is compatible with ns16650, and
has it listed later in the tree.
Reviewed by: nwhitehorn
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D7676
* Add acpi_if.h to the SRC list in the uart module
* Only include new acpi headers when they are needed
Obtained from: ABT Systems Ltd
MFC after: 1 month
Sponsored by: The FreeBSD Foundation
the uart class to use in a similar way as the fdt driver.
Obtained from: ABT Systems Ltd
MFC after: 1 month
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D7248
and ACPI. As such pull out what will be the common parts of the FDT cpu
detection to a new function that can be shared between them.
Reviewed by: manu
Obtained from: ABT Systems Ltd
MFC after: 1 month
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D7262
In some cases, the driver must handle given properties located in
specific OF subnode. Instead of creating duplicate set of function, add
'node' as argument to existing functions, defaulting it to device OF node.
MFC after: 3 weeks
separate driver. Add support for activating clock and hwreset resources
for these devices when the EXT_RESOURCES option is present.
Reviewed by: andrew, mmel, Emmanuel Vadot <manu@bidouilliste.com>
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D5749
the bus space tag and handle for a uart console, use the values returned by
that routine to set the global uart_bus_space_mem, instead of assuming that
there will be a global variable named fdtbus_bs_tag to set it from.
Also, use OF_getencprop() instead calling fdt32_to_cpu() separately.
will allow for code that uses the old fdt_get_range and fdt_regsize
functions to find a range, map it, access, then unmap to replace this, up
to and including the map, with a call to OF_decode_addr.
As this function should only be used in the early boot code the unmap is
mostly do document we no longer need the mapping as it's a no-op, at least
on arm.
Reviewed by: jhibbits
Sponsored by: ABT Systems Ltd
Differential Revision: https://reviews.freebsd.org/D5258
uart_dev_ns8250 now relies on compatible property instead of additional
'busy-detect' cell. All drivers with compatible = "snps,dw-apb-uart" have
busy detection turned on. DTS files of devices affected by the change
were modified and 'busy-detect' property was removed.
Reviewed by: andrew, ian, imp
Obtained from: Semihalf
Sponsored by: Stormshield
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Differential revision: https://reviews.freebsd.org/D4218
This compatibility string is used in .dts file of Armada38x
and isrequired for driver attachment.
Reviewed by: andrew, ian, imp
Obtained from: Semihalf
Sponsored by: Stormshield
Submitted by: Michal Stanek <mst@semihalf.com>
Differential revision: https://reviews.freebsd.org/D4216
to actually wait until the TX FIFOs of UARTs have be drained before
returning. This is done by bringing the equivalent of the TS_BUSY flag
found in the previous implementation back in an ABI-preserving way.
Reported and tested by: Patrick Powell
Most likely, drivers for USB-serial-adapters likewise incorporating
TX FIFOs as well as other terminal devices that buffer output in some
form should also provide implementations of tsw_busy.
MFC after: 3 days
on FDT/OFW platforms.
After the refactoring of the powerpc code so that OF_decode_addr() is usable
on all FDT/OFW platforms, this switches uart(4) to using it.
Differential Revision: https://reviews.freebsd.org/D4675
option to invert the polarity in software. Also add an option to capture
very narrow pulses by using the hardware's MSR delta-bit capability of
latching line state changes.
This effectively reverts the mistake I made in r286595 which was based on
empirical measurements made on hardware using TTL-level signaling, in which
the logic levels are inverted from RS-232. Thus, this re-syncs the polarity
with the requirements of RFC 2783, which is writen in terms of RS-232
signaling.
Narrow-pulse mode uses the ability of most ns8250 and similar chips to
provide a delta indication in the modem status register. The hardware is
able to notice and latch the change when the pulse width is shorter than
interrupt latency, which results in the signal no longer being asserted by
time the interrupt service code runs. When running in this mode we get
notified only that "a pulse happened" so the driver synthesizes both an
ASSERT and a CLEAR event (with the same timestamp for each). When the pulse
width is about equal to the interrupt latency the driver may intermittantly
see both edges of the pulse. To prevent generating spurious events, the
driver implements a half-second lockout period after generating an event
before it will generate another.
Differential Revision: https://reviews.freebsd.org/D4477
block. Use it in all the PNP drivers to export either the current PNP
table. For uart, create a custom table and export it using
MODULE_PNP_INFO since it's the only one that matches on function
number.
Differential Review: https://reviews.freebsd.org/D3461
It turns out on a 16550 w/ a 25MHz SoC reference clock you get a little
over 3% error at 115200 baud, which causes this to fail.
Just .. cope. Things cope these days.
Default to 30 (3.0%) as before, but allow UART_DEV_TOLERANCE_PCT to be
set at build time to change that.
vendor supplied device trees contain the needed properties for us to select
the correct uart to use as the kernel console.
An example of this would be to add the following to loader.conf.
hw.fdt.console="/smb/uart@f7113000"
The intention of this is slightly different than the existing
hw.uart.console option. The new option will mean the boot serial
configuration will be derived from the device node, while the existing
option expects the user to configure all this themselves.
Further work is planned to allow the uart configuration to be set based on
the stdout-path property devicetree bindings.
Sponsored by: ABT Systems Ltd
Differential Revision: https://reviews.freebsd.org/D3559
electrical signals on the serial port. Virtually all devices which output a
PPS signal generate a brief higher-voltage pulse, the leading edge of which
is the on-time point.
Both DCD and CTS are active-low signals on the wire, meaning the assertion
of their status bits in the modem status register corresponds to the lower
voltage level on the wire. So when the status bit transitions to not-set,
create a PPS assert event; when the status bit transitions to set, create a
PPS clear event.
eliminating the need to build a custom kernel to use the CTS signal.
The historical UART_PPS_ON_CTS kernel option is still honored, but now it
can be overridden at runtime using a tunable to configure all uart devices
(hw.uart.pps_mode) or specific devices (dev.uart.#.pps_mode). The per-
device config is both a tunable and a writable sysctl.
This syncs the PPS capabilities of uart(4) with the enhancements recently
recently added to ucom(4) for capturing from USB serial devices.
Relnotes: yes
time_pps_fetch() to be used in blocking mode.
Also, don't init the pps api for system devices (consoles) that provide a
custom attach routine. The device may actually be a keyboard or other non-
tty device. If it wants to do pps processing (unlikely) it must handle
everything for itself. (In reality, only a sun keyboard uses a custom
attach routine, and it doesn't make a good pps device.)
uart_bus_attach() during its test that 20 iterations weren't sufficient
for clearing all pending interrupts, assuming this means that hardware
is broken and doesn't deassert interrupts. However, under pressure, 20
iterations also can be insufficient for clearing all pending interrupts,
leading to a panic as intr_event_handle() tries to schedule an interrupt
handler not registered. Solve this by introducing a flag that is set in
test mode and otherwise restores pre-r253161 behavior of uart_intr(). The
approach of additionally registering uart_intr() as handler as suggested
in PR 194979 is not taken as that in turn would abuse special pccard and
pccbb handling code of intr_event_handle(). [1]
- Const'ify uart_driver_name.
- Fix some minor style bugs.
PR: 194979 [1]
Reviewed by: marcel (earlier version)
MFC after: 3 days
polling at device attach time [1].
Add tunables 'debug.uart_force_poll' and 'debug.uart_poll_freq' to control
uart polling.
Submitted by: Aleksey Kuleshov (rndfax@yandex.ru) [1]
files to vendor-provided ones. It should make easier to adopt platform
code to new revisions of hardware and to use DTS overlays for various
Beaglebone extensions (shields/capes).
Original dts filenames were not changed, they're now wrappers over dts
files provided by TI. So make sure you update .dtb files on your
devices as part of kernel update
GPIO addressing was changed: instead of one global /dev/gpioc0 there
are per-bank instances of /dev/gpiocX. Each bank has 32 pins so for
instance pin 121 on /dev/gpioc0 in old addressing scheme is now pin 25
on /dev/gpioc3
On Pandaboard serial console devices was changed from /dev/ttyu0 to
/dev/ttyu2 so you'll have to update /etc/ttys to get login prompt
on serial port in multiuser mode. Single user mode serial console
should work as-is
Differential Revision: https://reviews.freebsd.org/D2146
Reviewed by: rpaulo, ian, Michal Meloun, Svatopluk Kraus
This is needed with the pl011 driver. Before this change it would default
to a shift of 0, however the hardware places the registers at 4-byte
addresses meaning the value should be 2.
This patch fixes this for the pl011 when configured using the fdt. The
other drivers have a default value of 0 to keep this a no-op.
MFC after: 1 week
uart implementations, and export them using the new linker-set mechanism.
Differential Revision: https://reviews.freebsd.org/D1993
Submitted by: Michal Meloun
(class and device) FDT UART. Define second one, UART_FDT_CLASS, for UART
class only.
This paves the way for declaring uart_class data and ofw/fdt compat data
with a uart implementation, rather than needing a big global table of
compat data and weak-symbol declarations of every existing implementation.
Differential Revision: https://reviews.freebsd.org/D1992
Submitted by: Michal Meloun
