For _IO() ioctls, addr is a pointer to uap->data which is a caddr_t.
When the caddr_t stores an int, dereferencing addr as an (int *) results
in truncation on little-endian 64-bit systems and corruption (owing to
extracting top bits) on big-endian 64-bit systems. In practice the
value of chan was probably always zero on systems of the latter type as
all such FreeBSD platforms use a register-based calling convention.
Reviewed by: mav
Obtained from: CheriBSD
MFC after: 1 week
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D14673
As noted in the comment, UEFI spec claims the capabilities pointer is
optional, but some implementations will choke and attempt to dereference it
without checking. This specific problem was found on a Lenovo Thinkpad X220
that would panic in efirtc_identify.
On x86 the IA-PC Boot Flags in the FADT can signal whether VGA is
available or not.
Sponsored by: Citrix systems R&D
Reviewed by: marcel
Differential revision: https://reviews.freebsd.org/D14397
The gcc 7 does check for switch statement fall through cases, and if legit,
such complaint can besilenced by /* FALLTHROUGH */ comment. Unfortunately
such comment is quite limited, but will still notify the reader.
This patch is backport from illumos, see
https://www.illumos.org/rb/r/941/
Reviewed by: eadler
Differential Revision: https://reviews.freebsd.org/D14663
For each regulators create an hw.regulator.<regname>. :
uvolt: Current value
always_on: 1 If the reg is always on
boot_on: 1 If the reg is set at boot time
enable_cnt: Number of consumer(s)
enable_delay: Delay before enabling the regulator
ramp_delay: The Ramp delay
max_uamp: The maximum value of the regulator in uAmps
min_uamp: The minimal value of the regulator in uAmps
max_uvolt: The maximum value of the regulator in uVolts
min_uvolt: The minimal value of the regulator in uVolts
Reviewed by: ian
Differential Revision: https://reviews.freebsd.org/D14578
These parameters may be changed via ifconfig(8); by default,
mgt / mcast rates are lowest possible and ucast rate is not set
(matches previous configuration).
While here, store some variables locally for better readability.
this check on open, but "iscsictl -M", or an iSCSI redirect received by
iscsid(8) could end up with two sessions with the same target name and
portal.
MFC after: 2 weeks
Move copy-pasted code for RTS/CTS frame allocation into net80211.
While here, add stat / debug message for allocation failures
(copied from run(4)) + return error here in bwn(4).
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D14628
There is a difference when parsing a completion entry between Ethernet
and IB ports. When link layer is Ethernet the bits describe the type of
L3 header in the packet. In the case when link layer is Ethernet and VLAN
header is present the value of SL is equal to the 3 UP bits in the VLAN
header. If VLAN header is not present then the SL is undefined and consumer
of the completion should check if IB_WC_WITH_VLAN is set.
While that, this patch also fills the vlan_id field in the completion if
present.
linux commit 12f8fedef2ec94c783f929126b20440a01512c14
MFC after: 1 week
Sponsored by: Mellanox Technologies
mlx5core.
Do not consider the inability to create a firmware dump fatal, but
inform about the situation and allow the driver to attach. The device
might not implement the needed VSC, or we might not know the layout of
the registers map. In either case, only firmware dump functionality is
limited, the network operations should be fine.
Submitted by: kib@
MFC after: 1 week
Sponsored by: Mellanox Technologies
When the mlx5en(4) driver was converted to using BUSDMA(9) the call to
m_defrag() was moved after the part of the TX routine that strips the
header from the mbuf chain. Before it called m_defrag it first trimmed
off the now-empty mbufs from the start of the chain. This has the side
effect of also removing the head of the chain that has M_PKTHDR set.
m_defrag() will not defrag a chain that does not have M_PKTHDR set,
thus it was effectively never defragging the mbuf chains.
As it turns out, trimming the mbufs in this fashion is unnecessary since
the call to bus_dmamap_load_mbuf_sg doesn't map empty mbufs anyway, so
remove it.
Differential Revision: https://reviews.freebsd.org/D12050
Submitted by: mjoras@
MFC after: 1 week
Sponsored by: Mellanox Technologies
Set and report vport MTU rather than physical MTU,
The driver will set both vport and physical port mtu
and will rely on the query of vport mtu.
SRIOV VFs have to report their MTU to their vport manager (PF),
and this will allow them to work with any MTU they need
without failing the request.
Also for some cases where the PF is not a port owner, PF can
work with MTU less than the physical port mtu if set physical
port mtu didn't take effect.
Based on Linux upstream commit:
cd255efff9baadd654d6160e52d17ae7c568c9d3
Submitted by: Meny Yossefi <menyy@mellanox.com>
MFC after: 1 week
Sponsored by: Mellanox Technologies
Currently the ifnet interface is named mceX, where X is a monotonically
incremented value. If the device is reset due to a fatal error, then the
interface name will change. Using the device unit number will keep the
naming consistent across the reset logic.
Submitted by: Matthew Finlay <matt@mellanox.com>
MFC after: 1 week
Sponsored by: Mellanox Technologies
ConnectX-4/5 devices in mlx5core.
The dump is obtained by reading a predefined register map from the
non-destructive crspace, accessible by the vendor-specific PCIe
capability (VSC). The dump is stored in preallocated kernel memory and
managed by the mlx5tool(8), which communicates with the driver using a
character device node.
The utility allows to store the dump in format
<address> <value>
into a file, to reset the dump content, and to manually initiate the
dump.
A call to mlx5_fwdump() should be added at the places where a dump
must be fetched automatically. The most likely place is right before a
firmware reset request.
Submitted by: kib@
MFC after: 1 week
Sponsored by: Mellanox Technologies
Add the ability to access the vendor specific space gateway in order
to support reading and writing data into the different configuration
domains.
Submitted by: Matthew Finlay <matt@mellanox.com>
MFC after: 1 week
Sponsored by: Mellanox Technologies
Add support for PFC and implement reading the per priority statistics
using the sysctl(8) interface. PFC is used together with VLAN priority
and can be enabled and disabled on a per priority basis.
Global pause frames and PFC are incompatible features and surrounding
logic has been added to warn the user about misconfiguration.
Update relevant mlx5core APIs for PFC configuration.
MFC after: 1 week
Sponsored by: Mellanox Technologies
ECN configuration and statistics is available through a set of sysctl(8)
nodes under sys.class.infiniband.mlx5_X.cong . The ECN configuration
nodes can also be used as loader tunables.
MFC after: 1 week
Sponsored by: Mellanox Technologies
This patch accumulates the following Linux commits:
mlx5_health.c
- 78ccb25861d76a8fc5c678d762180e6918834200
mlx5_core: Fix wrong name in struct
- 171bb2c560f45c0427ca3776a4c8f4e26e559400
mlx5_core: Update health syndromes
- 0144a95e2ad53a40c62148f44fb0c1f9d2a0d1e9
mlx5_core: Use accessor functions to read from device memory
- ac6ea6e81a80172612e0c9ef93720f371b198918
mlx5_core: Use private health thread for each device
- fd76ee4da55abb21babfc69310d321b9cb9a32e0
mlx5_core: Fix internal error detection conditions
- 2241007b3d783cbdbaa78c30bdb1994278b6f9b9
mlx5: Clear health sick bit when starting health poll
- 712bfef60912d91033cb25739f7444d5b8d8c59f
mlx5: Fix version printout in case of health issue
- 89d44f0a6c732db23b219be708e2fe1e03ee4842
mlx5_core: Add pci error handlers to mlx5_core driver
mlx5_cmd.c
- be87544de8df2b1eb34bcb5e32691287d96f9ec4
mlx5_core: Fix async commands return code
- a31208b1e11df334d443ec8cace7636150bb8ce2
mlx5_core: New init and exit flow for mlx5_core
- 020446e01eebc9dbe7eda038e570ab9c7ab13586
mlx5_core: Prepare cmd interface to system errors handling
- 89d44f0a6c732db23b219be708e2fe1e03ee4842
mlx5_core: Add pci error handlers to mlx5_core driver
- 0d834442cc247c7b3f3bd6019512ae03e96dd99a
mlx5: Fix teardown errors that happen in pci error handler
mlx5_main.c
- 5fc7197d3a256d9c5de3134870304b24892a4908
mlx5: Add pci shutdown callback
Submitted by: Matthew Finlay <matt@mellanox.com>
MFC after: 1 week
Sponsored by: Mellanox Technologies
accomplishes a few things:
- Makes NULL an invalid address in the kernel, which is useful for catching
bugs.
- Lays groundwork for radix-tree translation on POWER9, which requires the
direct map be at high memory.
- Similarly lays groundwork for a direct map on 64-bit Book-E.
The new base address is chosen as the base of the fourth radix quadrant
(the minimum kernel address in this translation mode) and because all
supported CPUs ignore at least the first two bits of addresses in real
mode, allowing direct-map addresses to be used in real-mode handlers.
This is required by Linux and is part of the architecture standard
starting in POWER ISA 3, so can be relied upon.
Reviewed by: jhibbits, Breno Leitao
Differential Revision: D14499
Add support for mapping priority to traffic class via sysctl
Submitted by: Slava Shwartsman <slavash@mellanox.com>
MFC after: 1 week
Sponsored by: Mellanox Technologies
- Factor out port speed definitions into new port.h header file,
similarly as done in Linux upstream.
- Correct two existing port speed definitions in mlx5en according to
Linux upstream.
MFC after: 1 week
Sponsored by: Mellanox Technologies
Adding an interface might be done outside the device_attach() routine
and will then cause a panic, due to the VNET not being set.
MFC after: 1 week
Sponsored by: Mellanox Technologies
The current implementation does not handle timeout in case of command
with callback request, and this can lead to deadlock if the command
doesn't get firmware response. Add delayed callback timeout work
before posting the command to firmware. In case of real firmware
command completion we will cancel the delayed work. In case of
firmware command timeout the callback timeout handler will be called
and it will simulate firmware completion with timeout error.
linux commit 65ee67084589c1783a74b4a4a5db38d7264ec8b5
MFC after: 1 week
Sponsored by: Mellanox Technologies
Call command completion handler in case of timeout when working in
interrupts mode. Avoid flushing the commands workqueue after acquiring
the semaphores to prevent a potential deadlock.
linux commit commit 9cba4ebcf374c3772f6eb61f2d065294b2451b49
MFC after: 1 week
Sponsored by: Mellanox Technologies
