LED controller used to run the load graph on the server's front panel.
Reported by: Paul Mather <paul at gromit dot dlib dot vt dot edu>
MFC after: 3 days
sorted according to the mode which they support:
host, device or dual mode
- Add generic tool to extract these data:
tools/bus_autoconf
Discussed with: imp
Suggested by: Robert Millan <rmh@debian.org>
PR: misc/157903
MFC after: 14 days
of just setting it to the first registered device, reevaluate it for each
device registered, trying to choose best candidate, unless one was forced.
For now use such preference order: play&rec, play, rec.
As side effect, this should workaround the situation when HDMI audio output
of the video card, usually not connected to anything, becomes default, that
requires manual user intervention to make sound working. If at some point
this won't be enough, we can try to fetch some additional priority flags
from the device driver.
This brings USB bus more in line with how newbus is supposed to be used.
Also, because of the two-pass probing the following message was produced
by devd in default configuration when almost any USB device was
connected:
Unknown USB device: vendor <> product <> bus <>
This should be fixed now.
Note that many USB device drivers pass some information from probe
method to attach method via ivars. For this to continue working we rely
on the fact that the subr_bus code calls probe method of a winning driver
again before calling its attach method in the case where multiple
drivers claim to support a device. This is done because device
description is set in successful probe methods and we want to get a correct
device description from a winning driver. So now this logic is re-used
for setting ivars too.
Reviewed by: hselasky
MFC after: 1 month
Casting a pointer to a wide integer is probably not that bad, but I am
still guilty of not testing this.
Pointyhat to: avg
MFC after: 1 week
X-MFC with: r221803
This brings our implementation in line with OSS specification for
systems that support mmap. The change should also improve compatibility
with OSS software not specifically written for FreeBSD, e.g. PulseAudio
OSS plugin.
Reviewed by: kib, jhb
MFC after: 1 week
Rationale:
- unlike current behavior this seems to be compliant with OSS
specification:
http://manuals.opensound.com/developer/SNDCTL_DSP_GETIPTR.html
- this seems to meet expectations of some OSS programs compiled for or
ported from Linux, e.g. ALSA OSS plugin
- this doesn't seem to break any programs as far as current testing
shows
Tested by: nox, hselasky
MFC after: 4 days
also does this for sound drivers it's probably not necessary for all
combinations of controllers and drivers. However, given that our sound
drivers completely lack bus_dmamap_sync(9) calls this at least serves
as a workaround when enabling use of the IOMMU streaming buffers on
sparc64 and generally for arm and mips.
MFC after: 2 weeks
means of allowing vendor specific interface class for audio and MIDI devices.
- Add new quirks for this. The vendor and product list in OpenBSD's
dev/usb/umidi_quirks.c was used as reference.
MFC after: 14 days
Approved by: thompsa (mentor)
- Use the USB stack's builtin clear-stall feature.
- Wrap some long lines.
- Use memcpy() instead of bcopy().
- Use memset() instead of bzero().
- Tested applications:
/usr/ports/audio/fluidsynth
MFC after: 7 days
Approved by: thompsa (mentor)
- SMBus Controller
- SATA Controller
- HD Audio Controller
- Watchdog Controller
Thanks to Seth Heasley (seth.heasley@intel.com) for providing us code.
MFC after 3 days
the original amd64 and i386 headers with stubs.
Rename (AMD64|I386)_BUS_SPACE_* to X86_BUS_SPACE_* everywhere.
Reviewed by: imp (previous version), jhb
Approved by: kib (mentor)
configuration registers directly.
Remove pci_enable_io calls where they are redundant. The PCI bus driver
will set the right bits when the corresponding bus resource is activated.
Remove redundant pci_* function calls from suspend/resume methods. The
bus driver already saves and restores the PCI configuration.
Reviewed by: jhb
Approved by: kib (mentor)
infrastructure, not us. This appears to be a leftover from an older
version of the driver.
Submitted by: avg
Tested by: Anton Shterenlikht <mexas bristol.ac.uk>
MFC after: 1 week
X-MFC-Note: To stable/8 and stable/7 only
properly short terminate their transfers. This fixes a problem where input
appears several seconds late.
Reported by: Alexander Yerenkow
Submitted by: Hans Petter Selasky
Although the sysctls are marked with CTLFLAG_RD and the values will stay
immutable, current sysctl implementation stores value pointer in
void* type, which means that const qualifier is discarded anyway
and some newer compilers complaint about that.
We can't use de-const trick in sysctl implementation, because in that
case we could miss an opposite situation where a const value is used
with CTLFLAG_RW sysctl.
Complaint from: gcc 4.4, clang
MFC after: 2 weeks
by zero of the second argument 'from'.
- Prefer u_int32_t over unsigned int to make its intention more clearer.
- Move the function to a header file and make it a static inline function.
Pointed out by: Andrew Reilly (areilly at bigpond dot net dot au)[1]
MFC after: 3 days
On top of that, LLVM+Clang mis-compiles this code because of its register
allocator bug.
Analyzed by: Andrew Reilly (areilly at bigpond dot net dot au)
Reviewed by: ariff, rdivacky
MFC after: 3 days
volumes were incorrectly calculated.
I've tested this with one of my es1370 cards and I can confirm that it
works.
PR: 98167
Submitted by: Joseph Terner <jtsn@gmx.de>
Approved by: kib
loopback.
- Change the meaning of "mix" OSS control. Now it controls loopback level,
according to comments in soundcard.h.
- Allow AD1981HD codecs to use playback mixer. Now driver should be able to
really use it.
- Fix bug in shared muters operation.
as different nearby ones, and was grabbed by MIXER_xxx() handler.
While there, replace '(cmd & MIXER_xxx(0)) == MIXER_xxx(0)' expressions
with more correct '(cmd & ~0xff) == MIXER_READ(0)'. Use of bit operations
to compare numeric fields doesn't looks sane.
MFC after: 1 month
now due to unidentified synchonization problem. For 7.1 soundcards 5.1
support handled correctly via software upmix done by sound(4).
Stereo stream is no more duplicated to all ports. If you loose sound, check
you are using right connectors. Front speakers connector is usually green,
center/LFE - orange, rear - black, side - gray.
This replaces d_mmap() with the d_mmap2() implementation and also
changes the type of offset to vm_ooffset_t.
Purge d_mmap2().
All driver modules will need to be rebuilt since D_VERSION is also
bumped.
Reviewed by: jhb@
MFC after: Not in this lifetime...
Fix some wrong usages.
Note: this does not affect generated binaries as this argument is not used.
PR: 137213
Submitted by: Eygene Ryabinkin (initial version)
MFC after: 1 month
- fix issues regarding the mixer, where the interface number was not set in
time.
- fix wrong use of resolution parameter.
Submitted by: Hans Petter Selasky
30-bit like the reset of the controllers supported by this driver.
Actually ALi M5451 can be setup up to generate 32-bit addresses by
setting the 31st bit via the accompanying ISA bridge, which allows
it to work in sparc64 machines whose IOMMU require at least 32-bit
DMA. Even though other architectures would also benefit from 32-bit
DMA, enabling this bit is limited to sparc64 as bus_dma(9) doesn't
generally guarantee that a low address of BUS_SPACE_MAXADDR_32BIT
results in a buffer in the 32-bit range.
- According to Tatsuo YOKOGAWA's ali(4), the the DMA transfer size of
ALi M5451 is fixed to 64k and in fact using the default size of 4k
- The 4DWAVE DX and NX require the recording buffer to be 8-byte
aligned so adjust the bus_dma_tag_create(9) accordingly.
- Unlike the rest of the controllers supported by this driver, the
ALi M5451 only has 32 hardware channels instead of 64 so limit the
loop in tr_intr() accordingly. [1]
Submitted by: yongari [1]
Reviewed by: yongari (superset of what is committed)
MFC after: 3 days
The newbus lock is responsible for protecting newbus internIal structures,
device states and devclass flags. It is necessary to hold it when all
such datas are accessed. For the other operations, softc locking should
ensure enough protection to avoid races.
Newbus lock is automatically held when virtual operations on the device
and bus are invoked when loading the driver or when the suspend/resume
take place. For other 'spourious' operations trying to access/modify
the newbus topology, newbus lock needs to be automatically acquired and
dropped.
For the moment Giant is also acquired in some key point (modules subsystem)
in order to avoid problems before the 8.0 release as module handlers could
make assumptions about it. This Giant locking should go just after
the release happens.
Please keep in mind that the public interface can be expanded in order
to provide more support, if there are really necessities at some point
and also some bugs could arise as long as the patch needs a bit of
further testing.
Bump __FreeBSD_version in order to reflect the newbus lock introduction.
Reviewed by: ed, hps, jhb, imp, mav, scottl
No answer by: ariff, thompsa, yongari
Tested by: pho,
G. Trematerra <giovanni dot trematerra at gmail dot com>,
Brandon Gooch <jamesbrandongooch at gmail dot com>
Sponsored by: Yahoo! Incorporated
Approved by: re (ksmith)
This dramatically pushing 99.9% interpolations and quantizations
error _below_ -180dB on 32bit dynamic range, resulting extremely
high quality conversion.
- Use BSPLINE interpolator for filter oversampling factor greater or
equal than 64 (log2 6).
Approved by: re (kib)
This cause dramatic effect in overall precision and conversion quality
by pushing down most aliasing artifacts around -180 dB.
Spectrogram analysis/comparison:
http://people.freebsd.org/~ariff/z_comparison/z_28vs30/
- Guard against possible 64bit overflow during accumulation process by
slightly normalize and saturate sample and coefficient multiplication,
possible during extreme 32bit downsampling (eg. 380KHz -> 8KHz) with
custom preset that require more than ~7000 taps filter (which is
overkill).
- Add knobs through FEEDER_RATE_PRESETS to set dynamic range of filter
coefficients/accumulator and prefered polynomial interpolator:
COEFFICIENT_BIT:X
(where 1 <= X <= 30, default: 30)
ACCUMULATOR_BIT:X
(where 32 <= X <=64, default: 58)
INTERPOLATOR:I
(where I = ZOH, LINEAR, QUADRATIC, HERMITE, BSPLINE,
OPT32X, OPT16X, OPT8X, OPT4X, OPT2X)
Approved by: re (kib)
Note that this does not actually enable full-range i/o requests for
64 architectures, and is done now to update KBI only.
Tested by: pho
Reviewed by: jhb, bde (as part of the review of the bigger patch)
- honor parent DMA tag limitations, as man page requires,
- allow data buffer to be allocated within full 64bit address range, when
support is announced by hardware,
- add quirk, disabling 64bit addresses for broken chips, use it for MCP78.
FEEDER_RATE_PRESET "OVERSAMPLING_FACTOR:X .. .." where
X = log2(oversampling factor).
- Lower down default filter oversampling factor from 128
(log2 = 7) to 32 (log2 = 5), saving worth of 80 Kb.
The use of better polynomial interpolator will raise
its conversion quality/accuracy to match (or slightly
better) with previous settings.
- Bump driver version.
coefficients quality:
- Linear interpolator for oversampling factor larger and equal
than 4096 (log2 = 12).
- Quadratic interpolator for oversampling factor larger and equal
than 256 (log2 = 8).
Default oversampling factor (128 ~ log2 = 7) will use OPT32X, which
provides better accuracy.
For a slightly thorough explaination, please refer to
[1] http://people.freebsd.org/~ariff/SOUND_4.TXT.html .
Summary of changes includes:
1 Volume Per-Channel (vpc). Provides private / standalone volume control
unique per-stream pcm channel without touching master volume / pcm.
Applications can directly use SNDCTL_DSP_[GET|SET][PLAY|REC]VOL, or for
backwards compatibility, SOUND_MIXER_PCM through the opened dsp device
instead of /dev/mixer. Special "bypass" mode is enabled through
/dev/mixer which will automatically detect if the adjustment is made
through /dev/mixer and forward its request to this private volume
controller. Changes to this volume object will not interfere with
other channels.
Requirements:
- SNDCTL_DSP_[GET|SET][PLAY|REC]_VOL are newer ioctls (OSSv4) which
require specific application modifications (preferred).
- No modifications required for using bypass mode, so applications
like mplayer or xmms should work out of the box.
Kernel hints:
- hint.pcm.%d.vpc (0 = disable vpc).
Kernel sysctls:
- hw.snd.vpc_mixer_bypass (default: 1). Enable or disable /dev/mixer
bypass mode.
- hw.snd.vpc_autoreset (default: 1). By default, closing/opening
/dev/dsp will reset the volume back to 0 db gain/attenuation.
Setting this to 0 will preserve its settings across device
closing/opening.
- hw.snd.vpc_reset (default: 0). Panic/reset button to reset all
volume settings back to 0 db.
- hw.snd.vpc_0db (default: 45). 0 db relative to linear mixer value.
2 High quality fixed-point Bandlimited SINC sampling rate converter,
based on Julius O'Smith's Digital Audio Resampling -
http://ccrma.stanford.edu/~jos/resample/. It includes a filter design
script written in awk (the clumsiest joke I've ever written)
- 100% 32bit fixed-point, 64bit accumulator.
- Possibly among the fastest (if not fastest) of its kind.
- Resampling quality is tunable, either runtime or during kernel
compilation (FEEDER_RATE_PRESETS).
- Quality can be further customized during kernel compilation by
defining FEEDER_RATE_PRESETS in /etc/make.conf.
Kernel sysctls:
- hw.snd.feeder_rate_quality.
0 - Zero-order Hold (ZOH). Fastest, bad quality.
1 - Linear Interpolation (LINEAR). Slightly slower than ZOH,
better quality but still does not eliminate aliasing.
2 - (and above) - Sinc Interpolation(SINC). Best quality. SINC
quality always start from 2 and above.
Rough quality comparisons:
- http://people.freebsd.org/~ariff/z_comparison/
3 Bit-perfect mode. Bypasses all feeder/dsp effects. Pure sound will be
directly fed into the hardware.
4 Parametric (compile time) Software Equalizer (Bass/Treble mixer). Can
be customized by defining FEEDER_EQ_PRESETS in /etc/make.conf.
5 Transparent/Adaptive Virtual Channel. Now you don't have to disable
vchans in order to make digital format pass through. It also makes
vchans more dynamic by choosing a better format/rate among all the
concurrent streams, which means that dev.pcm.X.play.vchanformat/rate
becomes sort of optional.
6 Exclusive Stream, with special open() mode O_EXCL. This will "mute"
other concurrent vchan streams and only allow a single channel with
O_EXCL set to keep producing sound.
Other Changes:
* most feeder_* stuffs are compilable in userland. Let's not
speculate whether we should go all out for it (save that for
FreeBSD 16.0-RELEASE).
* kobj signature fixups, thanks to Andriy Gapon <avg@freebsd.org>
* pull out channel mixing logic out of vchan.c and create its own
feeder_mixer for world justice.
* various refactoring here and there, for good or bad.
* activation of few more OSSv4 ioctls() (see [1] above).
* opt_snd.h for possible compile time configuration:
(mostly for debugging purposes, don't try these at home)
SND_DEBUG
SND_DIAGNOSTIC
SND_FEEDER_MULTIFORMAT
SND_FEEDER_FULL_MULTIFORMAT
SND_FEEDER_RATE_HP
SND_PCM_64
SND_OLDSTEREO
Manual page updates are on the way.
Tested by: joel, Olivier SMEDTS <olivier at gid0 d org>, too many
unsung / unnamed heroes.
mic inputs. I have no idea what for it was made that time, but now I have
several reports that it should be removed to make microphones work. If
this quirk is still required for some systems then they should be identified
and specified explicitly.
- make usb2_power_mask_t 16-bit
- remove "usb2_config_sub" structure from "usb2_config". To compensate for this
"usb2_config" has a new field called "usb_mode" which select for which mode
the current xfer entry is active. Options are: a) Device mode only b) Host
mode only (default-by-zero) c) Both modes. This change was scripted using
the following sed script: "s/\.mh\././g".
- the standard packet size table in "usb_transfer.c" is now a function, hence
the code for the function uses less memory than the table itself.
Submitted by: Hans Petter Selasky
only for mic-type inputs. This gives better chances to use it.
Change default configuration for some AD1986A codec based ASUS boards,
use it also for ASUS P5PL2 board. This makes front mic preamplifier working.
Tested by: Vadim Frolov <frolov@frolov.ck.ua>
implement CD input in hardware, while unconditional showing it confuse users.
Also it was made in the way that sometimes improper with present driver.
Add patch for ALC268 based Acer TM5320 to make headphones jack sensing work.
Default configuration defines two separate playback associations, which
current driver unable to trace properly due to order they are defined and
limited codec uniformity.
Submitted by: G. Mirov <g.mirov AT gmail.com>
the devfs clone handler to open the (invisible) devices on the fly.
The /dev entries are layed out as follows,
/dev/usbctl = master device
/dev/usb/0.1.0.5 = usb device, (<bus>.<dev>.<iface>.<endpoint>)
/dev/ugen0.1 -> usb/0.1.0.0 = ugen link to ctrl endpoint
This also removes the custom permissions model from USB. Bump
__FreeBSD_version to 800066.
Submitted by: rink (earlier version)
Disable MSI for nVidia MCP51 controller. Enabling MSI there leads to
unexpected errors and timeouts, that should not happen even if interrupts
are not working completely.
use patches so far:
+ Envy24:
- fix: broken init data for M Audio Delta DiO 2496
- add: support for M Audio Delta 44
- add: support for M Audio Delta 1010LT
Tested by: Dominique Goncalves, dominique.goncalves at gmail.com
- add: support for Terratec EWX 2496
Tested by: Stefan Sperling, stsp at stsp.name
- add: support for M Audio Delta 66
Tested by: Richard Bown, richard.bown at blueyonder.co.uk
- add: support for M Audio Delta 1010
Tested by: Andrew Reilly, areilly at bigpond.net.au
+ Envy24HT:
- add: support for Terrasoniq TS22PCI
- fix: M-Audio Revolution 5.1 sound volume is very low
Reported by: Oliver Hartmann, ohartman at zedat.fu-berlin.de
Andrey Slusar, anrays at gmail.com
Tested by: Andrey Slusar, anrays at gmail.com
Rusu Silviu, arol.the at gmail.com
- fix: M-Audio Revolution 7.1 sound is distorted and very quiet
Reported by: Olev Hannula, hannula at gmail.com
Tested by: Olev Hannula, hannula at gmail.com
Stanislav Belansky, stanislav at icmail.ru
- fix: Terratec PHASE 22 codec is power-off due to wrong init data
Reported by: Philipp Ost, pj at smo.de
Tested by: Philipp Ost, pj at smo.de
+ SpicDS:
- fix: AK4381 produce hiss sound on 192kHz sample rate
- fix: stupid bug with volume control for AK4396
Submitted by: Konstantin Dimitrov <kosio.dimitrov@gmail.com>
solving a possible panic when snd_ai2s is loaded at boot time. Also change
the device setup to indicate to the pcm layer that the device is MPSAFE.
Submitted by: Marco Trillo
Suggestions by: Ariff Abdullah
module. These files cause manual interaction when building
ports/audio/aureal-kmod which provides a usable i386-only driver (it requires
linking against some linux object files distributed by vendor which bankrupted
back in 2000).
MFC after: 1 week
