This removes the need to set the MMC pins with pullups in our DTS.
Thanks to jmcneill@ for spotting this.
Tested on Orange Pi One (Allwinner H3).
MFC after: 1 week
GPIO_INPUT/GPIO_OUTPUT.
a10_gpio_get_pud now returns the whole pud not only PULLDOWN/PULLUP.
Add a10_gpio_get_drv to get the current drive strenght.
During fdt pin configure, avoid setting function/drive/pud if it's already in
the correct value.
Tested on Allwinner H3 and A20
MFC after: 1 week
The rootkey is burnt at production and can't be changed, thus is can be used
as a device unique ID or to generate a MAC address (This is was u-boot does).
The rootkey is exposed as a sysctl (dev.aw_sid.<unit>.rootkey).
Reviewed by: jmcneill
Differential Revision: https://reviews.freebsd.org/D6383
H3 EMAC is the same as A83T/A64 except the SoC includes an (optional)
internal 10/100 PHY. Both internal and external PHYs are supported on H3
with this driver.
- Support DEVICE_POLLING
- Increase TX descriptors to 1024
- Add support for passing a chain of mbufs to if_input, reducing the
number of calls to mtx_unlock/mtx_lock under load.
- Remove duplicate byteswap when setting TX_INT_CTL in TX descriptor.
- Set undocumented "TX_NEXT_FRAME" bit in TX control 1 register.
According to the A83T BSP, setting this bit allows the DMA engine to
operate on a packet while receiving another.
Tested on A83T (1000Mbps PHY) and H3 (100Mbps PHY).
Reviewed by: manu
Differential Revision: https://reviews.freebsd.org/D7031
on arm64 and all SoCs using the old FIFO register location are 32-bit only,
so unconditionally use the new location for arm64.
Reviewed by: andrew, manu
In some cases, the driver must handle given properties located in
specific OF subnode. Instead of creating duplicate set of function, add
'node' as argument to existing functions, defaulting it to device OF node.
MFC after: 3 weeks
Pressing the PEK (power enable key) will shutdown the board.
Some events are reported to devd via system "PMU" and subsystem
"Battery", "AC" and "USB" such as connected/disconnected.
Some sensors values (power source voltage/current) are reported via
sysctl (dev.axp209_pmu.X.)
It also expose a gpioc node usable in kernel and userland. Only 3 of
the 4 GPIO are exposed (The GPIO3 is different and mostly unused on
boards). Most popular boards uses GPIO1 as a sense pin for OTG power.
Add a dtsi file that adds gpio-controller capability to the device as
upstream doesn't defined it and include it in our custom DTS.
Reviewed by: jmcneill
Approved by: cognet (mentor)
Differential Revision: https://reviews.freebsd.org/D6135
Previously the USB PHY driver would enable all regulators at attach time.
This prevented boards from booting when powered by the USB OTG port, as
it didn't take VBUS presence into consideration.
After r285994, sysctl(8) was fixed to use 273.15 instead of 273.20 as 0C
reference and as result, the temperature read in sysctl(8) now exibits a
+0.1C difference.
This commit fix the kernel references to match the reference value used in
sysctl(8) after r285994.
Sponsored by: Rubicon Communications (Netgate)
needed in later changes where we may not be able to lock the pic list lock
to perform a lookup, e.g. from within interrupt context.
Obtained from: ABT Systems Ltd
Sponsored by: The FreeBSD Foundation
If platform support EXT_RESOURCES, clocks and resets are handled out of
the box.
If not driver can be subclassed using the generic_usb interface.
generic_usb name was choosed because at one point I'll add generic-ehci
FDT driver.
Reviewed by: jmcneill, hselasky
Approved by: andrew (mentor)
Differential Revision: https://reviews.freebsd.org/D5481
The A83T thermal sensor controller has three sensors. Sensor 0 corresponds
to CPU cluster 0, sensor 1 to CPU cluster 1, and sensor 2 to the GPU. This
driver exports the temperature sensor readings via sysctl.
Calibration data is obtained from SRAM found in the Secure ID module.
Reviewed by: manu
Differential Revision: https://reviews.freebsd.org/D6378
The RSB controller speaks a simplified two wire protocol at speeds up to
20MHz. It is used on sun8i and sun9i family SoCs to communicate with
power management ICs.
RSB isn't really I2C or SMBus, but the driver exposes an iicbus interface
to simplify power management IC drivers (which may need to support both
RSB and I2C connectivity).
This function works with all smp non-multicluster allwinner SoC (A20, A31, A31S and H3).
Approved by: cognet (mentor)
Differential Revision: https://reviews.freebsd.org/D6269
struct associated with some type defined in enum intr_map_data_type
must have struct intr_map_data on the top of its own definition now.
When such structs are used, correct type and size must be filled in.
There are three such structs defined in sys/intr.h now. Their
definitions should be moved to corresponding headers by follow-up
commits.
While this change was propagated to all INTRNG like PICs,
pic_map_intr() method implementations were corrected on some places.
For this specific method, it's ensured by a caller that the 'data'
argument passed to this method is never NULL. Also, the return error
values were standardized there.
Clocks, GPIO, UART, SD card / eMMC, USB, watchdog, and ethernet are
supported. Note that the A83T contains two clusters of four Cortex-A7
CPUs, and only CPUs in first cluster are started for now.
Tested on a Sinovoip Banana Pi BPI-M3.
The datasheets refer to this controller as EMAC, not to be confused with
the fast ethernet controller (also named EMAC) found in A10/A20 SoCs.
Tested on a BananaPi M3 (A83T), which uses an external RGMII PHY (RTL8211E).
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D6169
implementations. Early in the boot the kernel will use an approximate,
however after the timer has been probed it will switch to a more accurate
implementation.
Reviewed by: manu
Sponsored by: ABT Systems Ltd
Differential Revision: https://reviews.freebsd.org/D5762
Set MMC_CAP_4_BIT_DATA and MMC_CAP_8_BIT_DATA based on the "bus-width"
DT property and reduce maximum bus frequency from 52MHz to 50MHz to match
the capabilities of the clock provider.
Tested on a BananaPi BPI-M3 (A83T).
