handle DMA addresses located above 1GB. The LBA(loop begin address)
register which holds DMA base address is 32bits register. But the
MSB 2bits are used for other purposes. This effectivly limits the
DMA address space up to 1GB.
Approved by: jake (mentor)
Reviewed by: truckman, matk
assign DMA address to the wrong address. It can cause system lockup
or other mysterious errors. Since most sound cards requires low DMA
address(BUS_SPACE_MAXADDR_24BIT) sndbuf_alloc() would fail when the
audio driver is loaded after long running of operations.
Approved by: jake (mentor)
Reviewed by: truckman, matk
allocation. Notably, in this case, the driver tries to allocate several
pieces of memory and then fails if the pieces allocated after the first
do not come after it physically, and within a specific range (8MB I
believe). Of course, this could just as easily fail for any number of
reasons, but it almost always fails now that contiguous allocations start
at the end of possible specified memory locations rather than the beginning.
Allocate all the possibly-needed memory up front, even though it's a waste,
to get around this. The least bogus solution would be to take the physical
address from the first allocation and create a new tag that specified that
further allocations must follow it within that 8MB window, then use that
when allocating new channels, but that's left for anyone else that really
feels like doing it.
Tested by: Erwin Lansing <erwin@lansing.dk>
- `sound'
The generic sound driver, always required.
- `snd_*'
Device-dependent drivers, named after the sound module names.
Configure accordingly to your hardware.
In addition, rename the `snd_pcm' module to `sound' in order to sync
with the driver names.
Suggested by: cg
exactly as done in the cmi driver. I am quite confident this is
safe since I'm runing this for more than two weeks now, on an SMP
box. A few people tested this patch for me successfully as well.
of you with other cards, please do review and test the drivers for
MP-safety and disable Giant in the interrupt routines when you are
sure of proper functionality.
because they bogusly check for defined(INTR_MPSAFE) -- something which
never was a #define. Correct the definitions.
This make INTR_TYPE_AV finally get used instead of the lower-priority
INTR_TYPE_TTY, so it's quite possible some improvement will be had
on sound driver performance. It would also make all the drivers
marked INTR_MPSAFE actually run without Giant (which does seem to
work for me), but:
INTR_MPSAFE HAS BEEN REMOVED FROM EVERY SOUND DRIVER!
It needs to be re-added on a case-by-case basis since there is no one
who will vouch for which sound drivers, if any, willy actually operate
correctly without Giant, since there hasn't been testing because of
this bug disabling INTR_MPSAFE.
Found by: "Yuriy Tsibizov" <Yuriy.Tsibizov@gfk.ru>
read-only. Need to enable "legacy support", by poking
into pci config space. (comment from the patch)
Submited by: Autrijus Tang <autrijus@autrijus.org>
Approved by: tanimura (mentor)
This change has not been tested.
This change was triggered by a gcc(1) warning on ia64 at -O2. The
variable v was not used after being computed, which resulted in enough
dead code elimination (DCE) to confuse the compiler and emit a bogus
warning about the use of the variable i without prior definition. The
variable i is the loop variable.
Submitted by: des
Responsibility: marcel
This takes us a lot closer to refcounting dev_t.
This patch originally by cg@ with a few minor changes by me.
It is largely untested, but has been HEADSUP'ed twice, so presumably
people have not found any issues with it.
Submitted by: cg@
I started with a year-old patch by Orlando Bassotto
<orlando.bassotto@ieo-research.it>, and ported it to 5.2-CURRENT along with
fixing the problems working with pre-Audigy cards.
dsp_open: rearrange to only hold one lock at a time
dsp_close: ditto
mixer_hwvol_init: delete locking, the only consumer seems to
be the ess driver and it only call it a creation time, I
think the device will be stable across the sleepable malloc.
cmi interrupt routine: Release locks while caller chn_intr,
either this or do what emu10k1 does which is have no locks
at in the interrupt handler.
Submitted by: mat@cnd.mcgill.ca
round the result up to a multiple of 4 bytes so that it will always
be a multiple of the sample size. Also use the actual buffer size
from sc->bufsz instead of the default DS1_BUFFSIZE.
This fixes panics and bad distortion I have seen on Yamaha DS-1
hardware, mainly when playing certain Real Audio media.
Reviewed by: orion (an earlier version of the patch)
tested for playback.
* modify device name strings for ich chips to better conform with their
common names.
* remove superflous 'AC97 controller' from nforce device names.
MFC after: 1 week
Add two new arguments to bus_dma_tag_create(): lockfunc and lockfuncarg.
Lockfunc allows a driver to provide a function for managing its locking
semantics while using busdma. At the moment, this is used for the
asynchronous busdma_swi and callback mechanism. Two lockfunc implementations
are provided: busdma_lock_mutex() performs standard mutex operations on the
mutex that is specified from lockfuncarg. dftl_lock() is a panic
implementation and is defaulted to when NULL, NULL are passed to
bus_dma_tag_create(). The only time that NULL, NULL should ever be used is
when the driver ensures that bus_dmamap_load() will not be deferred.
Drivers that do not provide their own locking can pass
busdma_lock_mutex,&Giant args in order to preserve the former behaviour.
sparc64 and powerpc do not provide real busdma_swi functions, so this is
largely a noop on those platforms. The busdma_swi on is64 is not properly
locked yet, so warnings will be emitted on this platform when busdma
callback deferrals happen.
If anyone gets panics or warnings from dflt_lock() being called, please
let me know right away.
Reviewed by: tmm, gibbs
