controller. The controller is also known as L1E(AR8121) and
L2E(AR8113/AR8114). Unlike its predecessor Attansic L1,
AR8121/AR8113/AR8114 uses completely different Rx logic such that
it requires separate driver. Datasheet for AR81xx is not available
to open source driver writers but it shares large part of Tx and
PHY logic of L1. I still don't understand some part of register
meaning and some MAC statistics counters but the driver seems to
have no critical issues for performance and stability.
The AR81xx requires copy operation to pass received frames to upper
stack such that ale(4) consumes a lot of CPU cycles than that of
other controller. A couple of silicon bugs also adds more CPU
cycles to address the known hardware bug. However, if you have fast
CPU you can still saturate the link.
Currently ale(4) supports the following hardware features.
- MSI.
- TCP Segmentation offload.
- Hardware VLAN tag insertion/stripping with checksum offload.
- Tx TCP/UDP checksum offload and Rx IP/TCP/UDP checksum offload.
- Tx/Rx interrupt moderation.
- Hardware statistics counters.
- Jumbo frame.
- WOL.
AR81xx PCIe ethernet controllers are mainly found on ASUS EeePC or
P5Q series of ASUS motherboards. Special thanks to Jeremy Chadwick
who sent the hardware to me. Without his donation writing a driver
for AR81xx would never have been possible. Big thanks to all people
who reported feedback or tested patches.
HW donated by: koitsu
Tested by: bsam, Joao Barros <joao.barros <> gmail DOT com >
Jan Henrik Sylvester <me <> janh DOT de >
Ivan Brawley < ivan <> brawley DOT id DOT au >,
CURRENT ML
- Use `fildes[2]' instead of `*fildes' to make more clear that pipe(2)
fills an array with two descriptors.
- Remove EFAULT from the manual page. Because of the current calling
convention, pipe(2) raises a segmentation fault when an invalid
address is passed.
- Introduce kern_pipe() to make it easier for binary emulations to
implement pipe(2).
- Make Linux binary emulation use kern_pipe(), which means we don't have
to recover td_retval after calling the FreeBSD system call.
Approved by: rdivacky
Discussed on: arch
dependencies. A 'struct pmc_classdep' structure describes operations
on PMCs; 'struct pmc_mdep' contains one or more 'struct pmc_classdep'
structures depending on the CPU in question.
Inside PMC class dependent code, row indices are relative to the
PMCs supported by the PMC class; MI code in "hwpmc_mod.c" translates
global row indices before invoking class dependent operations.
- Augment the OP_GETCPUINFO request with the number of PMCs present
in a PMC class.
- Move code common to Intel CPUs to file "hwpmc_intel.c".
- Move TSC handling to file "hwpmc_tsc.c".
Looking at our source code history, it seems the uname(),
getdomainname() and setdomainname() system calls got deprecated
somewhere after FreeBSD 1.1, but they have never been phased out
properly. Because we don't have a COMPAT_FREEBSD1, just use
COMPAT_FREEBSD4.
Also fix the Linuxolator to build without the setdomainname() routine by
just making it call userland_sysctl on kern.domainname. Also replace the
setdomainname()'s implementation to use this approach, because we're
duplicating code with sysctl_domainname().
I wasn't able to keep these three routines working in our
COMPAT_FREEBSD32, because that would require yet another keyword for
syscalls.master (COMPAT4+NOPROTO). Because this routine is probably
unused already, this won't be a problem in practice. If it turns out to
be a problem, we'll just restore this functionality.
Reviewed by: rdivacky, kib
It is required for async cancellation to work.
Fix PROC_LOCK leak in linux_tgkill when signal delivery attempt is made
to not linux process.
Do not call em_find(p, ...) with p unlocked.
Move common code for linux_tkill() and linux_tgkill() into
linux_do_tkill().
Change linux siginfo_t definition to match actual linux one. Extend
uid fields to 4 bytes from 2. The extension does not change structure
layout and is binary compatible with previous definition, because i386
is little endian, and each uid field has 2 byte padding after it.
Reported by: Nicolas Joly <njoly pasteur fr>
Submitted by: dchangin
MFC after: 1 month
user-mode pointers. Change types used in the structures definitions to
properly-sized architecture-specific types.
Submitted by: dchagin
MFC after: 1 week
single stepped the process to the system call), we need to clear
the trap flag from the new frame. Otherwise, the new thread will
receive a (likely unexpected) SIGTRAP when it executes the first
instruction after returning to userland.
all to date and the latter also is only used in ia64 and powerpc
code which no longer serves a real purpose after bring-up and just
can be removed as well. Note that architectures like sun4u also
provide no means of implementing IPI'ing a CPU itself natively
in the first place.
Suggested by: jhb
Reviewed by: arch, grehan, jhb
After I removed all the unit2minor()/minor2unit() calls from the kernel
yesterday, I realised calling minor() everywhere is quite confusing.
Character devices now only have the ability to store a unit number, not
a minor number. Remove the confusion by using dev2unit() everywhere.
This commit could also be considered as a bug fix. A lot of drivers call
minor(), while they should actually be calling dev2unit(). In -CURRENT
this isn't a problem, but it turns out we never had any problem reports
related to that issue in the past. I suspect not many people connect
more than 256 pieces of the same hardware.
Reviewed by: kib
to the C99 style. At least, it is easier to read sysent definitions
that way, and search for the actual instances of sigcode etc.
Explicitely initialize sysentvec.sv_maxssiz that was missed in most
sysvecs.
No objection from: jhb
MFC after: 1 month
On the i386 architecture, the processor only saves the current value
of `%esp' on stack if a privilege switch is necessary when entering
the interrupt handler. Thus, `frame->tf_esp' is only valid for
an entry from user mode. For interrupts taken in kernel mode, we
need to determine the top-of-stack for the interrupted kernel
procedure by adding the appropriate offset to the current frame
pointer.
Reported by: kris, Fabien Thomas
Tested by: Fabien Thomas <fabien.thomas at netasq dot com>
code. We only attempt a single reset using this method (a "hard" reset),
and we use two writes to ensure there is a 0 -> 1 transition in bit 2 to
force a reset.
MFC after: 1 week
memory-mapped config access. Add a workaround for these systems by
checking the first function of each slot on bus 0 using both the
memory-mapped config access and the older type 1 I/O port config access.
If we find a slot that is only visible via the type 1 I/O port config
access, we flag that slot. Future PCI config transactions to flagged
slots on bus 0 use type 1 I/O port config access rather than memory mapped
config access.
location in GDT where the segment descriptor from pcb_gs32sd is
copied, and the location is in GDT local to CPU.
Noted and reviewed by: peter
MFC after: 1 week
l_ucontext. To restore the registers content, trampoline needs to
dereference uc_mcontext instead of taking some undefined values from
l_ucontext.
Submitted by: Dmitry Chagin <dchagin@>
MFC after: 1 week
processes, clear PCB_32BIT and PCB_GS32BIT bits [1].
- Reread the fs and gs bases from the msr unconditionally, not believing
the values in pcb_fsbase and pcb_gsbase, since usermode may reload
segment registers, invalidating the cache. [2].
Both problems resulted in the wrong fs base, causing wrong tls pointer
be dereferenced in the usermode.
Reported and tested by: Vyacheslav Bocharov <adeepv at gmail com> [1]
Reported by: Bernd Walter <ticsoat cicely7 cicely de>,
Artem Belevich <fbsdlist at src cx>[2]
Reviewed by: peter
MFC after: 3 days
timer. Previously, the various divisors were fixed which meant that while
it gave somewhat reasonable stathz, etc. at hz=1000, it went off the rails
with any other hz value. With these changes, we now pick a lapic timer hz
based on the value of hz. If hz is >= 1500, then the lapic timer runs at
hz. If 1500 hz >= 750, we run the lapic timer at hz * 2. If hz < 750, we
run at hz * 4. We compute a divider at runtime to make stathz run as close
to 128 as we can since stathz really wants to be run at something close to
that frequency. Profiling just runs on every clock tick. So some examples:
With hz = 100, the lapic timer now runs at 400 instead of 2000. stathz
will be 133, and profhz = 400. With hz = 1000 (default), the lapic timer
is still at 2000 (as it is now), stathz is at 133 (as it is now), and
profhz will be 2000 (previously 666).
MFC after: 2 weeks
- Rename pciereg_cfgopen() to pcie_cfgregopen() and expose it to the
rest of the kernel. It now also accepts parameters via function
arguments rather than global variables.
- Add a notion of minimum and maximum bus numbers and reject requests for
an out of range bus.
- Add more range checks on slot/func/reg/bytes parameters to the cfg reg
read/write routines. Don't panic on any invalid parameters, just fail
the request (writes do nothing, reads return -1). This matches the
behavior of the other cfg mechanisms.
- Port the memory mapped configuration space access to amd64. On amd64
we simply use the direct map (via pmap_mapdev()) for the memory mapped
window.
- During acpi_attach() just after loading the ACPI tables, check for a
MCFG table. If it exists, call pciereg_cfgopen() on each subtable
(memory mapped window). For now we only support windows for domain 0
that start with bus 0. This removes the need for more chipset-specific
quirks in the MD code.
- Remove the chipset-specific quirks for the Intel 5000P/V/Z chipsets
since these machines should all have MCFG tables via ACPI.
- Updated pci_cfgregopen() to DTRT if ACPI had invoked pcie_cfgregopen()
earlier.
MFC after: 2 weeks
The last half year I've been working on a replacement TTY layer for the
FreeBSD kernel. The new TTY layer was designed to improve the following:
- Improved driver model:
The old TTY layer has a driver model that is not abstract enough to
make it friendly to use. A good example is the output path, where the
device drivers directly access the output buffers. This means that an
in-kernel PPP implementation must always convert network buffers into
TTY buffers.
If a PPP implementation would be built on top of the new TTY layer
(still needs a hooks layer, though), it would allow the PPP
implementation to directly hand the data to the TTY driver.
- Improved hotplugging:
With the old TTY layer, it isn't entirely safe to destroy TTY's from
the system. This implementation has a two-step destructing design,
where the driver first abandons the TTY. After all threads have left
the TTY, the TTY layer calls a routine in the driver, which can be
used to free resources (unit numbers, etc).
The pts(4) driver also implements this feature, which means
posix_openpt() will now return PTY's that are created on the fly.
- Improved performance:
One of the major improvements is the per-TTY mutex, which is expected
to improve scalability when compared to the old Giant locking.
Another change is the unbuffered copying to userspace, which is both
used on TTY device nodes and PTY masters.
Upgrading should be quite straightforward. Unlike previous versions,
existing kernel configuration files do not need to be changed, except
when they reference device drivers that are listed in UPDATING.
Obtained from: //depot/projects/mpsafetty/...
Approved by: philip (ex-mentor)
Discussed: on the lists, at BSDCan, at the DevSummit
Sponsored by: Snow B.V., the Netherlands
dcons(4) fixed by: kan
kernel gs base, because %rip is adjusted only on kernel-mode trap caused
by iretq execution. On the other hand, the stack contains (hardware
part of) trap frame from the usermode. As a consequence, checking for
frame mode and doing swapgs causes the kernel to enter trap() with
usermode gs base.
Remove the check for mode and conditional swapgs, we already have right
gs base in the MSR.
Submitted by: Nate Eldredge <neldredge math ucsd edu>
MFC after: 3 days
virtualization work done by Marko Zec (zec@).
This is the first in a series of commits over the course
of the next few weeks.
Mark all uses of global variables to be virtualized
with a V_ prefix.
Use macros to map them back to their global names for
now, so this is a NOP change only.
We hope to have caught at least 85-90% of what is needed
so we do not invalidate a lot of outstanding patches again.
Obtained from: //depot/projects/vimage-commit2/...
Reviewed by: brooks, des, ed, mav, julian,
jamie, kris, rwatson, zec, ...
(various people I forgot, different versions)
md5 (with a bit of help)
Sponsored by: NLnet Foundation, The FreeBSD Foundation
X-MFC after: never
V_Commit_Message_Reviewed_By: more people than the patch
