Correct a typo in the RPI-B ethernet config - the RPi-B includes a
SMC LAN9512 USB bridge and Ethernet 10/100 NIC/phy. The phy part of
this is supported by smscphy.
Tested On: RPi1 Model B
Approved by: grog, jhb (mentors)
MFC after: 3 days
On Raspberry Pi platform GPIO controller also responsible for pins
multiplexing. Pi code predates proper FDT support in FreeBSD so a
lot of pinmux info is hardcoded. This patch:
- Implements pinctl methods in bcm2835_gpio
- Converts all devices with ad-hoc pinmux info to proper pin control
mechanisms and adds pinmux info in FreeBSD's custom dts files.
- Adds fdt_pinctrl option to RPI2 and RPI-B kernels
- Adds SPI pinmux config to FreeBSD's customization of GNU DTS.
Reviewed by: imp, manu
Differential Revision: https://reviews.freebsd.org/D14104
functionality on Raspberry Pi 0.
Reviewed by: hselasky@
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D13924
100 cycles per us seems accurate enough, at least it's better than the 200 value
that was used before.
Reviewed by: andrew, imp
Differential Revision: https://reviews.freebsd.org/D8062
All armv6 processors are plenty fast enough for HZ=1000.
No changes are made for older arm systems, because some chips are a bit
wimpy for 1000 while others do fine, so it has to be set on a per-config
basis.
BREAK_TO_DEBUGGER if they have a serial console (most do). A burst of
serial line noise (such as unplugging a usb serial adapter) can look like
a break and drop a working system into the debugger. The alt break sequence
(<CR>~^B) works fine on both serial and non-serial consoles.
each of the existing kernel configs. This gives a place to put config
that applies to the entire arch.
Add the ARM_NEW_PMAP option to std.armv6. This is working well in early
testing and it's time for wide exposure, but it's still nice to be able
to fall back to the old implementation for testing when a problem comes
along. Eventually the option and the old implementation will go away.
The opportunity now exists to move a whole lot of boilerplate from all the
arm kernel config files into std.arm*, but that's a commit for another day.
platform code, it is expected these will be merged in the future when the
ARM code is more complete.
Until more boards can be tested only use this with the Raspberry Pi and
rrename the functions on the other SoCs.
Reviewed by: ian@
in effect due to r250753. That is sufficient for all SoCs with a 32 byte
cache line size. Systems with 64 byte cache lines will need the option;
that will be done in a separate commit.
Thanks to loos@ for pointing out r250753.
this to the cache line size is required to avoid data corruption on armv4
and armv5, and improves performance on armv6, in both cases by avoiding
partial cacheline flushes for USB IO.
All these configs already exist in 10-stable. A few that don't (and
thus can't be MFC'd yet) will be committed separately.
* Make Yarrow an optional kernel component -- enabled by "YARROW_RNG" option.
The files sha2.c, hash.c, randomdev_soft.c and yarrow.c comprise yarrow.
* random(4) device doesn't really depend on rijndael-*. Yarrow, however, does.
* Add random_adaptors.[ch] which is basically a store of random_adaptor's.
random_adaptor is basically an adapter that plugs in to random(4).
random_adaptor can only be plugged in to random(4) very early in bootup.
Unplugging random_adaptor from random(4) is not supported, and is probably a
bad idea anyway, due to potential loss of entropy pools.
We currently have 3 random_adaptors:
+ yarrow
+ rdrand (ivy.c)
+ nehemeiah
* Remove platform dependent logic from probe.c, and move it into
corresponding registration routines of each random_adaptor provider.
probe.c doesn't do anything other than picking a specific random_adaptor
from a list of registered ones.
* If the kernel doesn't have any random_adaptor adapters present then the
creation of /dev/random is postponed until next random_adaptor is kldload'ed.
* Fix randomdev_soft.c to refer to its own random_adaptor, instead of a
system wide one.
Submitted by: arthurmesh@gmail.com, obrien
Obtained from: Juniper Networks
Reviewed by: obrien
