This is an extended version of ipv4_addr_IF which supports both IPv4 and
IPv6, and multiple range specifications. To avoid to generate too many
addresses, the maximum number of the generated addresses is currently
limited to 31.
- Add $ifconfig_IF_aliases, which accepts multiple IP aliases in a variable.
- ipv6_prefix_IF now supports !/64 prefix length. In addition to the old
64-bit format (2001:db8:1:1), a full 128-bit format like 2001:db8:1:1::/64
is supported.
- Replace ifconfig command with $IFCONFIG_CMD variable to support
a dry-run mode in the future.
- Remove IP aliases before removing all of IPv4 addresses when doing
"rc.d/netif down".
- Add a DAD wait to network6_getladdr() because it is possible to fail to
configure an EUI64 address when ipv6_prefix_IF is specified.
A summary of the supported ifconfig_* variables is as follows:
# IPv4 configuration.
ifconfig_em0="inet 192.168.0.1"
# IPv6 configuration.
ifconfig_em0_ipv6="inet6 2001:db8::1/64"
# IPv4 address range spec. Now deprecated.
ipv4_addr_em0="10.2.1.1-10"
# IPv6 alias.
ifconfig_em0_alias0="inet6 2001:db8:5::1 prefixlen 70"
# IPv4 alias.
ifconfig_em0_alias1="inet 10.2.2.1/24"
# IPv4 alias with range spec w/o AF keyword (backward compat).
ifconfig_em0_alias2="10.3.1.1-10/32"
# IPv6 alias with range spec.
ifconfig_em0_alias3="inet6 2001:db8:20-2f::1/64"
# ifconfig_IF_aliases is just like ifconfig_IF_aliasN.
ifconfig_em0_aliases="inet 10.3.3.201-204/24 inet6 2001:db8:210-213::1/64 inet 10.1.1.1/24"
# IPv6 alias (backward compat)
ipv6_ifconfig_em0_alias0="inet6 2001:db8:f::1/64"
# IPv6 alias w/o AF keyword (backward compat)
ipv6_ifconfig_em0_alias1="2001:db8:f:1::1/64"
# IPv6 prefix.
ipv6_prefix_em0="2001:db8::/64"
Tested by: Kimmo Paasiala
optionally start the traversal from a previously found element by passing the
element in as "var". Passing a NULL "var" retains the same semantics as the
regular FOREACH macros.
Kudos to phk for suggesting the "FROM" suffix instead of my original proposal.
Reviewed by: jhb (previous version), rpaulo
MFC after: 1 week
- remove return statements from void function [1]
- include missing header
- use O_CLOEXEC instead of separate fcntl() calls
PR: docs/179459 [1]
MFC after: 1 week
{,ipv6_}static_routes and rc.d/routing. For example:
static_routes="foo bar:em0"
route_foo="-net 10.0.0.0/24 -gateway 192.168.2.1"
route_bar="-net 192.168.1.0/24 -gateway 192.168.0.2"
At boot time, all of the static routes are installed as before.
The differences are:
- "/etc/rc.d/netif start/stop <if>" now configures static routes
with :<if> if any.
- "/etc/rc.d/routing start/stop <af> <if>" works as well. <af> cannot be
omitted when <if> is specified, but a keyword "any" or "all" can be used
for <af> and <if>.
Realtek RTL8188CU/RTL8192CU USB IEEE 802.11b/g/n wireless cards.
This driver requires microcode which is available in FreeBSD ports:
net/urtwn-firmware-kmod.
Hiren ported the urtwn(4) man page from OpenBSD and Glen just commited a port
for the firmware.
TODO:
- 802.11n support
- Stability fixes - the driver can sustain lots of traffic but has trouble
coping with simultaneous iperf sessions.
- fix debugging
MFC after: 2 months
Tested by: kevlo, hiren, gjb
QLogic 8300 Series Adapters
Submitted by: David C Somayajulu (davidcs@freebsd.org) QLogic Corporation
Approved by: George Neville-Neil (gnn@freebsd.org)
The NTB allows you to connect two systems with this device using a PCI-e
link. The driver is made of two modules:
- ntb_hw which is a basic hardware abstraction layer for the device.
- if_ntb which implements the ntb network device and the communication
protocol.
The driver is limited at the moment to CPU memcpy instead of using DMA, and
only Back-to-Back mode is supported. Also the network device isn't full
featured yet. These changes will be coming soon. The DMA change will also
bring in the ioat driver from the project branch it is on now.
This is an initial port of the GPL/BSD Linux driver contributed by Jon Mason
from Intel. Any bugs are my contributions.
Sponsored by: Intel
Reviewed by: jimharris, joel (man page only)
Approved by: jimharris (mentor)
'install' since it breaks buildworld after the introduction and
use of 'install -l' in r245752. Overriding INSTALL causes
/usr/bin/install to be used instead of the proper
/usr/src/tools/install.sh which handles the new flag.
Approved by: bapt
MFC after: 2 weeks
