mappings need to end up in the kernel anyway since the kernel begins
executing in OF context. Separating them adds needless complexity,
especially since the powerpc64 and mmu_oea64 code gave up on it a long
time ago.
As a side effect, the PPC ofw_machdep code is no longer AIM-specific,
so move it to powerpc/ofw.
work properly with single-stepping in a kernel debugger. Specifically,
these routines have always disabled interrupts before increasing the nesting
count and restored the prior state of interrupts after decreasing the nesting
count to avoid problems with a nested interrupt not disabling interrupts
when acquiring a spin lock. However, trap interrupts for single-stepping
can still occur even when interrupts are disabled. Now the saved state of
interrupts is not saved in the thread until after interrupts have been
disabled and the nesting count has been increased. Similarly, the saved
state from the thread cannot be read once the nesting count has been
decreased to zero. To fix this, use temporary variables to store interrupt
state and shuffle it between the thread's MD area and the appropriate
registers.
In cooperation with: bde
MFC after: 1 month
values to zero. A correct solution would involve emulating vector
operations on denormalized values, but this has little effect on accuracy
and is much less complicated for now.
MFC after: 2 weeks
The main goal of this is to generate timer interrupts only when there is
some work to do. When CPU is busy interrupts are generating at full rate
of hz + stathz to fullfill scheduler and timekeeping requirements. But
when CPU is idle, only minimum set of interrupts (down to 8 interrupts per
second per CPU now), needed to handle scheduled callouts is executed.
This allows significantly increase idle CPU sleep time, increasing effect
of static power-saving technologies. Also it should reduce host CPU load
on virtualized systems, when guest system is idle.
There is set of tunables, also available as writable sysctls, allowing to
control wanted event timer subsystem behavior:
kern.eventtimer.timer - allows to choose event timer hardware to use.
On x86 there is up to 4 different kinds of timers. Depending on whether
chosen timer is per-CPU, behavior of other options slightly differs.
kern.eventtimer.periodic - allows to choose periodic and one-shot
operation mode. In periodic mode, current timer hardware taken as the only
source of time for time events. This mode is quite alike to previous kernel
behavior. One-shot mode instead uses currently selected time counter
hardware to schedule all needed events one by one and program timer to
generate interrupt exactly in specified time. Default value depends of
chosen timer capabilities, but one-shot mode is preferred, until other is
forced by user or hardware.
kern.eventtimer.singlemul - in periodic mode specifies how much times
higher timer frequency should be, to not strictly alias hardclock() and
statclock() events. Default values are 2 and 4, but could be reduced to 1
if extra interrupts are unwanted.
kern.eventtimer.idletick - makes each CPU to receive every timer interrupt
independently of whether they busy or not. By default this options is
disabled. If chosen timer is per-CPU and runs in periodic mode, this option
has no effect - all interrupts are generating.
As soon as this patch modifies cpu_idle() on some platforms, I have also
refactored one on x86. Now it makes use of MONITOR/MWAIT instrunctions
(if supported) under high sleep/wakeup rate, as fast alternative to other
methods. It allows SMP scheduler to wake up sleeping CPUs much faster
without using IPI, significantly increasing performance on some highly
task-switching loads.
Tested by: many (on i386, amd64, sparc64 and powerc)
H/W donated by: Gheorghe Ardelean
Sponsored by: iXsystems, Inc.
the existing code was very platform specific, and broken for SMP systems
trying to reboot from KDB.
- Add a new PLATFORM_RESET() method to the platform KOBJ interface, and
migrate existing reset functions into platform modules.
- Modify the OF_reboot() routine to submit the request by hand to avoid
the IPIs involved in the regular openfirmware() routine. This fixes
reboot from KDB on SMP machines.
- Move non-KDB reset and poweroff functions on the Powermac platform
into the relevant power control drivers (cuda, pmu, smu), instead of
using them through the Open Firmware backdoor.
- Rename platform_chrp to platform_powermac since it has become
increasingly Powermac specific. When we gain support for IBM systems,
we will grow a new platform_chrp.
Kernel sources for 64-bit PowerPC, along with build-system changes to keep
32-bit kernels compiling (build system changes for 64-bit kernels are
coming later). Existing 32-bit PowerPC kernel configurations must be
updated after this change to specify their architecture.
(exec_setregs, etc.) in order to simplify the addition of 64-bit support,
and possible future extension of the Book-E code to handle hard floating
point and Altivec.
MFC after: 1 month
to the image_params struct instead of several members of that struct
individually. This makes it easier to expand its arguments in the future
without touching all platforms.
Reviewed by: jhb
UMA segments at their physical addresses instead of into KVA. This emulates
the direct mapping behavior of OEA32 in an ad-hoc way. To make this work
properly required sharing the entire kernel PMAP with Open Firmware, so
ofw_pmap is transformed into a stub on 64-bit CPUs.
Also implement some more tweaks to get more mileage out of our limited
amount of KVA, principally by extending KVA into segment 16 until the
beginning of the first OFW mapping.
Reported by: linimon
more. This provides three new sysctls to user space:
hw.cpu_features - A bitmask of available CPU features
hw.floatingpoint - Whether or not there is hardware FP support
hw.altivec - Whether or not Altivec is available
PR: powerpc/139154
MFC after: 10 days
while in kernel mode, and later changing signal mask to block the
signal, was fixed for sigprocmask(2) and ptread_exit(3). The same race
exists for sigreturn(2), setcontext(2) and swapcontext(2) syscalls.
Use kern_sigprocmask() instead of direct manipulation of td_sigmask to
reschedule newly blocked signals, closing the race.
Reviewed by: davidxu
Tested by: pho
MFC after: 1 month
aim/machdep.c:
- the RI status register bit needs to be set when doing the mtmsrd 64-bit
instruction test
- psim doesn't implement the dcbz instruction so the run-time cacheline
test fails. Set the cachline size to 32 to avoid infinite loops in
future calls to __syncicache()
aim/platform_chrp.c:
- if after iterating through / and a name property of "cpus" still isn't
found, just search directly for '/cpus'.
- psim doesn't put a "reg" property on it's cpu nodes, so assume 0
since it is uniprocessor-only at this point
powerpc/openpic.c
- the number of CPUs reported is 1 too many on psim's openpic
Reviewed by: nwhitehorn
MFC after: 1 week (openpic part)
possible future I-cache coherency operation can succeed. On ARM
for example the L1 cache can be (is) virtually mapped, which
means that any I/O that uses temporary mappings will not see the
I-cache made coherent. On ia64 a similar behaviour has been
observed. By flushing the D-cache, execution of binaries backed
by md(4) and/or NFS work reliably.
For Book-E (powerpc), execution over NFS exhibits SIGILL once in
a while as well, though cpu_flush_dcache() hasn't been implemented
yet.
Doing an explicit D-cache flush as part of the non-DMA based I/O
read operation eliminates the need to do it as part of the
I-cache coherency operation itself and as such avoids pessimizing
the DMA-based I/O read operations for which D-cache are already
flushed/invalidated. It also allows future optimizations whereby
the bcopy() followed by the D-cache flush can be integrated in a
single operation, which could be implemented using on-chips DMA
engines, by-passing the D-cache altogether.
new platform module. These are probed in early boot, and have the
responsibility of determining the layout of physical memory, determining
the CPU timebase frequency, and handling the zoo of SMP mechanisms
found on PowerPC.
Reviewed by: marcel, raj
Book-E parts by: raj
When memory is not zero'ed by firmware, uninitialized PCB can have bogus
contents, which appear as a saved onfault condition, Altivec context to
restore etc. and lead to corruption/crashes. This commit fixes such issues.
Submitted by: Michal Mazur arg ! semihalf dot com
Tested by: Andreas Tobler andreast-list ! fgznet dot ch
CPUs known to use 128 byte cache lines and defaulting to 32, use the dcbz
instruction to measure it. Also make dcbz behave the way you would
expect on PPC 970.
provided, for example, on the PowerPC 970 (G5), as well as on related CPUs
like the POWER3 and POWER4.
This also adds support for various built-in hardware found on Apple G5
hardware (e.g. the IBM CPC925 northbridge).
Reviewed by: grehan
of OFW access semantics, in order to allow future support for real-mode
OF access and flattened device frees. OF client interface modules are
implemented using KOBJ, in a similar way to the PPC PMAP modules.
Because we need Open Firmware to be available before mutexes can be used on
sparc64, changes are also included to allow KOBJ to be used very early in
the boot process by only using the mutex once we know it has been initialized.
Reviewed by: marius, grehan
from idle over the next tick.
- Add a new MD routine, cpu_wake_idle() to wakeup idle threads who are
suspended in cpu specific states. This function can fail and cause the
scheduler to fall back to another mechanism (ipi).
- Implement support for mwait in cpu_idle() on i386/amd64 machines that
support it. mwait is a higher performance way to synchronize cpus
as compared to hlt & ipis.
- Allow selecting the idle routine by name via sysctl machdep.idle. This
replaces machdep.cpu_idle_hlt. Only idle routines supported by the
current machine are permitted.
Sponsored by: Nokia
for better structure.
Much of this is related to <sys/clock.h>, which should really have
been called <sys/calendar.h>, but unless and until we need the name,
the repocopy can wait.
In general the kernel does not know about minutes, hours, days,
timezones, daylight savings time, leap-years and such. All that
is theoretically a matter for userland only.
Parts of kernel code does however care: badly designed filesystems
store timestamps in local time and RTC chips almost universally
track time in a YY-MM-DD HH:MM:SS format, and sometimes in local
timezone instead of UTC. For this we have <sys/clock.h>
<sys/time.h> on the other hand, deals with time_t, timeval, timespec
and so on. These know only seconds and fractions thereof.
Move inittodr() and resettodr() prototypes to <sys/time.h>.
Retain the names as it is one of the few surviving PDP/VAX references.
Move startrtclock() to <machine/clock.h> on relevant platforms, it
is a MD call between machdep.c/clock.c. Remove references to it
elsewhere.
Remove a lot of unnecessary <sys/clock.h> includes.
Move the machdep.disable_rtc_set sysctl to subr_rtc.c where it belongs.
XXX: should be kern.disable_rtc_set really, it's not MD.
after each SYSINIT() macro invocation. This makes a number of
lightweight C parsers much happier with the FreeBSD kernel
source, including cflow's prcc and lxr.
MFC after: 1 month
Discussed with: imp, rink
variable is set. On my Mac Mini this puts the CPU in NAP mode when
the kernel is idle and, any technical or environmental reasons
aside, avoids that I have to listen to the fan all day :-)
Rework of this area is a pre-requirement for importing e500 support (and
other PowerPC core variations in the future). Mainly the following
headers are refactored so that we can cover for low-level differences between
various machines within PowerPC architecture:
<machine/pcpu.h>
<machine/pcb.h>
<machine/kdb.h>
<machine/hid.h>
<machine/frame.h>
Areas which use the above are adjusted and cleaned up.
Credits for this rework go to marcel@
Approved by: cognet (mentor)
MFp4: e500
for that argument. This will allow DDB to detect the broad category of
reason why the debugger has been entered, which it can use for the
purposes of deciding which DDB script to run.
Assign approximate why values to all current consumers of the
kdb_enter() interface.
frequency from OpenFirmware moved out and into a routine that is called
from cpu_startup().
This allows correct reporting of the CPU clockspeed when printing out
CPU information at boot time.
Reported by: numerous
Reviewed by: marcel
MFC after: 1 day
silent NULL pointer dereference in the i386 and sparc64 pmap_pinit()
when the kmem_alloc_nofault() failed to allocate address space. Both
functions now return error instead of panicing or dereferencing NULL.
As consequence, vmspace_exec() and vmspace_unshare() returns the errno
int. struct vmspace arg was added to vm_forkproc() to avoid dealing
with failed allocation when most of the fork1() job is already done.
The kernel stack for the thread is now set up in the thread_alloc(),
that itself may return NULL. Also, allocation of the first process
thread is performed in the fork1() to properly deal with stack
allocation failure. proc_linkup() is separated into proc_linkup()
called from fork1(), and proc_linkup0(), that is used to set up the
kernel process (was known as swapper).
In collaboration with: Peter Holm
Reviewed by: jhb
Probabilly, a general approach is not the better solution here, so we should
solve the sched_lock protection problems separately.
Requested by: alc
Approved by: jeff (mentor)
vmcnts. This can be used to abstract away pcpu details but also changes
to use atomics for all counters now. This means sched lock is no longer
responsible for protecting counts in the switch routines.
Contributed by: Attilio Rao <attilio@FreeBSD.org>
