Commit Graph

101 Commits

Author SHA1 Message Date
Mark Johnston
159f344b84 Recognize ICS1893C PHYs.
Submitted by:	Sebastian Huber <sebastian.huber@embedded-brains.de>
MFC after:	1 week
2018-08-07 17:13:42 +00:00
Ian Lepore
b68031718e Add a driver for the Vitesse/Microsemi VSC8501 PHY. 2017-06-11 00:38:16 +00:00
Ian Lepore
e8b1516a8b Add support for the Micrel KSZ8081 ethernet PHY.
The only thing this phy needs that the ukphy driver doesn't provide is
that the value in the proprietary Phy Control 2 Register must be saved
before doing a soft reset and restored afterwards.  Most modern phys have
"sticky bits" for low-level config that survive a reset, but on this one
the values in all registers go back to defaults, wiping out any board-
specific config set up by the bootloader/bios/whatever.
2017-04-16 01:40:17 +00:00
Kevin Lo
a24d62b533 Add preliminary support for the RTL8153.
Reviewed by:	hselasky
2016-10-31 05:58:11 +00:00
Luiz Otavio O Souza
67a48226b7 Add support for the Microchip/Micrel KSZ9031 Gigabit Ethernet PHY.
Tested on uBMC and uFW.

Sponsored by:	Rubicon Communications (Netgate)
2016-07-23 18:16:40 +00:00
Baptiste Daroussin
fe56b741cc Add support for Atmel at25df641 flash
Submitted by:	Grégory Soutadé <soutade@gmail.com> (via github pull request)
2016-06-08 14:22:16 +00:00
Sean Bruno
d751decc98 Add more BCM gigabit PHYs
Gleaned from a public header file. 5402 and 5404 look like they may be
used on embedded devices. 5478 and 5488 are switch PHYs. 5754 change is just
to note a product alias.

Differential Revision:	https://reviews.freebsd.org/D3338
Submitted by:	kevin.bowling@kev009.com
2015-09-04 17:48:19 +00:00
Sean Bruno
e0fe6b4835 Add support for BCM5466 PHY
Differential Revision:	D3232
Submitted by:	kevin.bowling@kev009.com
2015-07-29 20:50:48 +00:00
Ruslan Bukin
8b62915e24 Add driver for Micrel KSZ9021 Gigabit Ethernet Transceiver (PHY).
Sponsored by:	DARPA, AFRL
2014-10-21 09:14:16 +00:00
Nathan Whitehorn
f26725de09 Add definition for the Atheros 8021 gigabit PHY.
MFC after:	1 week
2013-11-06 16:28:26 +00:00
Pyun YongHyeon
cd10b400a6 Add support for new Gigabit PHY of RealTek.
I don't have a copy of data sheet so I'm not sure exact PHY model
name. Vendor's web page indicates RTL8251 is latest PHY so I used
the name. This PHY is used with RTL8168G, RTL8168GU and RTL8411B.
2013-10-29 05:14:38 +00:00
Pyun YongHyeon
0bee427e6d Recognize BCM5725C PHY. 2013-07-20 07:24:01 +00:00
Pyun YongHyeon
0a75559c6c Recognize 5720S PHY and treat it as 5708S PHY.
Unfortunately 5720S uses 5709S PHY id so add a hack to detect 5720S
PHY by checking parent device name.  5720S PHY does not support 2500SX.

Tested by:	Geans Pin < geanspin <> broadcom dot com >
2012-12-20 05:02:12 +00:00
Oleksandr Tymoshenko
b011f8c450 Merging of projects/armv6, part 5
- Driver for SMSC LAN95XX and LAN8710A ethernet controllers
- Driver for LAN8710A PHY

Submitted by:	Ben Gray, Damjan Marion, Tim Kientzle
2012-08-15 04:03:55 +00:00
Rafal Jaworowski
9994219b7d More Cicada/Vitesse PHY ids.
Obtained from:	Semihalf
2012-05-25 15:05:17 +00:00
Marius Strobl
4bcbb398c4 Probe the National DP83849, which is a dual-port version of the PHYTER.
Obtained from:	NetBSD
2012-02-19 12:25:58 +00:00
Marius Strobl
8a731a126b - Probe BCM57780.
- In case the parent is bge(4), don't set the Jumbo frame settings unless
  the MAC actually is Jumbo capable as otherwise the PHY might not have the
  corresponding registers implemented. This is also in line with what the
  Linux tg3 driver does.

PR:		165032
Submitted by:	Alexander Milanov
Obtained from:	OpenBSD
MFC after:	3 days
2012-02-19 12:09:17 +00:00
Marius Strobl
65458598f3 Sync with NetBSD rev. 1.104
Obtained from:	NetBSD
2011-11-23 20:08:56 +00:00
Pyun YongHyeon
2d7c4b9e35 Recognize BCM5720C PHY. 2011-10-28 00:40:19 +00:00
Warner Losh
f2033ea22b Add detection for the Marvel 88E1149R and treat it just like the
88E1149.
2011-06-30 05:20:02 +00:00
Pyun YongHyeon
4c83f2f32b Recognize BCM5719C PHY.
Submitted by:	Geans Pin at Broadcom
2011-05-09 20:20:43 +00:00
Marius Strobl
3fcb7a5365 - Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP
(reporting IFM_LOOP based on BMCR_LOOP is left in place though as
  it might provide useful for debugging). For most mii(4) drivers it
  was unclear whether the PHYs driven by them actually support
  loopback or not. Moreover, typically loopback mode also needs to
  be activated on the MAC, which none of the Ethernet drivers using
  mii(4) implements. Given that loopback media has no real use (and
  obviously hardly had a chance to actually work) besides for driver
  development (which just loopback mode should be sufficient for
  though, i.e one doesn't necessary need support for loopback media)
  support for it is just dropped as both NetBSD and OpenBSD already
  did quite some time ago.
- Let mii_phy_add_media() also announce the support of IFM_NONE.
- Restructure the PHY entry points to use a structure of entry points
  instead of discrete function pointers, and extend this to include
  a "reset" entry point. Make sure any PHY-specific reset routine is
  always used, and provide one for lxtphy(4) which disables MII
  interrupts (as is done for a few other PHYs we have drivers for).
  This includes changing NIC drivers which previously just called the
  generic mii_phy_reset() to now actually call the PHY-specific reset
  routine, which might be crucial in some cases. While at it, the
  redundant checks in these NIC drivers for mii->mii_instance not being
  zero before calling the reset routines were removed because as soon
  as one PHY driver attaches mii->mii_instance is incremented and we
  hardly can end up in their media change callbacks etc if no PHY driver
  has attached as mii_attach() would have failed in that case and not
  attach a miibus(4) instance.
  Consequently, NIC drivers now no longer should call mii_phy_reset()
  directly, so it was removed from EXPORT_SYMS.
- Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe().
  The purpose of that function is to perform the common steps to attach
  a PHY driver instance and to hook it up to the miibus(4) instance and to
  optionally also handle the probing, addition and initialization of the
  supported media. So all a PHY driver without any special requirements
  has to do in its bus attach method is to call mii_phy_dev_attach()
  along with PHY-specific MIIF_* flags, a pointer to its PHY functions
  and the add_media set to one. All PHY drivers were updated to take
  advantage of mii_phy_dev_attach() as appropriate. Along with these
  changes the capability mask was added to the mii_softc structure so
  PHY drivers taking advantage of mii_phy_dev_attach() but still
  handling media on their own do not need to fiddle with the MII attach
  arguments anyway.
- Keep track of the PHY offset in the mii_softc structure. This is done
  for compatibility with NetBSD/OpenBSD.
- Keep track of the PHY's OUI, model and revision in the mii_softc
  structure. Several PHY drivers require this information also after
  attaching and previously had to wrap their own softc around mii_softc.
  NetBSD/OpenBSD also keep track of the model and revision on their
  mii_softc structure. All PHY drivers were updated to take advantage
  as appropriate.
- Convert the mebers of the MII data structure to unsigned where
  appropriate. This is partly inspired by NetBSD/OpenBSD.
- According to IEEE 802.3-2002 the bits actually have to be reversed
  when mapping an OUI to the MII ID registers. All PHY drivers and
  miidevs where changed as necessary. Actually this now again allows to
  largely share miidevs with NetBSD, which fixed this problem already
  9 years ago. Consequently miidevs was synced as far as possible.
- Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that
  weren't explicitly converted to support flow control before. It's
  unclear whether flow control actually works with these but typically
  it should and their net behavior should be more correct with these
  changes in place than without if the MAC driver sets MIIF_DOPAUSE.

Obtained from:	NetBSD (partially)
Reviewed by:	yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
Marius Strobl
2524d0a675 Probe the PHY accompanying BCM57765.
Tested by: Paul Thornton

MFC after:	1 week
2011-05-02 20:37:30 +00:00
Pyun YongHyeon
ed072c9d1a Add Realtek RTL8201E 10/100 PHY found in RTL8105E controller. The
exact model name is not clear yet. All previous RTL8201 10/100 PHYs
used 0x8201 in MII_PHYIDR2 which in turn makes model number 0x20
but this PHY used new model number 0x08.
2011-01-26 21:07:44 +00:00
Pyun YongHyeon
e6713fe53c Add RDC Semiconductor R6040 10/100 PHY driver. 2010-12-30 23:50:25 +00:00
Marius Strobl
a16ce54ca6 - Also probe BCM5214 and BCM5222.
- Add some DSP init code for BCM5221. The values derived from Apple's GMAC
  driver and the same init code also exists in Linux's sungem_phy driver.
- Only read media status bits when they are valid.

Obtained from:	NetBSD, OpenBSD
2010-11-22 22:03:11 +00:00
Juli Mallett
e875cf292c Recognize the BCM5482S. 2010-11-08 21:23:28 +00:00
Pyun YongHyeon
f8d8720ebc Add BCM5717C 10/100/1000TX PHY id. 2010-10-27 17:16:40 +00:00
Pyun YongHyeon
af1f79ce84 Add F1 PHY found on Atheros AR8151 v2.0 PCIe gigabit ethernet
controller.
2010-08-09 17:22:14 +00:00
Pyun YongHyeon
e7a28130c4 Marvell model number 0x06 is 88E1101 PHY. 2010-08-07 23:16:21 +00:00
Pyun YongHyeon
b9ddb8695d Add Marvell PHYG65G Gigabit PHY which is found on 88E8059 Yukon Optima.
Tested by:	James LaLagna < jameslalagna <> gmail dot com >
MFC after:	5 days
2010-04-30 19:01:55 +00:00
Pyun YongHyeon
500a4ded5d Add Agere ET1011 PHY which is found on Belkin F5D5055 USB
controller. Unlike Agere ET1011C, Agere ET1011 does not seem to
need special DSP programming to workaround silicon bug.
2010-04-13 20:07:52 +00:00
David Christensen
b249ff39a4 - Added support for 5709S/5716S PHYs.
Submitted by:	pyunyh
MFC after:	2 weeks
2010-03-18 20:57:57 +00:00
Joel Dahl
1edcf74de7 The NetBSD Foundation has granted permission to remove clause 3 and 4 from
the software.

Obtained from:	NetBSD
2010-03-03 17:55:51 +00:00
Marius Strobl
30b9cadca4 Add support for BCM54K2 found in combination with Apple K2 GMAC.
Submitted by:   Andreas Tobler
Obtained from:  OpenBSD
MFC after:      1 week
2010-02-20 22:01:24 +00:00
Pyun YongHyeon
ba84b911c4 Add BCM5754 PHY id that is found on Dell Studio XPS 16.
Tested by:	scf
MFC after:	1 week
2010-01-14 00:36:49 +00:00
Pyun YongHyeon
bb08f03318 Add BCM5761 PHY id. 2009-11-02 18:15:11 +00:00
Marius Strobl
21211c45f0 - Also probe DP83865, which is an is an ultra low power version
of the DP83861 and DP83891.
- Reset the PHY during attach so it's in a known state.
- Add a comment describing why we hardwire 10baseT support in
  the BMSR.
- Always explicitly set IFM_HDX for half-duplex. [1]

Obtained from:	OpenBSD [1]
MFC after:	2 weeks
2009-06-13 23:27:04 +00:00
Pyun YongHyeon
745ef56af2 Add driver support for 88E3016 PHY which is found on Marvell Yukon
FE+ controller. Due to the severe silicon bugs for Yukon FE+,
88E3016 seems to require more workarounds. However I'm not sure
whether the workaround is PHY specific or only applicable to Yukon
FE+. The datasheet for the PHY is publicly available but it lacks
several details for the workaround used in this change. The
workaround information was obtained from Linux. Many thanks to
Yukon FE+ users who helped me add 88E3016 support.

Tested by:	bz, Tanguy Bouzeloc ( the.zauron <> gmail dot com )
		Bruce Cran ( bruce <> cran dot org dot uk )
		Michael Reifenberger ( mike <> reifenberger dot com )
		Stephen Montgomery-Smith ( stephen <> missouri dot edu )
2009-05-25 02:36:29 +00:00
Warner Losh
0b5af5520d Add PHY entry for the ASIX 88x90 internal PHYs. 2009-03-30 01:47:32 +00:00
Pyun YongHyeon
b8b068386a Correct PHY description and OUI of VSC8211. Previously VSC8211 was
not recognized by ciphy(4) due to the incorrect OUI.

Reported by:	nork
Tested by:	nork
2008-10-23 01:27:15 +00:00
Stanislav Sedov
ba26d470bd - Add driver for Attansic L2 FastEthernet controller found on
Asus EeePC and some Asus mainboards.

Reviewed by:	yongari, rpaulo, jhb
Tested by:	many
Approved by:	kib (mentor)
MFC after:	1 week
2008-10-03 10:31:31 +00:00
Pyun YongHyeon
fdf7d60d6a Add Vitesse VSC8211 PHY which is found on Planex GU-1000T.
HW donated by:	nork
2008-09-30 07:30:05 +00:00
Rafal Jaworowski
d99ebc85d9 Recognize 88E1116R phy variation. This part is found on some embedded devices.
Obtained from:	Semihalf
2008-09-04 11:09:40 +00:00
Xin LI
4d52a57549 Add et(4), a port of DragonFly's Agere ET1310 10/100/Gigabit
Ethernet device driver, written by sephe@

Obtained from:	DragonFly
Sponsored by:	iXsystems
MFC after:	2 weeks
2008-06-20 19:28:33 +00:00
Benno Rice
694c651803 This is a rewritten driver for the SMSC LAN91C111. It's based in part on the
sn(4) driver and also looking at newer drivers.  The reason for the rewrite is
to support MII and to try and resolve some performance issues found when trying
to use the sn(4) driver on the Gumstix network boards.

For reference, the SMSC LAN91C111 is a non-PCI ethernet part whose lineage
dates back to Ye Olde Days of ISA.  It seems to get some use in the embedded
space these days on parts lacking on-board MACs or on-board PCI controllers,
such as the XScale PXA line of ARM CPUs.

This also includes a driver for the SMSC LAN83C183 10/100 PHY.

Man page to follow.
2008-06-06 05:00:49 +00:00
Pyun YongHyeon
6021a944af Add JMicron JMP202/JMP211 PHY driver. 2008-05-27 01:16:40 +00:00
Pyun YongHyeon
d1307e812e Add Attansic/Atheros F1 PHY driver. 2008-05-19 01:12:10 +00:00
John Baldwin
38cc658ff6 Add support for the BCM5906[M] adapters. These adapters only support
10/100 operation and place the mailbox registers at a different offset.
They also do not have an EEPROM, so the MAC address must be read from
NVRAM instead.

MFC after:	1 month
PR:		kern/118975
Submitted by:	benjsc, Thomas Nyström  thn at saeab dot se
Submitted by:	sephe (original patch for DragonflyBSD)
2008-04-29 19:47:13 +00:00
Rafal Jaworowski
324eb73387 Recognize Cicada CS8244 phy chip (among others, can be found on MPC8572DS
development systems).

Obtained from:	Freescale, Semihalf
2008-04-26 18:07:24 +00:00