Fix pull-up and pull-down values of gpio.
According to A10 user manual possible pull register
values are 00 Pull-up/down disable, 01 Pull-up, 10 Pull-down.
Approved by: gonzo@
This will be used by some upcoming changes to loader(8) FDT
handling to allow it to use an FDT provided by an earlier
boot stage the same as an FDT loaded from disk.
unnecessarily by a user thread waiting to run on a specific CPU after
calling sched_bind().
Reviewed by: rstone
Approved by: emaste (co-mentor)
Sponsored by: Sandvine Incorporated
MFC after: 1 week
submap. Otherwise, after r246204, the auto-scaling logic in kern_malloc.c
tries to create a kmem submap that consumes the entire kernel map on a
Pandaboard with 1 GB of RAM.
Tested by: gonzo
machine to another. Therefore, VM_MAX_KERNEL_ADDRESS can't be a constant.
Instead, #define it to be a variable, vm_max_kernel_address, just like we
do on sparc64.
Reviewed by: kib
Tested by: ian
is excessive. Postpone the flush of the fsinfo to VFS_SYNC(),
remembering the need for update with the flag MSDOSFS_FSIMOD, stored
in pm_flags.
FAT32 specification describes both FSI_Free_Count and FSI_Nxt_Free as
the advisory hints, not requiring them to be correct.
Based on the patch from bde, modified by me.
Reviewed by: bde
MFC after: 2 weeks
Microoptimize i8254 one-shot operation mode (disabled by default to allow
timecounter functionality) by not writing to mode and MSB registers when
it is not required. This saves several microseconds of CPU time per call,
reducing minimal measured interrupts interval to 19.5us.
points to the TLS in user space and points to the PCPU structure in
the kernel. The race is the result of having the exception handler on
the one hand and the RPC system call entry on the other. The EPC
syscall path is non-atomic in that interrupts are enabled while the
two stacks are switched. The register stack is switched last as that
is the stack used to determine whether we're going back to user space
by the exception handler. If we go back to user space, we restore r13,
otherwise we leave r13 alone. The EPC syscall path however set r13 to
the PCPU structure *before* switching the register stack, which means
that there was a window in which the exception handler would restore
r13 when it was already pointing to the PCPU structure. This is fatal
when the exception happened on CPU x, but left from the exception on
anotehr CPU. In that case r13 would point to the PCPU of the CPU the
thread was running on. This immediately results in getting the wrong
value for curthread.
The fix is to make sure we assign r13 *after* we set ar.bspstore to
point to the kernel register stack for the thread.
SDHCI driver
Suggested by: Daisuke Aoyama
- Set initilization sequence frequency to 8MHz. It should fix Data CRC
errors. Standard requires initialization sequence to be executed
at 400KHz but on this hardware low frequncies seems to cause
Data CRC errors.
Value was derived from analyzing hardware signals after
Raspberry Pi is powered up. Before any data is read though DATA line
adapter's clock frequency is changed to 8MHz.
Modern cards should function fine at 8MHz but for older MMC cards it
can be overriden by setting hw.bcm2835.sdhci.min_freq tunable.
- Replace divisor numbers with more descirptive names
- Properly calculate minimum frequency for SDHCI 3.0
- Properly calculate frequency for SDHCI 3.0 in mmcbr_set_clock
- Add min_freq method to sdhci_if.m and provide default
implementation. By re-implementing this method hardware
drivers can control frequency controller operates when
executing initialization sequence
actually do have to reinitialise the RX side of things after an RX
descriptor EOL error.
* Revert a change of mine from quite a while ago - don't shortcut the
RX initialisation path. There's a RX FIFO bug in the earlier chips
(I'm not sure when it was fixed in this series, but it's fixed
with the AR9380 and later) which causes the same RX descriptor to
be written to over and over. This causes the descriptor to be
marked as "done", and this ends up causing the whole RX path to
go very strange. This should fixed the "kickpcu; handled X packets"
message spam where "X" is consistently small.
When a cylinder group runs short of inodes, a new block for inodes is
allocated, zero'ed, and written to the disk. The zero'ed inodes must
be on the disk before the cylinder group can be updated to claim them.
If the cylinder group claiming the new inodes were written before the
zero'ed block of inodes, the system could crash with the filesystem in
an unrecoverable state.
Rather than adding a soft updates dependency to ensure that the new
inode block is written before it is claimed by the cylinder group
map, we just do a barrier write of the zero'ed inode block to ensure
that it will get written before the updated cylinder group map can
be written. This change should only slow down bulk loading of newly
created filesystems since that is the primary time that new inode
blocks need to be created.
Reported by: Robert Watson
Reviewed by: kib
Tested by: Peter Holm
write is a disk write request that tells the disk that the buffer
being written must be committed to the media along with any writes
that preceeded it before any future blocks may be written to the drive.
Barrier writes are provided by adding the functions bbarrierwrite
(bwrite with barrier) and babarrierwrite (bawrite with barrier).
Following a bbarrierwrite the client knows that the requested buffer
is on the media. It does not ensure that buffers written before that
buffer are on the media. It only ensure that buffers written before
that buffer will get to the media before any buffers written after
that buffer. A flush command must be sent to the disk to ensure that
all earlier written buffers are on the media.
Reviewed by: kib
Tested by: Peter Holm
blocking modes described in section 3.4.3 of RFC 2783, allowing the caller
to retrieve the most recent values without blocking, to block for a specified
time, or to block forever.
Reviewed by: discussion on hackers@
length packets, which was actually harmless.
Note that peers with different version of head/ may grow this
counter, but it is harmless - all pfsync data is processed.
Reported & tested by: Anton Yuzhaninov <citrin citrin.ru>
Sponsored by: Nginx, Inc
* The following bit flags where incroccetly defined:
o Mesh Control Present
o Mesh Power Save Level
o RSPI
This is now corrected according to Table 8.4 as per IEEE 802.11 2012;
Approved by: adrian (mentor)
now disables read-ahead. It used to effectively restore the system default
readahead hueristic if it had been changed; a negative value now restores
the default.
Reviewed by: kib
enumeration lock. Make sure all callers of usbd_enum_lock() check the return
value. Remove the control transfer specific lock. Bump the FreeBSD version
number, hence external USB modules may need to be recompiled due to a USB
device structure change.
MFC after: 1 week
My changed had some rather significant behavioural changes to throughput.
The two issues I noticed:
* With if_start and the ifnet mbuf queue, any temporary latency
would get eaten up by some mbufs being queued. With ath_transmit()
queuing things to ath_buf's, I'd only get 512 TX buffers before I
couldn't queue any further frames.
* There's also some non-zero latency involved with TX being pushed
into a taskqueue via direct dispatch. Any time the scheduler didn't
immediately schedule the ath TX task would cause extra latency.
Various 1ge/10ge drivers implement both direct dispatch (if the TX
lock can be acquired) and deferred task transmission (if the TX lock
can't be acquired), with frames being pushed into a drbd queue.
I'll have to do this at some point, but until I figure out how to
deal with 802.11 fragments, I'll have to wait a while longer.
So what I saw:
* lots of extra latency, specially under load - if the taskqueue
wasn't immediately scheduled, things went pear shaped;
* any extra latency would result in TX ath_buf's taking their sweet time
being replenished, so any further calls to ath_transmit() would drop
mbufs.
* .. yes, there's no explicit backpressure here - things are just dropped.
Eek.
With this, the general performance has gone up, but those subtle if_start()
related race conditions are back. For some reason, this is doubly-obvious
with the AR5416 NIC and I don't quite understand why yet.
There's an unrelated issue with AR5416 performance in STA mode (it's
fine in AP mode when bridging frames, weirdly..) that requires a little
further investigation. Specifically - it works fine on a Lenovo T40
(single core CPU) running a March 2012 9-STABLE kernel, but a Lenovo T60
(dual core) running an early November 2012 kernel behaves very poorly.
The same hardware with an AR9160 or AR9280 behaves perfectly.
thread structure pointer atomically from r13 (the pcpu pointer)
for the current CPU/core.
Add a CTASSERT in machdep.c to make sure that pc_curthread is in
fact the first field in struct pcpu.
The only non-atomic operations left were those related to process-
space operations, such as casuword, subyte, suword16, fubyte,
fuword16, copyin, copyout and their variations.
The casuword function has been re-structured more complete than
the others. This way we have an example of a better bundling
without introducing a lot of risk when we get it wrong. The
other functions can be rebundled in separate commits and with
the appropriate testing.
every architecture's busdma_machdep.c. It is done by unifying the
bus_dmamap_load_buffer() routines so that they may be called from MI
code. The MD busdma is then given a chance to do any final processing
in the complete() callback.
The cam changes unify the bus_dmamap_load* handling in cam drivers.
The arm and mips implementations are updated to track virtual
addresses for sync(). Previously this was done in a type specific
way. Now it is done in a generic way by recording the list of
virtuals in the map.
Submitted by: jeff (sponsored by EMC/Isilon)
Reviewed by: kan (previous version), scottl,
mjacob (isp(4), no objections for target mode changes)
Discussed with: ian (arm changes)
Tested by: marius (sparc64), mips (jmallet), isci(4) on x86 (jharris),
amd64 (Fabian Keil <freebsd-listen@fabiankeil.de>)
since the former is defined everywhere. This cuts off some code not
necessary on non strict aligment arches.
Reviewed by: adrian
Sponsored by: Nginx, Inc.
Fixes several problems if working with read-only pools.
Changed code originaly introduced in onnv-gate 13061:bda0decf867b
Contains changes up to illumos-gate 13700:4bc0783f6064
PR: kern/175897
Suggested by: avg
MFC after: 2 weeks
Prior to this change pinning was implemented via an ioctl (VM_SET_PINNING)
that called 'sched_bind()' on behalf of the user thread.
The ULE implementation of 'sched_bind()' bumps up 'td_pinned' which in turn
runs afoul of the assertion '(td_pinned == 0)' in userret().
Using the cpuset affinity to implement pinning of the vcpu threads works with
both 4BSD and ULE schedulers and has the happy side-effect of getting rid
of a bunch of code in vmm.ko.
Discussed with: grehan
Import vendor bugfixes regarding SA rounding, header size and layout.
This was already partially fixed by avg.
Illumos ZFS issues:
3512 rounding discrepancy in sa_find_sizes()
3513 mismatch between SA header size and layout
References:
https://www.illumos.org/issues/3512https://www.illumos.org/issues/3513
MFC after: 2 weeks
ABORT cause, since the user can also provide this kind of
information. So the receiver doesn't know who provided the
information.
While there: Fix a bug where the stack would send a malformed
ABORT chunk when using a send() call with SCTP_ABORT|SCT_SENDALL
flags.
MFC after: 3 days
of helper functions:
- carp_master() - boolean function which is true if an address
is in the MASTER state.
- ifa_preferred() - boolean function that compares two addresses,
and is aware of CARP.
Utilize ifa_preferred() in ifa_ifwithnet().
The previous version of patch also changed source address selection
logic in jails using carp_master(), but we failed to negotiate this part
with Bjoern. May be we will approach this problem again later.
Reported & tested by: Anton Yuzhaninov <citrin citrin.ru>
Sponsored by: Nginx, Inc
when they're being called from the TX completion handler.
Going (back) through the taskqueue is just adding extra locking and
latency to packet operations. This improves performance a little bit
on most NICs.
It still hasn't restored the original performance of the AR5416 NIC
but the AR9160, AR9280 and later NICs behave very well with this.
Tested:
* AR5416 STA (still tops out at ~ 70mbit TCP, rather than 150mbit TCP..)
* AR9160 hostap (good for both TX and RX)
* AR9280 hostap (good for both TX and RX)
so that simultaneous access cannot happen. Protect scratch area using
the enumeration lock. Also reduce stack usage in usbd_transfer_setup()
by moving some big stack members to the scratch area. This saves around
200 bytes of stack.
- Fix a whitespace.
MFC after: 1 week
freed memory cannot be used during detach.
- Remove all panic() calls from the urtw driver because
panic() is not appropriate here.
- Remove redundant checks for device detached in
device detach callbacks.
- Use DEVMETHOD_END to mark end of device methods.
MFC after: 2 weeks
function, implementing the sysctl vfs.ffs.set_bufoutput (not used in
the tree yet).
- The current directory vnode dereference is unsafe since fd_cdir
could be changed and unreferenced, lock the filedesc around and vref
the fd_cdir.
- The VTOI() conversion of the fd_cdir is unsafe without first
checking that the vnode is indeed from an FFS mount, otherwise
the code dereferences a random memory.
- The cdir could be reclaimed from under us, lock it around the
checks.
- The type of the fp vnode might be not a disk, or it might have
changed while the thread was in flight, check the type.
Reviewed and tested by: mckusick
MFC after: 2 weeks
tmpfs_mapped{read, write}() functions:
- tmpfs_mapped{read, write}() are only called within VOP_{READ, WRITE}(),
which check before-hand to work only on valid VREG vnodes. Also the
vnode is locked for the duration of the work, making vnode reclaiming
impossible, during the operation. Hence, vobj can never be NULL.
- Currently check on resident pages and cached pages without vm object
lock held is racy and can do even more harm than good, as a page could
be transitioning between these 2 pools and then be skipped entirely.
Skip the checks as lookups on empty splay trees are very cheap.
Discussed with: alc
Tested by: flo
MFC after: 2 weeks
* Illumos zfs issue #3035 [1] LZ4 compression support in ZFS.
LZ4 is a new high-speed BSD-licensed compression algorithm created
by Yann Collet that delivers very high compression and decompression
performance compared to lzjb (>50% faster on compression, >80% faster
on decompression and around 3x faster on compression of incompressible
data), while giving better compression ratio [1].
This version of LZ4 corresponds to upstream's [2] revision 85.
Please note that for obvious reasons this is not backward read
compatible. This means once a pool have LZ4 compressed data, these
data can no longer be read by older ZFS implementations.
Local changes:
- On-stack hash table disabled and using kernel slab allocator
instead, at this time. This requires larger kernel thread stack
for zio workers. This may change in the future should we adjusted
the zio workers' thread stack size.
- likely and unlikely will be undefined if they are already defined,
this is required for i386 XEN build.
- Removed De Bruijn sequence based __builtin_ctz family of builtins
in favor of the latter. Both GCC and clang supports these builtins.
- Changed the way the LZ4 code detects endianness.
- Manual pages modifications to mention the feature based on Illumos
counterpart.
- Boot loader changes to make it support LZ4 decompression.
[1] https://www.illumos.org/issues/3035
[2] http://code.google.com/p/lz4/source/list
Obtained from: Illumos (13921:9d721847e469)
Tested on: FreeBSD/amd64
MFC after: 1 month
e2fs_maxcontig was modelled after UFS when bringing the
"Orlov allocator" to ext2. On UFS fs_maxcontig is kept in the
superblock and is used by userland tools (fsck and growfs),
In ext2 this information is volatile so it is not available
for userland tools, so in this case it doesn't have sense
to carry it in the in-memory superblock.
Also remove a pointless check for MAX(1, x) > 0.
Submitted by: Christoph Mallon
MFC after: 2 weeks
* Add the superg.h header to allow ieee80211_check_ff() to work
* Since the assert stuff creates assertions based on line numbers and there
was a conflict, just nudge things down a bit.
crappy 802.11n performance, sigh.)
With the AR5416, aggregates need to be limited to 8KiB if RTS/CTS is
enabled. However, larger aggregates were going out with RTSCTS enabled.
The following was going on:
* The first buffer in the list would have RTS/CTS enabled in
bf->bf_state.txflags;
* The aggregate would be formed;
* The "copy over the txflags from the first buffer" logic that I added
blanked the RTS/CTS TX flags fields, and then copied the bf_first
RTS/CTS flags over;
* .. but that'd cause bf_first to be blanked out! And thus the flag
was cleared;
* So the rest of the aggregate formation would run with those flags
cleared, and thus > 8KiB aggregates were formed.
The driver is now (again) correctly limiting aggregate formation for
the AR5416 but there are still other pending issues to resolve.
Tested:
* AR5416, STA mode
A special gfs vnode corresponds to that object.
A regular zfs vnode must not be returned.
This should be upstreamed.
Reported by: pluknet
Submitted by: rmacklem
Tested by: pluknet
MFC after: 10 days
Older entries should be 'before' newer entries in the new buffer too
and there should be no zero-filled gap between them.
Pointed out by: jhb
MFC after: 3 days
X-MFC with: r246282
* Added hwmp_update_transmitter function that checks if the metric
to the transmitter have improved. If old FI is invalid or metric
is larger the FI to the transmitter is updated occurdingly.
This is a recommendation from the 802.11 2012 standard, table 13-9;
Approved by: adrian (mentor)
* When calling ieee80211_mesh_rt_flush_peer, the rt->rt_dest argument
should not be passed because it can get freed before invalidating
the other routes that depends on it to compare with next_hop.
Use PERR_DADDR(i) instead;
Approved by: adrian (mentor)
* The standard is unclear about what should happen in case a mesh STA (not
marked as a mesh gate) recevies a PREQ for a destination that is marked
as proxy. Solution for now is not to do intermediate reply at all, and
let the PREQ reach the mesh gate;
Approved by: adrian (mentor)
* Original PREP frame is transmitted only by the target mesh STA or the
mesh STA that is the proxy target;
* Fixed so that metric value is not over written incorrectly in
hwmp_recv_preq for when replying back with a PREP;
Approved by: adrian (mentor)
This is a code re-write. ic->raw_xmit need a pointer to ieee80211_node
for the destination node (da). I have reorganized the code so that
a pointer to the da node is searched for in the end & in one place.
* Make mesh_find_txnode public to be used by HWMP, renamed to
ieee80211_mesh_finx_txnode;
* changed the argument from ieee80211_node to ieee80211vap for all
hwmp_send_* functions;
* removed the 'sa' argument from hwmp_send_* functions as all HWMP frames
have the source address equal to vap->iv_myaddr;
* Modified hwmp_send_action so that if da is MULTCAST ni=vap->iv_bss
otherwise we called ieee80211_mesh_find_txnode. Also no need to hold
a reference in this functions if da is not MULTICAST as by finding the
node it became referenced in ieee80211_find_txnode;
Approved by: adrian (mentor)
* Modified mesh_find_txnode to be able to handle proxy marked entries by
recursively calling itself to find the txnode towards the active mesh gate;
* Mesh Gate: Added a new function that transmits data frames
similar to ieee80211_start;
* Modified ieee80211_mesh_forward_to_gates so that:
+ Frames are duplicated and sent to each valid Mesh Gate;
+ Route is marked invalid before return of function, this is
because we dont know yet which Mesh Gate is we will use;
Approved by: adrian (mentor)
* Send frames that have no path to a known valid Mesh Gate;
* Added the function ieee80211_mesh_forward_to_gates that sends the frame
to the first found Mesh Gate in the forwarding information;
* If we try to discover again while we are discovering queue frame,
the discovery callout will send the frames either to mesh gates
or discards them silently;
* Queue frame also if we try to discover to frequently;
Approved by: adrian (mentor)
* Add function ieee80211_mesh_mark_gate in ieee80211_mesh.h;
* When received a proactive PREQ or RANN with corresponding mesh gate
flag set, create a new entry in the known mesh gate list;
Approved by: adrian (mentor)
* Modified mesh_recv_action_meshgate to do following:
+ if mesh STA already knows the mesh gate of the recevied GANN frame
+ if mesh gate is know, check seq number according to 802.11 standard
+ if mesh gate is not know, add it to the list of known mesh gates
+ if forwarding is enabled and ttl >= 1 then propagate the GANN frame;
* Declare a new malloc type M_80211_MESH_GT_RT;
* Declare a struct to store GANN information, ieee80211_mesh_gate_route. And
add it as a TAILQ list to ieee80211_mesh_state;
Approved by: adrian (mentor)
A Mesh Gate should transmit a Mesh Action frame containing
ieee80211_meshgann_ie as its only information element periodically
every ieee80211_mesh_gateint ms. Unless the mesh gate is also configure
as a ROOT, then these frames should not be send.
This is according to 802.11 2012 standard;
* Introduce new SYSCTL net.wlan.mesh.gateint, with 10s default;
* Add two new functions mesh_gatemode_setup and mesh_gatemode_cb. This
is similar to how HWMP setups up a callout;
* Add two new action handlers mesh_recv_action_meshgate and
mesh_send_action_meshgate;
* Added ieee80211_add_meshgate to ieee80211_mesh.h;
* Modified mesh_send_action to look similar to hwmp_send_action. This is
because we need to send out broadcast management frames.
* Introduced a new flag for mesh state IEEE80211_MESHFLAGS_ROOT. This flag
is now set by HWMP code when a mesh STA is configured as a ROOT. This
is then checked by mesh_gatemode_cb before scheduling a new callout;
* Added to new field to ieee80211_mesh_state:
+ struct callout ms_gatetimer
+ ieee80211_mesh_seq ms_gateseq;
Approved by: adrian (mentor)
when not peered.
* Modified ieee80211_recv_action to check if neighbour is peered for
IEEE80211_ACTION_CAT_MESH frames, if not frame is discarded. This is
according to IEEE802.11 2012 standard;
* Removed duplicate checks in each hwmp_recv_* handlers because HWMP
is a subtype of mesh action;
Approved by: adrian (mentor)
* Removed meshlm_send_action and hwmp_send_action. Introduced one common
for all Mesh Action frames meshaction_send_action. According to 802.11
standard Link Metric and HWMP are all under Mesh Action category;
* Did similar changes to recv_action part;
* The size of meshaction_*_action is set to 12. This is to make room for
the rest of Mesh Action category subtypes;
Approved by: adrian (mentor)
* Change all field prefix from pann_ to gann_;
* Added IEEE80211_MESHGANN_BASE_SZ macro to be used in the length field
of a GANN frame according to 802.11 standard;
* Changed gann_seq field type to uint32_t;
* Added a Gate Announcement interval field according to
IEEE802.11 2012 standard;
* Added IEEE80211_MESHRT_FLAGS_GATE as flag bit to ieee80211_mesh_route;
* Added IEEE80211_MESHRT_FLAGS_GATE as flag bit to ieee80211req_mesh_route;
Approved by: adrian (mentor)
* An HWMP PERR should be accepted even if path is valid. Because
we check if we recevied it from a neighbour that we use as a next hop;
Approved by: adrian (mentor)
* A bug occurs while in discovery mode which leaves a path marked with
both Discover and Valid flag. This happens when receiving/sending
PREQ and PREP in a particular order. Solution is to assign the Valid bit
instead of oring it;
Approved by: adrian (mentor)
This problem happens when using ACL policy to filter mesh STA
but two nodes have different policy. Then one of them will try to
peer all the time. This can also help if for any reason one of the
peering mesh STA have problems sending/receiving peer frames.
* Modified struct ieee80211_node to include two new fields:
+ struct callout ni_mlhtimer /* link mesh backoff timer */
+ uint8_t ni_mlhcnt /* link mesh holding counter */
* Added two new sysctl (check sysctl -d for more info):
+ net.wlan.mesh.backofftimeout=5000
+ net.wlan.mesh.maxholding=2;
* When receiving a beacon and we are in IEEE80211_NODE_MESH_IDLE
check if ni_mlhcnt >= ieee80211_mesh_maxholding, if so do not do anything;
* In mesh_peer_timeout_cb when transitioning from IEEE80211_NODE_MESH_HOLDING
to IEEE80211_NODE_MESH_IDLE increment ni_mlhcnt, and eventually start
ieee80211_mesh_backofftimeout;
Approved by: adrian (mentor)
until child performs exec(). The behaviour is reasonable when a
debugger is the real parent, because the parent is stopped until
exec(), and sending a debugging event to the debugger would deadlock
both parent and child.
On the other hand, when debugger is not the parent of the vforked
child, not sending debugging signals makes it impossible to debug
across vfork.
Fix the issue by declining generating debug signals only when vfork()
was done and child called ptrace(PT_TRACEME). Set a new process flag
P_PPTRACE from the attach code for PT_TRACEME, if P_PPWAIT flag is
set, which indicates that the process was created with vfork() and
still did not execed. Check P_PPTRACE from issignal(), instead of
refusing the trace outright for the P_PPWAIT case. The scope of
P_PPTRACE is exactly contained in the scope of P_PPWAIT.
Found and tested by: zont
Reviewed by: pluknet
MFC after: 2 weeks
of the newer drivers. The basic problem was
that the driver was pulling the mbuf off the
drbr ring and then when sending with xmit(), encounting
a full transmit ring. Thus the lower layer
xmit() function would return an error, and the
drivers would then append the data back on to the ring.
For TCP this is a horrible scenario sure to bring
on a fast-retransmit.
The fix is to use drbr_peek() to pull the data pointer
but not remove it from the ring. If it fails then
we either call the new drbr_putback or drbr_advance
method. Advance moves it forward (we do this sometimes
when the xmit() function frees the mbuf). When
we succeed we always call advance. The
putback will always copy the mbuf back to the top
of the ring. Note that the putback *cannot* be used
with a drbr_dequeue() only with drbr_peek(). We most
of the time, in putback, would not need to copy it
back since most likey the mbuf is still the same, but
sometimes xmit() functions will change the mbuf via
a pullup or other call. So the optimial case for
the single consumer is to always copy it back. If
we ever do a multiple_consumer (for lagg?) we
will need a test and atomic in the put back possibly
a seperate putback_mc() in the ring buf.
Reviewed by: jhb@freebsd.org, jlv@freebsd.org
Posix requires that open(2) is restartable for SA_RESTART.
For non-posix objects, in particular, devfs nodes, still disable
automatic restart of the opens. The open call to a driver could have
significant side effects for the hardware.
Noted and reviewed by: jilles
Discussed with: bde
MFC after: 2 weeks
cpuset mask for the associated interrupt thread.
The text used above is verbatim from r195249 and the code should now be
in line with the intent of that commit.
195702, 195703, and 195821 prevented a thread from suspending while holding
locks inside of NFS by forcing the thread to fail sleeps with EINTR or
ERESTART but defer the thread suspension to the user boundary. However,
this had the effect that stopping a process during an NFS request could
abort the request and trigger EINTR errors that were visible to userland
processes (previously the thread would have suspended and completed the
request once it was resumed).
This change instead effectively masks stop signals while in the NFS client.
It uses the existing TDF_SBDRY flag to effect this since SIGSTOP cannot
be masked directly. Also, instead of setting PBDRY on individual sleeps,
the NFS client now sets the TDF_SBDRY flag around each NFS request and
stop signals are masked for all sleeps during that region (the previous
change missed sleeps in lockmgr locks). The end result is that stop
signals sent to threads performing an NFS request are completely
ignored until after the NFS request has finished processing and the
thread prepares to return to userland. This restores the behavior of
stop signals being transparent to userland processes while still
preventing threads from suspending while holding NFS locks.
Reviewed by: kib
MFC after: 1 month
using /dev/consolectl close. This fixes a problem where if
a USB mouse is detached while a button is pressed, that
button is never released.
MFC after: 1 week
- Add const quilifiers to fields that store value of __FILE__.
- Use long type for fields that store value of __LINE__.
- Sort and style(9) debugging fields.
- Add initializer for debugging fields into TAILQ_INITIALIZER macro.
PR: 175759
Submitted by: Andrey Simonenko <simon comsys.ntu-kpi.kiev.ua>
Reviewed by: bde
This eliminates the need to recompile the kernel when the default value
of NKPT is not big enough - for e.g. when loading large kernel modules
or memory disk images from the loader.
If NKPT is defined in the kernel configuration file then it overrides the
dynamic calculation.
Reviewed by: alc, kib
requires 8 bytes alignment on RX buffer. Given that non-jumbo
frame works on any alignments I guess this DMA limitation for RX
buffer could be jumbo frame specific one. Also I'm not sure
whether this DMA limitation is related with 64bit DMA. Previously
age(4) disabled 64bit DMA addressing due to silent data corruption.
So we may need more testing on re-enabling 64bit DMA in future.
While I'm here, change mbuf chaining algorithm to use fixed sized
buffer and force software checksum if controller reports length
error. According to QAC, RFD is not updated at all for jumbo frame
so it works just like alc(4) controllers. This change also added
alignment fixup for strict alignment architectures. Because I'm
not aware of any non-x86 machines that use age(4) controllers it's
just for completeness at this moment.
Wit this change, jumbo frame should work with age(4).
Tested by: Christian Gusenbauer < c47g <> gmx dot at >
MFC after: 1 week
The check is copied from vnet_ng_ether_init.
Not sure if it covers all the types that we want to support with
ng_ether.
Reported by: markj
Discussed with: zec
MFC after: 10 days
X-MFC with: r246245
Now they are split into two pairs: page_hold/page_unhold for mappedread
and page_busy/page_unbusy for update_pages.
For mappedread we simply hold a page that is to be used as a source if it
is resident and valid (and not busy). This is sufficient since we are
only doing page -> user buffer copying. There is no page <-> backing
storage I/O involved.
update_pages is now better split to properly handle the putpages case
(page -> arc) and the regular write case (arc -> page).
For the latter we use complete protocol of marking an object with
paging-in-progress and marking a page with io_start (busy count).
Also, in this case we remove the write bit from all page mappings and
clear dirty bits of the pages, the former is needed to ensure that the
latter does the right thing.
Additionally we update a page if it is cached instead of just freeing it
as was done before. This needs to be verified.
A minor detail: ZFS-backed pages should always be either fully valid
or fully invalid. Assert this and use simpler API that does not deal
with sub-page blocks.
Reviewed by: kib
MFC after: 26 days
has gone below zero after the blocks in its inode are freed is a
no-op which the compiler fails to warn about because of the use of
the DIP macro. Change the sanity check to compare the number of
blocks being freed against the value i_blocks. If the number of
blocks being freed exceeds i_blocks, just set i_blocks to zero.
Reported by: Pedro Giffuni (pfg@)
MFC after: 2 weeks
Only during very early boot, before malloc(9) is functional (SI_SUB_KMEM),
the static ktr_buf_init is used. Size of the static buffer is determined
by a new kernel option KTR_BOOT_ENTRIES. Its default value is 1024.
This commit builds on top of r243046.
Reviewed by: alc
MFC after: 17 days
Major changes:
* Finally tracked down the flow control setting that
seems to have been causing TX stalls and watchdog timeouts
* RX and TX paths now share a lot more code
* TX interrupt is no longer used; we instead GC finished
tx queue entries at the bottom of the start routine.
* TX start now queues fragmented packets directly; it only
invokes defrag() for occasional very fragmented packets.
* "sysctl dev.cpsw" dumps controller statistics and queue counts
* Host Error Interrupt will give extensive debugging information
if the controller chokes on the queued data.
- Remove unused extern declarations in fs.h
- Correct comments in ext2_dir.h
- Several panic() messages showed wrong function names.
- Remove commented out stray line in ext2_alloc.c.
- Remove the unused macro EXT2_BLOCK_SIZE_BITS() and the then
write-only member e2fs_blocksize_bits from struct m_ext2fs.
- Remove the unused macro EXT2_FIRST_INO() and the then write-only
member e2fs_first_inode from struct m_ext2fs.
- Remove EXT2_DESC_PER_BLOCK() and the member e2fs_descpb from
struct m_ext2fs.
- Remove the unused members e2fs_bmask, e2fs_dbpg and
e2fs_mount_opt from struct m_ext2fs
- Correct harmless off-by-one error for fspath in ext2_vfsops.c.
- Remove the unused and broken macros EXT2_ADDR_PER_BLOCK_BITS()
and EXT2_DESC_PER_BLOCK_BITS().
- Remove the !_KERNEL versions of the EXT2_* macros.
Submitted by: Christoph Mallon
MFC after: 2 weeks
passed in by smartd of smartmontools.
While at it, hint the compiler that 32-bit PIO is the most likely
case (idea from Linux) and use bus_{read,write}_stream_2(9) instead
of bus_{read,write}_multi_stream_2(9) for single count reads/writes.
MFC after: 1 week
This hack is picked up from Linux, which claims that it follows
Windows behavior.
PR: amd64/174409
Tested by: Sergey V. Dyatko <sergey.dyatko@gmail.com>,
KAHO Toshikazu <kaho@elam.kais.kyoto-u.ac.jp>,
Slawa Olhovchenkov <slw@zxy.spb.ru>
MFC after: 13 days
- change 'pics' from STAILQ to TAILQ
- ensure that Local APIC is always first in 'pics'
Reviewed by: jhb
Tested by: Sergey V. Dyatko <sergey.dyatko@gmail.com>,
KAHO Toshikazu <kaho@elam.kais.kyoto-u.ac.jp>
MFC after: 12 days
And provide kernel compiler version as a sysctl as well.
This is useful while we have gcc and clang cohabitation.
This could be even more useful when we have support
for external toolchains.
In cooperation with: mjg
MFC after: 13 days
Also sanitize interface names that can potentially contain characters
that are prohibited in netgraph names.
PR: kern/154850 (sanitizing of names)
Discussed with: eri, melifaro
Submitted by: Nikolay Denev <ndenev@gmail.com> (sanitizing code)
Reviewed by: eri, glebius
MFC after: 17 days
- there is no such flag in Solaris and derivatives
- the flag was added in an unrelated change
- the flag is not used
The proper way to allocate zeroed out memory is to use kmem_zalloc.
MFC after: 3 days
x86 buses
Otherwise the uart hardware could be in such a state after the resume
where IER is cleared and thus no interrupts are generated.
This behavior is observed and tested with QEMU, so I am comitting this
change to help with my debugging.
There has been no feedback from users of serial ports on real hardware.
MFC after: 20 days
This should allow the kernel linker to easily detect a situation
when the module is present both in a kernel and in a preloaded file
(zfs.ko).
Reviewed by: jhb
MFC after: 5 days
track the MNT_SYNCHRONOUS flag. It is set to the latter at mount time
but not updated by MNT_UPDATE.
Use MNT_SYNCHRONOUS to decide to write the FAT updates syncrhonously.
Submitted by: bde
MFC after: 1 week
a directory to a subdir of the root directory from somewhere else.
For all directory moves that change the parent directory, the dotdot
entry must be fixed up. For msdosfs, the root directory is magic for
non-FAT32. It is less magic for FAT32, but needs the same magic for
the dotdot fixup. It didn't have it.
Both chkdsk and fsck_msdosfs fix the corrupt directory entries with no
problems.
The fix is to use the same magic for dotdot in msdosfs_rename() as in
msdosfs_mkdir().
For msdosfs_mkdir(), document the magic. When writing the dotdot entry
in mkdir, use explicitly set pcl variable instead on relying on the
start cluster of the root directory typically has a value < 65536.
Submitted by: bde
MFC after: 1 week
Trying FAT32 on a small partition failed to mount because
pmp->pm_Sectors was nonzero. Normally, FAT32 file systems are so
large that the 16-bit pm_Sectors can't hold the size. This is
indicated by setting it to 0 and using only pm_HugeSectors. But at
least old versions of newfs_msdos use the 16-bit field if possible,
and msdosfs supports this except for breaking its own support in the
sanity check. This is quite different from the handling of pm_FATsecs
-- now the 16-bit value is always ignored for FAT32 except for
checking that it is 0, and newfs_msdos doesn't use the 16-bit value
for FAT32.
Submitted by: bde
MFC after: 1 week
this check is somewhere in the network code, but this assertion
already proven to be useful in catching what seems to be driver bugs
causing NFS scrambling random memory.
Discussed with: rmacklem
MFC after: 1 week
zero on slower machines, which make the fenced get_timecount methods
not used despite needed. Remove the (shift > 0) condition when
selecting the get_timecount() implementation.
Rename smp_tsc_shift to tsc_shift, and apply it for the UP case too.
Allow shift to reach value of 31 instead of 30, as it was previously
(should be nop).
Reorganize the tc quality calculation to remove the conditionally
compiled block. Rename test_smp_tsc() to test_tsc() and provide
separate versions for SMP and UP builds. The check for virtialized
hardware is more natural to perform in the smp version of the
test_tsc(), since it is only done for smp case.
Noted and reviewed by: bde (previous version)
MFC after: 12 days
VM_KMEM_SIZE_SCALE specifies which fraction of the available physical
memory, after deduction of the kernel itself and other early statically
allocated memory, can be used for the kmem_map. The kmem_map provides
for all UMA/malloc allocations in KVM space.
Previously ARM was using a fixed kmem_map size of (12*1024*1024) = 12MB
without regard to effectively available memory. This is too small for
recent ARM SoC with more than 128MB of RAM.
For reference a description of others related kmem_map parameters:
VM_KMEM_SIZE default start size of kmem_map if SCALE is
not defined
VM_KMEM_SIZE_MIN hard floor on the kmem_map size
VM_KMEM_SIZE_MAX hard ceiling on the kmem_map size
VM_KMEM_SIZE_SCALE fraction of the available real memory to
be used for the kmem_map, limited by the
MIN and MAX parameters.
Tested by: ian
MFC after: 1 week
The "blackhole" driver was used in conjunction with bhyve to sequester
pci devices intended for passthru until vmm.ko was loaded. This was
useful at one point because vmm.ko could not be loaded at boot time.
The same functionality can now be achieved by loading vmm.ko via the
loader along with the kernel.
Discussed with: grehan
Obtained from: NetApp
can only be located at the beginning or the end of the BAR.
If the MSI-table is located in the middle of a BAR then we will split the
BAR into two and create two mappings - one before the table and one after
the table - leaving a hole in place of the table so accesses to it can be
trapped and emulated.
Obtained from: NetApp
The maximum length of an environment variable puts a limitation on the
number of passthru devices that can be specified via a single variable.
The workaround is to allow user to specify passthru devices via multiple
environment variables instead of a single one.
Obtained from: NetApp
case 0x3E: /* Per Intel document 325462-045US 01/2013. */
Add manpage to document all the goodness that is available in this
processor model.
No support for uncore events at this time.
Submitted by: hiren panchasara <hiren.panchasara@gmail.com>
Reviewed by: davide, jimharris, sbruno
Obtained from: Yahoo! Inc.
MFC after: 2 weeks
Since ARP and routing are separated, "proxy only" entries
don't have any meaning, thus we don't need additional field
in sockaddr to pass SIN_PROXY flag.
New kernel is binary compatible with old tools, since sizes
of sockaddr_inarp and sockaddr_in match, and sa_family are
filled with same value.
The structure declaration is left for compatibility with
third party software, but in tree code no longer use it.
Reviewed by: ru, andre, net@
Right now, ic_curchan seems to be updated rather quickly (ie, during
the ioctl) and before the driver gets notified of what's going on.
So what I was seeing was:
* NIC was in channel X;
* It generates PHY errors for channel X;
* an ioctl comes along from userland and changes things to channel Y;
* .. this updates ic_curchan, but hasn't yet reset the hardware;
* in parallel, RX is occuring and it looks at ic_curchan;
* .. which is channel Y, so events get stamped with that now.
Sigh.
into the FreeBSD boot loader, typically for non-USB aware BIOSes, EFI systems
or embedded platforms. This is also useful for out of the system compilation
of the FreeBSD USB stack for various purposes. The USB kernel files can
now optionally include a global header file which should include all needed
definitions required to compile the FreeBSD USB stack. When the global USB
header file is included, no other USB header files will be included by
default.
Add new file containing the USB stack configuration for the
FreeBSD loader build.
Replace some __FBSDID()'s by /* $FreeBSD$ */ comments. Now all
USB files follow the same style.
Use cases:
- console in loader via USB
- loading kernel via USB
Discussed with: Hiroki Sato, hrs @ EuroBSDCon
in kern_wait6(), which is called by kern_wait(). Remove the redundand
check, introduced in r243136, and add a comment noting this, to make
the code less confusing.
The blank lines are added to properly delineate the scope of the
preceeding comments.
Noted by: "Jukka A. Ukkonen" <jau@iki.fi>
MFC after: 1 week
but use normal references instead of weak. This makes the statically
linked binaries to use fast gettimeofday(2) by forcing the linker to
resolve references and providing the neccessary functions.
Reported by: bde
Tested by: marius (sparc64)
MFC after: 2 weeks
timecounter to 1, and correspondingly increase the precision of the
gettimeofday(2) and related functions in the default configuration.
The motivation for the TSC-low timecounter, as described in the
r222866, seems to provide a workaround for the non-serializing
behaviour of the RDTSC on some Intel hardware. Tests demonstrate that
even with the pre-shift of 8, the cross-core non-monotonicity of the
RDTSC is still observed reliably, e.g. on the Nehalems. The r238755
and r238973 implemented the proper fix for the issue.
The pre-shift of 1 is applied to keep TSC not overflowing for the
frequency of hardclock down to 2 sec/intr. The pre-shift is made a
tunable to allow the easy debugging of the issues users could see with
the shift being too low.
Reviewed by: bde
MFC after: 2 weeks
