In order to become independent of Coherency Fabric frequency, configure
Timer and Watchdog to operate in 25MHz mode.
Submitted by: Zbigniew Bodek <zbb@semihalf.com>
Copy the given range of mappings from the source map to the
destination map, thereby reducing the number of VM faults on fork.
Submitted by: Zbigniew Bodek <zbb@semihalf.com>
Sponsored by: The FreeBSD Foundation, Semihalf
* Grab the reset lock first, so any subsequent interrupt, TX, RX work
will fail
* Then shut down interrupts
* Then wait for TX/RX to finish running
At this point no further work will be running, so it's safe to do the
reset path code.
PR: kern/179232
The main problem here is that fast and driver RX diversity isn't actually
configured; I need to figure out why that is. That said, this makes
the single-antenna connected AR9285 and AR2427 (AR9285 w/ no 11n) work
correctly.
PR: kern/179269
Uncover some, previously reserved, fields that are used by Ext4.
These are currently unused but it is good to have them for future
reference.
Reviewed by: bde
MFC after: 3 days
of a lock within a single thread.
- Fix handling of interlocks in WITNESS by properly requiring the interlock
to be held exactly once if it is specified.
the vnode lock while iterating over the free vnode list. Instead of
yielding, pause for 1 tick. The change is reported to help in some
virtualized environments.
Submitted by: Roger Pau Monn? <roger.pau@citrix.com>
Discussed with: jilles
Tested by: pho
MFC after: 2 weeks
Xen host side can handle after defragmentation.
This prevents the driver from throwing away too long TSO chains and
improves the performance on Amazon AWS instances with 10GigE virtual
interfaces to the normally expected throughput.
Submitted by: cperciva (earlier version)
Reviewed by: cperciva
Tested by: cperciva
MFC after: 1 week
limited in the amount of data they can handle at once.
Drivers can set ifp->if_hw_tsomax before calling ether_ifattach() to
change the limit.
The lowest allowable size is IP_MAXPACKET / 8 (8192 bytes) as anything
less wouldn't be very useful anymore. The upper limit is still at
IP_MAXPACKET (65536 bytes). Raising it requires further auditing of
the IPv4/v6 code path's as the length field in the IP header would
overflow leading to confusion in firewalls and others packet handler on
the real size of the packet.
The placement into "struct ifnet" is a bit hackish but the best place
that was found. When the stack/driver boundary is updated it should
be handled in a better way.
Submitted by: cperciva (earlier version)
Reviewed by: cperciva
Tested by: cperciva
MFC after: 1 week (using spare struct members to preserve ABI)
cacos, cacosf, cacosh, cacoshf,
casin, casinf, casinh, casinhf,
catan, catanf, catanh, catanhf,
logl, log2l, log10l, log1pl
I am hoping kargl@ will commit expl and expm1l soon, in which case this
bump will cover those, too.
Requested by: danfe
space, fork(2) would cause shadowing of the physical object and
copying of the shared page into private copy, effectively preventing
updates for the exported timehands structure and stopping the clock.
Specify the maximum allowed permissions for the page to be read and
execute, preventing write from the user mode.
Reported and tested by: <huanghwh@yahoo.com>
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
used as the estimation of size, to 32GB. This provides around 100K of
buffer headers and corresponding KVA for buffer map at the peak.
Sizing the cache larger is not useful, also resulting in the wasting
and exhausting of KVA for large machines.
Reported and tested by: bdrewery
Sponsored by: The FreeBSD Foundation
clearing the page's PGA_REFERENCED flag. Since we are typically
manipulating the page's act_count field when we are clearing its
PGA_REFERENCED flag, the page lock is already held everywhere that we clear
the PGA_REFERENCED flag. So, in fact, this revision only changes some
comments and an assertion. Nonetheless, it will enable later changes to
object locking in the pageout code.
Introduce vm_page_assert_locked(), which completely hides the implementation
details of the page lock from the caller, and use it in
vm_page_aflag_clear(). (The existing vm_page_lock_assert() could not be
used in vm_page_aflag_clear().) Over the coming weeks, I expect that we'll
either eliminate or replace the various uses of vm_page_lock_assert() with
vm_page_assert_locked().
Reviewed by: attilio
Sponsored by: EMC / Isilon Storage Division
dtrace_probe(). Arguments beyond these five must be obtained in an
architecture-specific way; this can be done through the getargval provider
method, and through dtrace_getarg() if getargval isn't overridden.
This change fixes two off-by-one bugs in the way these arguments are fetched
in FreeBSD's DTrace implementation. First, the SDT provider must set the
aframes parameter to 1 when creating a probe. The aframes parameter controls
the number of frames that dtrace_getarg() will step over in order to find
the frame containing the extra arguments. On FreeBSD, dtrace_getarg() is
called in SDT probe context via
dtrace_probe()->dtrace_dif_emulate()->dtrace_dif_variable->dtrace_getarg()
so aframes must be 3 since the arguments are in dtrace_probe()'s frame; it
was previously being called with a value of 2 instead. illumos uses a
different aframes value for SDT probes, but this is because illumos SDT
probes fire by triggering the #UD fault handler rather than calling
dtrace_probe() directly.
The second bug has to do with the way arguments are grabbed out
dtrace_probe()'s frame on amd64. The code currently jumps over the first
stack argument and retrieves the rest of them using a pointer into the
stack. This works on i386 because all of dtrace_probe()'s arguments will be
on the stack and the first argument is the probe ID, which should be
ignored. However, it is incorrect to ignore the first stack argument on
amd64, so we correct the pointer used to access the arguments.
MFC after: 2 weeks
seven arguments.
The original test uses Solaris' uadmin system call to trigger the test
probe; this change adds a sysctl to the dtrace_test module and gets the test
program to trigger the test probe via the sysctl handler.
The test is currently failing on amd64 because of some bugs in the way that
probe arguments beyond the first five are obtained - these bugs will be
fixed in a separate change.
lock instead of the object lock, there is no reason for vm_page_activate()
to assert that the object is locked for either read or write access.
(The "VPO_UNMANAGED" flag never changes after page allocation.)
Sponsored by: EMC / Isilon Storage Division
requires a pkthdr being present but that's not the case for either
_bus_dmamap_load_mbuf_sg() or bus_dmamap_load_mbuf_sg(9).
Reported by: sbruno
MFC after: 1 week
Remove local, and incorrect, definition for the value of an invalid
grant reference.
Extract ring cleanup code into xbd_free_ring() function for
symetry with xbd_alloc_ring(). This process also eliminated
an initialized but unused variable.
Sponsored by: Spectra Logic Corporation
MFC after: 1 week
o Group functions by by their functionality.
o Remove superfluous declarations.
o Remove more unused (#ifdef'd out) code.
Sponsored by: Spectra Logic Corporation
o This driver is the "xbd" driver, not the "blkfront", "blkif", "xbf", or
"xb" driver. Use the "xbd_" naming conventions for all functions,
structures, and constants.
o The prevailing convention for structure fields in this driver is to
prefix them with an abreviation of the structure type. Update
"recently added" fields to match this style.
o Remove unused data structures.
o Remove superfluous casts.
o Make a pass over the whole driver and bring it closer to
style(9) conformance.
Sponsored by: Spectra Logic Corporation
MFC after: 1 week
reason to inline the implementation of vm_page_lock_assert() in the
!KLD_MODULES case. Use the same implementation for both KLD_MODULES and
!KLD_MODULES.
Reviewed by: kib
- Use a shared bufobj lock in getblk() and inmem().
- Convert softdep's lk to rwlock to match the bufobj lock.
- Move INFREECNT to b_flags and protect it with the buf lock.
- Remove unnecessary locking around bremfree() and BKGRDINPROG.
Sponsored by: EMC / Isilon Storage Division
Discussed with: mckusick, kib, mdf
they are needed when porting some of the Solaris providers (ip, iscsi, and
tcp in particular).
dtrace_probe() only takes five arguments from the probe site, so we need to
add the appropriate cast to allow for more than five arguments. The extra
arguments are later copied out of dtrace_probe()'s stack frame by
dtrace_getarg() (or the provider-specific getarg method) as needed.
MFC after: 1 week
Actually, this may be further optimized for controller variants
supporting one-shot MSIs but I'm lacking the necessary hardware for
testing.
- Add some missing synchronization of the statistics and status DMA
maps.
MFC after: 1 week
change. Retest the ref_count and return from the function to not
execute the further code which assumes that ref_count == 1 if it is
not. Also, do not leak vnode lock if other thread cleared OBJ_TMPFS
flag meantime.
Reported by: bdrewery
Tested by: bdrewery, pho
Sponsored by: The FreeBSD Foundation
altered or actually needed there any longer.
- Honor errors passed to the DMA mapping callbacks.
- In bce_get_rx_buf(), do not reserve stack space for more DMA segments
than actually necessary.
- In bce_get_pg_buf(), take advantage of bus_dmamap_load_mbuf_sg(9).
- In bce_rx_intr(), remove a pointless check for an empty mbuf pointer
which can only happen in case of a severe programming error. Moreover,
recovering from that situation would require way more actions with header
splitting enabled (which it is by default).
- Fix VLAN tagging in the RX path; do not attach the VLAN tag twice if the
firmware has been told to keep it. [1]
Obtained from: OpenBSD [1]
MFC after: 1 week
patching at runtime actually const.
- Remove pointless softc members by employing the corresponding constants
directly.
- Remove pointless returns.
- Remove unnecessary inclusion of opt_device_polling.h.
- Replace an outdated and now bogus comment in bce_tick() with the
appropriate one.
MFC after: 1 week
- the VALE switch now support up to 254 destinations per switch,
unicast or broadcast (multicast goes to all ports).
- we can attach hw interfaces and the host stack to a VALE switch,
which means we will be able to use it more or less as a native bridge
(minor tweaks still necessary).
A 'vale-ctl' program is supplied in tools/tools/netmap
to attach/detach ports the switch, and list current configuration.
- the lookup function in the VALE switch can be reassigned to
something else, similar to the pf hooks. This will enable
attaching the firewall, or other processing functions (e.g. in-kernel
openvswitch) directly on the netmap port.
The internal API used by device drivers does not change.
Userspace applications should be recompiled because we
bump NETMAP_API as we now use some fields in the struct nmreq
that were previously ignored -- otherwise, data structures
are the same.
Manpages will be committed separately.
the actual PCI device which makes the request for DMA tag, instead of
some descendant of the PCI device, by creating a pass-through trampoline.
- Sprinkle const on tables.
- Use NULL instead of 0 for pointers.
- Take advantage of nitems().
MFC after: 1 week
Intel and Sharp flash power on with their blocks in a "locked" state.
Unlocked them before attempting to perform an erase or write action and
relock when the action is complete.
this file is in FreeBSD. There's formality to this that hasn't
happened and Juniper is perfectly fine with being the holder.
Discussed with: eadler, imp, jhb
truncated directory for some NFS servers. This turned out to
be because the size of a directory reported by an NFS server
can be smaller that the ufs-like directory created from the
RPC XDR in the client. This patch fixes the problem by changing
r248567 so that vnode_pager_setsize() is only done for regular files.
Reported and tested by: hartmut.brandt@dlr.de
Reviewed by: kib
MFC after: 1 week
It can now be accessed with a write lock on the object containing it OR
with a read lock on the object containing it along with the swhash_mtx.
o Remove some duplicate assertions for swap_pager_freespace() and
swap_pager_unswapped() but keep the object locking references for
documentation.
Sponsored by: EMC / Isilon storage division
Reviewed by: alc
Re-ordered SSD quirks alphabetically so they are easier to maintain.
Removed my email and PR reference from comments on each quirk.
Added quirks for more SSDs:
* Crucial M4
* Corsair Force GT
* Intel 520 Series
* Kingston E100 Series
* Samsung 830 Series
Reviewed by: pjd (mentor)
Approved by: pjd (mentor)
MFC after: 1 week
check_deferred_signal() returns twice, since handle_signal() emulates
the return from the normal signal handler by sigreturn(2)ing the
passed context. Second return is performed on the destroyed stack
frame, because __fillcontextx() has already returned. This causes
undefined and bad behaviour, usually the victim thread gets SIGSEGV.
Avoid nested frame and the need to return from it by doing direct call
to getcontext() in the check_deferred_signal() and using a new private
libc helper __fillcontextx2() to complement the context with the
extended CPU state if the deferred signal is still present.
The __fillcontextx() is now unused, but is kept to allow older
libthr.so to be used with the new libc.
Mark __fillcontextx() as returning twice [1].
Reported by: pgj
Pointy hat to: kib
Discussed with: dim
Tested by: pgj, dim
Suggested by: jilles [1]
MFC after: 1 week
value on purpose, but the ia32 context handling code is logically more
correct to use the _MC_IA32_HASFPXSTATE name for the flag.
Tested by: dim, pgj
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
usermode context state is not changed by the get operation, and
get_mcontext() does not require full iret as well.
Tested by: dim, pgj
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
context on return from the trap handler, re-enable the interrupts on
i386 and amd64. The trap return path have to disable interrupts since
the sequence of loading the machine state is not atomic. The trap()
function which transfers the control to the special handler would
enable the interrupt, but an iret loads the previous eflags with PSL_I
clear. Then, the special handler calls trap() on its own, which now
sees the original eflags with PSL_I set and does not enable
interrupts.
The end result is that signal delivery and process exiting code could
be executed with interrupts disabled, which is generally wrong and
triggers several assertions.
For amd64, the interrupts are enabled conditionally based on PSL_I in
the eflags of the outer frame, as it is already done for
doreti_iret_fault. For i386, the interrupts are enabled
unconditionally, the ast loop could have opened a window with
interrupts enabled just before the iret anyway.
Reported and tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
controller hardware most likely present on UHCI chipsets aswell. The
bug manifests itself when issuing isochronous transfers and bulk
transfers towards the same device simultaneously. From time to time it
happens that either the completion IRQ was missing or that the
completion IRQ was happening before the ITD/SITD was completely
written back to memory. The workaround assumes that double buffered
isochronous transfers are used, and that a second interrupt is
generated at the beginning of the next isochronous transfer to
complete the previous one. Possibly skipping the interrupt at the last
isochronous frame is possible, but will then break single buffered
isochronous transfers. For now we can live with some extra interrupts.
MFC after: 1 week
and if queue mechanism; also fix up (non-11n) TX fragment handling.
This may result in a bit of a performance drop for now but I plan on
debugging and resolving this at a later stage.
Whilst here, fix the transmit path so fragment transmission works.
The TX fragmentation handling is a bit more special. In order to
correctly transmit TX fragments, there's a bunch of corner cases that
need to be handled:
* They must be transmitted back to back, in the same order..
* .. ie, you need to hold the TX lock whilst transmitting this
set of fragments rather than interleaving it with other MSDUs
destined to other nodes;
* The length of the next fragment is required when transmitting, in
order to correctly set the NAV field in the current frame to the
length of the next frame; which requires ..
* .. that we know the transmit duration of the next frame, which ..
* .. requires us to set the rate of all fragments to the same length,
or make the decision up-front, etc.
To facilitate this, I've added a new ath_buf field to describe the
length of the next fragment. This avoids having to keep the mbuf
chain together. This used to work before my 11n TX path work because
the ath_tx_start() routine would be handed a single mbuf with m_nextpkt
pointing to the next frame, and that would be maintained all the way
up to when the duration calculation was done. This doesn't hold
true any longer - the actual queuing may occur at any point in the
future (think ath_node TID software queuing) so this information
needs to be maintained.
Right now this does work for non-11n frames but it doesn't at all
enforce the same rate control decision for all frames in the fragment.
I plan on fixing this in a followup commit.
RTS/CTS has the same issue, I'll look at fixing this in a subsequent
commit.
Finaly, 11n fragment support requires the driver to have fully
decided what the rate scenario setup is - including 20/40MHz,
short/long GI, STBC, LDPC, number of streams, etc. Right now that
decision is (currently) made _after_ the NAV field value is updated.
I'll fix all of this in subsequent commits.
Tested:
* AR5416, STA, transmitting 11abg fragments
* AR5416, STA, 11n fragments work but the NAV field is incorrect for
the reasons above.
TODO:
* It would be nice to be able to queue mbufs per-node and per-TID so
we can only queue ath_buf entries when it's time to assemble frames
to send to the hardware.
But honestly, we should just do that level of software queue management
in net80211 rather than ath(4), so I'm going to leave this alone for now.
* More thorough AP, mesh and adhoc testing.
* Ensure that net80211 doesn't hand us fragmented frames when A-MPDU has
been negotiated, as we can't do software retransmission of fragments.
* .. set CLRDMASK when transmitting fragments, just to ensure.
__amd64__, and thus limited. Eliminate 2 trivial conditionals by
casting the 64-bit integral, holding an address, via (uintptr_t)
to (void *) and replace the last remaining check for __amd64__
with a check for __LP64__ instead.
It turns out that in C++11, char16_t and char32_t are built-in types;
language keywords. Just fix this by putting traditional _*_T_DECLARED
blocks around the definitions. We'll just predefine these in
<sys/_types.h>.
This also opens up the possibility to define char16_t in other header
files, if ever needed (e.g. if we would gain a <ctype.h> for
char16_t/char32_t).
When creating fragment frames, the header length should honour the
DATAPAD flag.
This fixes the fragments that are queued to the ath(4) driver but it
doesn't yet fix fragment transmission. That requires further changes
to the ath(4) transmit path. Well, strictly speaking, it requires
further changes to _all_ wifi driver transmit paths, but this is at least
a start.
Tested:
* AR5416, STA mode, w/ fragthreshold set to 256.
This prevents users from selecting a delete method which may cause
corruption e.g. MPS WS16 on pre P14 firmware.
Reviewed by: pjd (mentor)
Approved by: pjd (mentor)
MFC after: 2 days
Assign the rv variable a success code if the pager was not asked for
the page. Using an error code from the previous processed page caused
zeroing of the valid page, when e.g. the previous page was not
available in the pager.
Reported by: lstewart
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
USDT probes exits. This was previously done with a callout; however, it is
possible to sleep while holding the DTrace mutexes, so a panic will occur
on INVARIANTS kernels if the callout handler can't immediately acquire one
of these mutexes. This panic will be frequently triggered on systems where
a USDT-enabled program (perl, for instance) is often run.
This revision changes the fasttrap cleanup mechanism so that a dedicated
thread is used instead of a callout. The old behaviour is otherwise
preserved.
Reviewed by: rpaulo
MFC after: 1 month
be a GOOD IDEA (TM).
Apparently MOST users set this (e.g. tcp and friends) but there are a few
users that just assume that it is a sensible value but then go on to read it.
These include SCTP, pf and the FLOWTABLE option (and maybe others).
avoid a dangling pointer and eventual panic on system shutdown.
Reported by: Ali <comnetboy at gmail.com>
Tested by: Ali <comnetboy at gmail.com>
MFC after: 1 week
ownership to the FreeBSD foundation for the years this file has been in
the FreeBSD repository.
This file was originally created by Juniper as part of upgrading to FreeBSD
4.10 (which had no MIPS support) and held functions found on other machines
It grew actual functionality over time. The functionaliy was copied from
other architectures and ported to MIPS on a as-needed basis.
Approved by: Mark Baushke (Juniper IP)
Approved by: Megan Sugiyama (Juniper legal)
Pointed out by: jmallett@
Requested by: core (jhb@)
pmap_enter_locked() implementation was very ambiguous and confusing.
Rearrange it so that each part of the mapping creation is separated.
Avoid walking through the redundant conditions.
Extract vector_page specific PTE setup from normal PTE setting.
Submitted by: Zbigniew Bodek <zbb@semihalf.com>
Sponsored by: The FreeBSD Foundation, Semihalf
Using PVF_MOD, PVF_REF and PVF_EXEC is redundant as we can get the proper
info from PTE bits.
When the mapping is marked as executable and has been referenced we assume
that it has been executed. Similarly, when the mapping is set to be writable
and is referenced, it must have been due to write access to it.
PVF_MOD and PVF_REF flags are kept just for pmap_clearbit() usage,
to pass the information on which bit should be cleared.
Submitted by: Zbigniew Bodek <zbb@semihalf.com>
Sponsored by: The FreeBSD Foundation, Semihalf
Use pmap_find_pv if needed instead of multiplying its code throughout
pmap-v6.
Avoid possible NULL pointer dereference in pmap_enter_locked()
When trying to get m->md.pv_memattr, make sure that m != NULL,
in particular that vector_page is set to be NULL.
Do not set PGA_REFERENCED flag in pmap_enter_pv().
On ARM any new page reference will result in either entering the new
mapping by calling pmap_enter, etc. or fixing-up the existing mapping in
pmap_fault_fixup().
Therefore we set PGA_REFERENCED flag in the earlier mentioned cases and
setting it later in pmap_enter_pv() is just waste of cycles.
Delete unused pm_pdir pointer from the pmap structure.
Rearrange brackets in the fault cause detection in trap.c
Place the brackets correctly in order to see course of the conditions
instantaneously.
Unify naming in pmap-v6.c and improve style
Use naming common for whole pmap and compatible with other pmaps,
improve style where possible:
pm -> pmap
pg -> m
opg -> om
*pt -> *ptep
*pte -> *ptep
*pde -> *pdep
Submitted by: Zbigniew Bodek <zbb@semihalf.com>
Sponsored by: The FreeBSD Foundation, Semihalf
bit in PTE.
Enable Access Flag in CPU control. With AF enabled each valid mapping
needs to have referenced bit in PTE set in order to be able to cache
it in the TLB.
AP[0] bit is to be used as reference flag.
All access permissions are encoded by AP[2:1] wherein AP[1] is in fact
"user enable" and AP[2](APX) is "write disable".
All mappings are always set to be valid. Reference emulation is performed
by setting/clearing reference flag in PTE.
md.pvh_attrs are no longer necessary however pv_flags are still being used
for now.
Marking vm_page as "dirty" or "referenced" is being performed on:
- page or flag fault servicing in pmap_fault_fixup(), basing on the fault
type
- vm_fault servicing in pmap_enter() according to the desired protections
and faulty access type
Redundant page marking has been removed as on ARM we know exactly when the
particular page is referenced or is going to be written.
Submitted by: Zbigniew Bodek <zbb@semihalf.com>
Sponsored by: The FreeBSD Foundation, Semihalf
xen/xenbus/xenbusb.c:
In xenbusb_probe_children(), do not modify the XenBus state of
devices for which we have no PV driver support. An emulated device
we do support may share this backend. Hide the node from XenBus
instead.
This prevents closing the vkbd device, which Qemu's emulated keyboard
device is using as the source for keyboard events.
Tested with qemu-xen-traditional, qemu-xen and qemu stubdomains, all
working as expected.
Submitted by: Roger Pau Monne <roger.pau@citrix.com>
Reviewed by: gibbs
MFC after: 1 week
dev/xen/netfront:
In netif_free(), properly stop the interface and drain any pending
timers prior to disconnecting from the backend device.
Remove all media and detach our interface object from the system
prior to deleting it.
PR: kern/176471
Submitted by: Roger Pau Monne <roger.pau@citrix.com>
Reviewed by: gibbs
MFC after: 1 week
from 1k to 20k The previous value was good 10 years ago, but not
anymore now.
More importantly, lots of good surprises:
polling is incredibly effective under virtualization, and not only
prevents livelock but also saves most of the VM exit overhead in
receive mode.
Using polling, a FreeBSD instance under qemu-kvm remains perfectly
responsive even when bombed with 10 Mpps over an emulated e1000,
and happily processes 1.7 Mpps through ipfw.
Note that some incompatibilities still remain: e.g. polling is not
(yet) compatible with netmap, and seems to freeze the guest when
kern.polling.idle_poll=1
MFC after: 3 days
an error. One could argue that returning a buffer even when it is
not valid is incorrect, but bread has always returned a buffer
valid or not.
Reviewed by: kib
MFC after: 2 weeks
the return value is NULL. Based on the returned flags, the
return value should never be inspected in the case where NULL
is returned, but it is good coding practice not to return a
pointer to freed memory.
Found by: Coverity Scan, CID 1006096
Reviewed by: kib
MFC after: 2 weeks
o Relax locking assertions for pmap_enter_object() and add them also
to architectures that currently don't have any
o Introduce VM_OBJECT_LOCK_DOWNGRADE() which is basically a downgrade
operation on the per-object rwlock
o Use all the mechanisms above to make vm_map_pmap_enter() to work
mostl of the times only with readlocks.
Sponsored by: EMC / Isilon storage division
Reviewed by: alc
The <uchar.h> header, part of C11, adds a small number of utility
functions for 16/32-bit "universal" characters, which may or may not be
UTF-16/32. As our wchar_t is already ISO 10646, simply add light-weight
wrappers around wcrtomb() and mbrtowc().
While there, also add (non-yet-standard) _l functions, similar to the
ones we already have for the other locale-dependent functions.
Reviewed by: theraven
traffic.
When transmitting non-aggregate traffic, we need to keep the hardware
busy whilst transmitting or small bursts in txdone/tx latency will
kill us.
This restores non-aggregate iperf performance, especially when doing
TDMA.
Tested:
* AR5416<->AR5416, TDMA
* AR5416 STA <-> AR9280 AP
of course.)
There's a few things that needed to happen:
* In case someone decides to set the beacon transmission rate to be
at an MCS rate, use the MCS-aware version of the duration calculation
to figure out how long the received beacon frame was.
* If TxOP enforcing is available on the hardware and we're doing TDMA,
enable it after a reset and set the TDMA guard interval to zero.
This seems to behave fine.
TODO:
* Although I haven't yet seen packet loss, the PHY errors that would be
triggered (specifically Transmit-Override-Receive) aren't enabled
by the 11n HAL. I'll have to do some work to enable these PHY errors
for debugging.
What broke:
* My recent changes to the TX queue handling has resulted in the driver
not keeping the hardware queue properly filled when doing non-aggregate
traffic. I have a patch to commit soon which fixes this situation
(albeit by reminding me about how my ath driver locking isn't working
out, sigh.)
So if you want to test this without updating to the next set of patches
that I commit, just bump the sysctl dev.ath.X.hwq_limit from 2 to 32.
Tested:
* AR5416 <-> AR5416, with ampdu disabled, HT40, 5GHz, MCS12+Short-GI.
I saw 30mbit/sec in both directions using a bidirectional UDP test.
the right type for the argument in syscalls.master. Also fix the
posix_fallocate(2) and posix_fadvise(2) compat32 syscalls on the
architectures which require padding of the 64bit argument.
Noted and reviewed by: jhb
Pointy hat to: kib
MFC after: 1 week
for the case when the nullfs vnode is not reclaimed. Otherwise, later
reclamation would not unlock the lower vnode.
Reported by: antoine
Tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
registers also on other CPUs, besides the CPU which happens to execute
the ddb. The debugging registers are stored in the pcpu area,
together with the command which is executed by the IPI stop handler
upon resume.
Reviewed by: jhb
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
a vm page, denoted either by an address of the struct vm_page, or, if
the '/p' modifier is specified, by a physical address of the
corresponding frame.
Reviewed by: jhb
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
1. Common headers for fdt.h and ofw_machdep.h under x86/include
with indirections under i386/include and amd64/include.
2. New modinfo for loader provided FDT blob.
3. Common x86_init_fdt() called from hammer_time() on amd64 and
init386() on i386.
4. Split-off FDT specific low-level console functions from FDT
bus methods for the uart(4) driver. The low-level console
logic has been moved to uart_cpu_fdt.c and is used for arm,
mips & powerpc only. The FDT bus methods are shared across
all architectures.
5. Add dev/fdt/fdt_x86.c to hold the fdt_fixup_table[] and the
fdt_pic_table[] arrays. Both are empty right now.
FDT addresses are I/O ports on x86. Since the core FDT code does
not handle different address spaces, adding support for both I/O
ports and memory addresses requires some thought and discussion.
It may be better to use a compile-time option that controls this.
Obtained from: Juniper Networks, Inc.
I added this block, knowing that lint does not support _Thread_local.
When linting, we could argue that we don't care about TLS (yet). It
seems, however, that external pieces of software also sometimes do a
-Dlint, regex the output and compile it again.
Reported by: swills
apply to most jails but do apply to vnet jails. This includes adding
a new sysctl "security.jail.vnet" to identify vnet jails.
PR: conf/149050
Submitted by: mdodd
MFC after: 3 days
Group onboard mic and headphone mic jack together. Creates association that
will switch between microphone inputs depending on the state of the headphone
jack being connected to a live mic.
Fixes onboard mic not working at all on T520.
Tested on T520, T420.
Suspect X220 needs this too, untested on.
MFC after: 1 month
The list-based DMA engine has the following behaviour:
* When the DMA engine is in the init state, you can write the first
descriptor address to the QCU TxDP register and it will work.
* Then when it hits the end of the list (ie, it either hits a NULL
link pointer, OR it hits a descriptor with VEOL set) the QCU
stops, and the TxDP points to the last descriptor that was transmitted.
* Then when you want to transmit a new frame, you can then either:
+ write the head of the new list into TxDP, or
+ you write the head of the new list into the link pointer of the
last completed descriptor (ie, where TxDP points), then kick
TxE to restart transmission on that QCU>
* The hardware then will re-read the descriptor to pick up the link
pointer and then jump to that.
Now, the quirks:
* If you write a TxDP when there's been no previous TxDP (ie, it's 0),
it works.
* If you write a TxDP in any other instance, the TxDP write may actually
fail. Thus, when you start transmission, it will re-read the last
transmitted descriptor to get the link pointer, NOT just start a new
transmission.
So the correct thing to do here is:
* ALWAYS use the holding descriptor (ie, the last transmitted descriptor
that we've kept safe) and use the link pointer in _THAT_ to transmit
the next frame.
* NEVER write to the TxDP after you've done the initial write.
* .. also, don't do this whilst you're also resetting the NIC.
With this in mind, the following patch does basically the above.
* Since this encapsulates Sam's issues with the QCU behaviour w/ TDMA,
kill the TDMA special case and replace it with the above.
* Add a new TXQ flag - PUTRUNNING - which indicates that we've started
DMA.
* Clear that flag when DMA has been shutdown.
* Ensure that we're not restarting DMA with PUTRUNNING enabled.
* Fix the link pointer logic during TXQ drain - we should always ensure
the link pointer does point to something if there's a list of frames.
Having it be NULL as an indication that DMA has finished or during
a reset causes trouble.
Now, given all of this, i want to nuke axq_link from orbit. There's now HAL
methods to get and set the link pointer of a descriptor, so what we
should do instead is to update the right link pointer.
* If there's a holding descriptor and an empty TXQ list, set the
link pointer of said holding descriptor to the new frame.
* If there's a non-empty TXQ list, set the link pointer of the
last descriptor in the list to the new frame.
* Nuke axq_link from orbit.
Note:
* The AR9380 doesn't need this. FIFO TX writes are atomic. As long as
we don't append to a list of frames that we've already passed to the
hardware, all of the above doesn't apply. The holding descriptor stuff
is still needed to ensure the hardware can re-read a completed
descriptor to move onto the next one, but we restart DMA by pushing in
a new FIFO entry into the TX QCU. That doesn't require any real
gymnastics.
Tested:
* AR5210, AR5211, AR5212, AR5416, AR9380 - STA mode.
Most likely some non-USB compliant devices will choke on it
sooner or later. Clear stall is strictly speaking not needed.
If the first MIDI command sent or transmitted is lost, this
is not a big problem for us.
MFC after: 1 week
Set a valid alternate interface setting
when enumerating USB audio devices else
the device mentioned will not work like
expected.
PR: usb/178722
MFC after: 1 week
o The CP2101 and CP2102 do not support GPIO pin use at all, enforce this.
o Support reading the GPIO status on the second port of the CP2105. More
work is needed before the CP2105 GPIO pins can be used as outputs.
Hardware donated by: Silicon Labs
MFC after: 3 weeks
tree is used to maintain the object's collection of resident pages,
vm_page_lookup() no longer needs an exclusive lock.
Reviewed by: attilio
Sponsored by: EMC / Isilon Storage Division
doesn't match the actual hardware queue this frame is queued to.
I'm trying to ensure that the holding buffers are actually being queued
to the same TX queue as the holding buffer that they end up on.
I'm pretty sure this is all correct so if this complains, it'll be due
to some kind of subtle broken-ness that needs fixing.
This is only done for legacy hardware, not EDMA hardware.
Tested:
* AR5416 STA mode, very lightly
PS-POLL support.
This implements PS-POLL awareness i nthe
* Implement frame "leaking", which allows for a software queue
to be scheduled even though it's asleep
* Track whether a frame has been leaked or not
* Leak out a single non-AMPDU frame when transmitting aggregates
* Queue BAR frames if the node is asleep
* Direct-dispatch the rest of control and management frames.
This allows for things like re-association to occur (which involves
sending probe req/resp as well as assoc request/response) when
the node is asleep and then tries reassociating.
* Limit how many frames can set in the software node queue whilst
the node is asleep. net80211 is already buffering frames for us
so this is mostly just paranoia.
* Add a PS-POLL method which leaks out a frame if there's something
in the software queue, else it calls net80211's ps-poll routine.
Since the ath PS-POLL routine marks the node as having a single frame
to leak, either a software queued frame would leak, OR the next queued
frame would leak. The next queued frame could be something from the
net80211 power save queue, OR it could be a NULL frame from net80211.
TODO:
* Don't transmit further BAR frames (eg via a timeout) if the node is
currently asleep. Otherwise we may end up exhausting management frames
due to the lots of queued BAR frames.
I may just undo this bit later on and direct-dispatch BAR frames
even if the node is asleep.
* It would be nice to burst out a single A-MPDU frame if both ends
support this. I may end adding a FreeBSD IE soon to negotiate
this power save behaviour.
* I should make STAs timeout of power save mode if they've been in power
save for more than a handful of seconds. This way cards that get
"stuck" in power save mode don't stay there for the "inactivity" timeout
in net80211.
* Move the queue depth check into the driver layer (ath_start / ath_transmit)
rather than doing it in the TX path.
* There could be some naughty corner cases with ps-poll leaking.
Specifically, if net80211 generates a NULL data frame whilst another
transmitter sends a normal data frame out net80211 output / transmit,
we need to ensure that the NULL data frame goes out first.
This is one of those things that should occur inside the VAP/ic TX lock.
Grr, more investigations to do..
Tested:
* STA: AR5416, AR9280
* AP: AR5416, AR9280, AR9160
QLogic 8300 Series Adapters
Submitted by: David C Somayajulu (davidcs@freebsd.org) QLogic Corporation
Approved by: George Neville-Neil (gnn@freebsd.org)
PV entries are now roughly half the size.
Instead of using a shared UMA zone for 28 byte pv entries
(two 8-byte tailq nodes, a 4 byte pointer, a 4 byte address and 4 byte
flags), we allocate a page at a time per process.
This provides 252 pv entries per process (actually, per pmap address space)
and eliminates one of the 8-byte tailq entries since we now can track
per-process pv entries implicitly.
The pointer to the pmap can be eliminated by doing address arithmetic to
find the metadata on the page headers to find a single pointer shared by
all 252 entries. There is an 8-int bitmap for the freelist of those 252
entries.
When in serious low memory condition, allocation of another pv_chunk is
possible by freeing some pages in pmap_pv_reclaim().
Added pv_entry/pv_chunk related statistics to pmap.
pv_entry/pv_chunk statistics can be accessed via sysctl vm.pmap.
Ported PTE freelist of KVA allocation and maintenance from i386.
Using an idea from Stephan Uphoff, use the empty pte's that correspond
to the unused kva in the pv memory block to thread a freelist through.
This allows us to free pages that used to be used for pv entry chunks
since we can now track holes in the kva memory block.
As both ARM pmap.c and pmap-v6.c use the same header and pv_entry, pmap and
md_page structures are different, it was needed to separate code designed
for ARMv6/7 from the one for other ARMs.
Submitted by: Zbigniew Bodek <zbb@semihalf.com>
Reviewed by: alc
Sponsored by: The FreeBSD Foundation, Semihalf
Instead of doing all sorts of weird casting of constants to
pointer-pointers, simply use the standard C offsetof() macro to obtain
the offset of the respective fields in the structures.
Instead of only checking the __STDC_VERSION__, we can also use Clang's
__has_extension() to check for features specifically. This allows us to,
say, use Clang's native _Static_assert() instead of the typedef hack,
making the compiler error messages a lot more readable.
Reviewed by: theraven
* Move the node sleep/wake state under the TX lock rather than the
node lock. Let's leave the node lock protecting rate control only
for now.
* When reassociating, various state needs to be cleared. For example,
the aggregate session needs to be torn down, including any pending
aggregation negotiation and BAR TX waiting.
* .. and we need to do a "cleanup" pass since frames in the hardware
TX queue need to be transmitted.
Modify ath_tx_tid_cleanup() to be called with the TX lock held and push
frames into a completion list. This allows for the cleanup to be
done atomically for all TIDs in a node rather than grabbing and
releasing the TX lock each time.
freelist.
o Split the pool of free pages queues really by domain and not rely on
definition of VM_RAW_NFREELIST.
o For MAXMEMDOM > 1, wrap the RR allocation logic into a specific
function that is called when calculating the allocation domain.
The RR counter is kept, currently, per-thread.
In the future it is expected that such function evolves in a real
policy decision referee, based on specific informations retrieved by
per-thread and per-vm_object attributes.
o Add the concept of "probed domains" under the form of vm_ndomains.
It is responsibility for every architecture willing to support multiple
memory domains to correctly probe vm_ndomains along with mem_affinity
segments attributes. Those two values are supposed to remain always
consistent.
Please also note that vm_ndomains and td_dom_rr_idx are both int
because segments already store domains as int. Ideally u_int would
have much more sense. Probabilly this should be cleaned up in the
future.
o Apply RR domain selection also to vm_phys_zero_pages_idle().
Sponsored by: EMC / Isilon storage division
Partly obtained from: jeff
Reviewed by: alc
Tested by: jeff
bit available for a flag in the pointer. However, it felt more correct
to enforce natural alignment of the key pointer. Unfortunately on
32bit architectures 64bit integers are not always naturally aligned.
Change the assert to enforce only 32bit alignment of the 64bit key for
now to fix the build. A more correct fix would be to properly sort
the struct buf fields which definitely suffer from bloat due to padding.
vm_page_insert() so that (1) vm_radix_lookup_le() is never called while the
free page queues lock is held and (2) vm_radix_lookup_le() is called at most
once. This change reduces the average time that the free page queues lock
is held by vm_page_alloc() as well as vm_page_alloc()'s average overall
running time.
Sponsored by: EMC / Isilon Storage Division
users to guarantee that the output of DTrace scripts will be time-ordered.
This option is enabled by adding the line
#pragma D option temporal
to the beginning of a script, or by adding '-x temporal' to the arguments of
dtrace(1).
This change fixes a bug in the original port of the temporal option. This
bug was causing some assertions to fail, so they had been disabled; in this
revision the assertions are working properly and are enabled.
The DTrace version number has been bumped from 1.9.0 to 1.9.1 to reflect
the language change that's being introduced.
This change corresponds to part of illumos-gate commit e5803b76927480:
3021 option for time-ordered output from dtrace(1M)
Reviewed by: pfg
Obtained from: illumos
MFC after: 1 month
with any structure containing a uint64_t index. The tree code
auto-generates type safe wrappers.
- Eliminate the buf splay and replace it with pctrie. This is not only
significantly faster with large files but also allows for the possibility
of shared locking.
Reviewed by: alc, attilio
Sponsored by: EMC / Isilon Storage Division
EABI ARM kernels or clang-compiled ARM kernels.
This fixes a crash seen in clang-compiled ARM
kernels that include WITNESS.
This code could be easily modified to walk the stack
for current clang-generated code (including EABI)
but Andrew Turner has raised concerns that the
stack frame currently emitted by clang isn't actually
required by EABI so such a change might cause problems
down the road.
In case anyone wants to experiment, the change
to support current clang-compiled kernels
involves simply setting FR_RFP=0 and FR_SCP=1.
functions, reverse the numbering scheme for the levels. The highest
numbered level in the tree now appears near the root instead of the leaves.
Sponsored by: EMC / Isilon Storage Division
With "cached read" HDD testing and multiple ports busy on a SATA
host controller, 3726/3826 PMP will very rarely drop a deferred
R_OK that was intended for the host. Symptom will be all 5 drives
under test will timeout, get reset, and recover.
Submitted by: Rich Futyma <rich.futyma@sanmina.com>
MFC after: 2 weeks
null_hashget() obtains the reference on the nullfs vnode, which must
be dropped.
- Fix a wart which existed from the introduction of the nullfs
caching, do not unlock lower vnode in the nullfs_reclaim_lowervp().
It should be innocent, but now it is also formally safe. Inform the
nullfs_reclaim() about this using the NULLV_NOUNLOCK flag set on
nullfs inode.
- Add a callback to the upper filesystems for the lower vnode
unlinking. When inactivating a nullfs vnode, check if the lower
vnode was unlinked, indicated by nullfs flag NULLV_DROP or VV_NOSYNC
on the lower vnode, and reclaim upper vnode if so. This allows
nullfs to purge cached vnodes for the unlinked lower vnode, avoiding
excessive caching.
Reported by: G??ran L??wkrantz <goran.lowkrantz@ismobile.com>
Tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
