The reference HAL pushes a config group parameter to the driver layer
to inform it which particular chip behaviour to implement.
This particular value tags it as an AR9285.
The AR9485 chip and AR933x SoC both implement LNA diversity.
There are a few extra things that need to happen before this can be
flipped on for those chips (mostly to do with setting up the different
bias values and LNA1/LNA2 RSSI differences) but the first stage is
putting this code into the driver layer so it can be reused.
This has the added benefit of making it easier to expose configuration
options and diagnostic information via the ioctl API. That's not yet
being done but it sure would be nice to do so.
Tested:
* AR9285, with LNA diversity enabled
* AR9285, with LNA diversity disabled in EEPROM
SPC-4 specification states that serial number may be property of device,
but not a specific logical unit. People reported about FC storages using
serial number in that way, making it unusable for purposes of LUN multipath
detection. SPC-4 states that designators associated with logical unit from
the VPD page 83h "Device Identification" should be used for that purpose.
Report first of them in the new attribute in such preference order: NAA,
EUI-64, T10 and SCSI name string.
While there, make GEOM DISK properly report GEOM::ident in XML output also
using d_getattr() method, if available. This fixes serial numbers reporting
for SCSI disks in `geom disk list` output and confxml.
Discussed with: gibbs, ken
Sponsored by: iXsystems, Inc.
MFC after: 2 weeks
d_getattr(). Since these drivers use disk(9) KPI and not directly GEOM, use
of that function means KPI layering violation, causing extra g_io_deliver()
call for the request.
While GEOM in general has provider opened while sending BIO_GETATTR,
GEOM DISK does not really need to open disk to read medium-unrelated
attributes for own use.
Proposed by: ken
ZFS event processing should work on R/O root filesystems
Illumos ZFS issues:
3749 zfs event processing should work on R/O root filesystems
MFC after: 2 weeks
linux_file structure and use it instead of directly accessing td_fpop
when destroying the linux_file structure. The td_fpop pointer is not
valid when a cdevpriv destructor is run, and the type-specific close
method has already been called, so f_vnode may not be valid (and the
vnode might have been recycled without our own reference).
Tested by: Julian Stecklina <jsteckli@os.inf.tu-dresden.de>
MFC after: 1 week
running state. fxp(4) requires controller reinitialization for the
following cases.
o RX lockup condition on i82557
o promiscuous mode change
o multicast filter change
o WOL configuration
o TSO/VLAN hardware tagging/checksum offloading configuration
o MAC reprogramming after speed/duplex/flow-control resolution
o Any events that result in MAC reprogramming(link UP/DOWN,
remote link partner's restart of auto-negotiation etc)
o Microcode loading/unloading
Apart from above cases which come from hardware limitation, upper
stack also blindly reinitializes controller whenever an IP address
is assigned. After r194573, fxp(4) no longer needs to reinitialize
the controller to program multicast filter after upping the
interface. So keeping track of driver running state should remove
all unnecessary controller reinitializations.
This change will also address endless controller reinitialization
triggered by dhclient(8).
Tested by: hrs, Alban Hertroys <haramrae@gmail.com>
about mount and unmount events. This is used by Juniper to implement a more
optimal implementation of NetBSD's veriexec.
Submitted by: stevek@juniper.net
Obtained from: Juniper Networks, Inc
when booting from ZFS turned out to also cause the boot path not being
adjusted if booting from CD-ROM with firmware versions that do not employ
the "cdrom" alias in that case. So shuffle the code around instead in order
to achieve the original intent. Ideally, we shouldn't fiddle with the boot
path when booting from UFS on a disk either; unfortunately, there doesn't
seem to be an universal way of telling disks and CD-ROMs apart, though. [1]
- Use NULL instead of 0 for pointers.
PR: 179289
MFC after: 1 week
This allows setting attributes on tables. One simply does not provide
an index in that case. Otherwise the entry corresponding the index has
the attribute set or unset.
Use this change to fix a relatively longstanding bug in our GPT scheme
that's the result of rev 198097 (relatively harmless) followed by rev
237057 (damaging). The damaging part being that our GPT scheme always
has the active flag set on the PMBR slice. This is in violation with
EFI. Existing EFI implementions for both x86 and ia64 reject the GPT.
As such, GPT disks created by us aren't usable under EFI because of
that.
After this change, GPT disks never have the active flag set on the PMBR
slice. In order to make the GPT disk bootable under some x86 BIOSes,
the reason of rev 198097, one must now set the active attribute on the
gpt table. The kernel will apply this to the PMBR slice For (S)ATA:
gpart set -a active ada0
To fix an existing GPT disk that has the active flag set in the PMBR,
and that does not need the flag, use (again for (S)ATA):
gpart unset -a active ada0
The EBR, MBR & PC98 schemes, which also impement at least 1 attribute,
now check to make sure the entry passed is valid. They do not have
attributes that apply to the table.
The superblock in ext2fs defines all the fields as unsigned but for
some reason the in-memory superblock was carrying e2fs_bpg and
e2fs_isize as signed.
We should preserve the specified types for consistency.
MFC after: 5 days
After pushing in my fix for the 2 byte functions, I realized that the
functions for 1 and 2 byte operations had become identical. Reduce the
code size by merging the functions for 1 and 2 byte operations together.
While there, slightly improve variable naming and comments.
This is based on the AR933x (Hornet) SoC from Qualcomm Atheros.
It's a much nicer board to do development on - 64MB RAM, 16MB flash.
The development board breaks out the GPIO pins, ethernet, serial (via
a USB<->RS232 chip), USB host and of course a small wifi antenna.
Everything but the wifi works thus far.
Even though I tested the 1-byte operations on arbitrarily aligned bytes,
it seems I did not do this for the 2-byte operations.
Create easy to read functions that are used to get/put bytes and
halfwords in words. To keep the compiler happy, explicitly read two
bytes into a union to obtain a 16-bit value.
Realtek RTL8188CU/RTL8192CU USB IEEE 802.11b/g/n wireless cards.
This driver requires microcode which is available in FreeBSD ports:
net/urtwn-firmware-kmod.
Hiren ported the urtwn(4) man page from OpenBSD and Glen just commited a port
for the firmware.
TODO:
- 802.11n support
- Stability fixes - the driver can sustain lots of traffic but has trouble
coping with simultaneous iperf sessions.
- fix debugging
MFC after: 2 months
Tested by: kevlo, hiren, gjb
To make <stdatomic.h> work on MIPS (and ARM) using GCC, we need to
provide implementations of the __sync_*() functions. I already added
these functions for 4 and 8 byte types to libcompiler-rt some time ago,
based on top of <machine/atomic.h>.
Unfortunately, <machine/atomic.h> only provides a subset of the features
needed to implement <stdatomic.h>. This means that in some cases we had
to do compare-and-exchange calls in loops, where a simple ll/sc would
suffice.
Also implement these functions for 1 and 2 byte types. MIPS only
provides ll/sc instructions for 4 and 8 byte types, but this is of
course no limitation. We can simply load 4 bytes and use some bitmask
tricks to modify only the bytes affected.
Discussed on: mips, arch
Tested with: QEMU
* Illumos ZFS issue #3805 arc shouldn't cache freed blocks
Quote from the Illumos issue:
ZFS should proactively evict freed blocks from the cache.
Even though these freed blocks will never be used again, and thus
will eventually be evicted, this causes us to use memory
inefficiently for 2 reasons:
1. A block that is freed has no chance of being accessed again, but
will be kept in memory preferentially to a block that was accessed
before it (and is thus older) but has not been freed and thus has
at least some chance of being accessed again.
2. We partition the ARC into several buckets:
user data that has been accessed only once (MRU)
metadata that has been accessed only once (MRU)
user data that has been accessed more than once (MFU)
metadata that has been accessed more than once (MFU)
The user data vs metadata split is somewhat arbitrary, and the
primary control on how much memory is used to cache data vs metadata
is to simply try to keep the proportion the same as it has been in the
past (each bucket "evicts against" itself). The secondary control is
to evict data before evicting metadata.
Because of this bucketing, we may end up with one bucket mostly
containing freed blocks that are very old, while another bucket has
more recently accessed, still-allocated blocks. Data in the useful
bucket (with still-allocated blocks) may be evicted in preference to
data in the useless bucket (with old, freed blocks).
On dcenter, we saw that the MFU metadata bucket was 230MB, while the
MFU data bucket was 27GB and the MRU metadata bucket was 256GB.
However, the vast majority of data in the MRU metadata bucket (256GB)
was freed blocks, and thus useless. Meanwhile, the MFU metadata bucket
(230MB) was constantly evicting useful blocks that will be soon needed.
The problem of cache segmentation is a larger problem that needs more
investigation. However, if we stop caching freed blocks, it should
reduce the impact of this more fundamental issue.
MFC after: 2 weeks
1) Only multi-TD isochronous transfers should use NORMAL
type after specific type as per XHCI specification.
2) BEI bit is only available in NORMAL and ISOCHRONOUS
TRB types. Don't use this bit for other types to avoid
hardware asserts. Reserved bits should be don't care
though ...
MFC after: 1 week
PR: usb/179342
* Stop pretending we support anything other than ELF by removing code
surrounded by #ifdef __ELF__ ... #endif.
* Remove _JB_MAGIC_SETJMP and _JB_MAGIC__SETJMP, they are defined in
setjmp.h, which is able to be included from asm.
* Fix the spelling of dependent.
* Rename END _END and add END and ASEND to complement ENTRY and ASENTRY
respectively
* Add macros to simplify accessing the Global Offset Table, some of these
will be used in the upcoming update to the setjmp functions.
the regular interrupt handler is not working properly or
in case of MSI interrupts which are not yet supported.
Remove interrupt setup code for FreeBSD versions older
than 700031.
MFC after: 1 week
PR: usb/179342