Commit Graph

20 Commits

Author SHA1 Message Date
Ian Lepore
adcea15135 Don't iterate through the bits of the pending interrupt register if the
whole register is zero.  Most of the registers will be zero most of the time.
2013-10-31 03:12:48 +00:00
Ian Lepore
54fe60971c Reset the timer interrupt status register at the top rather than bottom of
the interrupt handler.  If the event callback starts a new short timeout,
the timer can fire before returning from the event callback, and clearing
the interrupt status after that loses the interrupt and hangs until the
counter wraps.  Fixing all of this removes the need for the do-nothing
loop at the top of the handler which really just waited for the counter to
roll over and reach the one-shot count again.

Also add a missing return(0) in the periodic timer start case.
2013-10-31 02:11:35 +00:00
Ian Lepore
eb756ebd94 Expand the list of compatible devices this driver works with. Increase
the target frequency from 1 to 10 MHz because these SoCs are plenty fast
enough to benefit from the extra event timer resolution.
2013-10-31 01:45:55 +00:00
Ian Lepore
bc9a95c8c6 Add a "no-op" USB PHY driver for imx-family SoCs. This is used when the
phy clocks need to be enabled, but no other hardware setup is needed to
make the phy work.
2013-10-30 14:38:24 +00:00
Ian Lepore
baf7f63f9a Add some bare-bones support for enabling usb and usbphy clocks. This
is temporary code to keep imx development moving forward for now.  In
the long run we need a SoC-independant clock management API.
2013-10-30 14:33:15 +00:00
Ian Lepore
6489412064 Remove #include <machine/frame.h> from all the arm code that doesn't
really need it.  That would be almost everywhere it was included.  Add
it in a couple files that really do need it and were previously getting
it by accident via another header.
2013-10-27 01:34:10 +00:00
Ian Lepore
69d75558a7 Remove all #include <machine/pmap.h> from arm code. It's already
included by vm/pmap.h, which is a prerequisite for arm/machine/pmap.h
so there's no reason to ever include it directly.

Thanks to alc@ for pointing this out.
2013-10-27 00:51:46 +00:00
Ian Lepore
ec4081c10a Maximize available kva space by doing static device mapping from the top
of the address space downwards, and then returning the lowest mapped
device address from initarm_lastaddr().  This adds over 500MB of kva
space compared to the old way of hardcoding the end address as 0xE0000000.

Also, pre-map most of the SoC's common memory-mapped devices using 1MB
section mappings so that all device access uses just a few TLB entries.
Graphics devices aren't mapped this way yet, but probably should be.

To provide this new functionality without pasting identical code into
multiple imxNN_machdep.c files, rework the imx machdep code so that
things common to the whole family of SoCs are in a new imx_machdep.c file.
The rewritten imxNN_machdep.c files contain just things specific to an
individual SoC.
2013-10-26 23:13:20 +00:00
Ian Lepore
dc82313758 Add a driver for the Freescale Fast Ethernet Controller found on various
Freescale SoCs including the i.MX series.  This also works for the newer
SoCs with the ENET gigabit controller, but doesn't use any of the new
hardware features other than enabling gigabit speed.
2013-10-20 21:07:38 +00:00
Ian Lepore
62e8bfb82a Switch to using the standard uart console driver instead of the special
driver for early boot debugging.
2013-10-20 21:03:15 +00:00
Ian Lepore
ac640932f4 Clock divisors 0-3 correspond to dividing by 1-4, so add 1 before dividing. 2013-10-19 21:33:06 +00:00
Rui Paulo
dd639923b9 Revert accidental commit. 2013-09-02 17:07:46 +00:00
Rui Paulo
530031a8f1 Initial support for the Digi ConnectCore(c) i.MX53 / Wi-i.MX53 boards.
There are many drivers missing, but we can reach single user mode now.

Hardware graciously donated by Douglas Beattie.
2013-09-01 20:15:35 +00:00
Ian Lepore
9908a5a5e1 Rename imx_machdep.c to imx51_machdep.c, because it contains hardware
addresses which are specific to the imx51 chips.
2013-08-13 21:12:28 +00:00
Ian Lepore
e0511b6c67 Add imx6 compatibility and make the driver work for any clock frequency.
There are still a couple references to imx51 ccm driver functions that will
need to be changed after an imx6 ccm driver is written.

Reviewed by:	ray
2013-08-13 13:14:13 +00:00
Ian Lepore
992a44320c Tweak the imx debug console code so that it works with multiple SoCs.
Instead of hard-coding the uart register addresses for the imx51, use
a variable that defaults to the imx51 address.  When debugging another
imx-family SoC, the variable can be set early in initarm() to provide
full console/printf support for debugging early boot.
2013-08-03 13:31:10 +00:00
Ian Lepore
2a2599f695 Rename the existing std.imx and imx.files to std.imx51 and files.imx51, to
pave the way for adding imx6 support.
2013-07-28 17:37:30 +00:00
Aleksandr Rybalko
94f8d6fdba Update copyright date. 2013-05-08 09:42:50 +00:00
Dimitry Andric
27e644a80b Fix undefined behaviour in several gpio_pin_setflags() routines (under
sys/arm and sys/mips), squelching the clang 3.3 warnings about this.

Noticed by:	tinderbox and many irate spectators
Submitted by:	Luiz Otavio O Souza <loos.br@gmail.com>
PR:		kern/177759
MFC after:	3 days
2013-04-13 21:21:13 +00:00
Aleksandr Rybalko
a2c472e741 Integrate Efika MX project back to home.
Sponsored by:	The FreeBSD Foundation
2013-03-20 15:39:27 +00:00