The MDIO bus frequency is configured as a divisor off of the MDIO bus
reference clock. For the AR9344 and later, the MDIO bus frequency can
be faster than normal (ie, up to 100MHz) and thus a static divisor may
not be very applicable.
So, for those boards that may require an actual frequency to be selected
regardless of what crazy stuff the vendor throws in uboot, one can now
set the MDIO bus frequency. It uses the MDIO frequency and the target
frequency to choose a divisor that doesn't exceed the target frequency.
By default it will choose:
* DIV_28 on everything; except
* DIV_58 on the AR9344 to be conservative.
Whilst I'm here, add some comments about the defaults being not quite
right. For the other internal switch devices (like the AR933x, AR724x)
the divisor can be higher - it's internal and the reference MDIO clock
is much lower than 100MHz.
The divisor tables and loop code is inspired from Linux/OpenWRT. It's very
simple; I didn't feel that reimplementing it would yield a substantially
different solution.
Tested:
* AR9331 (mips24k)
* AR9344 (mips74k)
Obtained from: Linux/OpenWRT
up and running.
* The MAC FIFO configurations needed updating;
* Reset the MDIO block at the same time the MAC block is reset;
* The default divisor needs changing as the DB120 runs at a higher
base MDIO bus clock compared to other chips.
The long-term fix is to allow the system to have a target MDIO bus
clock rate and then calculate the most suitable divider to meet
that. This will likely need implementing before stable external
PHY or switch support can be committed.
Tested:
* AR9344 (mips74k)
* AR9331 (mips24k)
add some packet(s) to tx ring and arge_stop() is called before receive the
sent packet interrupt from hardware. Fix arge_stop() to unload the in use
dma tags and free the associated mbuf.
PR: 178319, 163670
Approved by: adrian (mentor)
(re)start the interface when it is down. This change fix a race with
BOOTP where the response packet is lost because the interface is being
reset by a netmask change right after send the packet.
PR: 178318
Approved by: adrian (mentor)
form xx:xx:xx:xx:xx:xx complete with ":" characters taking of 18 bytes
instead of 6 integers. Expose a "readascii" tuneable to handle this case.
Remove restriction on eepromac assignement for the first dev instance only.
Add eepromac address for DIR-825 to hints file.
Add readascii hint for DIR-825
Reviewed by: adrian@
This seems to break at least my test board here (AR71xx + AR8316 switch
PHY). Since I do have a whole sleuth of "normal" PHY boards (with
an AR71xx on a normal PHY port), I'll do some further testing with those
to determine whether this is a general issue, or whether it's limited
to the behaviour of the "fake" dedicated PHY port mode on these atheros
switches.
* Flesh out the PLL configuration fetch function, which will return the PLL
configuration based on the unit number and speed.
* Remove the PLL speed config logic from the AR71xx/AR91xx chip PLL config
function - pass in a 'pll' value instead.
* Modify arge_set_pll() to:
+ fetch the PLL configuration
+ write the PLL configuration
+ update the MII speed configuration.
This will allow if_arge to override the PLL configuration as required.
Obtained from: Linux/Atheros/OpenWRT
This is only done if the ARGE_MDIO option is included.
* Shuffle the arge MDIO bus into a separate device, that needs to be
probed early (use hint.argemdio.X.order=0)
* hint.arge.X.mdio now specifies which miiproxy to rendezvous with.
* Call MAC/MDIO bus init during MDIO attach, not arge attach.
This is done regardless:
* Shift the arge MAC and MDIO bus reset code into separate functions
and call it early during MDIO bus attach. It's required for
correct MDIO bus IO to occur on AR71xx/AR91xx devices.
* Remove the AR71xx/AR91xx centric assumption that there's only one
MDIO bus. The initial code mapped miibus0(arge0) and miibus1(arge1)
MII register operations to the MII0 (arge0) register space. The
AR724x (and later, upcoming chipsets) have two MDIO busses and
the second is very much in use.
TODO:
* since the multiphy behaviour has changed (where now a phymask of >1
PHY will still be enumerated), multiphy setups may be quite wrong.
I'll go and fix these so they still have a chance of working, at least.
until the switch PHY support appears in -HEAD.
Submitted by: Stefan Bethke <stb@lassitu.de>
function.
From the submitter:
This patch fixes an issue I encountered using an NFS root with an
ar71xx-based MikroTik RouterBoard 450G on -current where the kernel fails
to contact a DHCP/BOOTP server via if_arge when it otherwise should be able
to. This may be the same issue that Monthadar Al Jaberi reported against
an RSPRO on 6 March, as the signature is the same:
%%%
DHCP/BOOTP timeout for server 255.255.255.255
DHCP/BOOTP timeout for server 255.255.255.255
DHCP/BOOTP timeout for server 255.255.255.255
.
.
.
DHCP/BOOTP timeout for server 255.255.255.255
DHCP/BOOTP timeout for server 255.255.255.255
arge0: initialization failed: no memory for rx buffers
DHCP/BOOTP timeout for server 255.255.255.255
arge0: initialization failed: no memory for rx buffers
%%%
The primary issue that I found is that the DHCP/BOOTP message that
bootpc_call() is sending never makes it onto the wire, which I believe is
due to the following:
- Last December, a change was made to the ifioctl that bootpc_call() uses
to adjust the netmask around the sosend().
- The new ioctl (SIOCAIFADDR) performs an if_init when invoked, whereas the
old one (SIOCSIFNETMASK) did not.
- if_arge maintains its own sense of link state in sc->arge_link_status.
- On a single-phy interface, sc->arge_link_status is initialized to 0 in
arge_init_locked().
- sc->arge_link_status remains 0 until a phy state change notification
causes arge_link_task to run, notice the link is up, and set it to 1.
- The inits caused by the ifioctls in bootpc_call are reinitializing the
interface, but not the phy, so sc->arge_link_status goes to 0 and remains
there.
- arge_start_locked() always sees sc->arge_link_status == 0 and returns
without queuing anything.
The attached patch changes arge_init_locked() such that in the single-phy
case, instead of initializing sc->arge_link_status to 0, it runs
arge_link_task() to set it according to the current phy state. This change
has allowed my setup to mount an NFS root successfully.
Submitted by: Patrick Kelsey <kelsey@ieee.org>
Reviewed by: juli
I had some interesting hangs until I realised I should try flushing the
DDR FIFO register and lo and behold, hangs stopped occuring.
I've put in a few DDR flushes here and there in case people decide to
reuse some of these functions. It's very very likely they're almost
all superflous.
To test:
* Connect to a network with a _lot_ of broadcast traffic
* Do this:
# while true; do ifconfig arge0 down; ifconfig arge0 up; done
This fixes the mbuf exhaustion that has been reported when the interface
state flaps up/down.
one. Interestingly, these are actually the default for quite some time
(bus_generic_driver_added(9) since r52045 and bus_generic_print_child(9)
since r52045) but even recently added device drivers do this unnecessarily.
Discussed with: jhb, marcel
- While at it, use DEVMETHOD_END.
Discussed with: jhb
- Also while at it, use __FBSDID.
Because driver is accessing a common MII structure in
mii_pollstat(), updating user supplied structure should be done
before dropping a driver lock.
Reported by: Karim (fodillemlinkarimi <> gmail dot com)
(reporting IFM_LOOP based on BMCR_LOOP is left in place though as
it might provide useful for debugging). For most mii(4) drivers it
was unclear whether the PHYs driven by them actually support
loopback or not. Moreover, typically loopback mode also needs to
be activated on the MAC, which none of the Ethernet drivers using
mii(4) implements. Given that loopback media has no real use (and
obviously hardly had a chance to actually work) besides for driver
development (which just loopback mode should be sufficient for
though, i.e one doesn't necessary need support for loopback media)
support for it is just dropped as both NetBSD and OpenBSD already
did quite some time ago.
- Let mii_phy_add_media() also announce the support of IFM_NONE.
- Restructure the PHY entry points to use a structure of entry points
instead of discrete function pointers, and extend this to include
a "reset" entry point. Make sure any PHY-specific reset routine is
always used, and provide one for lxtphy(4) which disables MII
interrupts (as is done for a few other PHYs we have drivers for).
This includes changing NIC drivers which previously just called the
generic mii_phy_reset() to now actually call the PHY-specific reset
routine, which might be crucial in some cases. While at it, the
redundant checks in these NIC drivers for mii->mii_instance not being
zero before calling the reset routines were removed because as soon
as one PHY driver attaches mii->mii_instance is incremented and we
hardly can end up in their media change callbacks etc if no PHY driver
has attached as mii_attach() would have failed in that case and not
attach a miibus(4) instance.
Consequently, NIC drivers now no longer should call mii_phy_reset()
directly, so it was removed from EXPORT_SYMS.
- Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe().
The purpose of that function is to perform the common steps to attach
a PHY driver instance and to hook it up to the miibus(4) instance and to
optionally also handle the probing, addition and initialization of the
supported media. So all a PHY driver without any special requirements
has to do in its bus attach method is to call mii_phy_dev_attach()
along with PHY-specific MIIF_* flags, a pointer to its PHY functions
and the add_media set to one. All PHY drivers were updated to take
advantage of mii_phy_dev_attach() as appropriate. Along with these
changes the capability mask was added to the mii_softc structure so
PHY drivers taking advantage of mii_phy_dev_attach() but still
handling media on their own do not need to fiddle with the MII attach
arguments anyway.
- Keep track of the PHY offset in the mii_softc structure. This is done
for compatibility with NetBSD/OpenBSD.
- Keep track of the PHY's OUI, model and revision in the mii_softc
structure. Several PHY drivers require this information also after
attaching and previously had to wrap their own softc around mii_softc.
NetBSD/OpenBSD also keep track of the model and revision on their
mii_softc structure. All PHY drivers were updated to take advantage
as appropriate.
- Convert the mebers of the MII data structure to unsigned where
appropriate. This is partly inspired by NetBSD/OpenBSD.
- According to IEEE 802.3-2002 the bits actually have to be reversed
when mapping an OUI to the MII ID registers. All PHY drivers and
miidevs where changed as necessary. Actually this now again allows to
largely share miidevs with NetBSD, which fixed this problem already
9 years ago. Consequently miidevs was synced as far as possible.
- Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that
weren't explicitly converted to support flow control before. It's
unclear whether flow control actually works with these but typically
it should and their net behavior should be more correct with these
changes in place than without if the MAC driver sets MIIF_DOPAUSE.
Obtained from: NetBSD (partially)
Reviewed by: yongari (earlier version), silence on arch@ and net@
levels. TX would hang, RX wouldn't. A bit of digging showed the interface
send queue was full, but IFF_DRV_OACTIVE was clear and the hardware TX
queue was empty.
It turns out that there wasn't a check to drain the interface send
queue once hardware TX had completed, so if the interface send queue
had filled up in the meantime, subsequent packets would be dropped
by the higher layers and if_start (and thus arge_start()) would never
be called.
The fix is simple - call arge_start_locked() in the software interrupt
handler after the hardware TX queue has been handled or a TX underrun
occured. This way the interface send queue gets drained.
offset in the flash.
Some devices (eg the TPLink WR-1043ND) don't have a flash environment
partition which can be queried for the current board settings.
This particular workaround allows for image creators to use a hint
to set the base MAC address. For example:
hint.arge.0.eeprommac=0x1f01fc00
The existing code only checked the alignment of the first mbuf and
didn't enforce the size constraints.
This commit introduces a simple function to check the alignment and
size of all mbufs in the list. This fixes the initial issue in the
PR.
PR: kern/148307
Reviewed by: gonzo@
queue length. The default value for this parameter is 50, which is
quite low for many of today's uses and the only way to modify this
parameter right now is to edit if_var.h file. Also add read-only
sysctl with the same name, so that it's possible to retrieve the
current value.
MFC after: 1 month
fixed-state media with parameters set via hints
and configure MAC accordingly to these parameters.
All the underlying PHY magic is done by boot manager
on startup. At the moment there is no proper way
to make active and control all PHYs simultaneously
from one MII bus and there is no way to associate
incoming/outgoing packet with specific PHY.
