This fixes 32-bit compat (no ioctl command defintions are required
as struct ifreq is the same size). This is believed to be sufficent to
fully support ifconfig on 32-bit systems.
Reviewed by: kib
Obtained from: CheriBSD
MFC after: 1 week
Relnotes: yes
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D14900
error state.
If the device is in internal error state the hardware will not
generate completions. Just move on to destroy the resources.
Submitted by: slavash@
MFC after: 1 week
Sponsored by: Mellanox Technologies
Change page cleanup flow when in internal error to properly decrement
the page counts when reclaiming pages. That prevents timing out
waiting for extra pages that were actually cleaned up previously.
Submitted by: slavash@
MFC after: 1 week
Sponsored by: Mellanox Technologies
When a PCI error is detected the PCI state could be corrupt, don't
save it in that flow. Save the state after initialization. After
restoring the PCI state during slot reset save it again, restoring
the state destroys the previously saved state info.
Submitted by: slavash@
MFC after: 1 week
Sponsored by: Mellanox Technologies
Since the FW can be shared between PCI functions it is common that
more than one health poll will detected a failure, this can lead to
multiple resets.
The solution is to use a FW locking mechanism using semaphore space to
provide a way to synchronize between functions. The FW semaphore is
acquired via config cycle access. First the VSEC gateway must be
acquired, then the semaphore can be locked by writing a value to it
and confirmed it's locked by reading the same value back. The process
in the same to free the semaphore, except the value written should be
zero.
Submitted by: slavash@
MFC after: 1 week
Sponsored by: Mellanox Technologies
If a FW assert is considered fatal, indicated by a new bit in the
health buffer, reset the FW. After the reset, follow the normal
recovery flow.
Submitted by: slavash@
MFC after: 1 week
Sponsored by: Mellanox Technologies
Some mlx5 adapter firmware allows the driver to reset the firmware in
the event of an error. When a software reset is issued on any physical
function all PFs enter reset state. This is a recoverable condition.
The existing recovery flow was designed to allow the recovery of a
VF after a PF driver reload. This patch expands the scope of that
flow to recover PFs or VFs after a SW reset has been issued.
When a software reset is issued the following occurs:
1. The NIC interface mode is set to SW_RESET (7) while the reset is in
progress.
2. Once the reset completes the NIC interface mode is set to NIC
disabled (1).
After the reset has been issued (added in a subsequent patch) the
health poll for other functions will detect that the NIC interface
state has been set to disabled. This will cause it to enter the
existing recovery flow. If the PCI is still working (meaning it
doesn't return 0xff on all reads) it means recovery can proceed
immediately instead of waiting 60 seconds.
The error detetion has also been refactored to avoid incorrect or
misleading log messages.
Submitted by: slavash@
MFC after: 1 week
Sponsored by: Mellanox Technologies
When mlx5_enter_error_state() operation is forced by shutdown, the
messages surrounding setting the error state are not informational
and confuse users.
Submitted by: kib@
MFC after: 1 week
Sponsored by: Mellanox Technologies
This patch accumulates the following Linux commits:
- 8812c24d28f4972c4f2b9998bf30b1f2a1b62adf
net/mlx5: Add fast unload support in shutdown flow
- 59211bd3b6329c3e5f4a90ac3d7f87ffa7867073
net/mlx5: Split the load/unload flow into hardware and software flows
- 4525abeaae54560254a1bb8970b3d4c225d32ef4
net/mlx5: Expose command polling interface
Submitted by: Matthew Finlay <matt@mellanox.com>
MFC after: 1 week
Sponsored by: Mellanox Technologies
This patch accumulates the following Linux commits:
- 04c0c1ab38e95105d950db5b84e727637e149ce7
net/mlx5: PCI error recovery health care simulation
- 0179720d6be2096b8d0a4d143254ff9e77747daa
net/mlx5: Introduce trigger_health_work function
- 3fece5d676939f42f434c63dfe1bd42d7d94e6f0
net/mlx5: Continue health polling until it is explicitly stopped
Submitted by: Matthew Finlay <matt@mellanox.com>
MFC after: 1 week
Sponsored by: Mellanox Technologies
The mlx5e_destroy_ifp() function may be called from the system workqueue and
in this case trying to flush all works will cause a dead lock.
Instead of using the system workqueue, create a designated workqueue
for each mlx5en(4) device instance.
Submitted by: slavash@
MFC after: 1 week
Sponsored by: Mellanox Technologies
There is a difference when parsing a completion entry between Ethernet
and IB ports. When link layer is Ethernet the bits describe the type of
L3 header in the packet. In the case when link layer is Ethernet and VLAN
header is present the value of SL is equal to the 3 UP bits in the VLAN
header. If VLAN header is not present then the SL is undefined and consumer
of the completion should check if IB_WC_WITH_VLAN is set.
While that, this patch also fills the vlan_id field in the completion if
present.
linux commit 12f8fedef2ec94c783f929126b20440a01512c14
MFC after: 1 week
Sponsored by: Mellanox Technologies
mlx5core.
Do not consider the inability to create a firmware dump fatal, but
inform about the situation and allow the driver to attach. The device
might not implement the needed VSC, or we might not know the layout of
the registers map. In either case, only firmware dump functionality is
limited, the network operations should be fine.
Submitted by: kib@
MFC after: 1 week
Sponsored by: Mellanox Technologies
When the mlx5en(4) driver was converted to using BUSDMA(9) the call to
m_defrag() was moved after the part of the TX routine that strips the
header from the mbuf chain. Before it called m_defrag it first trimmed
off the now-empty mbufs from the start of the chain. This has the side
effect of also removing the head of the chain that has M_PKTHDR set.
m_defrag() will not defrag a chain that does not have M_PKTHDR set,
thus it was effectively never defragging the mbuf chains.
As it turns out, trimming the mbufs in this fashion is unnecessary since
the call to bus_dmamap_load_mbuf_sg doesn't map empty mbufs anyway, so
remove it.
Differential Revision: https://reviews.freebsd.org/D12050
Submitted by: mjoras@
MFC after: 1 week
Sponsored by: Mellanox Technologies
Set and report vport MTU rather than physical MTU,
The driver will set both vport and physical port mtu
and will rely on the query of vport mtu.
SRIOV VFs have to report their MTU to their vport manager (PF),
and this will allow them to work with any MTU they need
without failing the request.
Also for some cases where the PF is not a port owner, PF can
work with MTU less than the physical port mtu if set physical
port mtu didn't take effect.
Based on Linux upstream commit:
cd255efff9baadd654d6160e52d17ae7c568c9d3
Submitted by: Meny Yossefi <menyy@mellanox.com>
MFC after: 1 week
Sponsored by: Mellanox Technologies
Currently the ifnet interface is named mceX, where X is a monotonically
incremented value. If the device is reset due to a fatal error, then the
interface name will change. Using the device unit number will keep the
naming consistent across the reset logic.
Submitted by: Matthew Finlay <matt@mellanox.com>
MFC after: 1 week
Sponsored by: Mellanox Technologies
ConnectX-4/5 devices in mlx5core.
The dump is obtained by reading a predefined register map from the
non-destructive crspace, accessible by the vendor-specific PCIe
capability (VSC). The dump is stored in preallocated kernel memory and
managed by the mlx5tool(8), which communicates with the driver using a
character device node.
The utility allows to store the dump in format
<address> <value>
into a file, to reset the dump content, and to manually initiate the
dump.
A call to mlx5_fwdump() should be added at the places where a dump
must be fetched automatically. The most likely place is right before a
firmware reset request.
Submitted by: kib@
MFC after: 1 week
Sponsored by: Mellanox Technologies
Add the ability to access the vendor specific space gateway in order
to support reading and writing data into the different configuration
domains.
Submitted by: Matthew Finlay <matt@mellanox.com>
MFC after: 1 week
Sponsored by: Mellanox Technologies
Add support for PFC and implement reading the per priority statistics
using the sysctl(8) interface. PFC is used together with VLAN priority
and can be enabled and disabled on a per priority basis.
Global pause frames and PFC are incompatible features and surrounding
logic has been added to warn the user about misconfiguration.
Update relevant mlx5core APIs for PFC configuration.
MFC after: 1 week
Sponsored by: Mellanox Technologies
ECN configuration and statistics is available through a set of sysctl(8)
nodes under sys.class.infiniband.mlx5_X.cong . The ECN configuration
nodes can also be used as loader tunables.
MFC after: 1 week
Sponsored by: Mellanox Technologies
This patch accumulates the following Linux commits:
mlx5_health.c
- 78ccb25861d76a8fc5c678d762180e6918834200
mlx5_core: Fix wrong name in struct
- 171bb2c560f45c0427ca3776a4c8f4e26e559400
mlx5_core: Update health syndromes
- 0144a95e2ad53a40c62148f44fb0c1f9d2a0d1e9
mlx5_core: Use accessor functions to read from device memory
- ac6ea6e81a80172612e0c9ef93720f371b198918
mlx5_core: Use private health thread for each device
- fd76ee4da55abb21babfc69310d321b9cb9a32e0
mlx5_core: Fix internal error detection conditions
- 2241007b3d783cbdbaa78c30bdb1994278b6f9b9
mlx5: Clear health sick bit when starting health poll
- 712bfef60912d91033cb25739f7444d5b8d8c59f
mlx5: Fix version printout in case of health issue
- 89d44f0a6c732db23b219be708e2fe1e03ee4842
mlx5_core: Add pci error handlers to mlx5_core driver
mlx5_cmd.c
- be87544de8df2b1eb34bcb5e32691287d96f9ec4
mlx5_core: Fix async commands return code
- a31208b1e11df334d443ec8cace7636150bb8ce2
mlx5_core: New init and exit flow for mlx5_core
- 020446e01eebc9dbe7eda038e570ab9c7ab13586
mlx5_core: Prepare cmd interface to system errors handling
- 89d44f0a6c732db23b219be708e2fe1e03ee4842
mlx5_core: Add pci error handlers to mlx5_core driver
- 0d834442cc247c7b3f3bd6019512ae03e96dd99a
mlx5: Fix teardown errors that happen in pci error handler
mlx5_main.c
- 5fc7197d3a256d9c5de3134870304b24892a4908
mlx5: Add pci shutdown callback
Submitted by: Matthew Finlay <matt@mellanox.com>
MFC after: 1 week
Sponsored by: Mellanox Technologies
Add support for mapping priority to traffic class via sysctl
Submitted by: Slava Shwartsman <slavash@mellanox.com>
MFC after: 1 week
Sponsored by: Mellanox Technologies
- Factor out port speed definitions into new port.h header file,
similarly as done in Linux upstream.
- Correct two existing port speed definitions in mlx5en according to
Linux upstream.
MFC after: 1 week
Sponsored by: Mellanox Technologies
Adding an interface might be done outside the device_attach() routine
and will then cause a panic, due to the VNET not being set.
MFC after: 1 week
Sponsored by: Mellanox Technologies
The current implementation does not handle timeout in case of command
with callback request, and this can lead to deadlock if the command
doesn't get firmware response. Add delayed callback timeout work
before posting the command to firmware. In case of real firmware
command completion we will cancel the delayed work. In case of
firmware command timeout the callback timeout handler will be called
and it will simulate firmware completion with timeout error.
linux commit 65ee67084589c1783a74b4a4a5db38d7264ec8b5
MFC after: 1 week
Sponsored by: Mellanox Technologies
Call command completion handler in case of timeout when working in
interrupts mode. Avoid flushing the commands workqueue after acquiring
the semaphores to prevent a potential deadlock.
linux commit commit 9cba4ebcf374c3772f6eb61f2d065294b2451b49
MFC after: 1 week
Sponsored by: Mellanox Technologies
Creating a UD address handle from user-space or from the kernel-space,
when the link layer is ethernet, requires resolving the remote L3
address into a L2 address. Doing this from the kernel is easy because
the required ARP(IPv4) and ND6(IPv6) address resolving APIs are readily
available. In userspace such an interface does not exist and kernel
help is required.
It should be noted that in an IP-based GID environment, the GID itself
does not contain all the information needed to resolve the destination
IP address. For example information like VLAN ID and SCOPE ID, is not
part of the GID and must be fetched from the GID attributes. Therefore
a source GID should always be referred to as a GID index. Instead of
going through various racy steps to obtain information about the
GID attributes from user-space, this is now all done by the kernel.
This patch optimises the L3 to L2 address resolving using the existing
create address handle uverbs interface, retrieving back the L2 address
as an additional user-space information structure.
This commit combines the following Linux upstream commits:
IB/core: Let create_ah return extended response to user
IB/core: Change ib_resolve_eth_dmac to use it in create AH
IB/mlx5: Make create/destroy_ah available to userspace
IB/mlx5: Use kernel driver to help userspace create ah
IB/mlx5: Report that device has udata response in create_ah
MFC after: 1 week
Sponsored by: Mellanox Technologies
checks to recognize own network devices when using mlx5ib. This patch fixes
an issues where mlx5ib fails to recognize mceX network devices for use with
RoCE.
MFC after: 1 week
Sponsored by: Mellanox Technologies
The IA32 memory model guarantees that all writes are seen in the program
order. Also, any access to the uncacheable memory flushes the store
buffers. As the consequence, SFENCE instruction is (almost) never needed,
in particular, it is not needed to ensure the correct order of updates as
seen by a PCIe device.
Use atomic_thread_fence_rel() instead of wb() to only emit compiler barriers
on x86 there. Other architectures get the right barrier instruction as
well.
Reviewed by: hselasky
Sponsored by: Mellanox Technologies
MFC after: 1 week
Driver support is only provided for ConnectX4/5.
System-time timestamp is calculated based on the free-running counter
timestamp provided by hardware. Driver periodically samples the
counter to calibrate it against the system clock and uses linear
interpolation to convert. Stability of the crystal which drives the
clock is +-50 ppm at the operational temperature, which makes the
algorithm good enough.
The calculation is somewhat delicate because all values are 64bit and
overflow the naive formula for linear interpolation. The calculation
drops the least significant bits in advance, see the PREC shift in
mlx5_mbuf_tstmp().
Hardware stamps can be turned off by 'ifconfig mceN -hwrxtsmp'. Buggy
firmware might result in small but visible errors in the reported
timestamps, detectable e.g. by nonsensical (negative) RTT values for
LAN pings.
Reviewed by: gallatin, hselasky
Sponsored by: Mellanox Technologies
Differential revision: https://reviews.freebsd.org/D12638
Different compilers may optimise the enum type in different ways. This ensures
coherency when range checking the value of enums in ibcore.
Sponsored by: Mellanox Technologies
MFC after: 1 week
The hardware is capable of 2 requestor endianness modes for standard 8
byte atomics: BE (0x0) and host endianness (0x1). Read the supported
modes from hca atomic capabilities and configure HW to host endianness
mode if supported.
Sponsored by: Mellanox Technologies
MFC after: 1 week
the coming ibcore and mlx5ib updates in order to support traffic redirection
to so-called raw ethernet QPs.
Remove unused E-switch related routines and files while at it.
Sponsored by: Mellanox Technologies
MFC after: 1 week
iWarp and RoCE in ibcore. The selection of RDMA_PS_TCP can not be used
to indicate iWarp protocol use. Backport the proper IB device
capabilities from Linux upstream to distinguish between iWarp and
RoCE. Only allocate the additional socket required for iWarp for RDMA
IDs when at least one iWarp device present. This resolves
interopability issues between iWarp and RoCE in ibcore
Reviewed by: np @
Differential Revision: https://reviews.freebsd.org/D12563
Sponsored by: Mellanox Technologies
MFC after: 3 days
Remote DMA over Converged Ethernet, RoCE, for the ConnectX-4 series of
PCI express network cards.
There is currently no user-space support and this driver only supports
kernel side non-routable RoCE V1. The krping kernel module can be used
to test this driver. Full user-space support including RoCE V2 will be
added as part of the ongoing upgrade to ibcore from Linux 4.9. Otherwise
this driver is feature equivalent to mlx4ib(4). The mlx5ib(4) kernel
module will only be built when WITH_OFED=YES is specified.
MFC after: 2 weeks
Sponsored by: Mellanox Technologies
input errors in the mlx5en(4) driver. This improves the sysadmin view of
physical port errors.
Submitted by: gallatin@
MFC after: 1 week
Sponsored by: Mellanox Technologies
Code inspection reveals the busdma unload and free functions
do not write to the belonging dma tag and does not need to be
serialized. This allows mlx5_fwp_free() to be called from
software interrupt context.
MFC after: 3 days
Sponsored by: Mellanox Technologies
Add io_mapping_init_wc() and add a third (unused) parameter to
io_mapping_map_wc().
Reviewed by: hselasky
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D11286
The MLX5 driver has four different types of DMA allocations which are
now allocated using busdma:
1) The 4K firmware DMA-able blocks. One busdma object per 4K allocation.
2) Data for firmware commands use the 4K firmware blocks split into four 1K blocks.
3) The 4K firmware blocks are also used for doorbell pages.
4) The RQ-, SQ- and CQ- DMA rings. One busdma object per allocation.
After this patch the mlx5en driver can be used with DMAR enabled in
the FreeBSD kernel.
MFC after: 1 week
Sponsored by: Mellanox Technologies
- When device disappears from PCI indicate error device state and:
1) Trigger command completion for all pending commands
2) Prevent new commands from executing and return:
- success for modify and remove/cleanup commands
- failure for create/query commands
3) When reclaiming pages for a device in error state don't ask FW to
return all given pages, just release the allocated memory
MFC after: 1 week
Sponsored by: Mellanox Technologies
PCI device(s), changes:
- alloc_entry() now clears bit for page slot entry aswell
- update of cmd->ent_arr[] is now under cmd->alloc_lock
- complete command if alloc_entry() fails
MFC after: 1 week
Sponsored by: Mellanox Technologies
By default reading the diagnostic counters is disabled. The firmware
decides which counters are supported and only those supported show up
in the dev.mce.X.diagnostics sysctl tree.
To enable reading of diagnostic counters set one or more of the
following sysctls to one:
dev.mce.X.conf.diag_general_enable=1
dev.mce.X.conf.diag_pci_enable=1
MFC after: 1 week
Sponsored by: Mellanox Technologies
consistent return values from the mlx5e_sq_has_room_for()
function. The two counters are incremented by different threads under
different locks.
MFC after: 1 week
Sponsored by: Mellanox Technologies
- Add new sysctl node to control the transmit packet bufring.
- Add optimised version of the transmit routine which output packets
directly to the DMA ring instead of using bufring in case the transmit
lock is congested. This can reduce the number of taskswitches which in
turn influence the overall system CPU usage, depending on the
workload.
- Add " TX" suffix to debug name for transmit mutexes to silence some
witness warnings about aquiring duplicate locks having same name.
MFC after: 1 week
Sponsored by: Mellanox Technologies
Suggested by: gallatin @
Add own state variable to track if a sendqueue is stopped or not.
This will prevent traffic from entering the sendqueue while it is
being destroyed.
Update drain function to wait for traffic to be transmitted before
returning when the link state is active.
Add extra checks in transmit path for stopped SQ's.
While at it:
- Use likely() for a mbuf pointer check.
- Remove redundant IFF_DRV_RUNNING check.
MFC after: 1 week
Sponsored by: Mellanox Technologies
The firmware/hardware does not generate additional completion
events unless we post new buffers. Use a timer to try to post
more buffers in case we are temporarily out of mbufs. Else
the receive schedule completely stops.
Sponsored by: Mellanox Technologies
MFC after: 1 week
When mlx5e_sq_xmit() returns an error code and the mbuf pointer is set,
we should not free the mbuf, because the caller will keep the mbuf in
the drbr. Make sure the mbuf pointer is correctly set upon function
exit.
Sponsored by: Mellanox Technologies
MFC after: 1 week
The hardware MTU size can't be set to a value less than 1500 bytes due
to side-band management support. Allow setting the software MTU size
below 1500 bytes, thus creating a mismatch between hardware and
software MTU sizes.
Sponsored by: Mellanox Technologies
MFC after: 1 week
Try to reuse code to setup sendqueues when possible by making some static
functions global. Further split the mlx5e_close_sq_wait() function to
separate out reusable parts.
Sponsored by: Mellanox Technologies
MFC after: 1 week
This change also reduces the size of the mlx5e_sq structure so that the last
queue_state element will fit into the previous cacheline and then the mlx5e_sq
structure becomes one cacheline less for amd64.
Sponsored by: Mellanox Technologies
MFC after: 1 week
Make some functions and structures global to allow for code reuse
when creating rate limiting sendqueues.
Sponsored by: Mellanox Technologies
MFC after: 1 week
Move setting of CQ moderation mode together with the other
CQ moderation parameters. Pass completion event vector as
a separate argument to mlx5e_open_cq(), because its value is
different for each call. Pass mlx5e_priv pointer instead of
mlx5e_channel pointer so that code can be used by rate
limiting sendqueues.
Sponsored by: Mellanox Technologies
MFC after: 1 week
This change allows for reusing the transmit path for so called
rate limited senqueues. While at it optimise some pointer lookups
in the fast path.
Sponsored by: Mellanox Technologies
MFC after: 1 week
- Add new firmware commands and update existing ones.
- Add more firmware related structures and update existing ones.
- Some minor fixes, like adding missing \n to some prints.
Sponsored by: Mellanox Technologies
MFC after: 1 week
Clear the device description to avoid use after free because the
bsddev is not destroyed when the mlx5en module is unloaded. Only when
the parent mlx5 module is unloaded the bsddev is destroyed. This fixes
a panic on listing sysctls which refer strings in the bsddev after the
mlx5en module has been unloaded.
Sponsored by: Mellanox Technologies
MFC after: 1 week
driver. This change significantly increases the overall RX aggregation
ratio for heavily loaded networks handling 10-80 thousand simultaneous
connections.
Remove the turbo LRO code and all references to it which has now been
superceeded by the tcp_lro_queue_mbuf() function.
Tested by: Netflix
Sponsored by: Mellanox Technologies
MFC after: 1 week
This patch adds the missing pieces needed for device setup using the
mlx5en driver inside a virtual machine which is providing hardware
access through SR-IOV.
Sponsored by: Mellanox Technologies
MFC after: 1 week
tunable SYSCTL's. Linux module parameters are associated with the
module they belong to. FreeBSD does not share this concept of a parent
module. Instead add macros which define the prefix to use for the
module parameters in the LinuxKPI consumers.
While at it convert all "bool" LinuxKPI module parameters to "byte"
type, because we don't have a "bool" type of SYSCTL in FreeBSD.
Sponsored by: Mellanox Technologies
MFC after: 1 week
Store the last doorbell write in the mlx5e_sq structure and write the
doorbell to the hardware when the transmit routine finishes
transmitting all queued mbufs.
Sponsored by: Mellanox Technologies
Tested by: Netflix
MFC after: 1 week
This patch implements a sysctl which allows setting a factor, N, for
how many work queue elements can be generated before requiring a
completion event. When a completion event happens the code simulates N
completion events instead of only one. When draining a transmit queue,
N-1 NOPs are transmitted at most, to force generation of the final
completion event. Further a timer is running every HZ ticks to flush
any remaining data off the transmit queue when the tx_completion_fact
> 1.
The goal of this feature is to reduce the PCI bandwidth needed when
transmitting data.
Sponsored by: Mellanox Technologies
Tested by: Netflix
MFC after: 1 week
function to error out early when no port module is present and doing
eeprom access. This also prevents error codes from filling up in
dmesg.
Sponsored by: Mellanox Technologies
Tested by: Netflix
MFC after: 1 week
And factor out tcp_lro_rx_done, which deduplicates the same logic with
netinet/tcp_lro.c
Reviewed by: gallatin (1st version), hps, zbb, np, Dexuan Cui <decui microsoft com>
Sponsored by: Microsoft OSTC
Differential Revision: https://reviews.freebsd.org/D5725
after changing the HW LRO sysctl when previously in up state.
Reviewed by: gnn
Sponsored by: Mellanox Technologies
MFC after: 5 days
Differential Revision: https://reviews.freebsd.org/D4941
coalescing and zipping multiple CQEs into a single merged CQE. The
feature is enabled by default and can be disabled by a sysctl.
Implementing this feature mlx5_cqwq_pop() has been separated from
mlx5e_get_cqe().
MFC after: 1 week
Submitted by: Mark Bloch <markb@mellanox.com>
Differential Revision: https://reviews.freebsd.org/D4598
Sponsored by: Mellanox Technologies
include the following list of changes:
- Added eswitch ACL table management
Introduce API for managing ACL table.
This API include the following features:
1) vlan filter - for VST/VGT+ support.
2) spoofcheck.
3) robust functionality to allow/drop general untagged/tagged traffic.
4) support for both ingress and egress ACL types.
- Added loopback filter to the vacl table.
- Added multicast list set in the vPort context
- Added promiscuous mode set in the vPort context
- Set the vlan list in vPort context
1) Check caps if VLAN list is not longer than FW supports
2) Set MODIFY_NIC_VPORT_CONTEXT command
- Changed MLX5_EEPROM_MAX_BYTES from 48 to 32 so that a single EEPROM
reading cannot cross the 128-byte boundary. Previously reading the
MCIA register was done in batches of 48 bytes. The third reading
would then by-pass the 127th byte, which means that part of the low
page and part of the high page would be read at the same time, which
created a bug:
1st: 0-47 bytes
2nd: 48-95 bytes
3rd: 96-143 bytes
MFC after: 1 week
Sponsored by: Mellanox Technologies
Differential Revision: https://reviews.freebsd.org/D4411
driver. This includes binding all interrupt and worker threads
according to the RSS configuration, setting up correct Toeplitz
hashing keys as given by RSS and setting the correct mbuf
hashtype for all received traffic.
MFC after: 1 week
Sponsored by: Mellanox Technologies
Differential Revision: https://reviews.freebsd.org/D4410
completion events can be moderated in the same way like RX completion
events. Expose this functionality by a sysctl variable.
MFC after: 1 week
Sponsored by: Mellanox Technologies
Differential Revision: https://reviews.freebsd.org/D4409
Set the port MTU and then query it and report if any problems instead.
MFC after: 1 week
Submitted by: Shahar Klein <shahark@mellanox.com>
Sponsored by: Mellanox Technologies
Differential Revision: https://reviews.freebsd.org/D4408
RX buffers from number of received packets.
Differential Revision: https://reviews.freebsd.org/D4178
Submitted by: Drew Gallatin <gallatin@freebsd.org>
Sponsored by: Mellanox Technologies
MFC after: 3 days
Setting sysctl dev....conf.hw_lro may fail if the net device lro is
turned off. Due to the nature of our sysctl handler we need to set the
values back to 0 and issue an error.
Differential Revision: https://reviews.freebsd.org/D4177
Submitted by: Shahar Klein <shahark@mellanox.com>
Sponsored by: Mellanox Technologies
MFC after: 3 days
from Mellanox Technologies. The current driver supports ethernet
speeds up to and including 100 GBit/s. Infiniband support will be
done later.
The code added is not compiled by default, which will be done by a
separate commit.
Sponsored by: Mellanox Technologies
MFC after: 2 weeks