Add printf() wrapper to use CR/CRLF terminators depending on whether
stdio is mapped to a tty open in raw mode.
Try to use the wrapper everywhere.
For now we leave the custom DPRINTF/WPRINTF defined by device
models, but we may remove them in the future.
Reviewed by: grehan, jhb
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D22657
Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
No functional change intended.
the legacy 8259A PICs.
- Implement an ICH-comptabile PCI interrupt router on the lpc device with
8 steerable pins configured via config space access to byte-wide
registers at 0x60-63 and 0x68-6b.
- For each configured PCI INTx interrupt, route it to both an I/O APIC
pin and a PCI interrupt router pin. When a PCI INTx interrupt is
asserted, ensure that both pins are asserted.
- Provide an initial routing of PCI interrupt router (PIRQ) pins to
8259A pins (ISA IRQs) and initialize the interrupt line config register
for the corresponding PCI function with the ISA IRQ as this matches
existing hardware.
- Add a global _PIC method for OSPM to select the desired interrupt routing
configuration.
- Update the _PRT methods for PCI bridges to provide both APIC and legacy
PRT tables and return the appropriate table based on the configured
routing configuration. Note that if the lpc device is not configured, no
routing information is provided.
- When the lpc device is enabled, provide ACPI PCI link devices corresponding
to each PIRQ pin.
- Add a VMM ioctl to adjust the trigger mode (edge vs level) for 8259A
pins via the ELCR.
- Mark the power management SCI as level triggered.
- Don't hardcode the number of elements in Packages in the source for
the DSDT. iasl(8) will fill in the actual number of elements, and
this makes it simpler to generate a Package with a variable number of
elements.
Reviewed by: tycho
because there isn't a standard way to relay this information to the guest OS.
Add a command line option "-Y" to bhyve(8) to inhibit MPtable generation.
If the virtual machine is using PCI devices on buses other than 0 then it can
still use ACPI tables to convey this information to the guest.
Discussed with: grehan@
This is done by representing each bus as root PCI device in ACPI. The device
implements the _BBN method to return the PCI bus number to the guest OS.
Each PCI bus keeps track of the resources that is decodes for devices
configured on the bus: i/o, mmio (32-bit) and mmio (64-bit). These windows
are advertised to the guest via the _CRS object of the root device.
Bus 0 is treated specially since it consumes the I/O ports to access the
PCI config space [0xcf8-0xcff]. It also decodes the legacy I/O ports that
are consumed by devices on the LPC bus. For this reason the LPC bridge can
be configured only on bus 0.
The bus number can be specified using the following command line option
to bhyve(8): "-s <bus>:<slot>:<func>,<emul>[,<config>]"
Discussed with: grehan@
Reviewed by: jhb@
the virtio backends.
- Add a new ioctl to export the count of pins on the I/O APIC from vmm
to the hypervisor.
- Use pins on the I/O APIC >= 16 for PCI interrupts leaving 0-15 for
ISA interrupts.
- Populate the MP Table with I/O interrupt entries for any PCI INTx
interrupts.
- Create a _PRT table under the PCI root bridge in ACPI to route any
PCI INTx interrupts appropriately.
- Track which INTx interrupts are in use per-slot so that functions
that share a slot attempt to distribute their INTx interrupts across
the four available pins.
- Implicitly mask INTx interrupts if either MSI or MSI-X is enabled
and when the INTx DIS bit is set in a function's PCI command register.
Either assert or deassert the associated I/O APIC pin when the
state of one of those conditions changes.
- Add INTx support to the virtio backends.
- Always advertise the MSI capability in the virtio backends.
Submitted by: neel (7)
Reviewed by: neel
MFC after: 2 weeks
to SIGTERM when ACPI is enabled. Sending SIGTERM to the hypervisor when an
ACPI-aware OS is running will now trigger a soft-off allowing for a graceful
shutdown of the guest.
- Move constants for ACPI-related registers to acpi.h.
- Implement an SMI_CMD register with commands to enable and disable ACPI.
Currently the only change when ACPI is enabled is to enable the virtual
power button via SIGTERM.
- Implement a fixed-feature power button when ACPI is enabled by asserting
PWRBTN_STS in PM1_EVT when SIGTERM is received.
- Add support for EVFILT_SIGNAL events to mevent.
- Implement support for the ACPI system command interrupt (SCI) and assert
it when needed based on the values in PM1_EVT. Mark the SCI as active-low
and level triggered in the MADT and MP Table.
- Mark PCI interrupts in the MP Table as active-low in addition to level
triggered.
Reviewed by: neel
- Add a generic routine to trigger an LVT interrupt that supports both
fixed and NMI delivery modes.
- Add an ioctl and bhyvectl command to trigger local interrupts inside a
guest. In particular, a global NMI similar to that raised by SERR# or
PERR# can be simulated by asserting LINT1 on all vCPUs.
- Extend the LVT table in the vCPU local APIC to support CMCI.
- Flesh out the local APIC error reporting a bit to cache errors and
report them via ESR when ESR is written to. Add support for asserting
the error LVT when an error occurs. Raise illegal vector errors when
attempting to signal an invalid vector for an interrupt or when sending
an IPI.
- Ignore writes to reserved bits in LVT entries.
- Export table entries the MADT and MP Table advertising the stock x86
config of LINT0 set to ExtInt and LINT1 wired to NMI.
Reviewed by: neel (earlier version)
commit level triggered interrupts would work as long as the pin was not shared
among multiple interrupt sources.
The vlapic now keeps track of level triggered interrupts in the trigger mode
register and will forward the EOI for a level triggered interrupt to the
vioapic. The vioapic in turn uses the EOI to sample the level on the pin and
re-inject the vector if the pin is still asserted.
The vhpet is the first consumer of level triggered interrupts and advertises
that it can generate interrupts on pins 20 through 23 of the vioapic.
Discussed with: grehan@
actual value read by the guest from the device. The IOAPIC ID is now set to
zero in both MPtable/ACPI tables as well as in the ioapic device emulation.
Pointed out by: grehan@
- Allow a hostbridge to be created with AMD as a vendor.
This passes the OpenBSD check to allow the use of MSI
on a PCI bus.
- Enable the i/o interrupt section of the mptable, and
populate it with unity ISA mappings. This allows the
'legacy' IRQ mappings of the PCI serial port to be
set up. Delete unused print routine that was obscuring code.
- Use the '-W' option to enable virtio single-vector MSI
rather than an environment variable. Update the virtio
net/block drivers to query this flag when setting up
interrupts.: bhyverun.c
- Fix the arithmetic used to derive the century byte in
RTC CMOS, as well as encoding it in BCD.
Reviewed by: neel
MFC after: 3 days
command line option "-m <memsize in MB>" to specify the memory size.
Prior to this change the user needed to explicitly specify the amount of
memory allocated below 4G (-m <lowmem>) and the amount above 4G (-M <highmem>).
The "-M" option is no longer supported by 'bhyveload' and 'bhyve'.
The start of the PCI hole is fixed at 3GB and cannot be directly changed
using command line options. However it is still possible to change this in
special circumstances via the 'vm_set_lowmem_limit()' API provided by
libvmmapi.
Submitted by: Dinakar Medavaram (initial version)
Reviewed by: grehan
Obtained from: NetApp
This seems prudent to do in its own right but it also opens up the possibility
of not having to mmap the entire guest address space in the 'bhyve' process
context.
Discussed with: grehan
Obtained from: NetApp
bhyve is intended to be a generic hypervisor, and not FreeBSD-specific.
(renaming internal routines will come later)
Reviewed by: neel
Obtained from: NetApp
Firmware tables require too much knowledge of system configuration,
and it's difficult to pass that information in general terms to a library.
The upcoming ACPI work exposed this - it will also livein bhyve.
Also, remove code specific to NetApp from the mptable name, and remove
the -n option from bhyve.
Reviewed by: neel
Obtained from: NetApp
