I added this block, knowing that lint does not support _Thread_local.
When linting, we could argue that we don't care about TLS (yet). It
seems, however, that external pieces of software also sometimes do a
-Dlint, regex the output and compile it again.
Reported by: swills
apply to most jails but do apply to vnet jails. This includes adding
a new sysctl "security.jail.vnet" to identify vnet jails.
PR: conf/149050
Submitted by: mdodd
MFC after: 3 days
Group onboard mic and headphone mic jack together. Creates association that
will switch between microphone inputs depending on the state of the headphone
jack being connected to a live mic.
Fixes onboard mic not working at all on T520.
Tested on T520, T420.
Suspect X220 needs this too, untested on.
MFC after: 1 month
The list-based DMA engine has the following behaviour:
* When the DMA engine is in the init state, you can write the first
descriptor address to the QCU TxDP register and it will work.
* Then when it hits the end of the list (ie, it either hits a NULL
link pointer, OR it hits a descriptor with VEOL set) the QCU
stops, and the TxDP points to the last descriptor that was transmitted.
* Then when you want to transmit a new frame, you can then either:
+ write the head of the new list into TxDP, or
+ you write the head of the new list into the link pointer of the
last completed descriptor (ie, where TxDP points), then kick
TxE to restart transmission on that QCU>
* The hardware then will re-read the descriptor to pick up the link
pointer and then jump to that.
Now, the quirks:
* If you write a TxDP when there's been no previous TxDP (ie, it's 0),
it works.
* If you write a TxDP in any other instance, the TxDP write may actually
fail. Thus, when you start transmission, it will re-read the last
transmitted descriptor to get the link pointer, NOT just start a new
transmission.
So the correct thing to do here is:
* ALWAYS use the holding descriptor (ie, the last transmitted descriptor
that we've kept safe) and use the link pointer in _THAT_ to transmit
the next frame.
* NEVER write to the TxDP after you've done the initial write.
* .. also, don't do this whilst you're also resetting the NIC.
With this in mind, the following patch does basically the above.
* Since this encapsulates Sam's issues with the QCU behaviour w/ TDMA,
kill the TDMA special case and replace it with the above.
* Add a new TXQ flag - PUTRUNNING - which indicates that we've started
DMA.
* Clear that flag when DMA has been shutdown.
* Ensure that we're not restarting DMA with PUTRUNNING enabled.
* Fix the link pointer logic during TXQ drain - we should always ensure
the link pointer does point to something if there's a list of frames.
Having it be NULL as an indication that DMA has finished or during
a reset causes trouble.
Now, given all of this, i want to nuke axq_link from orbit. There's now HAL
methods to get and set the link pointer of a descriptor, so what we
should do instead is to update the right link pointer.
* If there's a holding descriptor and an empty TXQ list, set the
link pointer of said holding descriptor to the new frame.
* If there's a non-empty TXQ list, set the link pointer of the
last descriptor in the list to the new frame.
* Nuke axq_link from orbit.
Note:
* The AR9380 doesn't need this. FIFO TX writes are atomic. As long as
we don't append to a list of frames that we've already passed to the
hardware, all of the above doesn't apply. The holding descriptor stuff
is still needed to ensure the hardware can re-read a completed
descriptor to move onto the next one, but we restart DMA by pushing in
a new FIFO entry into the TX QCU. That doesn't require any real
gymnastics.
Tested:
* AR5210, AR5211, AR5212, AR5416, AR9380 - STA mode.
Most likely some non-USB compliant devices will choke on it
sooner or later. Clear stall is strictly speaking not needed.
If the first MIDI command sent or transmitted is lost, this
is not a big problem for us.
MFC after: 1 week
Set a valid alternate interface setting
when enumerating USB audio devices else
the device mentioned will not work like
expected.
PR: usb/178722
MFC after: 1 week
o The CP2101 and CP2102 do not support GPIO pin use at all, enforce this.
o Support reading the GPIO status on the second port of the CP2105. More
work is needed before the CP2105 GPIO pins can be used as outputs.
Hardware donated by: Silicon Labs
MFC after: 3 weeks
tree is used to maintain the object's collection of resident pages,
vm_page_lookup() no longer needs an exclusive lock.
Reviewed by: attilio
Sponsored by: EMC / Isilon Storage Division
doesn't match the actual hardware queue this frame is queued to.
I'm trying to ensure that the holding buffers are actually being queued
to the same TX queue as the holding buffer that they end up on.
I'm pretty sure this is all correct so if this complains, it'll be due
to some kind of subtle broken-ness that needs fixing.
This is only done for legacy hardware, not EDMA hardware.
Tested:
* AR5416 STA mode, very lightly
PS-POLL support.
This implements PS-POLL awareness i nthe
* Implement frame "leaking", which allows for a software queue
to be scheduled even though it's asleep
* Track whether a frame has been leaked or not
* Leak out a single non-AMPDU frame when transmitting aggregates
* Queue BAR frames if the node is asleep
* Direct-dispatch the rest of control and management frames.
This allows for things like re-association to occur (which involves
sending probe req/resp as well as assoc request/response) when
the node is asleep and then tries reassociating.
* Limit how many frames can set in the software node queue whilst
the node is asleep. net80211 is already buffering frames for us
so this is mostly just paranoia.
* Add a PS-POLL method which leaks out a frame if there's something
in the software queue, else it calls net80211's ps-poll routine.
Since the ath PS-POLL routine marks the node as having a single frame
to leak, either a software queued frame would leak, OR the next queued
frame would leak. The next queued frame could be something from the
net80211 power save queue, OR it could be a NULL frame from net80211.
TODO:
* Don't transmit further BAR frames (eg via a timeout) if the node is
currently asleep. Otherwise we may end up exhausting management frames
due to the lots of queued BAR frames.
I may just undo this bit later on and direct-dispatch BAR frames
even if the node is asleep.
* It would be nice to burst out a single A-MPDU frame if both ends
support this. I may end adding a FreeBSD IE soon to negotiate
this power save behaviour.
* I should make STAs timeout of power save mode if they've been in power
save for more than a handful of seconds. This way cards that get
"stuck" in power save mode don't stay there for the "inactivity" timeout
in net80211.
* Move the queue depth check into the driver layer (ath_start / ath_transmit)
rather than doing it in the TX path.
* There could be some naughty corner cases with ps-poll leaking.
Specifically, if net80211 generates a NULL data frame whilst another
transmitter sends a normal data frame out net80211 output / transmit,
we need to ensure that the NULL data frame goes out first.
This is one of those things that should occur inside the VAP/ic TX lock.
Grr, more investigations to do..
Tested:
* STA: AR5416, AR9280
* AP: AR5416, AR9280, AR9160
QLogic 8300 Series Adapters
Submitted by: David C Somayajulu (davidcs@freebsd.org) QLogic Corporation
Approved by: George Neville-Neil (gnn@freebsd.org)
PV entries are now roughly half the size.
Instead of using a shared UMA zone for 28 byte pv entries
(two 8-byte tailq nodes, a 4 byte pointer, a 4 byte address and 4 byte
flags), we allocate a page at a time per process.
This provides 252 pv entries per process (actually, per pmap address space)
and eliminates one of the 8-byte tailq entries since we now can track
per-process pv entries implicitly.
The pointer to the pmap can be eliminated by doing address arithmetic to
find the metadata on the page headers to find a single pointer shared by
all 252 entries. There is an 8-int bitmap for the freelist of those 252
entries.
When in serious low memory condition, allocation of another pv_chunk is
possible by freeing some pages in pmap_pv_reclaim().
Added pv_entry/pv_chunk related statistics to pmap.
pv_entry/pv_chunk statistics can be accessed via sysctl vm.pmap.
Ported PTE freelist of KVA allocation and maintenance from i386.
Using an idea from Stephan Uphoff, use the empty pte's that correspond
to the unused kva in the pv memory block to thread a freelist through.
This allows us to free pages that used to be used for pv entry chunks
since we can now track holes in the kva memory block.
As both ARM pmap.c and pmap-v6.c use the same header and pv_entry, pmap and
md_page structures are different, it was needed to separate code designed
for ARMv6/7 from the one for other ARMs.
Submitted by: Zbigniew Bodek <zbb@semihalf.com>
Reviewed by: alc
Sponsored by: The FreeBSD Foundation, Semihalf
Instead of doing all sorts of weird casting of constants to
pointer-pointers, simply use the standard C offsetof() macro to obtain
the offset of the respective fields in the structures.
Instead of only checking the __STDC_VERSION__, we can also use Clang's
__has_extension() to check for features specifically. This allows us to,
say, use Clang's native _Static_assert() instead of the typedef hack,
making the compiler error messages a lot more readable.
Reviewed by: theraven
* Move the node sleep/wake state under the TX lock rather than the
node lock. Let's leave the node lock protecting rate control only
for now.
* When reassociating, various state needs to be cleared. For example,
the aggregate session needs to be torn down, including any pending
aggregation negotiation and BAR TX waiting.
* .. and we need to do a "cleanup" pass since frames in the hardware
TX queue need to be transmitted.
Modify ath_tx_tid_cleanup() to be called with the TX lock held and push
frames into a completion list. This allows for the cleanup to be
done atomically for all TIDs in a node rather than grabbing and
releasing the TX lock each time.
freelist.
o Split the pool of free pages queues really by domain and not rely on
definition of VM_RAW_NFREELIST.
o For MAXMEMDOM > 1, wrap the RR allocation logic into a specific
function that is called when calculating the allocation domain.
The RR counter is kept, currently, per-thread.
In the future it is expected that such function evolves in a real
policy decision referee, based on specific informations retrieved by
per-thread and per-vm_object attributes.
o Add the concept of "probed domains" under the form of vm_ndomains.
It is responsibility for every architecture willing to support multiple
memory domains to correctly probe vm_ndomains along with mem_affinity
segments attributes. Those two values are supposed to remain always
consistent.
Please also note that vm_ndomains and td_dom_rr_idx are both int
because segments already store domains as int. Ideally u_int would
have much more sense. Probabilly this should be cleaned up in the
future.
o Apply RR domain selection also to vm_phys_zero_pages_idle().
Sponsored by: EMC / Isilon storage division
Partly obtained from: jeff
Reviewed by: alc
Tested by: jeff
bit available for a flag in the pointer. However, it felt more correct
to enforce natural alignment of the key pointer. Unfortunately on
32bit architectures 64bit integers are not always naturally aligned.
Change the assert to enforce only 32bit alignment of the 64bit key for
now to fix the build. A more correct fix would be to properly sort
the struct buf fields which definitely suffer from bloat due to padding.
vm_page_insert() so that (1) vm_radix_lookup_le() is never called while the
free page queues lock is held and (2) vm_radix_lookup_le() is called at most
once. This change reduces the average time that the free page queues lock
is held by vm_page_alloc() as well as vm_page_alloc()'s average overall
running time.
Sponsored by: EMC / Isilon Storage Division
users to guarantee that the output of DTrace scripts will be time-ordered.
This option is enabled by adding the line
#pragma D option temporal
to the beginning of a script, or by adding '-x temporal' to the arguments of
dtrace(1).
This change fixes a bug in the original port of the temporal option. This
bug was causing some assertions to fail, so they had been disabled; in this
revision the assertions are working properly and are enabled.
The DTrace version number has been bumped from 1.9.0 to 1.9.1 to reflect
the language change that's being introduced.
This change corresponds to part of illumos-gate commit e5803b76927480:
3021 option for time-ordered output from dtrace(1M)
Reviewed by: pfg
Obtained from: illumos
MFC after: 1 month
with any structure containing a uint64_t index. The tree code
auto-generates type safe wrappers.
- Eliminate the buf splay and replace it with pctrie. This is not only
significantly faster with large files but also allows for the possibility
of shared locking.
Reviewed by: alc, attilio
Sponsored by: EMC / Isilon Storage Division
EABI ARM kernels or clang-compiled ARM kernels.
This fixes a crash seen in clang-compiled ARM
kernels that include WITNESS.
This code could be easily modified to walk the stack
for current clang-generated code (including EABI)
but Andrew Turner has raised concerns that the
stack frame currently emitted by clang isn't actually
required by EABI so such a change might cause problems
down the road.
In case anyone wants to experiment, the change
to support current clang-compiled kernels
involves simply setting FR_RFP=0 and FR_SCP=1.
functions, reverse the numbering scheme for the levels. The highest
numbered level in the tree now appears near the root instead of the leaves.
Sponsored by: EMC / Isilon Storage Division
With "cached read" HDD testing and multiple ports busy on a SATA
host controller, 3726/3826 PMP will very rarely drop a deferred
R_OK that was intended for the host. Symptom will be all 5 drives
under test will timeout, get reset, and recover.
Submitted by: Rich Futyma <rich.futyma@sanmina.com>
MFC after: 2 weeks
null_hashget() obtains the reference on the nullfs vnode, which must
be dropped.
- Fix a wart which existed from the introduction of the nullfs
caching, do not unlock lower vnode in the nullfs_reclaim_lowervp().
It should be innocent, but now it is also formally safe. Inform the
nullfs_reclaim() about this using the NULLV_NOUNLOCK flag set on
nullfs inode.
- Add a callback to the upper filesystems for the lower vnode
unlinking. When inactivating a nullfs vnode, check if the lower
vnode was unlinked, indicated by nullfs flag NULLV_DROP or VV_NOSYNC
on the lower vnode, and reclaim upper vnode if so. This allows
nullfs to purge cached vnodes for the unlinked lower vnode, avoiding
excessive caching.
Reported by: G??ran L??wkrantz <goran.lowkrantz@ismobile.com>
Tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
a non-loss reset.
When the drain functions are called, the holding descriptor and link pointers
are NULLed out.
But when the processq function is called during a non-loss reset, this
doesn't occur. So the next time a DMA occurs, it's chained to a descriptor
that no longer exists and the hardware gets angry.
Tested:
* AR5416, STA mode; use sysctl dev.ath.X.forcebstuck=1 to force a non-loss
reset.
TODO:
* Further AR9380 testing just to check that the behaviour for the EDMA
chips is sane.
PR: kern/178477
before using said node.
The "blessed" way here is to take a node reference before referencing
anything inside the node, otherwise the node can be freed between
the time the pointer is copied/dereferenced and the time the node contents
are used.
This mirrors fixes that I've done elsewhere in the net80211/driver
stack.
PR: kern/178470
the beaglebone-specific .dts file.
Add a new .dts for the BeagleBone Black with more memory,
slightly different pinmux initialization, and with mmchs1
configured (though the latter doesn't quite work yet).
options OCTEON_VENDOR_GEFES to enable support for these boards, to
match changes that GE publishes to the Octeon Simple Executive. Since
board types overlap with other boards, it is unlikely that we will
properly boot on other Octeon boards with OCTEON_VENDOR_GEFES enabled.
Tested extensively on the WANIC 6354, but I retained support for all
the other models. Some features need changes in the base kernel, and
those are in progress.
An array-type stat in vmm.ko is defined as follows:
VMM_STAT_ARRAY(IPIS_SENT, VM_MAXCPU, "ipis sent to vcpu");
It is incremented as follows:
vmm_stat_array_incr(vm, vcpuid, IPIS_SENT, array_index, 1);
And output of 'bhyvectl --get-stats' looks like:
ipis sent to vcpu[0] 3114
ipis sent to vcpu[1] 0
Reviewed by: grehan
Obtained from: NetApp
the Linux tree that they always include this chip in their FDT, so
make support for the ds1337 opt-out rather than opt-in. Now my boards
boot with the correct time.
Convert the structures to C99 style initialisation, which makes it
a lot easier to check that all of them are set and to generate a
derived template from them.
Sponsored by: DARPA, AFRL
MFC after: 2 weeks
assigned conflicting ranges to BARs then leaving the BARs alone could
result in one device stealing mmio accesses intended to go to a second
device. Prior to 233677 the PCI bus driver attempted to handle this case
by clearing the BAR to 0 depending on BARs based at 0 not decoding (which
is not guaranteed to be true). Now when a conflicting BAR is detected the
following steps are taken:
1) If hw.pci.realloc_bars (a new tunable) is enabled (default is enabled),
then ignore the current BAR setting from the firmware and attempt to
allocate a fresh resource range for the BAR.
2) If 1) failed (or was disabled), disable decoding for the relevant
BAR type (e.g. disable mem decoding for a memory BAR) and emit a
warning if booting verbose.
Tested by: Alex Keda <admin@lissyara.su>
MFC after: 1 week
to 63 bit positions.
Do not fill the save area and do not set the saved bit in the xstate
bit vector for the state which is not marked as enabled in xsave_mask.
Reported and tested by: Jim Ohlstein <jim@ohlste.in>
MFC after: 3 days
irrespective of the setting of lem_rx_process_limit, while
giving a chance to the taskqueue scheduler to act after
each chunk.
This makes lem_rxeof similar to the one in if_em.c and if_igb.c .
if_lem.c and if_em.c: add a sysctl to manually configure the
'itr' moderation register.
Approved by: Jack Vogel
locks. To support this, VNODE locks are created with the LK_IS_VNODE
flag. This flag is propagated down using the LO_IS_VNODE flag.
Note that WITNESS still records the LOR. Only the printing and the
optional entering into the kernel debugger is bypassed with the
WITNESS_NO_VNODE option.
all requested data was sent. The reason is that xfsize <= 0 condition
must not be tested at all if space == loopbytes. Otherwise, the done
is set to 1, and sendfile(2) is aborted too early.
Instead of moving the condition to exiting the inner loop after the
xfersize check, directly check for the completed transfer before the
testing of the available space in the socket buffer, and revert item 1
of r248830. It is arguably another bug to sleep waiting for socket
buffer space (or return EAGAIN for non-blocking socket) if all bytes
are already transferred.
Reported by: pho
Discussed with: scottl, gibbs
Tested by: scottl (stable/9 backport), pho
redefine such operations for different consumers.
This will be used when NUMA support will be finished and numaset
will need to be used.
Sponsored by: EMC / Isilon storage division
Obtained from: jeff
Reviewed by: alc
of "right".)
Flip back on the "always continue TX DMA using the holding descriptor"
code - by always setting ATH_BUF_BUSY and never setting axq_link to NULL.
Since the holding descriptor is accessed via txq->axq_link and _that_
is done behind the TXQ lock rather than the TX path lock, the holding
descriptor stuff itself needs to be behind the TXQ lock.
So, do the mental gymnastics needed to do this.
I've not seen any of the hardware failures that I was seeing when
I last tried to do this.
Tested:
* AR5416, STA mode
Until an ADM6996 driver shows up, this allows for the two switch
ports to be used.
Submitted by: Luiz Otavio O Souza <loos.br@gmail.com>
Reviewed by: ray
* Fix API changes;
* remove unused code;
* Allow some switches to be used that don't expose a set of PHY
registers for the CPU facing port (eg the ADM6996 for the Ubiquiti
Routerstation.)
Submitted by: Luiz Otavio O Souza <loos.br@gmail.com>
Reviewed by: ray
This adds a vlan capability field to etherswitch_info structure and some
definitions of ports flags.
It adds the support to global config parameters which right now is used
only to switch between the vlan modes, but it is intended to be extended
to support the setup of others parameters (STP, mirror, etc.).
Submitted by: Luiz Otavio O Souza <loos.br@gmail.com>
Reviewed by: ray
Use if_initbaudrate() to set baudrate.
Add IFCAP_LINKSTATE to if_capabilities.
Submitted by: David C Somayajulu <davidcs@freebsd.org>
Approved by: George Neville-Neil <gnn@freebsd.org>
do drain (flush_workqueue() in Linux terms) but instead returns true if
the work was removed before it is run, or false otherwise.
Simulate this by removing the taskqueue_drain() and return the value
derived from taskqueue_cancel()'s return value.
This would solve a witness warning caused by calling taskqueue_drain()
with a non-sleepable lock held, like:
taskqueue_drain with the following non-sleepable locks held:
exclusive rw lle (lle) r = 0 (0xfffffe001450b410) locked @
/usr/src/sys/netinet/in.c:1484
KDB: stack backtrace:
db_trace_self_wrapper() at db_trace_self_wrapper+0x2b/frame 0xffffff848d4f7690
kdb_backtrace() at kdb_backtrace+0x39/frame 0xffffff848d4f7740
witness_warn() at witness_warn+0x4a8/frame 0xffffff848d4f7800
taskqueue_drain() at taskqueue_drain+0x3a/frame 0xffffff848d4f7840
set_timeout() at set_timeout+0x4a/frame 0xffffff848d4f7860
netevent_callback() at netevent_callback+0x16/frame 0xffffff848d4f7870
arpintr() at arpintr+0x9b5/frame 0xffffff848d4f7930
This do not affect kernel without OFED compiled in.
Reported by: Garrett Cooper <yaneurabeya gmail com>
(who also tested an earlier version of this patch,
but bugs are mine)
MFC after: 2 weeks
I'm not sure why this is failing. The holding descriptor should be being
re-read when starting DMA of the next frame. Obviously something here
isn't totally correct.
I'll review the TX queue handling and see if I can figure out why this
is failing. I'll then re-revert this patch out and use the holding
descriptor again.
2. Added Flash Read/Update Support
3. Fixed TSO Handling
Submitted by: David C Somayajulu (davidcs@freebsd.org)
Reviewed by: George Neville-Neil (gnn@freebsd.org)
Approved by: George Neville-Neil (gnn@freebsd.org)
and printing at boot.
For reference on table informations and purposes please review ACPI specs.
Sponsored by: EMC / Isilon storage division
Obtained from: jeff
Reviewed by: jhb (earlier version)
order to match the MAXCPU concept. The change should also be useful
for consolidation and consistency.
Sponsored by: EMC / Isilon storage division
Obtained from: jeff
Reviewed by: alc
defaults to 1, meaning that it's off.
When read-ahead is enabled on a file, the vfs cluster code deliberately
breaks a read into 2 I/O transactions; one to satisfy the actual read,
and one to perform read-ahead. This makes sense in low-latency
circumstances, but often produces unbalanced i/o transactions that
penalize disks. By setting vfs.read_min, we can tell the algorithm to
fetch a larger transaction that what we asked for, achieving the same
effect as the read-ahead but without the doubled, unbalanced transaction
and the slightly lower latency. This significantly helps our workloads
with video streaming.
Submitted by: emax
Reviewed by: kib
Obtained from: Netflix
but partly to just tidy up things.
The problem here - there are too many TX buffers in the queue! By the
time one needs to transmit an EAPOL frame (for this PR, it's the response
to the group rekey notification from the AP) there are no ath_buf entries
free and the EAPOL frame doesn't go out.
Now, the problem!
* Enforcing the TX buffer limitation _before_ we dequeue the frame?
Bad idea. Because..
* .. it means I can't check whether the mbuf has M_EAPOL set.
The solution(s):
* De-queue the frame first
* Don't bother doing the TX buffer minimum free check until after
we know whether it's an EAPOL frame or not.
* If it's an EAPOL frame, allocate the buffer from the mgmt pool
rather than the default pool.
Whilst I'm here:
* Add a tweak to limit how many buffers a single node can acquire.
* Don't enforce that for EAPOL frames.
* .. set that to default to 1/4 of the available buffers, or 32,
whichever is more sane.
This doesn't fix issues due to a sleeping node or a very poor performing
node; but this doesn't make it worse.
Tested:
* AR5416 STA, TX'ing 100+ mbit UDP to an AP, but only 50mbit being received
(thus the TX queue fills up.)
* .. with CCMP / WPA2 encryption configured
* .. and the group rekey time set to 10 seconds, just to elicit the
behaviour very quickly.
PR: kern/138379
the page. This both reduces the number of queues locking and avoids
moving the active page to inactive list just because the page was read
or written.
Based on the suggestion by: alc
Reviewed by: alc
Tested by: pho
Keep following access permissions:
APX AP Kernel User
1 01 R N
1 10 R R
0 01 R/W N
0 11 R/W R/W
Avoid using reserved in ARMv6 APX|AP settings:
- In case of unprivileged (user) access without permission to write,
the access permission bits were being set to reserved for ARMv6
(but valid for ARMv7) value of APX|AP = 111.
Fix-up faulting userland accesses properly:
- Wrong condition statement in pmap_fault_fixup() caused that
any genuine, unprivileged access was being fixed-up instead of
just skip doing anything and return. Staring from now we ensure
proper reaction for illicit user accesses.
L2_S_PROT_R and L2_S_PROT_U names might be misleading as they do not
reflect real permission levels. It will be clarified in following
patches (switch to AP[2:1] permissions model).
Obtained from: Semihalf
- On ARMADAXP B0 (GP development board) we are not able to use PCI due to
whole 32-bit address space used by 4GB of RAM memory.
- Change is required to destroy unnecessary window to free address space
for PCI and other devices
- Fix offset value for SDRAM decoding windows
Obtained from: Semihalf
to driver specific files.
- window initialization is done during device attach
- CESA TDMA decoding windows values are set based on DTS,
not copied from CPU registers
- remove unnecessary virtual mapping
- update dts file
Obtained from: Semihalf
- Allow DMA addresses anywhere in the lower 4GB; Envy24HT has a 32-bit DMA
engine, not 28-bit like Envy24.
- Mark interrupt handler as MPSAFE, seems to be correctly synchronized.
PR: kern/152378
Submitted by: Jason Harmening <jason.harmening@gmail.com>
MFC after: 1 month
used previously caused probe failure on platforms where char is unsigned
(e.g. ARM), as mftrecsz can be negative.
Submitted by: Ilya Bakulin <ilya@bakulin.de>
MFC after: 2 weeks
change the way that these functions ascend the tree when the search for a
matching leaf fails at an interior node. Rather than returning to the root
of the tree and repeating the lookup with an updated key, maintain a stack
of interior nodes that were visited during the descent and use that stack
to resume the lookup at the closest ancestor that might have a matching
descendant.
Sponsored by: EMC / Isilon Storage Division
Reviewed by: attilio
Tested by: pho
fork_trampoline (thread entry point) assembler routines, because it's
not possible to unwind beyond those points.
Also insert STOP_UNWINDING in the exception_exit routine, to prevent an
unwind-loop at that point. This is just a stopgap until we get around
to instrumenting all assembler functions with proper unwind metadata.
exit the loop until after printing info about the current frame. Also,
if executing the unwind function for a frame doesn't change the values of
any registers, log that and exit the loop rather than looping endlessly.
Address. Although KAME implementation used FF02:0:0:0:0:2::/96 based on
older versions of draft-ietf-ipngwg-icmp-name-lookup, it has been changed
in RFC 4620.
The kernel always joins the /104-prefixed address, and additionally does
/96-prefixed one only when net.inet6.icmp6.nodeinfo_oldmcprefix=1.
The default value of the sysctl is 1.
ping6(8) -N flag now uses /104-prefixed one. When this flag is specified
twice, it uses /96-prefixed one instead.
Reviewed by: ume
Based on work by: Thomas Scheffler
PR: conf/174957
MFC after: 2 weeks
to cdevpriv(9). This commit changes the semantic of mount_smbfs
in userland as well, which now passes file descriptor in order to
to mount a specific filesystem istance.
Reviewed by: attilio, ed
Tested by: martymac
just "when the queue is busy."
After talking with the MAC team, it turns out that the linked list
implementation sometimes will not accept a TxDP update and will
instead re-read the link pointer. So even if the hardware has
finished transmitting a chain and has hit EOL/VEOL, it may still
re-read the link pointer to begin transmitting again.
So, always set ATH_BUF_BUSY on the last buffer in the chain (to
mark the last descriptor as the holding descriptor) and never
blank the axq_link pointer.
Tested:
* AR5416, STA mode
TODO:
* much more thorough testing with the pre-11n NICs, just to verify
that they behave the same way.
* test TDMA on the 11n and non-11n hardware.
kernel-based POSIX semaphore descriptors to userland via procstat(1) and
fstat(1):
- Change sem file descriptors to track the pathname they are associated
with and add a ksem_info() method to copy the path out to a
caller-supplied buffer.
- Use the fo_stat() method of shared memory objects and ksem_info() to
export the path, mode, and value of a semaphore via struct kinfo_file.
- Add a struct semstat to the libprocstat(3) interface along with a
procstat_get_sem_info() to export the mode and value of a semaphore.
- Teach fstat about semaphores and to display their path, mode, and value.
MFC after: 2 weeks
it was being passed down to VOP_IOCTL() where it promptly resulted in
ENOTTY due to a missing else for the past 8 years. While here, use a
shared vnode lock while fetching the current file's size.
MFC after: 1 week
- vm_phys_alloc_freelist_pages() can be called by vm_page_alloc_freelist()
to allocate a page from a specific freelist. In the NUMA case it did not
properly map the public VM_FREELIST_* constants to the correct backing
freelists, nor did it try all NUMA domains for allocations from
VM_FREELIST_DEFAULT.
- vm_phys_alloc_pages() did not pin the thread and each call to
vm_phys_alloc_freelist_pages() fetched the current domain to choose
which freelist to use. If a thread migrated domains during the loop
in vm_phys_alloc_pages() it could skip one of the freelists. If the
other freelists were out of memory then it is possible that
vm_phys_alloc_pages() would fail to allocate a page even though pages
were available resulting in a panic in vm_page_alloc().
Reviewed by: alc
MFC after: 1 week
- remove DA_FLAG_SAW_MEDIA flag, almost opposite to DA_FLAG_PACK_INVALID,
using the last instead.
- allow opening device with no media present, reporting zero media size
and non-zero sector size, as geom/notes suggests. That allow to read
device attributes and potentially do other things, not related to media.
in reduced memory systems.
- Split allocation and freeing of the configuration descriptor into a separate
function, so that the configuration descriptor can be made fixed size
to save memory allocations. This applies for both device and host mode.
system crash which happen after successfull fsync() return, the data
is accessible. For msdosfs, this means that FAT entries for the file
must be written.
Since we do not track the FAT blocks containing entries for the
current file, just do a sloppy sync of the devvp vnode for the mount,
which buffers, among other things, contain FAT blocks.
Simultaneously, for deupdat():
- optimize by clearing the modified flags before short-circuiting a
return, if the mount is read-only;
- only ignore the rest of the function for denode with DE_MODIFIED
flag clear when the waitfor argument is false. The directory buffer
for the entry might be of delayed write;
- microoptimize by comparing the updated directory entry with the
current block content;
- try to cluster the write, fall back to bawrite() if low on
resources.
Based on the submission by: bde
MFC after: 2 weeks
insmntque() is called. The standard insmntque destructor resets the
vop vector to deadfs one, and calls vgone() on the vnode. As result,
v_object is kept unchanged, which triggers an assertion in the reclaim
code, on instmntque() failure. Also, in this case, OBJ_TMPFS flag on
the backed vm object is not cleared.
Provide the tmpfs insmntque() destructor which properly clears
OBJ_TMPFS flag and resets v_object.
Reported and tested by: pho
Sponsored by: The FreeBSD Foundation
versions than the one in base (dim@ mentioned he tried on 4.7.3 and 4.8.1)
do not whine about it, so, at some point this workaround will be reverted.
Reported by: ache
Discussed with: dim
to query ATA functionality via ATA Pass-Through (16) as this page is defined
as "must" for SATL devices, hence indicating that the device is at least
likely to support Pass-Through (16).
This eliminates errors produced by CTL when ATA Pass-Through (16) fails.
Switch ATA probe daerror call to SF_NO_PRINT to avoid errors printing out
for devices which return invalid errors.
Output details about supported and choosen delete method when verbose booted.
Reviewed by: mav
Approved by: pjd (mentor)
MFC after: 1 week
Ensure that delete_available is reset so re-probes after a media change,
to one with different delete characteristics, will result in the correct
methods being flagged as available.
Make all ccb state changes use a consistent flow:
* free()
* xpt_release_ccb()
* softc->state = <new state>
* xpt_schedule()
Reviewed by: mav
Approved by: pjd (mentor)
MFC after: 1 week
The initial version of this came from Sandvine but had "PROVIDED BY NETAPP,
INC" in the copyright text, presuambly because the license block was copied
from another file. Replace it with standard "AUTHOR AND CONTRIBUTORS" form.
Approvided by: grehan@
The QCA9565 is a 1x1 2.4GHz 11n chip with integrated on-chip bluetooth.
The AR9300 HAL already has support for this chip; it just wasn't
included in the probe/attach path.
Tested:
* This commit brought to you over a QCA9565 wifi connection from
FreeBSD.
* .. ie, basic STA, pings, no iperf or antenna diversity checking just yet.
The pipe2() function is similar to pipe() but allows setting FD_CLOEXEC and
O_NONBLOCK (on both sides) as part of the function.
If p points to two writable ints, pipe2(p, 0) is equivalent to pipe(p).
If the pointer is not valid, behaviour differs: pipe2() writes into the
array from the kernel like socketpair() does, while pipe() writes into the
array from an architecture-specific assembler wrapper.
Reviewed by: kan, kib
for the last mbuf of the list with an encrypted message. This patch replaces
the KASSERT() with code that handles this case.
Reported by: john.gemignani@isilon.com
Reviewed by: jhb
MFC after: 2 weeks
The accept4() function, compared to accept(), allows setting the new file
descriptor atomically close-on-exec and explicitly controlling the
non-blocking status on the new socket. (Note that the latter point means
that accept() is not equivalent to any form of accept4().)
The linuxulator's accept4 implementation leaves a race window where the new
file descriptor is not close-on-exec because it calls sys_accept(). This
implementation leaves no such race window (by using falloc() flags). The
linuxulator could be fixed and simplified by using the new code.
Like accept(), accept4() is async-signal-safe, a cancellation point and
permitted in capability mode.
fpu-owned context, and for pcb-saved one. More, the XSAVE could do
partial save, same as XSAVEOPT, so qualifier for the handler should be
use_xsave and not use_xsaveopt.
Since xsave_area_desc is now needed regardless of the XSAVEOPT use,
remove the write-only use_xsaveopt variable.
In collaboration with: jhb
MFC after: 1 week
XFEATURE_ENABLED_SSE bits set is not needed. CPU correctly handles
any bitmask which is subset of the enabled bits in %XCR0.
More, CPU instructions XSAVE and XSAVEOPT could write the mask without
e.g. XFEATURE_ENABLED_SSE, after the VZEROALL. The check prevents the
restoration of the otherwise valid FPU save area.
In collaboration with: jhb
MFC after: 1 week
Remove #define to get kludges that asm.h used to define
Move clever macros to access assembler instructions to trap.c
Remove __ASSEMBLER__ ifdefs in regdef.h: they aren't needed anymore.
expand the %sccs.include.redist.c% directive with the standard
3-clause license, and add $FreeBSD$ to keep the commit script happy.
# This may break some mips stuff, which will be fixed in the next commit.
Add a simplebus attachment for cfi(4)'s FDT support and move
cfi_bus_fdt.c to sys/conf/files so non-ppc architectures are supported.
Sponsored by: DARPA, AFRL
- netmap_rx_irq()/netmap_tx_irq() can now be called by FreeBSD drivers
hiding the logic for handling NIC interrupts in netmap mode.
This also simplifies the case of NICs attached to VALE switches.
Individual drivers will be updated with separate commits.
- use the same refcount() API for FreeBSD and linux
- plus some comments, typos and formatting fixes
Portions contributed by Michio Honda
those of some non-architectural core events. This is not a problem in the
general case as long as there's an 1:1 mapping between the two, but there
are few exceptions. For example, 3CH_01H on Nehalem/Westmere represents
both unhalted-reference-cycles and CPU_CLK_UNHALTED.REF_P.
CPU_CLK_UNHALTED.REF_P on the aforementioned architectures does not measure
reference (i.e. bus) but TSC, so there's the need to disambiguate.
In order to avoid the namespace collision rename all the architectural
events in a way they cannot be ambigous and refactor the architectural
events handling function to reflect this change.
While here, per Jim Harris request, rename
iap_architectural_event_is_unsupported() to iap_event_is_architectural().
Discussed with: jimharris
Reviewed by: jimharris, gnn
A blocking accept (and some other operations) waits on &so->so_timeo. Once
it wakes up, it will detect the SBS_CANTRCVMORE bit.
The error from accept() is [ECONNABORTED] which is not the nicest one -- the
thread calling accept() needs to know out-of-band what is happening.
A spurious wakeup on so->so_timeo appears harmless (sleep retried) except
when lingering on close (SO_LINGER, and in that case there is no descriptor
to call shutdown() on) so this should be fairly safe.
A shutdown() already woke up a blocked accept() for TCP sockets, but not for
Unix domain sockets. This fix is generic for all domains.
This patch was sent to -hackers@ and -net@ on April 5.
MFC after: 2 weeks
at least if FreeBSD is ran under VirtualBox. In order to avoid the leakage,
properly deallocate structures in case CPU claims that hw performance
monitoring counters are not supported.
Reported by: hiren
-DBKTR_NEW_MSP34XX_DRIVER and -Wformat-security.
This also allows to eliminates a superfluous malloc/snprintf/free on
intermediate buffer.
PR: kern/175546
MFC after: 1 week
The NTB allows you to connect two systems with this device using a PCI-e
link. The driver is made of two modules:
- ntb_hw which is a basic hardware abstraction layer for the device.
- if_ntb which implements the ntb network device and the communication
protocol.
The driver is limited at the moment to CPU memcpy instead of using DMA, and
only Back-to-Back mode is supported. Also the network device isn't full
featured yet. These changes will be coming soon. The DMA change will also
bring in the ioat driver from the project branch it is on now.
This is an initial port of the GPL/BSD Linux driver contributed by Jon Mason
from Intel. Any bugs are my contributions.
Sponsored by: Intel
Reviewed by: jimharris, joel (man page only)
Approved by: jimharris (mentor)
* That lock isn't actually held during reset - just the whole TX/RX path
is paused. So, remove the assertion.
* Log the TX queue status - how many hardware frames are active in the
MAC and whether the queue is active.
/home/sbruno/bsd/head/sys/dev/hptrr/hptrr_osm_bsd.c:178:66: warning: for loop has empty body [-Wempty-body]
for (order=0, size=PAGE_SIZE; size<f->size; order++, size<<=1) ;
^
/home/sbruno/bsd/head/sys/dev/hptrr/hptrr_osm_bsd.c:178:66: note: put the semicolon on a separate line to silence this warning
Obtained from: Yahoo! Inc.
MFC after: 2 weeks
vnode v_object to avoid double-buffering. Use the same object both as
the backing store for tmpfs node and as the v_object.
Besides reducing memory use up to 2x times for situation of mapping
files from tmpfs, it also makes tmpfs read and write operations copy
twice bytes less.
VM subsystem was already slightly adapted to tolerate OBJT_SWAP object
as v_object. Now the vm_object_deallocate() is modified to not
reinstantiate OBJ_ONEMAPPING flag and help the VFS to correctly handle
VV_TEXT flag on the last dereference of the tmpfs backing object.
Reviewed by: alc
Tested by: pho, bf
MFC after: 1 month
v_object of non OBJT_VNODE type.
For vm_object_page_clean(), simply do not assert that object type must
be OBJT_VNODE, and add a comment explaining how the check for
OBJ_MIGHTBEDIRTY prevents the rest of function from operating on such
objects.
For vm_mmap_vnode(), if the object type is not OBJT_VNODE, require it
to be for swap pager (or default), handle the bypass filesystems, and
correctly acquire the object reference in this case.
Reviewed by: alc
Tested by: pho, bf
MFC after: 1 week
