return events on the fixed handler even after defining a duplicate in the
AML. While this violates the spec, hopefully we can get by with leaving
both installed.
It works as follows:
In every 'interval' seconds defined links are checked.
If they are non-active they will not be used by to data transfer.
No response from: julian, archie
Silent on: net@
Approved by: scottl (mentor)
mode is applied, since tunneled packets are considered to be
generated packets from a tunnel encapsulating node.
- tunnel mode may not be applied if SA mode is ANY and policy
does not say "tunnel it". check if we have extra IPv6 header
on the packet after ipsec6_output_tunnel() and call ip6_output()
only if additional IPv6 header is added.
- free the copyed packet before returning.
Obtained from: KAME
It returns 1 is process is inside of jail and 0 if it is not.
Information if we are in jail or not is not a secret, there is plenty of
ways to discover it. Many people are using own hack to check this and
this will be a legal way from now on.
It will be great if our starting scripts will take advantage of this sysctl
to allow clean "boot" inside jail.
Approved by: rwatson, scottl (mentor)
has been executed. On return from the signal handler
the call will either be restarted or EINTR will be returned,
but it will not go back to its previous state. So, it is
sufficient to simply change the state to 'running' without
actually trying to wake up the thread.
to size_t *, which is incorrect because they may have different widths.
This caused some subtle forms of corruption, the mostly frequently
reported one being that the last character of a filename was sometimes
duplicated on amd64.
stopped returning events. Don't disable the event when removing
the handler because it still needs to be enabled for the other
handler. Also, remove duplicate AcpiEnableEvent calls since the
install function now does this for us.
into its own file:
- All of the $PIR interrupt routing is now done in a link-centric fashion.
When a host-PCI bridge that uses the $PIR attaches, it calls pir_parse()
to parse the table. This scans for link devices and merges all the masks
for each link device from the table entries. It then looks at the intline
register of PCI devices connected to a link to figure out if the BIOS has
routed this link and if so to which IRQ.
- The IRQ for any given link can be overridden via a hint like so:
'hw.pci.link.0x62.irq=10' Any IRQ set in this matter is treated as if it
were set that way by the BIOS.
- We only call the BIOS to route each link device once.
- When a PCI device wants to route an interrupt, we look it up in the $PIR
to find the associated link. If the link is routed, we simply return the
IRQ it is using. If it is not routed, we have to pick one. This uses a
different algorithm from the old code. First off, when we try to pick
an interrupt from a mask of possible interrupts, we try to pick the one
that is least loaded as far as PCI devices. We maintain this weight based
on the number of devices attached to each link device. When choosing an
IRQ, we first attempt to route using any PCI only interrupts (the old
code did this as well). If that doesn't work, we try to use the list of
IRQs that the BIOS has used. This is a new step that the new code didn't
do and avoids using IRQ 3 or 4 for every virgin interrupt routing. If
none of the IRQs that the BIOS used worked, then we fall back to trying
anything.
- The fallback mask for !PC98 was fixed to include IRQ 3 and not allow IRQ
2.
- We don't use the $PIR to route interrupts on a PCI-PCI bridge unless it
has already been used to route on at least one Host-PCI bridge. This
helps to avoid mixing and matching x86 firmware PCI interrupt routing
methods (which is a Bad Thing(tm)).
Silence on: current@
Use %ju and an (uintmax_t) cast to print size_t values.
Use %jd and an (intmax_t) cast to print off_t values.
Use off_t variables to hold the difference between two off_t values.
Don't bother with unsigned char where char will do nicely.
Previously the "struct disk" were owned by the device driver and this
gave us problems when the device disappared and the users of that device
were not immediately disappearing.
Now the struct disk is allocate with a new call, disk_alloc() and owned
by geom_disk and just abandonned by the device driver when disk_create()
is called.
Unfortunately, this results in a ton of "s/\./->/" changes to device
drivers.
Since I'm doing the sweep anyway, a couple of other API improvements
have been carried out at the same time:
The Giant awareness flag has been flipped from DISKFLAG_NOGIANT to
DISKFLAG_NEEDSGIANT
A version number have been added to disk_create() so that we can detect,
report and ignore binary drivers with old ABI in the future.
Manual page update to follow shortly.
a PTHREAD_RWLOCK_INITIALIZER to do for rwlocks what
a similarly named symbol does for statically initialized mutexes.
This symbol was dropped in The Open Group Base Specifications Issue 6
and does not exist in IEEE Std 1003.1, 2003, but it should still be
supported for backwards compatibility.
Pointy hat: mtm
o Instead of checking both the passed in pointer and its value
for NULL, only check the latter. Any caller that passes in
a NULL pointer is obviously wrong.
o Fix mutex priority protocols. Keep separate counts of priority
inheritance and protection mutexes to make things easier.
This will not have much affect since this is only the
userland side, and the rest involves kernel scheduling.
