tun(4) and tap(4) share the same general management interface and have a lot
in common. Bugs exist in tap(4) that have been fixed in tun(4), and
vice-versa. Let's reduce the maintenance requirements by merging them
together and using flags to differentiate between the three interface types
(tun, tap, vmnet).
This fixes a couple of tap(4)/vmnet(4) issues right out of the gate:
- tap devices may no longer be destroyed while they're open [0]
- VIMAGE issues already addressed in tun by kp
[0] emaste had removed an easy-panic-button in r240938 due to devdrn
blocking. A naive glance over this leads me to believe that this isn't quite
complete -- destroy_devl will only block while executing d_* functions, but
doesn't block the device from being destroyed while a process has it open.
The latter is the intent of the condvar in tun, so this is "fixed" (for
certain definitions of the word -- it wasn't really broken in tap, it just
wasn't quite ideal).
ifconfig(8) also grew the ability to map an interface name to a kld, so
that `ifconfig {tun,tap}0` can continue to autoload the correct module, and
`ifconfig vmnet0 create` will now autoload the correct module. This is a
low overhead addition.
(MFC commentary)
This may get MFC'd if many bugs in tun(4)/tap(4) are discovered after this,
and how critical they are. Changes after this are likely easily MFC'd
without taking this merge, but the merge will be easier.
I have no plans to do this MFC as of now.
Reviewed by: bcr (manpages), tuexen (testing, syzkaller/packetdrill)
Input also from: melifaro
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D20044
In the armv4/5 world device statements in these files were common, but in
the v6/7 world, other socs don't put device statements into those files, so
this just brings imx5 and imx6 into line with the current conventions.
This adds sys/modules/imx with a SUBDIR makefile to make the whole
collection of modules that are specific to these SoCs. Initially, that
"whole collection" consists of the if_ffec and imx_i2c drivers.
The if_ffec driver is referenced in its existing home in ../ffec rather
than moving it into the imx directory, because it's used by powerpc too,
but it is no longer built for all armv6/7 systems.
The imx_i2c driver is newly added as a module.
Transition all boards that support arm cortex CPUs to armv7. This
leaves two armv6 kernels in the tree. RPI-B, which uses the BCM2835
which has a ARM1176 core, and VERSATILEPB, which is a qemu board setup
around the time RPI-B went in. Copy std.armv6 to std.armv7, even
though that duplicates a lot of stuff. More work needs to be done to
sort out the duplication.
Differential Revision: https://reviews.freebsd.org/D12027
This was submitted by Rogiel Sulzbach (thank you!) but has a few last-minute
changes by me, mostly where the code interfaces to my still-utterly-deficient
imx6_ccm clocks implementation. So blame me for any mistakes.
Submitted by: Rogiel Sulzbach <rogiel@rogiel.com>
Differential Revision: https://reviews.freebsd.org/D11177
be migrated to this and will allow the removal of this option.
Reviewed by: ian
Sponsored by: ABT Systems Ltd
Differential Revision: https://reviews.freebsd.org/D9907
All armv6 processors are plenty fast enough for HZ=1000.
No changes are made for older arm systems, because some chips are a bit
wimpy for 1000 while others do fine, so it has to be set on a per-config
basis.
Current functionality is somewhat limited: driver assumes that there
is only one active IPU unit (IPU1) and that video output is DI0 and
video mode is 1024x768. For more advanced functionality driver requires
proper clock management which is work in progress. At the moment driver
assumes that pixel clock is configured by u-boot for 1026x768 mode.
Reviewed by: andrew, ian, mmel
Differential Revision: https://reviews.freebsd.org/D4168
interrupt controller.
The latter is required for INTRNG, because of the hardware erratum
workaround installed by the linux folks into the imx6 FDT data, which remaps
an ethernet interrupt to the gpio device. In the non-INTRNG world we
intercept the call to map the interrupt and map it back to the ethernet
hardware (because we don't need linux's workaround), but in the INTRNG world
we lose the hookpoint where that remapping was happening, but we gain the
ability to work the way linux does by having the gpio driver dispatch the
interrupt.
each of the existing kernel configs. This gives a place to put config
that applies to the entire arch.
Add the ARM_NEW_PMAP option to std.armv6. This is working well in early
testing and it's time for wide exposure, but it's still nice to be able
to fall back to the old implementation for testing when a problem comes
along. Eventually the option and the old implementation will go away.
The opportunity now exists to move a whole lot of boilerplate from all the
arm kernel config files into std.arm*, but that's a commit for another day.
have chosen different (and more traditional) stateless/statuful
NAT64 as translation mechanism. Last non-trivial commits to both
faith(4) and faithd(8) happened more than 12 years ago, so I assume
it is time to drop RFC3142 in FreeBSD.
No objections from: net@
enabled. Also switch IMX6 to use SCHED_ULE.
The now-unreferenced WANDBOARD.common config will be deleted after giving
folks who may be including it a heads-up to switch to IMX6.
WANDBOARD.common config, but with the freescale-specific optons and devices
all together at the bottom now. In addition to reformatting and shuffling
lines around, two new options are added because they're now known to work,
VFP and FREEBSD_BOOT_LOADER.
This config does not include any static DTB, it requires that u-boot
provide a DTB (or a custom kernel config can compile one in).
This will supercede all the existing WANDBOARD* configs, but those will
be left around for a while to help people transition their customized
configs to include this new one instead.
