the original amd64 and i386 headers with stubs.
Rename (AMD64|I386)_BUS_SPACE_* to X86_BUS_SPACE_* everywhere.
Reviewed by: imp (previous version), jhb
Approved by: kib (mentor)
controller with Card Read Host Controller. These controllers are
multi-function devices and have the same ethernet core of
JMC250/JMC260. Starting from REVFM 5(chip full mask revision)
controllers have the following features.
o eFuse support
o PCD(Packet Completion Deferring)
o More advanced PHY power saving
Because these controllers started to use eFuse, station address
modified by driver is permanent as if it was written to EEPROM. If
you have to change station address please save your controller
default address to safe place before reprogramming it. There is no
way to restore factory default station address.
Many thanks to JMicron for continuing to support FreeBSD.
HW donated by: JMicron
a 2GHz channel with appropriate flags set to sc->config. Due to not zeroing
sc->config for auth/assoc those flags are still set while trying to connect
on a 5GHz channel.
MFC after: 3 days
Use pci_enable_busmaster instead of setting PCIM_CMD_BUSMASTEREN
directly. There's no need to set PCIM_CMD_MEMEN. The bit is set when a
SYS_RES_MEMORY resource is activated.
Remove redundant pci_* function calls from suspend/resume methods. The
bus driver already saves and restores the PCI configuration.
Write 1 byte instead of 4 when setting the HIFN_TRDY_TIMEOUT register.
It is only 1 byte according to the specification.
Reviewed by: jhb
Approved by: kib (mentor)
configuration registers directly.
Remove pci_enable_io calls where they are redundant. The PCI bus driver
will set the right bits when the corresponding bus resource is activated.
Remove redundant pci_* function calls from suspend/resume methods. The
bus driver already saves and restores the PCI configuration.
Reviewed by: jhb
Approved by: kib (mentor)
This is based on the patch submitted by Yuri Skripachov.
Overview of the changes:
- clarify double-use of some ACPI_BATT_STAT_* definitions
- clean up undefined/extended status bits returned by _BST
- warn about charging+discharging bits being set at the same time
PR: kern/124744
Submitted by: Yuri Skripachov <y.skripachov@gmail.com>
Tested by: Yuri Skripachov <y.skripachov@gmail.com>
MFC after: 2 weeks
allow the child atkbd device to reuse that IRQ resource instead of
reallocating the same IRQ from the parent bus inside the atkbd driver.
- Don't allocate a shared IRQ for the atkbd driver. For AT keyboard
devices on an ISA bus the IRQ is not shareable. Instead, the bus driver
should mark the IRQ shareable if the bus supports shared IRQs.
- Don't identify child devices until after the atkbdc device itself has
attached.
delete the IRQ resource from the psmcpnp device completely.
- Don't allocate the IRQ resource shared. It is not a shareable interrupt
on ISA. The bus driver can set RF_SHAREABLE if the IRQ is actually
shareable on a non-ISA bus.
- Avoid side-effect assignments in if statements when possible.
- Don't use ! to check for NULL pointers, explicitly check against NULL.
- Explicitly check error return values against 0.
- Don't use INTR_MPSAFE for interrupt handlers with only filters as it is
meaningless.
- Remove unneeded function casts.
function always returned the nominal frequency instead of current frequency
because we use RDTSC instruction to calculate difference in CPU ticks, which
is supposedly constant for the case. Now we support cpu_get_nominal_mhz()
for the case, instead. Note it should be just enough for most usage cases
because cpu_est_clockrate() is often times abused to find maximum frequency
of the processor.
There is no need to use an atomic operation at structure initialization
time.
Note that the file changed is not connected to the build at this time.
Reviewed by: jhb (general issue)
Approved by: np
MFC after: 2 weeks
Prior to this change, the addressing method wasn't getting set, and
so the LUN field could be set incorrectly in some instances.
This fix should allow for LUN numbers up to 16777215 (and return an error
for anything larger, which wouldn't fit into the flat addressing model).
Submitted by: scottl (in part)
This bug manifested itself after repeated device arrivals and
departures. The root of the problem was that the last entry in the
reply array wasn't initialized/allocated. So every time we got
around to that event, we had a bogus address.
There were a couple more problems with the code that are also fixed:
- The reply mechanism was being treated as sequential (indexed by
sc->replycurindex) even though the spec says that the driver
should use the ReplyFrameAddress field of the post queue
descriptor to figure out where the reply is. There is no
guarantee that the reply descriptors will be used in sequential
order.
- The second word of the reply post queue descriptor wasn't being
checked in mps_intr_locked() to make sure that it wasn't
0xffffffff. So the driver could potentially come across a
partially DMAed descriptor.
- The number of replies allocated was one less than the actual
size of the queue. Instead, it was the size of the number of
replies that can be used at one time. (Which is one less than
the size of the queue.)
mps.c: When initializing the entries in the reply free
queue, make sure we initialize the full number that
we tell the chip we have (sc->fqdepth), not the
number that can be used at any one time (sc->num_replies).
When allocating replies, make sure we allocate the
number of replies that we've told the chip exist,
not just the number that can be used simultaneously.
Use the ReplyFrameAddress field of the post queue
descriptor to figure out which reply is being
referenced. This is what the spec says to do, and
the spec doesn't guarantee that the replies will be
used in order.
Put a check in to verify that the reply address passed
back from the card is valid. (Panic if it isn't, we'll
panic when we try to deference the reply pointer in any
case.)
In mps_intr_locked(), verify that the second word of the
post queue descriptor is not 0xffffffff in addition to
verifying that the unused flag is not set, so we can
make sure we didn't get a partially DMAed descriptor.
Remove references to sc->replycurindex, it isn't needed
now.
mpsvar.h: Remove replycurindex from the softc, it isn't needed now.
Reviewed by: scottl
functionality is the same, a difference is that the DS1775 has a better
precision than the LM75. But we do not use it in our setup. Make the
LM75 work the same as the DS1775.
Fix a typo in device_set_desc.
Tested by: Paul Mather <paul at gromit dlib vt edu>
Approved by: nwhitehorn (mentor)
pointer where data is to be returned by ibask() (currently unimplemented),
while __retval holds the value returned by the libgpib ibfoo() functions.
The confusion resulted in the ibfoo() functions returning an uninitialized
value except in situations where the GPIB activity has been terminated
abnormally.
MFC after: 3 days
re-arming the watchdog timeout.
Sponsored by: Sandvine Incorporated
Submitted by: Mark Johnston <mjohnston at sandvine dot com>
Reviewed by: des
MFC after: 10 days
AX88772 controllers. ASIX added a new feature for AX88178/AX88772
controllers which allows combining multiple TX frames into a single
big frame. This was to overcome one of USB limitation where it
can't generate more than 8k interrupts/sec which in turn means USB
ethernet controllers can not send more than 8k packets per second.
Using ASIX's feature greatly enhanced TX performance(more than 3~4
times) compared to 7.x driver. However it seems r184610 removed
boundary checking for buffered frames which in turn caused
instability issues under certain conditions. In addition, using
ASIX's feature triggered another issue which made USB controller
hang under certain conditions. Restarting ethernet controller
didn't help under this hang condition and unplugging and replugging
the controller was the only solution. I believe there is a silicon
bug in TX frame combining feature on AX88178/AX88772 controllers.
To address these issues, reintroduce the boundary checking for both
AX88178 and AX88772 after copying a frame to USB buffer and do not
use ASIX's multiple frame combining feature. Instead, use USB
controller's multi-frame transmit capability to enhance TX
performance as suggested by Hans[1].
This should fix a long standing axe(4) instability issues reported
on AX88772 and AX88178 controllers. While I'm here remove
unnecessary TX frame length check since upper stack always
guarantee the size of a frame to be less than MCLBYTES.
Special thanks to Derrick Brashear who tried numerous patches
during last 4 months and waited real fix with patience. Without
this enthusiastic support, patience and H/W donation I couldn't fix
it since I was not able to trigger the issue on my box.
Suggested by: hselasky [1]
Tested by: Derrick Brashear (shadow <> gmail dot com>
H/W donated by: Derrick Brashear (shadow <> gmail dot com>
PR: usb/140883
isn't configurable in a meaningful way. This is for ifconfig(8) or
other tools not to change code whenever IFT_USB-like interfaces are
registered at the interface list.
Reviewed by: brooks
No objections: gavin, jkim
looking to see if there is an existing IRQ resource for a given IRQ
provided by the BIOS and using that RID if so. Otherwise, allocate a new
RID for the new IRQ.
Reviewed by: mav (a while ago)
max_request_segments * PAGE_SIZE if the I/O is page-aligned; the
largest I/O we can guarantee will work is PAGE_SIZE less than that.
This unbreaks 'diskinfo -t'.
as an association ID is set any scan is supposed to be a background scan.
This implies that the firmware will switch back to the associated channel
after a certain threshold, though, we are not notified about that. We
currently catch this case by a timer which will reset the firmware after
a 'scan timeout', though, upper layers are not notified about that and
will simply hang until manual intervention. Fix this by resetting the
firmware's knowledge about any association on RUN -> ASSOC and
!INIT -> SCAN transitions.
Tested by: Zhihao Yuan <lichray at gmail.com>
MFC after: 1 week
- Do not call iwn_calib_reset() for monitor mode. We do not want to query
information and do runtime calibration while in monitor mode. Poking the
firmware with adjustments for calibration results in firmware asserts.
This could happened on RUN -> RUN transition only.
- Adjust blink rate for monitor mode. It's supposed to not freak out and
turn off after a while.
- While here, remove one useless assignment of calib.state, it gets
overwritten later in the function.
Submitted by: Brandon Gooch <jamesbrandongooch at gmail.com>
MFC after: 1 week
preserve the upper bits of the first data byte.
While here, shorten a few nearby lines.
PR: kern/152768
Reported by: Sascha Wildner saw of online.de
Reviewed by: scottl
MFC after: 1 week
longer requested of the boot firmware. Instead of sending those results
to the runtime firmware the firmware is told to do the DC calibration
itself.
MFC after: 1 week
the size can be smaller than the constant when you are
doing HW TAGGING, and you still need to process this
packet in a normal way. I'm not sure where the notion
to just return came from, but its wrong.
MFC after: 3 days
Second, correct the discard/refresh_mbufs code to behave
more like igb, there have been panics due to discards and
this should fix them.
MFC after: 3 days
finding. The test to compare the mbuf m_len against
a fixed value and then returning needs to be removed.
When using VLANS and doing HW_TAGGING, and IPV6, the
ICMP6 packets actually fail this condition, the constant
assumes that the tag is IN the frame, and its not, so
the length is actually tiny. Furthermore, I'm not sure
what the point was to just return??
MFC after: 3 days
the controller to workaround silicon bug of i82557. Each reset will
re-establish link which in turn triggers MII status change
callback. The callback will try to reconfigure controller if the
controller is not i82557 to enable flow-control. This caused
endless link UP/DOWN when the workaround was enabled on non-i82557
controller.
To fix the issue, apply RX lockup workaround only for i82557.
Previously it blindly checked undocumented EEPROM location such
that it sometimes enabled the workaround for other controllers. At
this time, only i82557 is known to have the silicon bug.
This fixes a regression introduced in r215906 which enabled flow
control support for all controllers except i82557.
Reported by: Karl Denninger (karl <> denninger dot net)
Tested by: Karl Denninger (karl <> denninger dot net)
MFC after: 3 days
or detached. Normally it should be changed through user land ioctl(2)
system calls but it looks there's no apps for USB and no need.
With this patch, libpcap would detect the usbus interfaces correctly and
tcpdump(1) could dump the USB packets into PCAP format with -w option.
However it couldn't print the output to console because there's no
printer-routine at tcpdump(1).
This includes support in the kernel, camcontrol(8), libcam and the mps(4)
driver for SMP passthrough.
The CAM SCSI probe code has been modified to fetch Inquiry VPD page 0x00
to determine supported pages, and will now fetch page 0x83 in addition to
page 0x80 if supported.
Add two new CAM CCBs, XPT_SMP_IO, and XPT_GDEV_ADVINFO. The SMP CCB is
intended for SMP requests and responses. The ADVINFO is currently used to
fetch cached VPD page 0x83 data from the transport layer, but is intended
to be extensible to fetch other types of device-specific data.
SMP-only devices are not currently represented in the CAM topology, and so
the current semantics are that the SIM will route SMP CCBs to either the
addressed device, if it contains an SMP target, or its parent, if it
contains an SMP target. (This is noted in cam_ccb.h, since it will change
later once we have the ability to have SMP-only devices in CAM's topology.)
smp_all.c,
smp_all.h: New helper routines for SMP. This includes
SMP request building routines, response parsing
routines, error decoding routines, and structure
definitions for a number of SMP commands.
libcam/Makefile: Add smp_all.c to libcam, so that SMP functionality
is available to userland applications.
camcontrol.8,
camcontrol.c: Add smp passthrough support to camcontrol. Several
new subcommands are now available:
'smpcmd' functions much like 'cmd', except that it
allows the user to send generic SMP commands.
'smprg' sends the SMP report general command, and
displays the decoded output. It will automatically
fetch extended output if it is available.
'smppc' sends the SMP phy control command, with any
number of potential options. Among other things,
this allows the user to reset a phy on a SAS
expander, or disable a phy on an expander.
'smpmaninfo' sends the SMP report manufacturer
information and displays the decoded output.
'smpphylist' displays a list of phys on an
expander, and the CAM devices attached to those
phys, if any.
cam.h,
cam.c: Add a status value for SMP errors
(CAM_SMP_STATUS_ERROR).
Add a missing description for CAM_SCSI_IT_NEXUS_LOST.
Add support for SMP commands to cam_error_string().
cam_ccb.h: Rename the CAM_DIR_RESV flag to CAM_DIR_BOTH. SMP
commands are by nature bi-directional, and we may
need to support bi-directional SCSI commands later.
Add the XPT_SMP_IO CCB. Since SMP commands are
bi-directional, there are pointers for both the
request and response.
Add a fill routine for SMP CCBs.
Add the XPT_GDEV_ADVINFO CCB. This is currently
used to fetch cached page 0x83 data from the
transport later, but is extensible to fetch many
other types of data.
cam_periph.c: Add support in cam_periph_mapmem() for XPT_SMP_IO
and XPT_GDEV_ADVINFO CCBs.
cam_xpt.c: Add support for executing XPT_SMP_IO CCBs.
cam_xpt_internal.h: Add fields for VPD pages 0x00 and 0x83 in struct
cam_ed.
scsi_all.c: Add scsi_get_sas_addr(), a function that parses
VPD page 0x83 data and pulls out a SAS address.
scsi_all.h: Add VPD page 0x00 and 0x83 structures, and a
prototype for scsi_get_sas_addr().
scsi_pass.c: Add support for mapping buffers in XPT_SMP_IO and
XPT_GDEV_ADVINFO CCBs.
scsi_xpt.c: In the SCSI probe code, first ask the device for
VPD page 0x00. If any VPD pages are supported,
that page is required to be implemented. Based on
the response, we may probe for the serial number
(page 0x80) or device id (page 0x83).
Add support for the XPT_GDEV_ADVINFO CCB.
sys/conf/files: Add smp_all.c.
mps.c: Add support for passing in a uio in mps_map_command(),
so we can map a S/G list at once.
Add support for SMP passthrough commands in
mps_data_cb(). SMP is a special case, because the
first buffer in the S/G list is outbound and the
second buffer is inbound.
Add support for warning the user if the busdma code
comes back with more buffers than will work for the
command. This will, for example, help the user
determine why an SMP command failed if busdma comes
back with three buffers.
mps_pci.c: Add sys/uio.h.
mps_sas.c: Add the SAS address and the parent handle to the
list of fields we pull from device page 0 and cache
in struct mpssas_target. These are needed for SMP
passthrough.
Add support for the XPT_SMP_IO CCB. For now, this
CCB is routed to the addressed device if it supports
SMP, or to its parent if it does not and the parent
does. This is necessary because CAM does not
currently support SMP-only nodes in the topology.
Make SMP passthrough support conditional on
__FreeBSD_version >= 900026. This will make it
easier to MFC this change to the driver without
MFCing the CAM changes as well.
mps_user.c: Un-staticize mpi_init_sge() so we can use it for
the SMP passthrough code.
mpsvar.h: Add a uio and iovecs into struct mps_command for
SMP passthrough commands.
Add a cm_max_segs field to struct mps_command so
that we can warn the user if busdma comes back with
too many segments.
Clear the cm_reply when a command gets freed. If
it is not cleared, reply frames will eventually get
freed into the pool multiple times and corrupt the
pool. (This fix is from scottl.)
Add a prototype for mpi_init_sge().
sys/param.h: Bump __FreeBSD_version to 900026 for the for the
inclusion of the XPT_GDEV_ADVINFO and XPT_SMP_IO
CAM CCBs.
versions of FreeBSD. In fact we are already missing a lot of conditional
code necessary to support older versions of FreeBSD, including alternatives
for vital functionality not yet provided by the respective subsystem back
then (see for example r199663). So this change shouldn't actually break
this driver on versions of FreeBSD that were supported before. Besides,
this driver also isn't maintained as an multi-release version outside of
the main repository, so removing the conditional code shouldn't be a
problem in that regard either.
- Sprinkle some more const on tables.
hence existing applications like webcamd are expecting that.
This problem was introduced by SVN change 214221 where cdev=
was replaced by ugen= by accident. Solve this problem by
redefining cdev= in devd notifications.
MFC after 3 days.
Approved by: thompsa (mentor)
i.e. alignment, max_address, max_iosize and segsize (only max_address is
thought to have an negative impact regarding this issue though), after
calling ata_dmainit() either directly or indirectly so these values have
no effect or at least no effect on the DMA tags and the defaults are used
for the latter instead. So change the drivers to set these parameters
up-front and ata_dmainit() to honor them.
Reviewd by: mav
MFC after: 1 month
- This adds a VM SRIOV interface, ixv, it is however
transparent to the user, it links with the ixgbe.ko,
but when ixgbe is loaded in a virtualized guest with
SRIOV configured this will be detected.
- Sync shared code to latest
- Many bug fixes and improvements, thanks to everyone
who has been using the driver and reporting issues.
the dev.fxp.%d.noflow tunable as the same effect can now be achieved with
ifconfig(8) by setting the flowcontrol media option as desired (besides
the tunable never having a chance to actually enable flow control support
so far).
In joint forces with: yongari
- Fix a bug where TCO_BOOT_STS was supposed to be cleared after
TCO_SECOND_TO_STS and not before.
Sponsored by: Sandvine Incorporated
Submitted by: Mark Johnston <mjohnston at sandvine dot com>
Reviewed by: des
MFC after: 10 days
support multi-queue but the hardware limitation made it hard to
implement supporting multi-queue. Allocating more than necessary
vectors is resource waste and it can be added back when we
implement multi-queue support.
number of retry to be performed whenever controller found RX
descriptor was empty. RX empty interrupt is generated only when the
retry counter is over. Experimentation shows retrying RX descriptor
loading increased number of dropped frames under flow-control
enabled environments so disable it and have controller generate RX
empty interrupt as fast as it can.
While I'm here fix RXCSR_DESC_RT_CNT macro.
(wrong unit number for a host controller) when the module is load /
unloaded repeatly. Attaching the USB pf is moved to usbus device's
attach.
Pointed by: yongari
disable ASPM L0S and L1 LINK states on 82573, 82574,
and 82583. The theory is that this is behind certain
hangs being experienced by some customers.
Also included a small optimization in the rxeof routine
that was in my internal code.
Change the PBA size for pchlan, it was incorrect.
MFC after: 3 days
- Fixes from John Baldwin: vlan shadow tables made per/interface,
make vlan hw setup only happen when capability enabled, and
finally, make a tuneable interrupt rate. Thanks John!
- Tweaked watchdog handling to avoid any false positives, now
detection is in the TX clean path, with only the final check
and init happening in the local timer.
- limit queues to 8 for all devices, with 82576 or 82580 on
larger machines it can get greater than this, and it seems
mostly a resource waste to do so. Even 8 might be high but
it can be manually reduced.
- use 2k, 4k and now 9k clusters based on the MTU size.
- rework the igb_refresh_mbuf() code, its important to
make sure the descriptor is rewritten even when reusing
mbufs since writeback clobbers things.
MFC: in a few days, this delta needs to get to 8.2
Shorten the descriptive strings for Huawei devices. The vendor or
operator name should not be included in the device name.
Submitted by: Emile Coetzee
MFC after: 3 days
- Partially revert r172334; as it turns out the DELAYs in gem_reset_{r,t}x()
are actually necessary although bus space barriers and gem_bitwait() are
used, otherwise the controller may trigger an IOMMU errors on at least
sparc64. This is in line with what Linux and OpenSolaris do.
- Add some DSP init code for BCM5221. The values derived from Apple's GMAC
driver and the same init code also exists in Linux's sungem_phy driver.
- Only read media status bits when they are valid.
Obtained from: NetBSD, OpenBSD
autonegotiation along with manual media selection and also only report flow
control status when BMCR_AUTOEN is set (at least with gentbi(4) determining
the flow control status results in false-positives when not set), use
MIIF_NOMANPAUSE.
autonegotiation along with manual media selection and ukphy_status() also
only reports flow control status when BMCR_AUTOEN is set (at least with
gentbi(4) determining the flow control status results in false-positives
when not set), use MIIF_NOMANPAUSE.
The Myri10GE NIC will assume all TSO frames contain partial checksum,
and will emit TSO segments with bad TCP checksums if a TSO frame
contains a full checksum. The mxge driver takes care to make sure
that TSO is disabled when checksum offload is disabled for this
reason. However, modules that modify packet contents (like pf) may
end up completing a checksum on a TSO frame, leading to the NIC emitting
TSO segments with bad checksums.
To workaround this, restore the partial checksum in the mxge driver
when we're fed a TSO frame with a full checksum.
Reported by: Bob Healey
MFC after: 3 days
packets which go through each USB host controllers. Its implementations
are almost based on BPF code and very similar with it except it's
little bit customized for USB packet only. The userland program
usbdump(8) would be committed soon.
Discussed with: hps, thompsa, yongari
insertion/stripping and it also supports TSO over VLAN. Implement
TSO over VLAN support for MCP55 controller.
While I'm here clean up SIOCSIFCAP ioctl handler. Since nfe(4)
sets ifp capabilities based on various hardware flags in device
attach, there is no need to check hardware flags again in
SIOCSIFCAP ioctl handler. Also fix a bug which toggled both TX and
RX checksum offloading even if user requested either TX or RX
checksum configuration change.
Tested by: Rob Farmer ( rfarmer <> predatorlabs dot net )
of the MAC driver in order to attach miibus(4) on the first pass instead of
falling through to also calling it on the device_t of miibus(4). The latter
code flow was intended to attach the PHY drivers the same way regardless of
whether it's the first or a repeated pass, modulo the bus_generic_attach()
call in miibus_attach() which shouldn't be there. However, it turned out
that these variants cause miibus(4) to be attached twice under certain
conditions when using MAC drivers as modules.
Submitted by: yongari
MFC after: 3 days
not provide any MAC configuration interface for resolved flow
control parameters. There is even no register that configures water
mark which will control generation of pause frames.
However enabling flow control surely enhanced performance a lot.
such that nfe(4) does not work with MSI-X. When MSI-X support was
introduced, I remember MCP55 controller worked without problems so
the issue could be either PCI bridge or BIOS issue. But I also
noticed snd_hda(4) disabled MSI on all MCP55 chipset so I'm still
not sure this is generic issue of MCP55 chipset. If this was PCI
bridge issue we would have added it to a system wide black-list
table but it's not clear to me at this moment whether it was caused
by either broken BIOS or silicon bug of MCP55 chipset.
To workaround the issue, maintain a MSI/MSI-X black-list table in
driver and lookup base board manufacturer and product name from the
table before attempting to use MSI-X. If driver find an matching
entry, nfe(4) will not use MSI/MSI-X and fall back on traditional
INTx mode. This approach should be the last resort since it relies
on smbios and if another instance of MSI/MSI-X breakage is reported
with different maker/product, we may have to get the PCI bridge
black-listed instead of adding an new entry.
PR: kern/152150
K3765 datacard. After ejecting this device, it reappears using
the normal K3765 ID. It does not switch automatically
Reviewed by: n_hibma
Obtained from: OpenBSD
MFC after: 2 weeks
of certain MAC models from brgphy(4) to bge(4) where it belongs. While at it,
update the list of models having that restriction to what OpenBSD uses, which
in turn seems to have obtained that information from the Linux tg3 driver.
annex 31B full duplex flow control as well as the IFM_1000_T master
support committed in r215297. For atphy(4) and jmphy(4) this includes
changing these PHY drivers to no longer unconditionally advertise
support for flow control but only if the selected media has IFM_FLOW
set (or MIIF_FORCEPAUSE is set).
- Rename {atphy,jmphy}_auto() to {atphy,jmphy}_setmedia() as these handle
other media types as well.
Reviewed by: yongari (plus additional testing)
Obtained from: NetBSD (partially), OpenBSD (partially)
MFC after: 2 weeks
support in mii(4):
- Merge generic flow control advertisement (which can be enabled by
passing by MIIF_DOPAUSE to mii_attach(9)) and parsing support from
NetBSD into mii_physubr.c and ukphy_subr.c. Unlike as in NetBSD,
IFM_FLOW isn't implemented as a global option via the "don't care
mask" but instead as a media specific option this. This has the
following advantages:
o allows flow control advertisement with autonegotiation to be
turned on and off via ifconfig(8) with the default typically
being off (though MIIF_FORCEPAUSE has been added causing flow
control to be always advertised, allowing to easily MFC this
changes for drivers that previously used home-grown support for
flow control that behaved that way without breaking POLA)
o allows to deal with PHY drivers where flow control advertisement
with manual selection doesn't work or at least isn't implemented,
like it's the case with brgphy(4), e1000phy(4) and ip1000phy(4),
by setting MIIF_NOMANPAUSE
o the available combinations of media options are readily available
from the `ifconfig -m` output
- Add IFM_FLOW to IFM_SHARED_OPTION_DESCRIPTIONS and IFM_ETH_RXPAUSE
and IFM_ETH_TXPAUSE to IFM_SUBTYPE_ETHERNET_OPTION_DESCRIPTIONS so
these are understood by ifconfig(8).
o Make the master/slave support in mii(4) actually usable:
- Change IFM_ETH_MASTER from being implemented as a global option via
the "don't care mask" to a media specific one as it actually is only
applicable to IFM_1000_T to date.
- Let mii_phy_setmedia() set GTCR_MAN_MS in IFM_1000_T slave mode to
actually configure manually selected slave mode (like we also do in
the PHY specific implementations).
- Add IFM_ETH_MASTER to IFM_SUBTYPE_ETHERNET_OPTION_DESCRIPTIONS so it
is understood by ifconfig(8).
o Switch bge(4), bce(4), msk(4), nfe(4) and stge(4) along with brgphy(4),
e1000phy(4) and ip1000phy(4) to use the generic flow control support
instead of home-grown solutions via IFM_FLAGs. This includes changing
these PHY drivers and smcphy(4) to no longer unconditionally advertise
support for flow control but only if the selected media has IFM_FLOW
set (or MIIF_FORCEPAUSE is set) and implemented for these media variants,
i.e. typically only for copper.
o Switch brgphy(4), ciphy(4), e1000phy(4) and ip1000phy(4) to report and
set IFM_1000_T master mode via IFM_ETH_MASTER instead of via IFF_LINK0
and some IFM_FLAGn.
o Switch brgphy(4) to add at least the the supported copper media based on
the contents of the BMSR via mii_phy_add_media() instead of hardcoding
them. The latter approach seems to have developed historically, besides
causing unnecessary code duplication it was also undesirable because
brgphy_mii_phy_auto() already based the capability advertisement on the
contents of the BMSR though.
o Let brgphy(4) set IFM_1000_T master mode on all supported PHY and not
just BCM5701. Apparently this was a misinterpretation of a workaround
in the Linux tg3 driver; BCM5701 seem to require RGPHY_1000CTL_MSE and
BRGPHY_1000CTL_MSC to be set when configuring autonegotiation but
this doesn't mean we can't set these as well on other PHYs for manual
media selection.
o Let ukphy_status() report IFM_1000_T master mode via IFM_ETH_MASTER so
IFM_1000_T master mode support now is generally available with all PHY
drivers.
o Don't let e1000phy(4) set master/slave bits for IFM_1000_SX as it's
not applicable there.
Reviewed by: yongari (plus additional testing)
Obtained from: NetBSD (partially), OpenBSD (partially)
MFC after: 2 weeks
case to previous panic behavior.
I have a real fix that changes the sg dma tag allocation
to be limited to the under 4GB address space but would
prefer to have review before committing.
Bug fixes:
* Fixed "inquiry data fails comparion at DV1 step"
* Fixed bad range input in bus_alloc_resource for ADAPTER_TYPE_B
* Fixed arcmsr driver prevent arcsas support for Areca SAS HBA ARC13x0
Many thanks to Areca for continuing to support FreeBSD.
This commit is intended for MFC before 8.2-RELEASE.
Submitted by: Ching-Lung Huang <ching2048 areca com tw>
The external gpio pins are connected to a PLD on the i2c bus, unfortunatley
this device does not conform by failing to send an ack after each byte written.
The iicbb driver will abort the transfer when the address is not ack'd and it
would introduce a lot of churn to be able to pass a flag down to
iicbb_start/iicbb_write. Instead we do bad things by grabbing the iicbus but
then doing our own bit banging.
controller does not perform automatic switching from 1000Mbps link
to 10/100Mbps link when WOL is activated. Implement establishing
10/100Mps link with auto-negotiation in driver. Link status change
handler was modified to remove taskqueue based approach since driver
now needs synchronous handling for link establishment.
Submitted by: Yamagi Burmeister (lists <> yamagi.org ) (initial version)
Tested by: Yamagi Burmeister (lists <> yamagi.org )
MFC after: 1 week
and updated comments in the usb_quirk.h header file.
The main purpose of this is to expose the quirks for ejecting 3G
modules. usb_modeswitch in Linux does a great job of collecting
information on these, and with the quirks module people can try out the
modeswitch config file entries on FreeBSD, hence the SCSI strings in the
man page.
MFC after: 2 weeks
does-not-exist error when no client interface module is installed instead
of dereferencing NULL pointers. This eases implementation of platforms
that may or may not have Open Firmware.
It seems RTL8169/RTL8168/RTL810xE has a kind of interrupt
moderation mechanism but it is not documented at all. The magic
value dramatically reduced number of interrupts without noticeable
performance drops so apply it to all RTL8169/RTL8169 controllers.
Vendor's FreeBSD driver also applies it to RTL810xE controllers but
their Linux driver explicitly cleared the register, so do not
enable interrupt moderation for RTL810xE controllers.
While I'm here sort 8169 specific registers.
Obtained from: RealTek FreeBSD driver
There were a couple of attempts in the past to reduce it since it
took more than 1ms. Because mii_tick() periodically polls link
status, waiting more than 1ms for each GMII register access was
overkill. Unfortunately all previous attempts were failed with
various ways on different controllers.
This time, add additional 20us dealy at the end of GMII register
access which seems to requirement of all RealTek controllers to
issue next GMII register access request. This is the same way what
Linux does.
controllers. sk(4) never reprogrammed station address for Yukon
controllers so overriding station address with ifconfig(8) was not
possible.
Fix the bug by reprogramming all registers that control station
address, flow-control and virtual station address. Virtual station
address has no use at this moment since driver does not make use of
fail over feature.
Tested by: "Mikhail T." <mi+thun <> aldan.algebra.com>
MFC after: 1 week
the IEEE80211_C_RATECTL flag set, default to NONE for all drivers. Only if
a driver calls ieee80211_ratectl_init() check if the NONE algo is still
selected and try to use AMRR in that case. Drivers are still free to use
any other algo by calling ieee80211_ratectl_set() prior to the
ieee80211_ratectl_init() call.
After this change it is now safe to assume that a ratectl algo is always
available and selected, which renders the IEEE80211_C_RATECTL flag pretty
much useless. Therefore revert r211314 and 211546.
Reviewed by: rpaulo
MFC after: 2 weeks
based devices (QUALCOMMINC 0x2000). He made it use SCSI eject instead of
ZTE STOR eject. This prevented my ZTE MF626 dongle from switching.
- Apply both eject methods for ZTE STOR based devices. Works on my as
well as mav's device.
- Remove the duplicate.
- Sort the usbdevs entries for Qualcomm so this won't happen again.
- Add bootverbose message displaying the fact that we are ejecting (and
how).
Reviewed by: mav
MFC after: 2 weeks
copied as a template for _SRS, a string pointer for descriptor name is also
copied and it becomes stale as soon as it gets de-allocated[2]. Now _CRS is
used as a template for _SRS as ACPI specification suggests if it is usable.
The template from _PRS is still utilized but only when _CRS is not available
or broken. To avoid use-after-free the problem in this case, however, only
mandatory fields are copied, optional data is removed, and structure length
is adjusted accordingly.
Reported by: hps[1]
Analyzed by: avg[2]
Tested by: hps
useful counters like rl_missed_pkts is 16 bits quantity which is
too small to hold meaningful information happened in a second. This
means driver should frequently read these counters in order not to
lose accuracy and that approach is too inefficient in driver's
view. Moreover it seems there is no way to trigger an interrupt to
detect counter near-full or wraparound event as well as lacking
clearing the MAC counters. Another limitation of reading the
counters from RealTek controllers is lack of interrupt firing at
the end of DMA cycle of MAC counter read request such that driver
have to poll the end of the DMA which is a time consuming process
as well as inefficient. The more severe issue of the MAC counter
read request is it takes too long to complete the DMA. All these
limitation made maintaining MAC counters in driver impractical. For
now, just provide simple sysctl interface to trigger reading the
MAC counters. These counters could be used to track down driver
issues. Users can read MAC counters maintained in controller with
the following command.
#sysctl dev.re.0.stats=1
While I'm here add check for validity of dma map and allocated
memory before unloading/freeing them.
Tested by: rmacklem
information through devd. My E220 now produces the notification (1 line):
+u3g0 at bus=1 hubaddr=1 port=0 devaddr=2 interface=0 \
vendor=0x12d1 product=0x1003 devclass=0x00 devsubclass=0x00 \
sernum="" release=0x0000 intclass=0xff intsubclass=0xff \
ttyname=U0 ttyports=2 on uhub0
Note: serial/ufoma and net/uhso still provide port number and tty name
(uhso only) information through sysctls, which should now be removed.
Reviewed by: hpselasky
- Fix the loop count on detach (causing a panic on detaching a serial
dongle).
- Increase a buffer in case some driver want extra long tty device names
(postfixing the purpose of the tty for example, e.g. u3g.ppp).
notification. devd would stop evaluating at 'at' (not '<k>=<v>') and
hence prevent 'port=X' (and 'bus=<"on" string>) from making it into the
environment for the devd action.
Reviewed by: hselasky
MFC after: 2 weeks
- hw.usb.ucom.cons_unit is now split into
hw.usb.ucom.cons_unit/...cons_subunit.
Note: The tunable/sysctl hw.usb.ucom.cons_unit needs to be reviewed if
a) a console was defined a USB serial devices, and a USB device with
more than 1 subunit is present, and this device is attached before the
device functioning as a console
or
b) a console was defined on a USB device with more than 1 subunit
Reviewed by: hps
MFC after: 2 weeks
about but otherwise ignored. When allowing the master to be set manually via
ifconfig(8) by adding the former to IFM_SUBTYPE_ETHERNET_OPTION_DESCRIPTIONS
(as it should be) it seems to be unfavorable that a machine can be made to
panic with a simple ifconfig(8) invocation.
not able to trigger the issue with sample boards, some users seems
to suffer from freeze/lockup when system is booted without UTP cable
plugged in. I'm not sure whether this is BIOS issue or controller
bug. This change fixes AR8132 lockup issue seen on EEE PC.
Reported by: kmoore
Tested by: kmoore
In xbb_detach() only perform cleanup of our taskqueue and
device statistics structures if they have been initialized.
This avoids a panic when xbb_detach() is called on a partially
initialized device instance, due to an early failure in
attach.
Sponsored by: Spectra Logic Corporation
ip and tcp pointers were not reset after some
pullups. In practice this led to an NFS mount
failure when using UDP reported by Kevin Lo,
thanks Kevin. Fix from yongari, thank you!
the dual port BCM5717 and BCM5718 devices which are intended for
mainstream workstation and entry-level server designs and
represents the twelfth generation of NetXtreme Ethernet controllers.
This family is the successor to the BCM5714/BCM5715 family and
supports IPv4/IPv6 checksum offloading, TSO, VLAN hardware tagging,
jumbo frames, MSI/MSIX, IOV, RSS and TSS.
This change set supports all hardware features except IOV and
RSS/TSS. Unlike its predecessors, only extended RX buffer
descriptors can be posted to the jumbo producer ring. Single RX
buffer descriptors for jumbo frame are not supported. RSS requires
a more substantial set of changes and will apply to a larger set
of NetXtreme devices so RSS/TSS multi-queue support will be
implemented in a future releases.
Special thanks to Broadcom who kindly sent a sample board to me
and to davidch who gave provided the initial support code.
Submitted by: davidch (initial version)
HW donated by: Broadcom
'hw.acpi.remove_interface'. hw.acpi.install_interface lets you install new
interfaces. Conversely, hw.acpi.remove_interface lets you remove OS
interfaces from the pre-defined list in ACPICA. For example,
hw.acpi.install_interface="FreeBSD"
lets _OSI("FreeBSD") method to return 0xffffffff (or success) and
hw.acpi.remove_interface="Windows 2009"
lets _OSI("Windows 2009") method to return zero (or failure). Both are
comma-separated lists and leading white spaces are ignored. For example,
the following examples are valid:
hw.acpi.install_interface="Linux, FreeBSD"
hw.acpi.remove_interface="Windows 2006, Windows 2006.1"
- Chasin down bogus watchdogs has led to an improved
design to this handling, the hang decision takes
place in the tx cleanup, with only a simple report
check in local_timer. Our tests have shown no false
watchdogs with this code.
- VLAN fixes from jhb, the shadow vfta should be per
interface, but as global it was not. Thanks John.
- Bug fixes in the support for new PCH2 hardware.
- Thanks for all the help and feedback on the driver,
changes to lem with be coming shortly as well.
within the first 4 bytes of the EHCI memory space. For controllers that
use big-endian MMIO, reading them with 1- and 2-byte reads would then
return the wrong values. Instead, read the combined register with a 4-byte
read and mask out the interesting quantities.
VLAN hardware tagging to make TSO work over VLAN. So if VLAN
hardware tagging is disabled explicitly clear TSO over VLAN. While
I'm here allow disabling VLAN TX checksum offloading.
Tested by: Liudas < liudasb <> centras dot lt >
MFC after: 10 days
converted to use the mii_phy_add_media()/mii_phy_setmedia() pair instead
of mii_add_media()/mii_anar() remove the latter.
- Declare mii_media mii_media_table static as it shouldn't be used outside
of mii_physubr.c.
MFC after: never
interface also has such connectors.
- In tl_attach() unify three different ways of obtaining the device and
vendor IDs and remove the now obsolete tl_dinfo from tl_softc.
- Given that tlphy(4) only handles the integrated PHYs of NICs driven by
tl(4) make it only probe on the latter.
- Switch mlphy(4) and tlphy(4) to use mii_phy_add_media()/mii_phy_setmedia().
- Simplify looking for the respective companion PHY in mlphy(4) and tlphy(4)
by ignoring the native one by just comparing the device_t's directly rather
than the device name.
- Use mii_phy_add_media() instead of mii_add_media(). I'm not sure how
this driver actually managed to work before as mii_add_media() is
intended to be used to gether with mii_anar() while mii_phy_add_media()
is intended to be used with mii_phy_setmedia(), however this driver
mii_add_media() along with mii_phy_setmedia().
to BCM6906 A0/A2. This should fix a long standing BCM5906 A2 lockup
issues. Data sheet explicitly mentions BCM5906 A0, A1 and A2 use
de-pipelined mode on these revisions.
Special thanks to Buganini who tried all combinations of
experimental patches for more than 10 days.
Tested by: Buganini <buganini <> gmail dot com >
the association notification), the included information though always
contains an elem block with an odd number of bytes. We handle the last
byte as if it might contain a whole elem block, this of course is not
true as one byte is not enough to hold a block, we therefore discard the
complete frame. The solution here is to subtract one from the actual
notification length, this is also what the Linux driver does. With this
change the frames ends exactly where the last elem block ends.
This commit also reverts r214160 which is no longer required and now even
wrong.
MFC after: 1 week
auto-negotiation results in half-duplex operation, excess collision
on the ethernet link may cause internal chip delays that may result
in subsequent valid frames being dropped due to insufficient
receive buffer resources. The workaround is to choose de-pipeline
method as a flow control decision for SDI. De-pipeline method
allows only 1 data in TxMbuf at a time such that a request to RDMA
from SDI is made only when TxMbuf is empty. Thanks for david for
providing detailed errata information.
PCI-express or PCI-X capabilities if we are running in a virtual machine.
- Whitelist the Intel 82440 chipset used by QEMU.
Tested by: jfv
MFC after: 1 week
break the loop instead. We want to run the code after the while loop
to set an associd and capinfo. If we don't do this net80211 will drop
frames because it assumes the node has not yet been associated.
MFC after: 1 week
ignore BARs that are invalid due to having a size of zero, not to ignore
BARs with an existing base of zero. While here, reorganize the code
slightly to make the intent clearer.
Reported by: avg
MFC after: 1 week
Specification Rev. 1.2. Rename pp_pcmcsr field of PM capabilities to pp_bse
to avoid further confusions and adjust some comments accordingly. The real
PMCSR (Power Management Control/Status Register) is PCIR_POWER_STATUS and
it is actually BSE (PCI-to-PCI Bridge Support Extensions) register.
of proper value. It caused bunch of "EMPTY CRPB" messages and potentially
may cause premature requests completion, which could cause data corruption.
For most cases it seems enough to just reread register to get proper value.
To protect against worse cases - erase processed queue entries with
impossible values and ignore them if problem still happen.
released a drver lock for shared interrupt case such that it caused
panic. While I'm here check whether driver is still running before
serving TX/RX handler.
Reported by: Jerahmy Pocott < QUAKENET1 <> optusnet dot com dot au >
Tested by: Jerahmy Pocott < QUAKENET1 <> optusnet dot com dot au >
MFC after: 3 days
receive two back-to-back send BDs with less than or equal to 8
total bytes then the device may hang. The two back-to-back send
BDs must be in the same frame for this failure to occur.
Thanks to davidch for detailed errata information.
Reviewed by: davidch
o Add support for backend devices (e.g. blkback)
o Implement extensions to the Xen para-virtualized block API to allow
for larger and more outstanding I/Os.
o Import a completely rewritten block back driver with support for fronting
I/O to both raw devices and files.
o General cleanup and documentation of the XenBus and XenStore support code.
o Robustness and performance updates for the block front driver.
o Fixes to the netfront driver.
Sponsored by: Spectra Logic Corporation
sys/xen/xenbus/init.txt:
Deleted: This file explains the Linux method for XenBus device
enumeration and thus does not apply to FreeBSD's NewBus approach.
sys/xen/xenbus/xenbus_probe_backend.c:
Deleted: Linux version of backend XenBus service routines. It
was never ported to FreeBSD. See xenbusb.c, xenbusb_if.m,
xenbusb_front.c xenbusb_back.c for details of FreeBSD's XenBus
support.
sys/xen/xenbus/xenbusvar.h:
sys/xen/xenbus/xenbus_xs.c:
sys/xen/xenbus/xenbus_comms.c:
sys/xen/xenbus/xenbus_comms.h:
sys/xen/xenstore/xenstorevar.h:
sys/xen/xenstore/xenstore.c:
Split XenStore into its own tree. XenBus is a software layer built
on top of XenStore. The old arrangement and the naming of some
structures and functions blurred these lines making it difficult to
discern what services are provided by which layer and at what times
these services are available (e.g. during system startup and shutdown).
sys/xen/xenbus/xenbus_client.c:
sys/xen/xenbus/xenbus.c:
sys/xen/xenbus/xenbus_probe.c:
sys/xen/xenbus/xenbusb.c:
sys/xen/xenbus/xenbusb.h:
Split up XenBus code into methods available for use by client
drivers (xenbus.c) and code used by the XenBus "bus code" to
enumerate, attach, detach, and service bus drivers.
sys/xen/reboot.c:
sys/dev/xen/control/control.c:
Add a XenBus front driver for handling shutdown, reboot, suspend, and
resume events published in the XenStore. Move all PV suspend/reboot
support from reboot.c into this driver.
sys/xen/blkif.h:
New file from Xen vendor with macros and structures used by
a block back driver to service requests from a VM running a
different ABI (e.g. amd64 back with i386 front).
sys/conf/files:
Adjust kernel build spec for new XenBus/XenStore layout and added
Xen functionality.
sys/dev/xen/balloon/balloon.c:
sys/dev/xen/netfront/netfront.c:
sys/dev/xen/blkfront/blkfront.c:
sys/xen/xenbus/...
sys/xen/xenstore/...
o Rename XenStore APIs and structures from xenbus_* to xs_*.
o Adjust to use of M_XENBUS and M_XENSTORE malloc types for allocation
of objects returned by these APIs.
o Adjust for changes in the bus interface for Xen drivers.
sys/xen/xenbus/...
sys/xen/xenstore/...
Add Doxygen comments for these interfaces and the code that
implements them.
sys/dev/xen/blkback/blkback.c:
o Rewrite the Block Back driver to attach properly via newbus,
operate correctly in both PV and HVM mode regardless of domain
(e.g. can be in a DOM other than 0), and to deal with the latest
metadata available in XenStore for block devices.
o Allow users to specify a file as a backend to blkback, in addition
to character devices. Use the namei lookup of the backend path
to automatically configure, based on file type, the appropriate
backend method.
The current implementation is limited to a single outstanding I/O
at a time to file backed storage.
sys/dev/xen/blkback/blkback.c:
sys/xen/interface/io/blkif.h:
sys/xen/blkif.h:
sys/dev/xen/blkfront/blkfront.c:
sys/dev/xen/blkfront/block.h:
Extend the Xen blkif API: Negotiable request size and number of
requests.
This change extends the information recorded in the XenStore
allowing block front/back devices to negotiate for optimal I/O
parameters. This has been achieved without sacrificing backward
compatibility with drivers that are unaware of these protocol
enhancements. The extensions center around the connection protocol
which now includes these additions:
o The back-end device publishes its maximum supported values for,
request I/O size, the number of page segments that can be
associated with a request, the maximum number of requests that
can be concurrently active, and the maximum number of pages that
can be in the shared request ring. These values are published
before the back-end enters the XenbusStateInitWait state.
o The front-end waits for the back-end to enter either the InitWait
or Initialize state. At this point, the front end limits it's
own capabilities to the lesser of the values it finds published
by the backend, it's own maximums, or, should any back-end data
be missing in the store, the values supported by the original
protocol. It then initializes it's internal data structures
including allocation of the shared ring, publishes its maximum
capabilities to the XenStore and transitions to the Initialized
state.
o The back-end waits for the front-end to enter the Initalized
state. At this point, the back end limits it's own capabilities
to the lesser of the values it finds published by the frontend,
it's own maximums, or, should any front-end data be missing in
the store, the values supported by the original protocol. It
then initializes it's internal data structures, attaches to the
shared ring and transitions to the Connected state.
o The front-end waits for the back-end to enter the Connnected
state, transitions itself to the connected state, and can
commence I/O.
Although an updated front-end driver must be aware of the back-end's
InitWait state, the back-end has been coded such that it can
tolerate a front-end that skips this step and transitions directly
to the Initialized state without waiting for the back-end.
sys/xen/interface/io/blkif.h:
o Increase BLKIF_MAX_SEGMENTS_PER_REQUEST to 255. This is
the maximum number possible without changing the blkif
request header structure (nr_segs is a uint8_t).
o Add two new constants:
BLKIF_MAX_SEGMENTS_PER_HEADER_BLOCK, and
BLKIF_MAX_SEGMENTS_PER_SEGMENT_BLOCK. These respectively
indicate the number of segments that can fit in the first
ring-buffer entry of a request, and for each subsequent
(sg element only) ring-buffer entry associated with the
"header" ring-buffer entry of the request.
o Add the blkif_request_segment_t typedef for segment
elements.
o Add the BLKRING_GET_SG_REQUEST() macro which wraps the
RING_GET_REQUEST() macro and returns a properly cast
pointer to an array of blkif_request_segment_ts.
o Add the BLKIF_SEGS_TO_BLOCKS() macro which calculates the
number of ring entries that will be consumed by a blkif
request with the given number of segments.
sys/xen/blkif.h:
o Update for changes in interface/io/blkif.h macros.
o Update the BLKIF_MAX_RING_REQUESTS() macro to take the
ring size as an argument to allow this calculation on
multi-page rings.
o Add a companion macro to BLKIF_MAX_RING_REQUESTS(),
BLKIF_RING_PAGES(). This macro determines the number of
ring pages required in order to support a ring with the
supplied number of request blocks.
sys/dev/xen/blkback/blkback.c:
sys/dev/xen/blkfront/blkfront.c:
sys/dev/xen/blkfront/block.h:
o Negotiate with the other-end with the following limits:
Reqeust Size: MAXPHYS
Max Segments: (MAXPHYS/PAGE_SIZE) + 1
Max Requests: 256
Max Ring Pages: Sufficient to support Max Requests with
Max Segments.
o Dynamically allocate request pools and segemnts-per-request.
o Update ring allocation/attachment code to support a
multi-page shared ring.
o Update routines that access the shared ring to handle
multi-block requests.
sys/dev/xen/blkfront/blkfront.c:
o Track blkfront allocations in a blkfront driver specific
malloc pool.
o Strip out XenStore transaction retry logic in the
connection code. Transactions only need to be used when
the update to multiple XenStore nodes must be atomic.
That is not the case here.
o Fully disable blkif_resume() until it can be fixed
properly (it didn't work before this change).
o Destroy bus-dma objects during device instance tear-down.
o Properly handle backend devices with powef-of-2 sector
sizes larger than 512b.
sys/dev/xen/blkback/blkback.c:
Advertise support for and implement the BLKIF_OP_WRITE_BARRIER
and BLKIF_OP_FLUSH_DISKCACHE blkif opcodes using BIO_FLUSH and
the BIO_ORDERED attribute of bios.
sys/dev/xen/blkfront/blkfront.c:
sys/dev/xen/blkfront/block.h:
Fix various bugs in blkfront.
o gnttab_alloc_grant_references() returns 0 for success and
non-zero for failure. The check for < 0 is a leftover
Linuxism.
o When we negotiate with blkback and have to reduce some of our
capabilities, print out the original and reduced capability before
changing the local capability. So the user now gets the correct
information.
o Fix blkif_restart_queue_callback() formatting. Make sure we hold
the mutex in that function before calling xb_startio().
o Fix a couple of KASSERT()s.
o Fix a check in the xb_remove_* macro to be a little more specific.
sys/xen/gnttab.h:
sys/xen/gnttab.c:
Define GNTTAB_LIST_END publicly as GRANT_REF_INVALID.
sys/dev/xen/netfront/netfront.c:
Use GRANT_REF_INVALID instead of driver private definitions of the
same constant.
sys/xen/gnttab.h:
sys/xen/gnttab.c:
Add the gnttab_end_foreign_access_references() API.
This API allows a client to batch the release of an array of grant
references, instead of coding a private for loop. The implementation
takes advantage of this batching to reduce lock overhead to one
acquisition and release per-batch instead of per-freed grant reference.
While here, reduce the duration the gnttab_list_lock is held during
gnttab_free_grant_references() operations. The search to find the
tail of the incoming free list does not rely on global state and so
can be performed without holding the lock.
sys/dev/xen/xenpci/evtchn.c:
sys/dev/xen/evtchn/evtchn.c:
sys/xen/xen_intr.h:
o Implement the bind_interdomain_evtchn_to_irqhandler API for HVM mode.
This allows an HVM domain to serve back end devices to other domains.
This API is already implemented for PV mode.
o Synchronize the API between HVM and PV.
sys/dev/xen/xenpci/xenpci.c:
o Scan the full region of CPUID space in which the Xen VMM interface
may be implemented. On systems using SuSE as a Dom0 where the
Viridian API is also exported, the VMM interface is above the region
we used to search.
o Pass through bus_alloc_resource() calls so that XenBus drivers
attaching on an HVM system can allocate unused physical address
space from the nexus. The block back driver makes use of this
facility.
sys/i386/xen/xen_machdep.c:
Use the correct type for accessing the statically mapped xenstore
metadata.
sys/xen/interface/hvm/params.h:
sys/xen/xenstore/xenstore.c:
Move hvm_get_parameter() to the correct global header file instead
of as a private method to the XenStore.
sys/xen/interface/io/protocols.h:
Sync with vendor.
sys/xeninterface/io/ring.h:
Add macro for calculating the number of ring pages needed for an N
deep ring.
To avoid duplication within the macros, create and use the new
__RING_HEADER_SIZE() macro. This macro calculates the size of the
ring book keeping struct (producer/consumer indexes, etc.) that
resides at the head of the ring.
Add the __RING_PAGES() macro which calculates the number of shared
ring pages required to support a ring with the given number of
requests.
These APIs are used to support the multi-page ring version of the
Xen block API.
sys/xeninterface/io/xenbus.h:
Add Comments.
sys/xen/xenbus/...
o Refactor the FreeBSD XenBus support code to allow for both front and
backend device attachments.
o Make use of new config_intr_hook capabilities to allow front and back
devices to be probed/attached in parallel.
o Fix bugs in probe/attach state machine that could cause the system to
hang when confronted with a failure either in the local domain or in
a remote domain to which one of our driver instances is attaching.
o Publish all required state to the XenStore on device detach and
failure. The majority of the missing functionality was for serving
as a back end since the typical "hot-plug" scripts in Dom0 don't
handle the case of cleaning up for a "service domain" that is not
itself.
o Add dynamic sysctl nodes exposing the generic ivars of
XenBus devices.
o Add doxygen style comments to the majority of the code.
o Cleanup types, formatting, etc.
sys/xen/xenbus/xenbusb.c:
Common code used by both front and back XenBus busses.
sys/xen/xenbus/xenbusb_if.m:
Method definitions for a XenBus bus.
sys/xen/xenbus/xenbusb_front.c:
sys/xen/xenbus/xenbusb_back.c:
XenBus bus specialization for front and back devices.
MFC after: 1 month
added with hw.pci.do_powerstate but the PCI version was splitted into two
separate tunables later and now this is completely stale. To make it worse,
PCI devices enumerated in ACPI tree ignore this tunable as it is handled by
a function in acpi_pci.c instead.
knowledges from the file. All PCI devices enumerated in ACPI tree must use
correct one from acpi_pci.c any way. Reduce duplicate codes as we did for
pci.c in r213905. Do not return ESRCH from PCIB_POWER_FOR_SLEEP method.
When the method is not found, just return zero without modifying the given
default value as it is completely optional. As a side effect, the return
state must not be NULL. Note there is actually no functional change by
removing ESRCH because acpi_pcib_power_for_sleep() always returns zero.
Adjust debugging messages and add new ones under bootverbose to help
debugging device power state related issues.
Reviewed by: jhb, imp (earlier versions)
- Implement proper combined mode decoding for Intel controllers to properly
identify SATA and PATA channels and associate ATA channels with SATA ports.
This fixes wrong reporting and in some cases hard resets to wrong SATA ports.
- Improve SATA registers support to handle hot-plug events and potentially
interface errors. For ICH5/6300ESB chipsets these registers accessible via
PCI config space. For later ones they may be accessible via PCI BAR(5).
- For controllers not generating interrupts on hot-plug events, implement
periodic status polling. Use it to detect hot-plug on Intel and VIA
controllers. Same probably could also be used for Serverworks and SIS.
To protect against malicious software, we demand that the file name is at
a particular location (i.e. appended to the mdio structure) for it to be
treated as in-kernel.
important for USB 2.0 devices and some of them reported to have problems
with large transactions. But USB 3.0 benchmarks show that limited number
of transactions per second on USB makes impossible to reach high transfer
speeds without using bigger transactions.
On my tests this change allows to read up to 220MB/s from USB-attached SSD
(at block size of 256-512KB), comparing to only 113MB/s without it.
Reviewed by: hselasky
the NIC drivers as well as the PHY drivers to take advantage of the
mii_attach() introduced in r213878 to get rid of certain hacks. For
the most part these were:
- Artificially limiting miibus_{read,write}reg methods to certain PHY
addresses; we now let mii_attach() only probe the PHY at the desired
address(es) instead.
- PHY drivers setting MIIF_* flags based on the NIC driver they hang
off from, partly even based on grabbing and using the softc of the
parent; we now pass these flags down from the NIC to the PHY drivers
via mii_attach(). This got us rid of all such hacks except those of
brgphy() in combination with bce(4) and bge(4), which is way beyond
what can be expressed with simple flags.
While at it, I took the opportunity to change the NIC drivers to pass
up the error returned by mii_attach() (previously by mii_phy_probe())
and unify the error message used in this case where and as appropriate
as mii_attach() actually can fail for a number of reasons, not just
because of no PHY(s) being present at the expected address(es).
This file was missed in r213893.
PowerMac7,2.
- The fcu driver lets us read and write the fan RPMs for all fans in the
PowerMac7,2. This driver is PowerMac specific.
- The ds1775 is a driver to read the temperature for the drive bay sensor.
- The max6690 is another driver to read temperatures. Here it is used to
read the inlet, the backside and the U3 heatsink temperature.
An additional driver, the ad7417, will follow later.
Thanks to nwhitehorn for guiding me through this driver development.
Approved by: nwhitehorn (mentor)
the NIC drivers as well as the PHY drivers to take advantage of the
mii_attach() introduced in r213878 to get rid of certain hacks. For
the most part these were:
- Artificially limiting miibus_{read,write}reg methods to certain PHY
addresses; we now let mii_attach() only probe the PHY at the desired
address(es) instead.
- PHY drivers setting MIIF_* flags based on the NIC driver they hang
off from, partly even based on grabbing and using the softc of the
parent; we now pass these flags down from the NIC to the PHY drivers
via mii_attach(). This got us rid of all such hacks except those of
brgphy() in combination with bce(4) and bge(4), which is way beyond
what can be expressed with simple flags.
While at it, I took the opportunity to change the NIC drivers to pass
up the error returned by mii_attach() (previously by mii_phy_probe())
and unify the error message used in this case where and as appropriate
as mii_attach() actually can fail for a number of reasons, not just
because of no PHY(s) being present at the expected address(es).
Reviewed by: jhb, yongari
- fix the leak of command struct on error
- simplify the cleanup logic
- EINPROGRESS is not a fatal error
- buggy comment and error message
Reviewed by: ken
