Where the cloudabi64 kernel can be used to execute 64-bit CloudABI
binaries, this one should be used for 32-bit binaries. Right now it
works on i386 and amd64.
This driver only supports 10Mb Ethernet using PIO (the hardware supports
DMA, but the driver only does PIO). There are not any PCCard adapters
supported by this driver, only ISA cards. In addition, it does not use
bus_space but instead uses bcopy with volatile pointers triggering a
host of warnings. (if_ie.c is one of 3 files always built with
-Wno-error)
Relnotes: yes
The wl(4) driver supports pre-802.11 PCCard wireless adapters that
are slower than 802.11b. They do not work with any of the 802.11
framework and the driver hasn't been reported to actually work in a
long time.
Relnotes: yes
The si(4) driver supported multiport serial adapters for ISA, EISA, and
PCI buses. This driver does not use bus_space, instead it depends on
direct use of the pointer returned by rman_get_virtual(). It is also
still locked by Giant and calls for patch testing to convert it to use
bus_space were unanswered.
Relnotes: yes
This is a driver for a pre-ATAPI ISA CD-ROM adapter. As noted in
the manpage, this driver is only useful as a backend to cdcontrol to
play audio CDs since it doesn't use DMA, so its data performance is
"abysmal" (and that was true in the mid 90's).
The module works together with ipfw(4) and implemented as its external
action module.
Stateless NAT64 registers external action with name nat64stl. This
keyword should be used to create NAT64 instance and to address this
instance in rules. Stateless NAT64 uses two lookup tables with mapped
IPv4->IPv6 and IPv6->IPv4 addresses to perform translation.
A configuration of instance should looks like this:
1. Create lookup tables:
# ipfw table T46 create type addr valtype ipv6
# ipfw table T64 create type addr valtype ipv4
2. Fill T46 and T64 tables.
3. Add rule to allow neighbor solicitation and advertisement:
# ipfw add allow icmp6 from any to any icmp6types 135,136
4. Create NAT64 instance:
# ipfw nat64stl NAT create table4 T46 table6 T64
5. Add rules that matches the traffic:
# ipfw add nat64stl NAT ip from any to table(T46)
# ipfw add nat64stl NAT ip from table(T64) to 64:ff9b::/96
6. Configure DNS64 for IPv6 clients and add route to 64:ff9b::/96
via NAT64 host.
Stateful NAT64 registers external action with name nat64lsn. The only
one option required to create nat64lsn instance - prefix4. It defines
the pool of IPv4 addresses used for translation.
A configuration of instance should looks like this:
1. Add rule to allow neighbor solicitation and advertisement:
# ipfw add allow icmp6 from any to any icmp6types 135,136
2. Create NAT64 instance:
# ipfw nat64lsn NAT create prefix4 A.B.C.D/28
3. Add rules that matches the traffic:
# ipfw add nat64lsn NAT ip from any to A.B.C.D/28
# ipfw add nat64lsn NAT ip6 from any to 64:ff9b::/96
4. Configure DNS64 for IPv6 clients and add route to 64:ff9b::/96
via NAT64 host.
Obtained from: Yandex LLC
Relnotes: yes
Sponsored by: Yandex LLC
Differential Revision: https://reviews.freebsd.org/D6434
as defined in RFC 6296. The module works together with ipfw(4) and
implemented as its external action module. When it is loaded, it registers
as eaction and can be used in rules. The usage pattern is similar to
ipfw_nat(4). All matched by rule traffic goes to the NPT module.
Reviewed by: hrs
Obtained from: Yandex LLC
MFC after: 1 month
Relnotes: yes
Sponsored by: Yandex LLC
Differential Revision: https://reviews.freebsd.org/D6420
default. At least initially, the feature to support multiple TCP stacks is
aimed at supporting advanced use cases and TCP development, but it is not
necessarily aimed at a wide audience. Therefore, there is no need to build
and install the extra TCP stacks by default. Instead, the people who are
using or developing this functionality can add the extra option to build/
install the extra TCP stacks.
However, we do want to build the extra TCP stacks as part of test builds
(e.g. LINT or tinderbox) to ensure that developers who are testing their
changes will know that their changes do not break the additional TCP
stack modules.
After this change, a user will need to add WITH_EXTRA_TCP_STACKS=1 to
make.conf or the kernel config in order to build the extra TCP modules.
Differential Revision: https://reviews.freebsd.org/D6795
Reviewed by: sjg
Approved by: re (kib)
This is an initial work in progress to use the replacement bhnd
bus code for devices which support it.
* Add manpage updates for bhnd, bhndb, siba
* Add kernel options for bhnd, bhndbus, etc
* Add initial support in if_bwn_pci / if_bwn_mac for using bhnd
as the bus transport for suppoted NICs
* if_bwn_pci will eventually be the PCI bus glue to interface to bwn,
which will use the right backend bus to attach to, versus direct
nexus/bhnd attachments (as found in embedded broadcom devices.)
The PCI glue defaults to probing at a lower level than the bwn glue,
so bwn should still attach as per normal without a boot time tunable set.
It's also not fully fleshed out - the bwn probe/attach code needs to be
broken out into platform and bus specific things (just like ath, ath_pci,
ath_ahb) before we can shift the driver over to using this.
Tested:
* BCM4311, STA mode
* BCM4312, STA mode
Submitted by: Landon Fuller <landonf@landonf.org>
Differential Revision: https://reviews.freebsd.org/D6191
Make it compile only for i386/amd64 for now as it's been tested there.
It's quite possible it'll show up elsewhere and we can enable it
for other architectures later.
Tested:
* PC Engines APU1C4
Submitted by: Daniel Wyatt <daniel@dewyatt.com>
Reviewed by: adrian, loos
Differential Revision: https://reviews.freebsd.org/D5389
There's some upcoming work to add new chipset support here and I'd
like to only add 802.11n support to one driver, instead of both
urtwn and rtwn.
There's also missing support for things like 802.11n, some powersave
work, bluetooth integration/coexistence, etc, and also newer parts
(like 8192EU, maybe some 11ac parts, not sure yet.)
So, this is hopefully the first step in a longer set of steps to unify
rtwn/urtwn and extend it with more interesting chipset and functionality
support.
Reviewed by: kevlo
improve cancellation robustness.
Introduce a new file operation, fo_aio_queue, which is responsible for
queueing and completing an asynchronous I/O request for a given file.
The AIO subystem now exports library of routines to manipulate AIO
requests as well as the ability to run a handler function in the
"default" pool of AIO daemons to service a request.
A default implementation for file types which do not include an
fo_aio_queue method queues requests to the "default" pool invoking the
fo_read or fo_write methods as before.
The AIO subsystem permits file types to install a private "cancel"
routine when a request is queued to permit safe dequeueing and cleanup
of cancelled requests.
Sockets now use their own pool of AIO daemons and service per-socket
requests in FIFO order. Socket requests will not block indefinitely
permitting timely cancellation of all requests.
Due to the now-tight coupling of the AIO subsystem with file types,
the AIO subsystem is now a standard part of all kernels. The VFS_AIO
kernel option and aio.ko module are gone.
Many file types may block indefinitely in their fo_read or fo_write
callbacks resulting in a hung AIO daemon. This can result in hung
user processes (when processes attempt to cancel all outstanding
requests during exit) or a hung system. To protect against this, AIO
requests are only permitted for known "safe" files by default. AIO
requests for all file types can be enabled by setting the new
vfs.aio.enable_usafe sysctl to a non-zero value. The AIO tests have
been updated to skip operations on unsafe file types if the sysctl is
zero.
Currently, AIO requests on sockets and raw disks are considered safe
and are enabled by default. aio_mlock() is also enabled by default.
Reviewed by: cem, jilles
Discussed with: kib (earlier version)
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D5289
rtwnfw got added in r293009 and depends on source-less and
non-free microcode in sys/contrib/dev/rtwn.
PR: 205874
Submitted by: Fabian Keil
Obtained from: ElectroBSD
The mdio driver interface is generally useful for devices that require
MDIO without the full MII bus interface. This lifts the driver/interface
out of etherswitch(4), and adds a mdio(4) man page.
Submitted by: Landon Fuller <landon@landonf.org>
Differential Revision: https://reviews.freebsd.org/D4606
to do is to clean up the timer handling using the async-drain.
Other optimizations may be coming to go with this. Whats here
will allow differnet tcp implementations (one included).
Reviewed by: jtl, hiren, transports
Sponsored by: Netflix Inc.
Differential Revision: D4055
Use hhook(9) framework to achieve ability of loading and unloading
if_enc(4) kernel module. INET and INET6 code on initialization registers
two helper hooks points in the kernel. if_enc(4) module uses these helper
hook points and registers its hooks. IPSEC code uses these hhook points
to call helper hooks implemented in if_enc(4).
default and add a manual page for mlx5en. The mlx5 module contains
shared code for both infiniband and ethernet. The mlx5en module
contains specific code for ethernet functionality only. A mlx5ib
module is in the works for infiniband support.
Supported hardware:
- ConnectX-4: 10/20/25/40/50/56/100Gb/s speeds.
- ConnectX-4 LX: 10/25/40/50Gb/s speeds (low power consumption)
Refer to the mlx5en(4) manual page for a comprehensive list.
The team porting the mlx5 driver(s) to FreeBSD:
- Hans Petter Selasky <hselasky@freebsd.org>
- Oded Shanoon <odeds@mellanox.com>
- Meny Yossefi <menyy@mellanox.com>
- Shany Michaely <shanim@mellanox.com>
- Shahar Klein <shahark@mellanox.com>
- Daria Genzel <dariaz@mellanox.com>
- Mark Bloch <markb@mellanox.com>
Differential Revision: https://reviews.freebsd.org/D4163
Submitted by: Mark Block <markb@mellanox.com>
Sponsored by: Mellanox Technologies
Reviewed by: gnn @
MFC after: 3 days
work with the upcoming async-drain functionality. Tests can be added
to the tests directory and then the framework can be used to launch
those tests.
MFC after: 1 month
Sponsored by: Netflix Inc.
Differential Revision: https://reviews.freebsd.org/D1755
These are not target-specific modules, so the logic to build them should
be common. This also enables them for arm64.
Sponsored by: The FreeBSD Foundation
It turns out that it is pretty easy to make CloudABI work on ARM64. We
essentially only need to copy over the sysvec from AMD64 and ensure that
we use ARM64 specific registers.
As there is an overlap between function argument and return registers,
we do need to extend cloudabi64_schedtail() to only set its values if
we're actually forking. Not when we're creating a new thread.
Reviewed by: kib
Differential Revision: https://reviews.freebsd.org/D3917
Atheros.
Thanks to OpenBSD for providing a driver based on the original
Atheros open source driver circa 2008. This uses the early, pre-carl9170
atheros provided firmware.
It only supports 11bg at the moment. I've not tested it with 11a
(and so the TX rate control logic may be slightly wrong!) so if
you do have the dual-band version of this hardware please do let me know.
Tested:
* AR9170, TP-Link WN821N 2GHz.
TODO:
* Hook this up to a non-module build.
only gpiobus configured via FDT is supported. Bus enumeration is
supported. Devices are created for each device found. 1-Wire
temperature controllers are supported, but other drivers could be
written. Temperatures are polled and reported via a sysctl. Errors
are reported via sysctl counters. Mis-wired bus detection is included
for more trouble shooting. See ow(4), owc(4) and ow_temp(4) for
details of what's supported and known issues.
This has been tested on Raspberry Pi-B, Pi2 and Beagle Bone Black
with up to 7 devices.
Differential Revision: https://reviews.freebsd.org/D2956
Relnotes: yes
MFC after: 2 weeks
Reviewed by: loos@ (with many insightful comments)
I/OAT is also referred to as Crystal Beach DMA and is a Platform Storage
Extension (PSE) on some Intel server platforms.
This driver currently supports DMA descriptors only and is part of a
larger effort to upstream an interconnect between multiple systems using
the Non-Transparent Bridge (NTB) PSE.
For now, this driver is only built on AMD64 platforms. It may be ported
to work on i386 later, if that is desired. The hardware is exclusive to
x86.
Further documentation on ioat(4), including API documentation and usage,
can be found in the new manual page.
Bring in a test tool, ioatcontrol(8), in tools/tools/ioat. The test
tool is not hooked up to the build and is not intended for end users.
Submitted by: jimharris, Carl Delsey <carl.r.delsey@intel.com>
Reviewed by: jimharris (reviewed my changes)
Approved by: markj (mentor)
Relnotes: yes
Sponsored by: Intel
Sponsored by: EMC / Isilon Storage Division
Differential Revision: https://reviews.freebsd.org/D3456
if desired.
Retire randomdev_none.c and introduce random_infra.c for resident
infrastructure. Completely stub out random(4) calls in the "without
DEV_RANDOM" case.
Add RANDOM_LOADABLE option to allow loadable Yarrow/Fortuna/LocallyWritten
algorithm. Add a skeleton "other" algorithm framework for folks
to add their own processing code. NIST, anyone?
Retire the RANDOM_DUMMY option.
Build modules for Yarrow, Fortuna and "other".
Use atomics for the live entropy rate-tracking.
Convert ints to bools for the 'seeded' logic.
Move _write() function from the algorithm-specific areas to randomdev.c
Get rid of reseed() function - it is unused.
Tidy up the opt_*.h includes.
Update documentation for random(4) modules.
Fix test program (reviewers, please leave this).
Differential Revision: https://reviews.freebsd.org/D3354
Reviewed by: wblock,delphij,jmg,bjk
Approved by: so (/dev/random blanket)
Place all of the machine/pointer size independent code in a kernel
module called 'cloudabi'. All of the 64-bit specific code goes in a
separate module called 'cloudabi64'. The latter is only enabled on
amd64, as it is the only architecture supported.
