Remove two debugging printfs, even if hidden under boot -v.
They seemed to be of debug nature and always spit onto the
console when running camcontrol devlist -v.
Reviewed by: manu
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D25962
If the fdt node doesn't have a cd-gpios properties or if the node is set
as non-removable we do not init the card detection timeout task as it is
useless so don't schedule it too.
MFC after: 1 month
X-MFC-With: r359924
the dts to find the supported speeds and the regulators.
Not all DTS have every settings properly defined so host controller
will still have to add some caps themselves.
It also add a mmc_fdt_gpio_setup function which will read the cd-gpios
property and register it as the CD pin.
If the pin support interrupts one will be registered and the cd_helper
function will be called.
If the pin doesn't support interrupts the internal taskqueue will poll
for change and call the same cd_helper function.
mmc_fdt_gpio_setup will also parse the wp-gpio property and MMC drivers
can know the write-protect pin value by calling the
mmc_fdt_gpio_get_readonly function.
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D23267
Each segment can be up to 4096 bytes in chain structure according to the
RK3399 TRM Part 2.
Set the buffers in full ring where the last one point to the first one.
Correctly reports the MMC_IVAR_MAX_DATA.
Use CACHE_LINE_SIZE for bus_dma alignment.
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D23894
The IVAR_MAX_DATA is supposed to have the number of descriptor X the mmc
block size and desc_count contain all this information + 1.
Reported by: phk
MFC after: 1 week
r357614 added CTLFLAG_NEEDGIANT to make it easier to find nodes that are
still not MPSAFE (or already are but aren’t properly marked).
Use it in preparation for a general review of all nodes.
This is non-functional change that adds annotations to SYSCTL_NODE and
SYSCTL_PROC nodes using one of the soon-to-be-required flags.
Mark all obvious cases as MPSAFE. All entries that haven't been marked
as MPSAFE before are by default marked as NEEDGIANT
Approved by: kib (mentor, blanket)
Commented by: kib, gallatin, melifaro
Differential Revision: https://reviews.freebsd.org/D23718
BIO_READ and BIO_WRITE, we've handled this expanded syntax poorly in
drivers when the driver doesn't support a particular command. Do a
sweep and fix that.
Reported by: imp
Instead of first detaching the children(s) and then delete them,
use the device_delete_children function that does all of that.
MFC after: 1 month
Suggested by: ian
The driver used to always add the mmc device as it's child even
it no card was detected. Add a function that will detect if the
card is present or not and that will attach/detach the mmc device.
The function is either call on attach (as we won't have the interrupt
fired) or from two taskqueues. The first taskqueue will directly call
the function when the sdcard was present and is now removed and the other
one will delay a bit the attach when we didn't had a card and now have one.
This is mostly based on comments from the sdhci driver where it describe
a situation when the CD pin is detected before the others pins are connected.
MFC after: 1 month
This method will disable the regulators, clocks and assert the reset of
the module. It will also detach it's children (the mmc device) and release
it's resources.
While here enable the regulators on attach as we need them to power up
the sdcard or emmc.
MFC after: 1 month
o Remove All Rights Reserved from my notices
o imp@FreeBSD.org everywhere
o regularize punctiation, eliminate date ranges
o Make sure that it's clear that I don't claim All Rights reserved by listing
All Rights Reserved on same line as other copyright holders (but not
me). Other such holders are also listed last where it's clear.
Ignore only ENOENT (no DTS properties found) and ENODEV (driver not
present) non-zero return values from ext_resources.
Reviewed by: manu
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D22043
(resets, regulators, clocks) are not available.
Rely on a system initialization done by a bootloader in that cases.
This fixes operation on Terasic DE10-Pro (an Intel Stratix 10
development kit).
Sponsored by: DARPA, AFRL
If the bootloader enabled DMA we need to fully reset the DMA controller
otherwise we might have some stale data in it that provoke weird
behavior.
MFC after: 1 week
All MMCBR bridges have to implement all the MMCBR variables. This
implements them for everybody that currently doesn't.
A common routine for this should be written.
otherwise we panic.
dwmmc don't handle VCCQ (voltage for the IO line of the SD/eMMC) or
TIMING.
Add the needed accessor in the {read,write}_ivar functions.
Reviewed by: imp (previous version)
This allows replacing "sys/eventfilter.h" includes with "sys/_eventfilter.h"
in other header files (e.g., sys/{bus,conf,cpu}.h) and reduces header
pollution substantially.
EVENTHANDLER_DECLARE and EVENTHANDLER_LIST_DECLAREs were moved out of .c
files into appropriate headers (e.g., sys/proc.h, powernv/opal.h).
As a side effect of reduced header pollution, many .c files and headers no
longer contain needed definitions. The remainder of the patch addresses
adding appropriate includes to fix those files.
LOCK_DEBUG and LOCK_FILE_LINE_ARG are moved to sys/_lock.h, as required by
sys/mutex.h since r326106 (but silently protected by header pollution prior
to this change).
No functional change (intended). Of course, any out of tree modules that
relied on header pollution for sys/eventhandler.h, sys/lock.h, or
sys/mutex.h inclusion need to be fixed. __FreeBSD_version has been bumped.
SDIO command CMD53 (IO_RW_EXTENDED) allows data transfers using blocks of 1-2048 bytes,
with a maximum of 511 blocks per request.
Extend mmc_data structure to properly describe such requests,
and initialize the new fields in kernel and userland consumers.
No actual driver changes happen yet, these will follow in the separate changes.
Reviewed by: bz
Approved by: imp (mentor)
Differential Revision: https://reviews.freebsd.org/D19779
This is the common denominator for rockchip compatible from RK3288 to RK3399.
The other compatible are generally present in the DTS but the controllers
are the same.
MFC after: 1 week
transfer mode only (lost with r321385). [1]
- Similarly, don't try to set the power class on MMC devices that comply
to version 4.0 of the system specification but are operated in default/
legacy transfer or 1-bit bus mode as no power class is specified for
these cases. Trying to set a power class nevertheless resulted in an -
albeit harmless - error message.
PR: 231713 [1]
they don't check the result of BUS_READ_IVAR(9) and silently return stack
garbage on failure in case a bus doesn't implement a particular instance
variable for example. With MMC bridges not providing MMCBR_IVAR_RETUNE_REQ,
yet, this in turn can cause mmc(4) to get into a state in which re-tuning
seems to be necessary but is inappropriate, causing mmc_wait_for_request()
to fail. Thus, don't use __BUS_ACCESSOR() for mmcbr_get_retune_req() and
instead provide a version of the latter which returns retune_req_none if
reading MMCBR_IVAR_RETUNE_REQ fails.
One more straight-forward solution would have been to change mmc(4) to not
call mmcbr_get_retune_req() if the current transfer mode doesn't require
re-tuning to begin with. However, for modes such as SDR50, it depends on
the controller whether periodic re-tuning is need. Therefore, knowledge of
whether a particular transfer mode does require re-tuning should be kept
to the bridge drivers.
This change is the generic version of r338271, as intended not requiring
bridge drivers to be touched (unless transfer modes beyond high speed are
to be supported that is).
Approved by: re (gjb)
Since GENERIC includes quite a few drivers now, all MMC drivers should have
appropriate MMCCAM-related ifdefs and include opt_mmccam.h so that
those ifdefs are actually processed correctly.
Reviewed by: manu
Approved by: imp (mentor)
Differential Revision: https://reviews.freebsd.org/D15569
later devices. These caches work akin to the ones found in HDDs/SSDs
that ada(4)/da(4) also enable if existent, but likewise increase the
likelihood of data loss in case of a sudden power outage etc. On the
other hand, write performance is up to twice as high for e. g. 1 GiB
files depending on the actual chip and transfer mode employed.
For maximum data integrity, the usage of eMMC caches can be disabled
via the hw.mmcsd.cache tunable.
- Get rid of the NOP mmcsd_open().
* If compiled with EXT_RESOURCES look up the "biu" and "ciu" clocks in
the DT
* Don't use custom property "bus-frequency" but the standard one
"clock-frequency"
* Use the DT property max-frequency and fall back to 200Mhz if it don't exists
* Add more mmc caps suported by the controller
* Always ack all interrupts
* Subclassed driver can supply an update_ios so they can handle update
the clocks accordingly
* Take care of the DDR bit in update_ios (no functional change since we
do not support voltage change for now)
* Make use of the FDT bus-width property
