This helps with pkgbase by using CONFS and tagging these as config files.
Approved by: allanjude (mentor), des
Differential Revision: https://reviews.freebsd.org/D16678
This simplifies pkgbase by migrating these to CONFS so they are properly
tagged as config files.
Approved by: will (mentor)
Differential Revision: https://reviews.freebsd.org/D16708
This program is currently failing, and has been for >6 months on HEAD.
Ideally, this should be run 24x7 in CI, to discover hard-to-find bugs that
only manifest with concurrent i/o.
Requested by: lwhsu, mmacy
Ensure that the valid PCID state is created for proc0 pmap, since it
might be used by efirt enter() before first context switch on the BSP.
Sponsored by: The FreeBSD Foundation
MFC after: 6 days
The isonum_* functions are defined to take unsigend char* as an argument,
but the structure fields are defined as char. Change to u_char where needed.
Probably the full structure should be changed, but I'm not sure about the
side affects.
While there, add __packed attribute.
Differential Revision: https://reviews.freebsd.org/D16564
hashfilters. Two because the driver needs to look up a hashfilter by
its 4-tuple or tid.
A couple of fixes while here:
- Reject attempts to add duplicate hashfilters.
- Do not assume that any part of the 4-tuple that isn't specified is 0.
This makes it consistent with all other mandatory parameters that
already require explicit user input.
MFC after: 2 weeks
Sponsored by: Chelsio Communications
Remove the non-INTRNG code.
Remove left over cut and paste code from the lpc code that was the start for the port.
Set KERNPHYSADDR and KERNVIRTADDR
Tested on Buffalo_WZR2-G300N
Differential Revision: https://reviews.freebsd.org/D16622
While here pet mandoc and igor.
Reviewed by: bcr, eadler, krion, mat
Approved by: krion (mentor), mat (mentor)
Differential Revision: https://reviews.freebsd.org/D16376
WPA: Ignore unauthenticated encrypted EAPOL-Key data
Ignore unauthenticated encrypted EAPOL-Key data in supplicant
processing. When using WPA2, these are frames that have the Encrypted
flag set, but not the MIC flag.
When using WPA2, EAPOL-Key frames that had the Encrypted flag set but
not the MIC flag, had their data field decrypted without first verifying
the MIC. In case the data field was encrypted using RC4 (i.e., when
negotiating TKIP as the pairwise cipher), this meant that
unauthenticated but decrypted data would then be processed. An adversary
could abuse this as a decryption oracle to recover sensitive information
in the data field of EAPOL-Key messages (e.g., the group key).
(CVE-2018-14526)
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
Obtained from: git://w1.fi/hostap.git
MFC after: 1 day
Security: CVE-2018-14526
Security: VuXML: 6bedc863-9fbe-11e8-945f-206a8a720317
Ignore unauthenticated encrypted EAPOL-Key data in supplicant
processing. When using WPA2, these are frames that have the Encrypted
flag set, but not the MIC flag.
When using WPA2, EAPOL-Key frames that had the Encrypted flag set but
not the MIC flag, had their data field decrypted without first verifying
the MIC. In case the data field was encrypted using RC4 (i.e., when
negotiating TKIP as the pairwise cipher), this meant that
unauthenticated but decrypted data would then be processed. An adversary
could abuse this as a decryption oracle to recover sensitive information
in the data field of EAPOL-Key messages (e.g., the group key).
(CVE-2018-14526)
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
Obtained from: git://w1.fi/hostap.git
MFC after: 1 day
Security: CVE-2018-14526
Security: VuXML: 6bedc863-9fbe-11e8-945f-206a8a720317
A follow-up to r337812 to catch a couple more memory leaks that should
have been included in that change.
Reported by: Coverity
CID: 1296064, 1296067 (for real this time)
MFC after: 3 days
X-MFC-with: r337812
Sponsored by: Dell EMC
The libkqueue tests have several places that leak memory by using an
idiom like:
puts(kevent_to_str(kevp));
Rework to save the pointer returned from kevent_to_str() and then
free() it after it has been used.
Reported by: asomers (pointer to Coverity), Coverity
CID: 1296063, 1296064, 1296065, 1296066, 1296067, 1350287, 1394960
Sponsored by: Dell EMC
Create loader_{4th,lua,simp}{,.efi}. All of these are installed by
default. Create LOADER_DEFAULT_INTERP to specify the default
interpreter when no other is specified. LOADER_INTERP is the current
interpreter language building. Turn building of lua on by default to
match 4th. simploader is a simplified loader build w/o any interpreter
language (but with a simple loader). This is the historic behavir you
got with WITHOUT_FORTH. Make a hard link to the default loader. This
has to be a hard link rather than the more desirable soft link because
older zfsboot blocks don't support symlinks.
RelNotes: Yes
Differential Revision: https://reviews.freebsd.org/D16705
Previous iteration of this assumed that these won't fail because we've
already setup the jail param to this point, but the allocations could still
fail in pretty bad conditions.
Admit that it's possible and return (ENOENT, EINVAL, ENOMEM, or 0) when
deleting arguments. EINVAL shouldn't happen since we're passing optarg;
which may satisfy *optarg == '\0' but never optarg == NULL.
CID: 1394885, 1394901
Currently, the limits are quite high. On machines with millions of
mbuf clusters, the reassembly queue limits can also run into
the millions. Lower these values.
Also, try to ensure that no bucket will have a reassembly
queue larger than approximately 100 items. This limits the cost to
find the correct reassembly queue when processing an incoming
fragment.
Due to the low limits on each bucket's length, increase the size of
the hash table from 64 to 1024.
Reviewed by: jhb
Security: FreeBSD-SA-18:10.ip
Security: CVE-2018-6923
In particular, try to ensure that no bucket will have a reassembly
queue larger than approximately 100 items. This limits the cost to
find the correct reassembly queue when processing an incoming
fragment.
Due to the low limits on each bucket's length, increase the size of
the hash table from 64 to 1024.
Reviewed by: jhb
Security: FreeBSD-SA-18:10.ip
Security: CVE-2018-6923
On the guest entry in bhyve, flush L1 data cache, using either L1D
flush command MSR if available, or by reading enough uninteresting
data to fill whole cache.
Flush is automatically enabled on CPUs which do not report RDCL_NO,
and can be disabled with the hw.vmm.l1d_flush tunable/kenv.
Security: CVE-2018-3646
Reviewed by: emaste. jhb, Tony Luck <tony.luck@intel.com>
Sponsored by: The FreeBSD Foundation
Currently, we process IPv6 fragments with 0 bytes of payload, add them
to the reassembly queue, and do not recognize them as duplicating or
overlapping with adjacent 0-byte fragments. An attacker can exploit this
to create long fragment queues.
There is no legitimate reason for a fragment with no payload. However,
because IPv6 packets with an empty payload are acceptable, allow an
"atomic" fragment with no payload.
Reviewed by: jhb
Security: FreeBSD-SA-18:10.ip
Security: CVE-2018-6923
There is a hashing algorithm which should distribute IPv6 reassembly
queues across the available buckets in a relatively even way. However,
if there is a flaw in the hashing algorithm which allows a large number
of IPv6 fragment reassembly queues to end up in a single bucket, a per-
bucket limit could help mitigate the performance impact of this flaw.
Implement such a limit, with a default of twice the maximum number of
reassembly queues divided by the number of buckets. Recalculate the
limit any time the maximum number of reassembly queues changes.
However, allow the user to override the value using a sysctl
(net.inet6.ip6.maxfragbucketsize).
Reviewed by: jhb
Security: FreeBSD-SA-18:10.ip
Security: CVE-2018-6923
The IPv4 fragment reassembly code supports a limit on the number of
fragments per packet. The default limit is currently 17 fragments.
Among other things, this limit serves to limit the number of fragments
the code must parse when trying to reassembly a packet.
Add a limit to the IPv6 reassembly code. By default, limit a packet
to 65 fragments (64 on the queue, plus one final fragment to complete
the packet). This allows an average fragment size of 1,008 bytes, which
should be sufficient to hold a fragment. (Recall that the IPv6 minimum
MTU is 1280 bytes. Therefore, this configuration allows a full-size
IPv6 packet to be fragmented on a link with the minimum MTU and still
carry approximately 272 bytes of headers before the fragmented portion
of the packet.)
Users can adjust this limit using the net.inet6.ip6.maxfragsperpacket
sysctl.
Reviewed by: jhb
Security: FreeBSD-SA-18:10.ip
Security: CVE-2018-6923
The IPv6 reassembly fragment limit is based on the number of mbuf clusters,
which are a global resource. However, the limit is currently applied
on a per-VNET basis. Given enough VNETs (or given sufficient customization
on enough VNETs), it is possible that the sum of all the VNET fragment
limits will exceed the number of mbuf clusters available in the system.
Given the fact that the fragment limits are intended (at least in part) to
regulate access to a global resource, the IPv6 fragment limit should
be applied on a global basis.
Note that it is still possible to disable fragmentation for a particular
VNET by setting the net.inet6.ip6.maxfragpackets sysctl to 0 for that
VNET. In addition, it is now possible to disable fragmentation globally
by setting the net.inet6.ip6.maxfrags sysctl to 0.
Reviewed by: jhb
Security: FreeBSD-SA-18:10.ip
Security: CVE-2018-6923
There is a hashing algorithm which should distribute IPv4 reassembly
queues across the available buckets in a relatively even way. However,
if there is a flaw in the hashing algorithm which allows a large number
of IPv4 fragment reassembly queues to end up in a single bucket, a per-
bucket limit could help mitigate the performance impact of this flaw.
Implement such a limit, with a default of twice the maximum number of
reassembly queues divided by the number of buckets. Recalculate the
limit any time the maximum number of reassembly queues changes.
However, allow the user to override the value using a sysctl
(net.inet.ip.maxfragbucketsize).
Reviewed by: jhb
Security: FreeBSD-SA-18:10.ip
Security: CVE-2018-6923
The IP reassembly fragment limit is based on the number of mbuf clusters,
which are a global resource. However, the limit is currently applied
on a per-VNET basis. Given enough VNETs (or given sufficient customization
of enough VNETs), it is possible that the sum of all the VNET limits
will exceed the number of mbuf clusters available in the system.
Given the fact that the fragment limit is intended (at least in part) to
regulate access to a global resource, the fragment limit should
be applied on a global basis.
VNET-specific limits can be adjusted by modifying the
net.inet.ip.maxfragpackets and net.inet.ip.maxfragsperpacket
sysctls.
To disable fragment reassembly globally, set net.inet.ip.maxfrags to 0.
To disable fragment reassembly for a particular VNET, set
net.inet.ip.maxfragpackets to 0.
Reviewed by: jhb
Security: FreeBSD-SA-18:10.ip
Security: CVE-2018-6923
