USB ethernet chip. Adapters that use this chip include the LinkSys
USB100TX. There are a few others, but I'm not certain of their
availability in the U.S. I used an ADMtek eval board for development.
Note that while the ADMtek chip is a 100Mbps device, you can't really
get 100Mbps speeds over USB. Regardless, this driver uses miibus to
allow speed and duplex mode selection as well as autonegotiation.
Building and kldloading the driver as a module is also supported.
Note that in order to make this driver work, I had to make what some
may consider an ugly hack to sys/dev/usb/usbdi.c. The usbd_transfer()
function will use tsleep() for synchronous transfers that don't complete
right away. This is a problem since there are times when we need to
do sync transfers from an interrupt context (i.e. when reading registers
from the MAC via the control endpoint), where tsleep() us a no-no.
My hack allows the driver to have the code poll for transfer completion
subject to the xfer->timeout timeout rather that calling tsleep().
This hack is controlled by a quirk entry and is only enabled for the
ADMtek device.
Now, I'm sure there are a few of you out there ready to jump on me
and suggest some other approach that doesn't involve a busy wait. The
only solution that might work is to handle the interrupts in a kernel
thread, where you may have something resembling a process context that
makes it okay to tsleep(). This is lovely, except we don't have any
mechanism like that now, and I'm not about to implement such a thing
myself since it's beyond the scope of driver development. (Translation:
I'll be damned if I know how to do it.) If FreeBSD ever aquires such
a mechanism, I'll be glad to revisit the driver to take advantage of
it. In the meantime, I settled for what I perceived to be the solution
that involved the least amount of code changes. In general, the hit
is pretty light.
Also note that my only USB test box has a UHCI controller: I haven't
I don't have a machine with an OHCI controller available.
Highlights:
- Updated usb_quirks.* to add UQ_NO_TSLEEP quirk for ADMtek part.
- Updated usbdevs and regenerated generated files
- Updated HARDWARE.TXT and RELNOTES.TXT files
- Updated sysinstall/device.c and userconfig.c
- Updated kernel configs -- device aue0 is commented out by default
- Updated /sys/conf/files
- Added new kld module directory
pr_input() routines prototype is also changed to support IPSEC and IPV6
chained protocol headers.
Reviewed by: freebsd-arch, cvs-committers
Obtained from: KAME project
3.3R and then to -current. The pccard support has been left in the
driver, but is presently non-functional because we are using the
isa_compat layer for the moment.
Obtained From: PAO
Sponsored by: Timing Solutions
These drivers were cloned from the ed and ep drivers back in 1994
when PCMCIA cards were a very new thing and we had no other support
for such devices. They treated the PCIC (the chip which controls the
PCCARD slot) as part of their device and generally hacked their way
to success. They have significantly bit-rotted relative to their
ancestor drivers (ed & ep) and they were a dead-end on the evolution
path to proper PCCARD support in FreeBSD.
They have been terminally broken since August 18 where mdodd forgot
them and nobody seems to have missed them enough to fix them since.
I found no outstanding PRs against these drivers.
packet divert at kernel for IPv6/IPv4 translater daemon
This includes queue related patch submitted by jburkhol@home.com.
Submitted by: queue related patch from jburkhol@home.com
Reviewed by: freebsd-arch, cvs-committers
Obtained from: KAME project
which it replaces. The new driver supports all of the chips supported
by the ones it replaces, as well as many DEC/Intel 21143 10/100 cards.
This also completes my quest to convert things to miibus and add
Alpha support.
mention of the various devices that are supported.
Add some text and entry to LINT for 'controller mca0'.
I'd like to turn this option on in GENERIC as well as it
isn't impacting and has a small footprint.
* Bring source file references in line with the style used in
GENERIC (i.e. src/sys/...).
* Update outdated source file references.
* Use proper URL syntax for URLs.
* Update outdated URLs.
PR: 15194
Submitted by: jedgar@fxp.org (Chris D. Faulhaber)
Add MD_ROOT and MD_ROOT_SIZE options to the md driver.
Make the md driver handle MFS_ROOT and MFS_ROOT_SIZE options for compatibility.
Add md driver to GENERIC, PCCARD and LINT.
This is a cleanup which removes the need for some of the worse hacks in
MFS: We really want to have a rootvnode but MFS on a preloaded image
doesn't really have one. md is a true device, so it is less trouble.
This has been tested with make release, and if people remember to add
the "md" pseudo-device to their kernels, PicoBSD should be just fine
as well. If people have no other use for MFS, it can be removed from
the kernel.
- Convert to new bus attachment scheme. Thanks to Blaz Zupan for doing
the initial work here. One thing I changed was to have the attach
and detach routines work like the PCI drivers, which means that in
theory you should be able to load and unload the driver like the PCI
NIC drivers, however the pccard support for this hasn't settled down
yet so it doesn't quite work. Once the pccard work is done, I'll have
to revisit this.
- Add device wi0 to PCCARD. If we're lucky, people should be able to
install via their WaveLAN cards now.
- Add support for signal strength caching. The wicontrol utility has
also been updated to allow zeroing and displaying the signal strength
cache.
- Add a /sys/modules/wi directory and fix a Makefile to builf if_wi.ko.
Currently this module is only built for the i386 platform, though once
the pccard stuff is done it should be able to work on the alpha too.
(Theoretically you should be able to plug one of the WaveLAN/IEEE ISA
cards into an alpha with an ISA slot, but we'll see how that turns out.
- Update LINT to use only device wi0. There is no true ISA version of
the WaveLAN/IEEE so we'll never use an ISA attachment.
- Update files.i386 so that if_wi is dependent on card.
Document the options available for the ata driver.
Disconnect the atapi devices from the old wd driver to avoid conflicts
(they will go away at some point anyways)
* GC unused options
* Move options that exist on all architectures to conf/options
* Add missing options to LINT
* Sort undocumented options list in LINT
Reviewed by: green
to config(8) for static device tables that have not existed for quite
some time. They have been aliases for 'device' for a while, and "tape"
went away entirely as it wasn't used anywhere (except in an example
in LINT.. "fixed").
o Gut the compatibility interface, you now must attach with newbus.
o Unit numbers from pccardd are now ignored. This may change the units
assigned to a card. It now uses the first available unit.
o kill old skeleton code that is now obsolete.
o Use newbus attachment code.
o cleanup interfile dependencies some.
o kill list of devices per slot. we use the device tree for what we need.
o Remove now obsolete code.
o The ep driver (and maybe ed) may need some config file tweaks to
allow it to attach. See config files that were committed for examples
on how to do this.
Drivers to be commited shortly.
This is an interrum fix until the new pccard. ed, ep and sio will be
supported by me with this release, although others are welcome to try
to support other devices before new pccard is working.
I plan on doing minimal further work on this code base. Be careful
when upgrading, since this code is known to work on my laptop and
those of a couple others as well, but your milage may vary.
BUGS TO BE FIXED:
o system memory isn't allocated yet, it will be soon.
o No devices actually have a pccard newbus attach in the tree.
BUGS THAT MIGHT BE FIXED:
o card removal, including suspend, usually hangs the system.
Many thanks to Peter Wemm and Doug Rabson for helping me to fill in
the missing bits of New Bus understanding at FreeBSD Con '99.
Been in production for 3 years now. Gives Instant Frame relay to if_sr
and if_ar drivers, and PPPOE support soon. See:
ftp://ftp.whistle.com/pub/archie/netgraph/index.html
for on-line manual pages.
Reviewed by: Doug Rabson (dfr@freebsd.org)
Obtained from: Whistle CVS tree
floating before). Attach pccard devices to pcic, one per slot
(although this may change to one per pcic). pcic is now attached to
isa (to act as a bridge) and pccard is attached to pcic, cbb and
pc98ic (the last two are card bus bridge and the pc98ic version of
pcic, neither of which are in the tree yet). Move pccard compat code
into pccard/pccard_compat.c.
THIS REQUIRES A CONFIG FILE CHANGE. You must change your pcic/card
entries to be:
# PCCARD (PCMCIA) support
controller pcic0 at isa?
controller pcic1 at isa?
controller card0
The old system was upside down and this corrects that problem. It
will make it easier to add support for YENTA pccard/card bus bridges.
Much more cleanup needs to happen before newbus devices can have
pccard attachments. My previous commit's comments were premature.
