Compile and link a new kernel, that will give native ELF support, and
provide the hooks for other ELF interpreters as well.
To make native ELF binaries use John Polstras elf-kit-1.0.1..
For the time being also use his ld-elf.so.1 and put it in
/usr/libexec.
The Linux emulator has been enhanced to also run ELF binaries, it
is however in its very first incarnation.
Just get some Linux ELF libs (Slackware-3.0) and put them in the
prober place (/compat/linux/...).
I've ben able to run all the Slackware-3.0 binaries I've tried
so far.
(No it won't run quake yet :)
"foo", what this does is:
(1) Put all distfiles and patchfiles in /usr/ports/distfiles/foo
(2) Go to ftp://ftp.freebsd.org/pub/FreeBSD/distfiles/foo when the
master site is down
When your port has a lot of dist/patchfiles, or has a file that does
not have a very port-specific name (e.g., "Makefile"), set this
variable instead of redefining DISTDIR. (If you redefine DISTDIR, (1)
will work but (2) will not.)
Agreed that it's a good idea by: adam
Cleanse the SCSI subsystem of its internally defined types
u_int32, u_int16, u_int8, int32, int16, int8.
Use the system defined *_t types instead.
aic7870.c:
Handle Seeprom data a little better.
Cleanse the SCSI subsystem of its internally defined types
u_int32, u_int16, u_int8, int32, int16, int8.
Use the system defined *_t types instead.
aic7xxx.c:
Fix the reset code.
Instead of queing up all of the SCBs that timeout during timeout
processing, we take the first and have it champion the effort.
Any other scbs that timeout during timeout handling are given
another lifetime to complete in the hopes that once timeout
handing is finished, they will complete normally. If one of
these SCBs times out a second time, we panic and Justin tries
again.
The other major change is to queue flag aborted SCBs during timeout
handling, and "ahc_done" them all at once as soon as we have the
controller back into a sane state. Calling ahc_done any earlier
will cause the SCSI subsystem to toss the command right back at
us and the attempt to queue the command will conflict with what
the timeout routine is trying to accomplish.
The aic7xxx driver will now respond to bus resets initiated by
other devices.
Cleanse the SCSI subsystem of its internally defined types
u_int32, u_int16, u_int8, int32, int16, int8.
Use the system defined *_t types instead.
eisaconf.c:
Cosmetic formatting chagnes.
device file and the mount point. This prevents the "unexpected recursive
lock" panic from happening.
This is a temporary fix. A kernel fix would be much much more ugly than
this, and still wouldn't be the "right" way to fix it. After some
of Terry's file system rework is installed, it will be possible to
properly fix this problem in a clean manner. Until then,
this change should prevent use from getting a problem report
on this every month or so (and I just noticed that someone in
one of the freebsd news groups was complaining about this problem, too).
remote peer will be connected through. This avoids the ``Checking for
invitation on caller's machine'' problem for multi-homed hosts.
Thanks to: Garrett, for his `find_interface' example
iterations of 30uS so that really fast systems stop getting
timeout messages from the Riscom driver.
Reviewed by: ache, peter@nmti.com (Peter da Silva)
*not* our controlling terminal (SIGHUP can coming in other case)
2) Add HUPCL for non-dedicated lines to be shure that modem
properly resetted.
3) Correct usage string.
handled correctly. Fix some incorrect code that was included
to improve performance. Significantly simplify the pmap_use_pt and
pmap_unuse_pt subroutines. Add some more diagnostic code.
The pmap_remove in vm_map_clean incorrectly unmapped the entire
map entry.
The new vm_map_simplify_entry code had an error (the offset
of the combined map entry was not set correctly.)
Submitted by: Alan Cox <alc@cs.rice.edu>
residing in a buffer that had been dirtied by a process was being
handled incorrectly. The pages were mistakenly placed into the
cache queue. This would likely have the effect of mmaped page modifications
being lost when I/O system calls were being used simultaneously to
the same locations in a file.
Submitted by: davidg
Story so fr:
1) PPP on-demand with static IP works.
2) PPP on-demand with dynamic IP says "Host is down" on any IP request
The problem is that tun driver check its READY state by *first* ifconfig address.
i.e.:
set ifaddr <addr> <addr2>
works (static IP) and
set ifaddr 0 <addr2>
not works (dynamic IP) because first address is equal 0.
Since tun is always POINTOPOINT interface, dst address is more meaningfull.
I change checking to second (dst) address in READY test.
PPP on-demand finally works.
2) Improve on-line help subsystem
3) Make 'term' mode works even carrier dropped (old code
close line forever here)
4) Make 'term' mode 8bit clean.
5) Improve manual page
6) #ifdef DEBUG diagnostic about missing optional files.
7) Don't put interactive dialing info to logfile
is defined and FORCE_COMCONSOLE isn't defined.
Don't compile any keyboard probing code if PROBE_KEYBOARD isn't defined.
Makefile:
Removed -I paths. They weren't used, and the one to /sys hasn't worked
since the source directory was moved down one level.
counter instead of the BIOS time call to save space.
Reworked the anti-noise timeout to avoid duplicating code. The timeout
in the outer loop is now restarted after every noise timeout, so it is
now possible for the total timeout to be infinite; previously, the maximum
total timeout was 150000 seconds.
must have limit 0xffff and attribute G = 0 (byte granularity) as well
as other properties that they already had (see e.g., the Intel i486
manual section 22.5). Not restoring them broke Ctrl-Alt-Del in the
bootstrap for my ASUS P55TP4XE system, probably because the Award BIOS
does anti-tracing stuff involving inaccessible %esp's.
asm.S:
Don't use lret in prot_to_real(). This reduces the risk of using an
incompletely intialized stack segment and saves space.
Submitted by: "K.Higashino" <a00303@cc.hc.keio.ac.jp> (on 13 Jan 1995!)
reworked by me
since I've no idea what the ISO standard for Italian keyboards is, but we
can always adjust it later and this is better than the nothing we had before.
Submitted by: Gianmarco Giovannelli <gmarco@masternet.it>
