The RSB controller speaks a simplified two wire protocol at speeds up to
20MHz. It is used on sun8i and sun9i family SoCs to communicate with
power management ICs.
RSB isn't really I2C or SMBus, but the driver exposes an iicbus interface
to simplify power management IC drivers (which may need to support both
RSB and I2C connectivity).
This function works with all smp non-multicluster allwinner SoC (A20, A31, A31S and H3).
Approved by: cognet (mentor)
Differential Revision: https://reviews.freebsd.org/D6269
struct associated with some type defined in enum intr_map_data_type
must have struct intr_map_data on the top of its own definition now.
When such structs are used, correct type and size must be filled in.
There are three such structs defined in sys/intr.h now. Their
definitions should be moved to corresponding headers by follow-up
commits.
While this change was propagated to all INTRNG like PICs,
pic_map_intr() method implementations were corrected on some places.
For this specific method, it's ensured by a caller that the 'data'
argument passed to this method is never NULL. Also, the return error
values were standardized there.
Clocks, GPIO, UART, SD card / eMMC, USB, watchdog, and ethernet are
supported. Note that the A83T contains two clusters of four Cortex-A7
CPUs, and only CPUs in first cluster are started for now.
Tested on a Sinovoip Banana Pi BPI-M3.
The datasheets refer to this controller as EMAC, not to be confused with
the fast ethernet controller (also named EMAC) found in A10/A20 SoCs.
Tested on a BananaPi M3 (A83T), which uses an external RGMII PHY (RTL8211E).
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D6169
implementations. Early in the boot the kernel will use an approximate,
however after the timer has been probed it will switch to a more accurate
implementation.
Reviewed by: manu
Sponsored by: ABT Systems Ltd
Differential Revision: https://reviews.freebsd.org/D5762
Set MMC_CAP_4_BIT_DATA and MMC_CAP_8_BIT_DATA based on the "bus-width"
DT property and reduce maximum bus frequency from 52MHz to 50MHz to match
the capabilities of the clock provider.
Tested on a BananaPi BPI-M3 (A83T).
a DRIVER_MODULE() referencing mmc_driver has a MODULE_DEPEND() on mmc. This
is because the kernel linker only searches for symbols in dependent modules,
so loading sdhci_pci (and other bus-flavors of sdhci) would fail when mmc
was not compiled into the kernel (even if you hand-loaded mmc first).
(Thanks to jilles@ for providing the vital clue about the kernel linker.)
code for the A20 to use the new PLATFORM_SMP interface, and extends it to
add support for the new SoCs allowing for both to coexist within the same
kernel.
Submitted by: Emmanuel Vadot <manu@bidouilliste.com>
Reviewed by: jmcneill
Differential Revision: https://reviews.freebsd.org/D5342
adds a lock to ensure only a single device is accessing the hardware. A
reference count is added to only enable when we start to use the clock,
and to disable after we have finished needing the clock.
This was extracted from a larger review to add OHCI support to the
Allwinner SoCs.
Submitted by: Emmanuel Vadot <manu@bidouilliste.com>
Reviewed by: jmcneill
X-Differential Revision: https://reviews.freebsd.org/D5481
Very similar to the A10 RTC controller with a few register offsets changed
and a different location for the LOSC switch status.
Submitted by: Emmanuel Vadot <manu@bidouilliste.com>
Reviewed by: jmcneill
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D5500
Newer Allwinner MMC implementations use a different FIFO register offset
(0x200 instead of 0x100). Since the FDT uses the same compat string for
both cases, base the decision on which FIFO offset to use on the Allwinner
SoC family.
Reviewed by: Emmanuel Vadot <manu@bidouilliste.com>
Approved by: gonzo (mentor)
Differential Revision: https://reviews.freebsd.org/D5468
intr_pic_init_secondary. Replace them with a direct call. On BCM2836
and ARMADA XP we need to add this function, but it can be empty.
Reviewed by: ian, imp
Sponsored by: ABT Systems Ltd
Differential Revision: https://reviews.freebsd.org/D5460
slightly wrong on the others. We should just check if mp_ncpus is set to
more than one CPU as we may wish to run on a single core even when SMP is
available.
Reviewed by: ian
Sponsored by: ABT Systems Ltd
Differential Revision: https://reviews.freebsd.org/D5458
support for the i2c, mmc, and gmac clocks. Further clocks can be added as
needed.
Submitted by: Emmanuel Vadot <manu@bidouilliste.com>
Reviewed by: jmcneill
Differential Revision: https://reviews.freebsd.org/D5339
The HDMI driver will attach a framebuffer device when a display is
connected. If the EDID can be read and contains a preferred mode, it
will be used. Otherwise the framebuffer will default to 800x600.
In addition, if the EDID contains a CEA-861 extension block and the
"basic audio" flag is set, audio playback at 48kHz 16-bit stereo is
enabled on the controller.
Reviewed by: andrew
Approved by: gonzo (mentor)
Differential Revision: https://reviews.freebsd.org/D5383
driver. This mostly involves selecting the register offsets to use at
runtime based on the hardware we are talking to.
Submitted by: Emmanuel Vadot <manu@bidouilliste.com>
Differential Revision: https://reviews.freebsd.org/D5327
will be needed when we bring in further support for these SoCs.
Submitted by: Emmanuel Vadot <manu@bidouilliste.com>
Differential Revision: https://reviews.freebsd.org/D5340
For sources and destinations marked "noincr", the previous code was
incorrectly programming the dedicated DMA channel control register
using bit definitions for normal DMA channels. This code path is not
currently used, but will be used by the HDMI audio driver in review.
Reviewed by: andrew
Approved by: gonzo (mentor)
Differential Revision: https://reviews.freebsd.org/D5382
Only L2 PIPT cache is supported for __ARM_ARCH >= 6.
In fact, this is just a pure proclamation as this option is used
only in armv4 specific files now.
FDT platform code to detect when we are booting on one of these SoCs. The
driver changes will be added shortly.
Submitted by: Emmanuel Vadot <manu@bidouilliste.com>
Differential Revision: https://reviews.freebsd.org/D5338
configuration from the FDT data, then set the pins into the requested
state. As part of this the gpio controller now reports the correct number
of pins instead of returning the number of bank * 32.
To allow for a future consolidated kernel we add the SOC_ALLWINNER_A10 and
SOC_ALLWINNER_A20 kernel options. These need to be set as appropriate for
the SoC the kernel will boot on.
Submitted by: Emmanuel Vadot <manu@bidouilliste.com>
Differential Revision: https://reviews.freebsd.org/D5177
