This uses the new firmware(9) method for squirreling away the EEPROM
contents from SPI flash so ath(4) can get to them later.
It won't work out of the box just yet - you have to add this to
if_ath_pci.c:
#define ATH_EEPROM_FIRMWARE
.. until I've added it as a configuration option and updated things.
future use by the ath(4) driver.
These embedded devices put the calibration/PCI bootstrap data on the
on board SPI flash rather than on an EEPROM connected to the NIC.
For some boards, there's two NICs and two sets of EEPROM data in the
main SPI flash.
The particulars:
* Introduce ath_fixup_size, which is the size of the EEPROM area in
bytes.
* Create a firmware image with a name based on the PCI device identifier
(bus/slot/device/function).
* Hide some verbose debugging behind 'bootverbose'.
ath(4) can then use this to load in the EEPROM data.
This requires AR71XX_ATH_EEPROM to be defined.
* the openwrt code doesn't treat 0/0/0 any differently
from other bus/slot/func combinations.
* A "local write" function writes to the LCONF area, and
so I've added it.
* The PCI workaround at attach time uses this LCONF code,
which it already did ..
* .. but it is a 4 byte write, not a 2 byte write.
Even though it's PCIR_COMMAND which is a two byte PCI register.
Tested on: AR7161
TODO: The other two AR71xx derivatives
TODO: More thoroughly stare at the datasheets I do have
and if it indeed is incorrect, push fixes to both
FreeBSD and Linux/OpenWRT.
Obtained from: Linux OpenWRT
This makes our naming scheme more closely match other systems and the
expectations of much third-party software. MIPS builds which are little-endian
should require and exhibit no changes. Big-endian TARGET_ARCHes must be
changed:
From: To:
mipseb mips
mipsn32eb mipsn32
mips64eb mips64
An entry has been added to UPDATING and some foot-shooting protection (complete
with warnings which should become errors in the near future) to the top-level
base system Makefile.
New kernel events can be added at various location for sampling or counting.
This will for example allow easy system profiling whatever the processor is
with known tools like pmcstat(8).
Simultaneous usage of software PMC and hardware PMC is possible, for example
looking at the lock acquire failure, page fault while sampling on
instructions.
Sponsored by: NETASQ
MFC after: 1 month
The on-chip SD slots do not have PCI BARs corresponding to them, so
this has to be handled in the custom SoC memory allocation.
Provide memory resource for rids corresponding to BAR 0 and 1 in
the custom allocation code.
The XLP on-chip devices have PCI configuration headers, but some of the
devices need custom resource allocation code.
- devices with no MEM/IO BARs with registers in PCIe extended reg
space have to be handled in memory resource allocation
- devices without INTPIN/INTLINE in PCI header can be supported
by having these faked with a shadow register.
- Some devices does not allow 8/16 bit access to the register space,
he default bus space cannot be used for these.
Subclass pci and override attach and resource allocation methods to
take care of this.
Remove earlier code which did this partially.
Move XLP PCI UART device to sys/mips/nlm/dev/ directory. Other
drivers for the XLP SoC devices will be added here as well.
Update uart_cpu_xlp.c and uart_pci_xlp.c use macros for uart port,
speed and IO frequency.
Features:
- network driver for the four 10G interfaces and two management ports
on XLP 8xx.
- Support 4xx and 3xx variants of the processor.
- Source code and firmware building for the 16 mips32r2 micro-code engines
in the Network Accelerator.
- Basic initialization code for Packet ordering Engine.
Submitted by: Prabhath Raman (prabhath at netlogicmicro com)
[refactored and fixed up for style by jchandra]
On XLP evaluation platform, the board information is stored
in an I2C eeprom and the network block configuration is available
from a CPLD connected to the GBU (NOR flash bus). Add support
for both of these.
Support for the Security and RSA blocks on XLP SoC. Even though
the XLP supports many more algorithms, only the ones supported
in OCF have been added.
Submitted by: Venkatesh J. V. (venkatesh at netlogicmicro com)
- XLP supports hardware swap for PCIe IO/MEM accesses. Since we
are in big-endian mode, enable hardware swap and use the normal
bus space.
- move some printfs to bootverbose, and remove others.
- fix SoC device resource allocation code
- Do not use '|' while updating PCIE_BRIDGE_MSI_ADDRL
- some style fixes
In collaboration with: Venkatesh J. V. (venkatesh at netlogicmicro com)
- Replace MIPS24K-specific code with more generic framework that will
make adding new CPU support easier
- Add MIPS24K support for new framework
- Limit backtrace depth to 1 for stability reasons and add option
HWPMC_MIPS_BACKTRACE to override this limitation
As of FreeBSD 8, this driver should not be used. Applications that use
posix_openpt(2) and openpty(3) use the pts(4) that is built into the
kernel unconditionally. If it turns out high profile depend on the
pty(4) module anyway, I'd rather get those fixed. So please report any
issues to me.
The pty(4) module is still available as a kernel module of course, so a
simple `kldload pty' can be used to run old-style pseudo-terminals.
These are needed for some particular port configurations where the default
speed isn't suitable for all link speed types. (Ie, changing 10/100/1000MBit
PLL rate requires a similar MII clock rate, rather than a fixed MII rate.)
This is:
* only currently implemented for the ar71xx;
* isn't used anywhere (yet), as the final interface for this hasn't yet
been determined.
function.
From the submitter:
This patch fixes an issue I encountered using an NFS root with an
ar71xx-based MikroTik RouterBoard 450G on -current where the kernel fails
to contact a DHCP/BOOTP server via if_arge when it otherwise should be able
to. This may be the same issue that Monthadar Al Jaberi reported against
an RSPRO on 6 March, as the signature is the same:
%%%
DHCP/BOOTP timeout for server 255.255.255.255
DHCP/BOOTP timeout for server 255.255.255.255
DHCP/BOOTP timeout for server 255.255.255.255
.
.
.
DHCP/BOOTP timeout for server 255.255.255.255
DHCP/BOOTP timeout for server 255.255.255.255
arge0: initialization failed: no memory for rx buffers
DHCP/BOOTP timeout for server 255.255.255.255
arge0: initialization failed: no memory for rx buffers
%%%
The primary issue that I found is that the DHCP/BOOTP message that
bootpc_call() is sending never makes it onto the wire, which I believe is
due to the following:
- Last December, a change was made to the ifioctl that bootpc_call() uses
to adjust the netmask around the sosend().
- The new ioctl (SIOCAIFADDR) performs an if_init when invoked, whereas the
old one (SIOCSIFNETMASK) did not.
- if_arge maintains its own sense of link state in sc->arge_link_status.
- On a single-phy interface, sc->arge_link_status is initialized to 0 in
arge_init_locked().
- sc->arge_link_status remains 0 until a phy state change notification
causes arge_link_task to run, notice the link is up, and set it to 1.
- The inits caused by the ifioctls in bootpc_call are reinitializing the
interface, but not the phy, so sc->arge_link_status goes to 0 and remains
there.
- arge_start_locked() always sees sc->arge_link_status == 0 and returns
without queuing anything.
The attached patch changes arge_init_locked() such that in the single-phy
case, instead of initializing sc->arge_link_status to 0, it runs
arge_link_task() to set it according to the current phy state. This change
has allowed my setup to mount an NFS root successfully.
Submitted by: Patrick Kelsey <kelsey@ieee.org>
Reviewed by: juli
I had some interesting hangs until I realised I should try flushing the
DDR FIFO register and lo and behold, hangs stopped occuring.
I've put in a few DDR flushes here and there in case people decide to
reuse some of these functions. It's very very likely they're almost
all superflous.
To test:
* Connect to a network with a _lot_ of broadcast traffic
* Do this:
# while true; do ifconfig arge0 down; ifconfig arge0 up; done
This fixes the mbuf exhaustion that has been reported when the interface
state flaps up/down.
required for the ABI the kernel is being built for.
XXX This is implemented in a kind-of nasty way that involves including source
files, but it's still an improvement.
o) Retire ISA_* options since they're unused and were always wrong.
* enable ALQ and net80211/ath ALQ logging by default, to make it possible
to get debug register traces.
* Update some comments
* Enable HWPMC for testing.
implementations or no implementation on all platforms.
Some of these functions might be good ideas, but their semantics were unclear
given the lack of implementation, and an unlucky porter could be fooled into
trying to implement them or, worse, being baffled when something like
platform_trap_enter() failed to be called.
- Pass interrupt trapframe for handlers dow the chain
- Add PMC interrupt handler
PMC interrupt is a special case, so we want handle it as soon as possible
with minimum overhead. So we handle it apb filter routine.
bootable image.
The kernel has to fit inside an 896KiB area in a 4MB SPI flash.
So a bunch of stuff can't be included (and more is to come), including
(unfortunately) IPv6.
TODO:
* GPIO modules need to be created
* Shrink the image a bit more by removing some of the CAM layer debugging
strings.
make use of it where possible.
This primarily brings in support for newer hardware, and FreeBSD is not yet
able to support the abundance of IRQs on new hardware and many features in the
Ethernet driver.
Because of the changes to IRQs in the Simple Executive, we have to maintain our
own list of Octeon IRQs now, which probably can be pared-down and be specific
to the CIU interrupt unit soon, and when other interrupt mechanisms are added
they can maintain their own definitions.
Remove unmasking of interrupts from within the UART device now that the
function used is no longer present in the Simple Executive. The unmasking
seems to have been gratuitous as this is more properly handled by the buses
above the UART device, and seems to work on that basis.
o) The MAC set must occur before the multicast list is set up as the former
will enable the CAM unconditionally, while promiscuous mode disables it,
so if promiscuous mode is to be set this must occur after the MAC is
programmed.
o) The multicast list must be set up unconditionally as even if flags have
not changed, if the interface has gone through a reinitialization, the
state of the CAM as changed by the MAC initialization could be incorrect.
o) Call octm_init when flags change, even if the interface is already running.
XXX It would be good to use a better way to size intrcnt.
o) Fix literal 4s that are supposed to be sizeof (u_long).
XXX Why the * 2 here? Is this an artifact of a different system that this
code came from? We seem to allocate twice as much space for intrcnt
as we admit to in sintrcnt.
platforms.
This will make every attempt to mount a non-mpsafe filesystem to the
kernel forbidden, unless it is expressely compiled with
VFS_ALLOW_NONMPSAFE option.
This patch is part of the effort of killing non-MPSAFE filesystems
from the tree.
No MFC is expected for this patch.
o) Get rid of some unused macros related to features we don't intend to
provide.
o) Get rid of macro definitions for MIPS-I CPUs. We are not likely to
support anything that predartes MIPS-III.
o) Respell MIPS3_* macros as MIPS_*, which is how most of them were being
used already.
o) Eliminate a duplicate and mostly-unused set of exception vector macros.
There's still considerable duplication and lots more obsolete in our headers,
but this reduces one of the larger files to a size where one could reckon
about the correctness of its contents with a mere few hours of contemplation.
There is, of course, a question of whether we need definitions for fields,
registers and configurations that we are unlikely to ever use or implement,
even if they're not obsolete since 1991. FreeBSD is not a processor
reference manual, and things that aren't used may be wrong, or may be
duplicated because nobody could possibly actually know whether they're
already defined.
the native sigreturn doesn't use set_mcontext like the COMPAT_FREEBSD32 version
does, this wouldn't actually result in overwriting the TLS base. Probably it
makes sense to restructure the native sigreturn to use set_mcontext for
consistency, and to allow sigreturn to change the TLS base.
TLS:
o) The mc_tls field used to store the TLS base when doing context gets and
restores was left a pointer and not converted to a 32-bit integer. This
had the bug of not correctly capturing the TLS value desired by the user,
and the extra nastiness of making the structure the wrong size.
o) The mc_tls field was not being saved by sendsig. As a result, the TLS base
would always be set to NULL when restoring from a signal handler.
Thanks to gonzo for helping track down a bunch of other TLS bugs that came out
of tracking these down.
and offset it only if requested by RDHWR handler. Otherwise things
get overly complicated - we need to track whether address passsed in
request for setting td_md.md_tls is already offseted or not.
version was missing an else and would always use the n64 TP_OFFSET. Eliminate
some duplication of logic here.
It may be worth getting rid of some of the ifdefs and introducing gratuitous
SV_ILP32 runtime checks on n64 kernels without COMPAT_FREEBSD32 and on o32
kernels, similarly to how PowerPC works.
using the o32 ABI. This mostly follows nwhitehorn's lead in implementing
COMPAT_FREEBSD32 on powerpc64.
o) Add a new type to the freebsd32 compat layer, time32_t, which is time_t in the
32-bit ABI being used. Since the MIPS port is relatively-new, even the 32-bit
ABIs use a 64-bit time_t.
o) Because time{spec,val}32 has the same size and layout as time{spec,val} on MIPS
with 32-bit compatibility, then, disable some code which assumes otherwise
wrongly when built for MIPS. A more general macro to check in this case would
seem like a good idea eventually. If someone adds support for using n32
userland with n64 kernels on MIPS, then they will have to add a variety of
flags related to each piece of the ABI that can vary. That's probably the
right time to generalize further.
o) Add MIPS to the list of architectures which use PAD64_REQUIRED in the
freebsd32 compat code. Probably this should be generalized at some point.
Reviewed by: gonzo
handle address, where we're using handles as raw addresses.
This fixes devices with subregions on Octeon PCI specifically, and likely also on
MIPS more generally, where there isn't another bus_space in use that was doing the
math already.
long for specifying a boundary constraint.
- Change bus_dma tags to use bus_addr_t instead of bus_size_t for boundary
constraints.
These allow boundary constraints to be fully expressed for cases where
sizeof(bus_addr_t) != sizeof(bus_size_t). Specifically, it allows a
driver to properly specify a 4GB boundary in a PAE kernel.
Note that this cannot be safely MFC'd without a lot of compat shims due
to KBI changes, so I do not intend to merge it.
Reviewed by: scottl
- Reserver respective number of addresses for managment port
- octm uses base address directly
- other drivers get MACs on "first come first served" basis
Reviewed by: juli
- Centralize address assignment
- Make sure managment ports get first MAC address in pool
- Properly propagate fail if address allocation failed
Submitted by: Andrew Duane <aduane@juniper.net>
set all three of the kernel, supervisor, and user-mode 64-bit mode
flags. While FreeBSD does not currently use the supervisor ring (and
hence this is effectively a NOP on most systems), doing this avoids
triggering an exception on 64-bit MIPS CPUs that don't support 32-bit
compatibility mode, and therefore don't allow clearing the SX bit.
Reviewed by: gonzo
MFC after: 3 days
Sponsored by: DARPA, SRI International
