We do this for FDT systems but not for ACPI ones.
Check the presence of the _CCA attribute.
Sponsored by: Ampere Computing, LLC
Reviewed by: andrew
Differential Revision: https://reviews.freebsd.org/D20144
Use BUS_DMA_NOWAIT for loads at initialization time.
Report actual numeric error code if any problem occurs at the
initialization.
Reported and tested by: pho
Reviewed by: mav
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D18741
initialize the controller.
According to the datasheet, the old code checks if port 2 (P2E, 0x4) was
the only enabled port (except port 0, which was ignored by mask 0xfe),
and issue a write to the PCS register to disable all but port 0, right
before ahci_ctlr_reset.
Some other operating systems would issue a port enable to all ports, but
since the current code only does the special initialization for ICH8M,
it entirely and rely on BIOS to do the right thing (the alternative
would be https://reviews.freebsd.org/D18300?id=50922 , should we see
reports that we really need to do it).
Reviewed by: mav
MFC after: 3 months
Differential Revision: https://reviews.freebsd.org/D18300
As part of Chuck's work on fixing kernel crashes caused by disk I/O
errors, it is useful to be able to trigger various kinds of
errors. This patch allows causing an AHCI-attached disk to disappear,
by having the driver keep the PHY disabled when the driver would
otherwise enable the PHY. It also allows making the disk reappear by
having the driver go back to setting the PHY enable/disable state as
it normal would and simulating the hardware event that causes a bus
rescan.
Submitted by: Chuck Silvers
Sponsored by: Netflix, Inc
Differential Revision: https://reviews.freebsd.org/D16043
Remove unused and easy to misuse PNP macro parameter
Inspired by r338025, just remove the element size parameter to the
MODULE_PNP_INFO macro entirely. The 'table' parameter is now required to
have correct pointer (or array) type. Since all invocations of the macro
already had this property and the emitted PNP data continues to include the
element size, there is no functional change.
Mostly done with the coccinelle 'spatch' tool:
$ cat modpnpsize0.cocci
@normaltables@
identifier b,c;
expression a,d,e;
declarer MODULE_PNP_INFO;
@@
MODULE_PNP_INFO(a,b,c,d,
-sizeof(d[0]),
e);
@singletons@
identifier b,c,d;
expression a;
declarer MODULE_PNP_INFO;
@@
MODULE_PNP_INFO(a,b,c,&d,
-sizeof(d),
1);
$ rg -l MODULE_PNP_INFO -- sys | \
xargs spatch --in-place --sp-file modpnpsize0.cocci
(Note that coccinelle invokes diff(1) via a PATH search and expects diff to
tolerate the -B flag, which BSD diff does not. So I had to link gdiff into
PATH as diff to use spatch.)
Tinderbox'd (-DMAKE_JUST_KERNELS).
Approved by: re (glen)
I was not aware Warner was making or planning to make forward progress in
this area and have since been informed of that.
It's easy to apply/reapply when churn dies down.
Inspired by r338025, just remove the element size parameter to the
MODULE_PNP_INFO macro entirely. The 'table' parameter is now required to
have correct pointer (or array) type. Since all invocations of the macro
already had this property and the emitted PNP data continues to include the
element size, there is no functional change.
Mostly done with the coccinelle 'spatch' tool:
$ cat modpnpsize0.cocci
@normaltables@
identifier b,c;
expression a,d,e;
declarer MODULE_PNP_INFO;
@@
MODULE_PNP_INFO(a,b,c,d,
-sizeof(d[0]),
e);
@singletons@
identifier b,c,d;
expression a;
declarer MODULE_PNP_INFO;
@@
MODULE_PNP_INFO(a,b,c,&d,
-sizeof(d),
1);
$ rg -l MODULE_PNP_INFO -- sys | \
xargs spatch --in-place --sp-file modpnpsize0.cocci
(Note that coccinelle invokes diff(1) via a PATH search and expects diff to
tolerate the -B flag, which BSD diff does not. So I had to link gdiff into
PATH as diff to use spatch.)
Tinderbox'd (-DMAKE_JUST_KERNELS).
There were some bits that were being set in cmd_flags (a field of AHCI's
command list structure) after cmd_flags was converted to little endian.
On a big endian host, such as PowerPC, this would set the wrong bits.
This was preventing AHCI driver from working on these hosts.
Reviewed by: jhibbits
Approved by: jhibbits (mentor)
Mark the PNP table, but still need to handle the CLASS / SUBCLASS /
REVID matching.
Reviewed by: imp, chuck
Submitted by: Lakhan Shiva Kamireddy <lakhanshiva@gmail.com>
Sponsored by: Google, Inc. (GSoC 2018)
Two modules with the same name cannot be loaded, so Marvell specific drivers
cannot have the same name as the generic drivers.
Files with the same name, even in different folders overlaps their .o files,
so in order to prepare for supporting Marvell platforms in GENERIC armv7
config, modify conflicting names.
Submitted by: Rafal Kozik <rk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D14743
Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
attachment code for various SOCs and busses. Remove all the static and
should-have-been-static and named-differently instances of it.
This should eliminate the recently-grown build warnings about multiple
definitions when building arm kernels.
busdma know, so that on architectures where dma isn't always coherent, we
know we don't have to write-back/invalidates cachelines on DMA operations.
Reviewed by: andrew, mav
Taking closer look on my ASM1062 I found that it has bunch of issues around
error recovery: reported wrong CCS, failed commands reported as completed,
READ LOG EXT times out after NCQ error. This patch workarounds first two
problems, that were making ATAPI devices close to unusable on these HBAs.
MFC after: 2 weeks
This file provides support for AHCI mode on Armada38x
and adds new optional AHCI device to arm/mv/files.mv.
Submitted by: Konrad Adamczyk <ka@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Reviewed by: zbb
Differential revision: https://reviews.freebsd.org/D9222
It occurred that some Marvell integrated controllers
require additional time after soft reset to work properly.
Introduce new quirk (AHCI_Q_MRVL_SR_DEL), that enable
such operation.
Submitted by: Konrad Adamczyk <ka@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Reviewed by: mav
Differential revision: https://reviews.freebsd.org/D9221
in some arm64 hardware, for example the AMD Opteron A1100.
Reviewed by: mav
Obtained from: ABT Systems Ltd
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D8852
The sim_vid, hba_vid, and dev_name fields of struct ccb_pathinq are
fixed-length strings. AFAICT the only place they're read is in
sbin/camcontrol/camcontrol.c, which assumes they'll be null-terminated.
However, the kernel doesn't null-terminate them. A bunch of copy-pasted code
uses strncpy to write them, and doesn't guarantee null-termination. For at
least 4 drivers (mpr, mps, ciss, and hyperv), the hba_vid field actually
overflows. You can see the result by doing "camcontrol negotiate da0 -v".
This change null-terminates those fields everywhere they're set in the
kernel. It also shortens a few strings to ensure they'll fit within the
16-character field.
PR: 215474
Reported by: Coverity
CID: 1009997 1010000 1010001 1010002 1010003 1010004 1010005
CID: 1331519 1010006 1215097 1010007 1288967 1010008 1306000
CID: 1211924 1010009 1010010 1010011 1010012 1010013 1010014
CID: 1147190 1010017 1010016 1010018 1216435 1010020 1010021
CID: 1010022 1009666 1018185 1010023 1010025 1010026 1010027
CID: 1010028 1010029 1010030 1010031 1010033 1018186 1018187
CID: 1010035 1010036 1010042 1010041 1010040 1010039
Reviewed by: imp, sephe, slm
MFC after: 4 weeks
Sponsored by: Spectra Logic Corp
Differential Revision: https://reviews.freebsd.org/D9037
Differential Revision: https://reviews.freebsd.org/D9038
ASMedia ASM1062 AHCI chips with some fancy firmware handling PMP inside
seems sometimes forgeting to set bits in PxIS, causing command timeouts.
Removal of this check fixes the issue by the theoretical cost of slightly
higher CPU usage in some odd cases, but this is what Linux does too.
MFC after: 1 month
Due to reading initialized variable, FIS receive area was always allocated
as 256 bytes, suitable for command-based switching, instead of 4096 bytes,
required for FIS-based switching. This caused memory corruption in case of
port multipliers used on FBS-capable HBAs (Marvell).
MFC after: 1 week
This is probably a NOP change since IS register is not activery used for
interrupts below the shared, but it looked odd to clear interrupts we did
not handle.
Incorrect sign expansion in variables that supposed to be a bit fields
caused infinite loop. Fixing this allows system properly detect maximal
possible 32 devices configured on AHCI HBA of BHyVe. That case did not
happen in a wild before due to lack of hardware AHCI HBAs with 32 ports.
Approved by: re (gjb@)
MFC after: 1 week
This change includes support for SCSI SMR drives (which conform to the
Zoned Block Commands or ZBC spec) and ATA SMR drives (which conform to
the Zoned ATA Command Set or ZAC spec) behind SAS expanders.
This includes full management support through the GEOM BIO interface, and
through a new userland utility, zonectl(8), and through camcontrol(8).
This is now ready for filesystems to use to detect and manage zoned drives.
(There is no work in progress that I know of to use this for ZFS or UFS, if
anyone is interested, let me know and I may have some suggestions.)
Also, improve ATA command passthrough and dispatch support, both via ATA
and ATA passthrough over SCSI.
Also, add support to camcontrol(8) for the ATA Extended Power Conditions
feature set. You can now manage ATA device power states, and set various
idle time thresholds for a drive to enter lower power states.
Note that this change cannot be MFCed in full, because it depends on
changes to the struct bio API that break compatilibity. In order to
avoid breaking the stable API, only changes that don't touch or depend on
the struct bio changes can be merged. For example, the camcontrol(8)
changes don't depend on the new bio API, but zonectl(8) and the probe
changes to the da(4) and ada(4) drivers do depend on it.
Also note that the SMR changes have not yet been tested with an actual
SCSI ZBC device, or a SCSI to ATA translation layer (SAT) that supports
ZBC to ZAC translation. I have not yet gotten a suitable drive or SAT
layer, so any testing help would be appreciated. These changes have been
tested with Seagate Host Aware SATA drives attached to both SAS and SATA
controllers. Also, I do not have any SATA Host Managed devices, and I
suspect that it may take additional (hopefully minor) changes to support
them.
Thanks to Seagate for supplying the test hardware and answering questions.
sbin/camcontrol/Makefile:
Add epc.c and zone.c.
sbin/camcontrol/camcontrol.8:
Document the zone and epc subcommands.
sbin/camcontrol/camcontrol.c:
Add the zone and epc subcommands.
Add auxiliary register support to build_ata_cmd(). Make sure to
set the CAM_ATAIO_NEEDRESULT, CAM_ATAIO_DMA, and CAM_ATAIO_FPDMA
flags as appropriate for ATA commands.
Add a new get_ata_status() function to parse ATA result from SCSI
sense descriptors (for ATA passthrough over SCSI) and ATA I/O
requests.
sbin/camcontrol/camcontrol.h:
Update the build_ata_cmd() prototype
Add get_ata_status(), zone(), and epc().
sbin/camcontrol/epc.c:
Support for ATA Extended Power Conditions features. This includes
support for all features documented in the ACS-4 Revision 12
specification from t13.org (dated February 18, 2016).
The EPC feature set allows putting a drive into a power power mode
immediately, or setting timeouts so that the drive will
automatically enter progressively lower power states after various
idle times.
sbin/camcontrol/fwdownload.c:
Update the firmware download code for the new build_ata_cmd()
arguments.
sbin/camcontrol/zone.c:
Implement support for Shingled Magnetic Recording (SMR) drives
via SCSI Zoned Block Commands (ZBC) and ATA Zoned Device ATA
Command Set (ZAC).
These specs were developed in concert, and are functionally
identical. The primary differences are due to SCSI and ATA
differences. (SCSI is big endian, ATA is little endian, for
example.)
This includes support for all commands defined in the ZBC and
ZAC specs.
sys/cam/ata/ata_all.c:
Decode a number of additional ATA command names in ata_op_string().
Add a new CCB building function, ata_read_log().
Add ata_zac_mgmt_in() and ata_zac_mgmt_out() CCB building
functions. These support both DMA and NCQ encapsulation.
sys/cam/ata/ata_all.h:
Add prototypes for ata_read_log(), ata_zac_mgmt_out(), and
ata_zac_mgmt_in().
sys/cam/ata/ata_da.c:
Revamp the ada(4) driver to support zoned devices.
Add four new probe states to gather information needed for zone
support.
Add a new adasetflags() function to avoid duplication of large
blocks of flag setting between the async handler and register
functions.
Add new sysctl variables that describe zone support and paramters.
Add support for the new BIO_ZONE bio, and all of its subcommands:
DISK_ZONE_OPEN, DISK_ZONE_CLOSE, DISK_ZONE_FINISH, DISK_ZONE_RWP,
DISK_ZONE_REPORT_ZONES, and DISK_ZONE_GET_PARAMS.
sys/cam/scsi/scsi_all.c:
Add command descriptions for the ZBC IN/OUT commands.
Add descriptions for ZBC Host Managed devices.
Add a new function, scsi_ata_pass() to do ATA passthrough over
SCSI. This will eventually replace scsi_ata_pass_16() -- it
can create the 12, 16, and 32-byte variants of the ATA
PASS-THROUGH command, and supports setting all of the
registers defined as of SAT-4, Revision 5 (March 11, 2016).
Change scsi_ata_identify() to use scsi_ata_pass() instead of
scsi_ata_pass_16().
Add a new scsi_ata_read_log() function to facilitate reading
ATA logs via SCSI.
sys/cam/scsi/scsi_all.h:
Add the new ATA PASS-THROUGH(32) command CDB. Add extended and
variable CDB opcodes.
Add Zoned Block Device Characteristics VPD page.
Add ATA Return SCSI sense descriptor.
Add prototypes for scsi_ata_read_log() and scsi_ata_pass().
sys/cam/scsi/scsi_da.c:
Revamp the da(4) driver to support zoned devices.
Add five new probe states, four of which are needed for ATA
devices.
Add five new sysctl variables that describe zone support and
parameters.
The da(4) driver supports SCSI ZBC devices, as well as ATA ZAC
devices when they are attached via a SCSI to ATA Translation (SAT)
layer. Since ZBC -> ZAC translation is a new feature in the T10
SAT-4 spec, most SATA drives will be supported via ATA commands
sent via the SCSI ATA PASS-THROUGH command. The da(4) driver will
prefer the ZBC interface, if it is available, for performance
reasons, but will use the ATA PASS-THROUGH interface to the ZAC
command set if the SAT layer doesn't support translation yet.
As I mentioned above, ZBC command support is untested.
Add support for the new BIO_ZONE bio, and all of its subcommands:
DISK_ZONE_OPEN, DISK_ZONE_CLOSE, DISK_ZONE_FINISH, DISK_ZONE_RWP,
DISK_ZONE_REPORT_ZONES, and DISK_ZONE_GET_PARAMS.
Add scsi_zbc_in() and scsi_zbc_out() CCB building functions.
Add scsi_ata_zac_mgmt_out() and scsi_ata_zac_mgmt_in() CCB/CDB
building functions. Note that these have return values, unlike
almost all other CCB building functions in CAM. The reason is
that they can fail, depending upon the particular combination
of input parameters. The primary failure case is if the user
wants NCQ, but fails to specify additional CDB storage. NCQ
requires using the 32-byte version of the SCSI ATA PASS-THROUGH
command, and the current CAM CDB size is 16 bytes.
sys/cam/scsi/scsi_da.h:
Add ZBC IN and ZBC OUT CDBs and opcodes.
Add SCSI Report Zones data structures.
Add scsi_zbc_in(), scsi_zbc_out(), scsi_ata_zac_mgmt_out(), and
scsi_ata_zac_mgmt_in() prototypes.
sys/dev/ahci/ahci.c:
Fix SEND / RECEIVE FPDMA QUEUED in the ahci(4) driver.
ahci_setup_fis() previously set the top bits of the sector count
register in the FIS to 0 for FPDMA commands. This is okay for
read and write, because the PRIO field is in the only thing in
those bits, and we don't implement that further up the stack.
But, for SEND and RECEIVE FPDMA QUEUED, the subcommand is in that
byte, so it needs to be transmitted to the drive.
In ahci_setup_fis(), always set the the top 8 bits of the
sector count register. We need it in both the standard
and NCQ / FPDMA cases.
sys/geom/eli/g_eli.c:
Pass BIO_ZONE commands through the GELI class.
sys/geom/geom.h:
Add g_io_zonecmd() prototype.
sys/geom/geom_dev.c:
Add new DIOCZONECMD ioctl, which allows sending zone commands to
disks.
sys/geom/geom_disk.c:
Add support for BIO_ZONE commands.
sys/geom/geom_disk.h:
Add a new flag, DISKFLAG_CANZONE, that indicates that a given
GEOM disk client can handle BIO_ZONE commands.
sys/geom/geom_io.c:
Add a new function, g_io_zonecmd(), that handles execution of
BIO_ZONE commands.
Add permissions check for BIO_ZONE commands.
Add command decoding for BIO_ZONE commands.
sys/geom/geom_subr.c:
Add DDB command decoding for BIO_ZONE commands.
sys/kern/subr_devstat.c:
Record statistics for REPORT ZONES commands. Note that the
number of bytes transferred for REPORT ZONES won't quite match
what is received from the harware. This is because we're
necessarily counting bytes coming from the da(4) / ada(4) drivers,
which are using the disk_zone.h interface to communicate up
the stack. The structure sizes it uses are slightly different
than the SCSI and ATA structure sizes.
sys/sys/ata.h:
Add many bit and structure definitions for ZAC, NCQ, and EPC
command support.
sys/sys/bio.h:
Convert the bio_cmd field to a straight enumeration. This will
yield more space for additional commands in the future. After
change r297955 and other related changes, this is now possible.
Converting to an enumeration will also prevent use as a bitmask
in the future.
sys/sys/disk.h:
Define the DIOCZONECMD ioctl.
sys/sys/disk_zone.h:
Add a new API for managing zoned disks. This is very close to
the SCSI ZBC and ATA ZAC standards, but uses integers in native
byte order instead of big endian (SCSI) or little endian (ATA)
byte arrays.
This is intended to offer to the complete feature set of the ZBC
and ZAC disk management without requiring the application developer
to include SCSI or ATA headers. We also use one set of headers
for ioctl consumers and kernel bio-level consumers.
sys/sys/param.h:
Bump __FreeBSD_version for sys/bio.h command changes, and inclusion
of SMR support.
usr.sbin/Makefile:
Add the zonectl utility.
usr.sbin/diskinfo/diskinfo.c
Add disk zoning capability to the 'diskinfo -v' output.
usr.sbin/zonectl/Makefile:
Add zonectl makefile.
usr.sbin/zonectl/zonectl.8
zonectl(8) man page.
usr.sbin/zonectl/zonectl.c
The zonectl(8) utility. This allows managing SCSI or ATA zoned
disks via the disk_zone.h API. You can report zones, reset write
pointers, get parameters, etc.
Sponsored by: Spectra Logic
Differential Revision: https://reviews.freebsd.org/D6147
Reviewed by: wblock (documentation)
can handle it, and add the code to add it to the FIS that's sent to
the drive. The mvs driver is the only other ATA driver in the system,
and its hardware doesn't appear to support setting the Auxiliary
register.
Differential Revision: https://reviews.freebsd.org/D5598
as before. The common scheduling bits have moved from inline code in
each of the CAM periph drivers into a library that implements the
default scheduling.
In addition, a number of rate-limiting and I/O preference options can
be enabled by adding CAM_IOSCHED_NETFLIX to your config file. A number
of extra stats are also maintained. CAM_IOSCHED_NETFLIX isn't on by
default because it uses a separate BIO_READ and BIO_WRITE queue, so
doesn't honor BIO_ORDERED between these two types of operations. We
already didn't honor it for BIO_DELETE, and we don't depend on
BIO_ORDERED between reads and writes anywhere in the system (it is
currently used with BIO_FLUSH in ZFS to make sure some writes are
complete before others start and as a poor-man's soft dependency in
one place in UFS where we won't be issuing READs until after the
operation completes). However, out of an abundance of caution, it
isn't enabled by default.
Plus, this also brings in NCQ TRIM support for those SSDs that support
it. A black list is also provided for known rogues that use NCQ trim
as an excuse to corrupt the drive. It was difficult to separate out
into a separate commit.
This code has run in production at Netflix for over a year now.
Sponsored by: Netflix, Inc
Differential Revision: https://reviews.freebsd.org/D4609
Changes introduced to AHCI code adding support for MSI-x
caused interrupt storm on Alpine boards.
This is unintended behaviour so added quirk to omit this functionality.
Reviewed by: mav
Submitted by: Marcin Mazurek <mma@semihalf.com>
Obtained from: Semihalf
Sponsored by: Annapurna Labs
Differential Revision: https://reviews.freebsd.org/D4301
ahci.c had one signed long, which was passed into rman, rather than u_long.
After the switch of rman_res_t from size u_long to size uintmax_t, the sign
extension caused ranges to get messed up, and ahcich* to not attach.
There may be more signed longs used in this way, which will be fixed as they're
reported.
Reported by: pho
Summary:
Migrate to using the semi-opaque type rman_res_t to specify rman resources. For
now, this is still compatible with u_long.
This is step one in migrating rman to use uintmax_t for resources instead of
u_long.
Going forward, this could feasibly be used to specify architecture-specific
definitions of resource ranges, rather than baking a specific integer type into
the API.
This change has been broken out to facilitate MFC'ing drivers back to 10 without
breaking ABI.
Reviewed By: jhb
Sponsored by: Alex Perez/Inertial Computing
Differential Revision: https://reviews.freebsd.org/D5075
typically memory mapped bus, for example on the AMD Opteron A1100 the AHCI
device is mapped in the CPUs address space, and not through a PCI
controller.
Further work is needed for this to work with ACPI as this is expected to be
common on ARMv8 servers.
Reviewed by: mav, mmel
Obtained from: mmel, ABT Systems Ltd
Relnotes: yes
Sponsored by: SoftIron Inc
Differential Revision: https://reviews.freebsd.org/D4269