most kernels before FreeBSD 9.0. Remove such modules and respective kernel
options: atadisk, ataraid, atapicd, atapifd, atapist, atapicam. Remove the
atacontrol utility and some man pages. Remove useless now options ATA_CAM.
No objections: current@, stable@
MFC after: never
implementation specific vs. the common architecture definition.
Bring PPC4XX defines (PSL, SPR, TLB). Note the new definitions under
BOOKE_PPC4XX are not used in the code yet.
This change set is not supposed to affect existing E500 support, it's just
another reorg step before bringing support for E500mc, E5500 and PPC465.
Obtained from: AppliedMicro, Freescale, Semihalf
As of FreeBSD 8, this driver should not be used. Applications that use
posix_openpt(2) and openpty(3) use the pts(4) that is built into the
kernel unconditionally. If it turns out high profile depend on the
pty(4) module anyway, I'd rather get those fixed. So please report any
issues to me.
The pty(4) module is still available as a kernel module of course, so a
simple `kldload pty' can be used to run old-style pseudo-terminals.
stack. It means that all legacy ATA drivers are disabled and replaced by
respective CAM drivers. If you are using ATA device names in /etc/fstab or
other places, make sure to update them respectively (adX -> adaY,
acdX -> cdY, afdX -> daY, astX -> saY, where 'Y's are the sequential
numbers for each type in order of detection, unless configured otherwise
with tunables, see cam(4)).
ataraid(4) functionality is now supported by the RAID GEOM class.
To use it you can load geom_raid kernel module and use graid(8) tool
for management. Instead of /dev/arX device names, use /dev/raid/rX.
Kernel sources for 64-bit PowerPC, along with build-system changes to keep
32-bit kernels compiling (build system changes for 64-bit kernels are
coming later). Existing 32-bit PowerPC kernel configurations must be
updated after this change to specify their architecture.
The following systems are affected:
- MPC8555CDS
- MPC8572DS
This overhaul covers the following major changes:
- All integrated peripherals drivers for Freescale MPC85XX SoC, which are
currently in the FreeBSD source tree are reworked and adjusted so they
derive config data out of the device tree blob (instead of hard coded /
tabelarized values).
- This includes: LBC, PCI / PCI-Express, I2C, DS1553, OpenPIC, TSEC, SEC,
QUICC, UART, CFI.
- Thanks to the common FDT infrastrucutre (fdtbus, simplebus) we retire
ocpbus(4) driver, which was based on hard-coded config data.
Note that world for these platforms has to be built WITH_FDT.
Reviewed by: imp
Sponsored by: The FreeBSD Foundation
the 'debugging' section of any HEAD kernel and enable for the mainstream
ones, excluding the embedded architectures.
It may, of course, enabled on a case-by-case basis.
Sponsored by: Sandvine Incorporated
Requested by: emaste
Discussed with: kib
in Freescale system-on-chip devices.
The following algorithms and schemes are currently supported:
- 3DES, AES, DES
- MD5, SHA1, SHA256, SHA384, SHA512
Reviewed by: philip
Obtained from: Freescale, Semihalf
controller in the VIA southbridge functional in the CDS
(Configurable Development System) for MPC85XX.
The embedded USB controllers look operational but the
interrupt steering is still wrong.
- interrupt coalescing
- polling
- jumbo frames
- multicast
- VLAN tagging
The enhanced version of the chip (eTSEC) can also take advantage of:
- TCP/IP checksum calculation h/w offloading
Obtained from: Freescale, Semihalf
The kernel config file is KERNCONF=MPC85XX, so the usual procedure applies:
1. make buildworld TARGET_ARCH=powerpc
2. make buildkernel TARGET_ARCH=powerpc TARGET_CPUTYPE=e500 KERNCONF=MPC85XX
This default config uses kernel-level FPU emulation. For the soft-float world
approach:
1. make buildworld TARGET_ARCH=powerpc TARGET_CPUTYPE=e500
2. disable FPU_EMU option in sys/powerpc/conf/MPC85XX
3. make buildkernel TARGET_ARCH=powerpc TARGET_CPUTYPE=e500 KERNCONF=MPC85XX
Approved by: cognet (mentor)
MFp4: e500
