chipsets, based on Linux's via-agp.c. On boot, the system selects which AGP
version to use based on the inserted card. If v2 was chosen, the chipset
needs to be programmed with the v2 registers still. Also included in kern/69953
are changes to make the programming of the v3 registers match linux, but that
will be left out until the need to do so is confirmed (want specs or a tester).
PR: kern/69953
Submitted by: Oleg Sharoiko <os@rsu.ru>
Tested by: Oleg Sharoiko <os@rsu.ru>, Geoff Speicher <geoff@speicher.org>
(full version from PR)
- Avoid an additional lock acquire/release when leaving xl_intr(), by
changing xl_start*() to xl_start*_locked(), and calling the appropriate
routine by chip revision (as the DMA descriptors are different).
- Simplify the appropriate routines now that they are called with the
lock held.
This should save a significant amount of CPU cycles spent on servicing
each interrupt for both UP and SMP whilst remaining MPSAFE.
Tested by: rwatson
- Add *_locked() entry points as needed to avoid unnecessary lock thrashing.
- Use these entry points wisely.
- Only acquire the lock once when servicing an interrupt.
- Check 'suspended' on interrupt to avoid racing detach.
- Correct a mis-spelled comment.
- Don't take the lock in vr_reset() to avoid lock thrashing in attach.
- Comment this.
Reviewed by: -net (silence)
- Avoid unnecessary re-acquisition elsewhere by adding *_locked()
entry points as needed.
- Correct locking for the DEVICE_POLLING case.
- Hold the driver lock for the entire duration of interrupt servicing,
to avoid unneeded, expensive re-acquisition; use *_locked() entry
points as needed.
Reviewed by: -net (silence)
- Eliminate the use of a recursive mutex.
- Mark the driver INTR_MPSAFE.
This work is incomplete and will be refined in a future commit.
- Most notably, _locked() variants of entry points need to be introduced.
- The mii upcall/downcall may still be racy.
- Add a stubbed-out guard against racing rl_detach() for the time being.
Tested on: UP, debug.mpsafenet && !debug.mpsafenet
Reviewed by: silence on -net
Use C99 types. Use ANSI function definitions. Sort prototypes.
Split long lines correctly. Punctuate/wordsmith comments.
Use device_printf()/if_printf() where possible.
Reviewed by: -net (silence)
- Eliminate the use of a recursive mutex.
- Mark the driver as INTR_MPSAFE.
- Split the default media choice code out into xl_choose_media() to
avoid making poor assumptions about the state of the lock during attach.
- The miibus upcall/downcall paths may still be racy.
Change to commented-out locking assertions there for now.
- Tested with nfsclient, routed, ssh, ntp, dhclient and quagga bgpd.
- This needs SMP test coverage. I do not have such resources.
Tested on: UP, !debug.mpsafenet && debug.mpsafenet
Hardware: 3C905B-TX (0x905510b7)
- Use device_printf() during device probe/attach.
- Move if_xname initialization to before xl_reset() is called.
- Use if_printf() at all other times after struct ifnet has been
initialized.
- Remove recursive locking situations. Remove the MTX_RECURSE bit.
- Take the lock for any routine which is not called from within if_vr.c
itself; this includes entry points called by newbus, ifnet, callout,
ifmedia, and polling subsystems.
- Remove spl references from the code added to miibus callbacks in rev 1.60.
- Add the INTR_MPSAFE bit.
- Tidy up some assignments; locks are not needed for taking the address
of something at a known offset, for example.
- Tested on the machine this was committed from.
Tested on: UP only, !debug.mpsafenet && debug.mpsafenet
Reviewed by: rwatson
Put some braces around the busy-wait loop in vr_rxeoc() to make the
no-op semicolon more obvious.
No functional changes.
Running on the machine I am committing from without problems.
Reviewed by: jmallett
following drivers: bfe(4), em(4), fxp(4), lnc(4), tun(4), de(4) rl(4),
sis(4) and xl(4)
More patches are pending on: http://peoples.freebsd.org/~mlaier/ Please take
a look and tell me if "your" driver is missing, so I can fix this.
Tested-by: many
No-objection: -current, -net
