the ataahci(4) and atamarvell(4) drivers share it between the host and
the controller.
- Spell some zeros as BUS_DMA_WAITOK when used as bus_dmamem_alloc() flags.
MFC after: 2 weeks
coherent.
- Add some missing bus_dmamap_sync() calls. This includes putting such
calls before calling reply handlers instead of calling bus_dmamap_sync()
for the request queue from individual reply handlers as these handlers
generally read back updates by the controller.
Tested on amd64 and sparc64.
MFC after: 2 weeks
It defaults to -5 dBm for eeproms earlier than v21.
This apparently only applies to Merlin (AR9280) or later,
earlier 11n chipsets have a power table offset of 0.
All the code in ath9k which checks the power table offset
and takes it into account first ensures the chip is
Merlin or later.
The earlier way of doing debugging would evaluate the function parameters
before calling the HALDEBUG. In the case of detailed register debugging
would mean a -lot- of unneeded register IO and other stuff was going on.
This method evaluates the ath_hal_debug variable before the function
parameters are evaluated, drastically reducing the amount of overhead
enabling HAL debugging during compilation.
- everything related to LRO should be in #ifdef INET blocks
- reorder sge_iq's fields so that the most frequently used are all together
- pull all rx code into t4_intr_data directly
- let go of the ingress queue lock when passing up data
- refill the freelist only if it is short of at least 32 buffers
determining whether to use MRR or not.
It uses the 11g protection mode when calculating 11n related stuff, rather
than checking the 11n protection mode.
Furthermore, the 11n chipsets can quite happily handle multi-rate retry w/
protection; the TX path and rate control modules need to be taught about
that.
* change the BB gating logic to explicitly define which chips are covered;
the ath9k method isn't as clear.
* don't disable the BB gating for now, the ar5416 initvals have it, and the
ar9160 initval sets it to 0x0. Figure out why before re-enabling this.
* migrate the Merlin (ar9280) applicable WAR from the Kite (ar9285) code
(which won't get called for Merlin!) and stuff it in here.
* add dot11rate_label() which returns Mb or MCS based on legacy or HT
* use it everywhere dot11rate() is used
* in the "current selection" part at the top of the debugging output,
otuput what the rate itself is rather than the rix. The rate index
(rix) has very little meaning to normal humans who don't know how
to find the PHY settings for each of the chipsets; pointing out the
rix rate and type is likely more useful.
These flags are just plain wrong - they're the node flags from negotiation,
not the configured flags. I'll jump in later on and figure out exactly
what should be done to properly set these two flags when in both STA mode
(ie, what the AP says is possible and what's configured) and AP mode
(ie, where the AP has a configuration, but then negotiates what's possible
with each node, so per-node configuration can and will differ.)
This allows the 11n 2.4ghz/ht20 mode to associate (but perform poorly still)
and exchange MCS rates with atheros reference APs and a Cisco/Linksys
E3000 AP.
operation. Previously ownership was transferred to hardware before
setting address of new RX buffer such that it was possible for
hardware to use wrong RX buffer address.
While here keep compiler from re-ordering instructions by declaring
descriptor members volatile. Memory barriers would do the same job
but volatile is supposed to be cheaper than using memory barriers,
especially on MP systems.
Submitted by: marius
MFC after: 1 week
mps.c: Hide the 'out of chain frames' warning behind MPS_INFO.
mps_sas.c: Hide the SIM queue freeze/unfreeze messages behind MPS_INFO.
mpsvar.h: Bump the number of chain frames from 1024 to 2048. From
testing, it looks like this makes it less likely that we'll
run out of chain frames, and it doesn't cost much memory
(32K).
MFC after: 3 days
means of allowing vendor specific interface class for audio and MIDI devices.
- Add new quirks for this. The vendor and product list in OpenBSD's
dev/usb/umidi_quirks.c was used as reference.
MFC after: 14 days
Approved by: thompsa (mentor)
causing the size calculation to be truncated to the size of an int
(32-bits on all current architectures).
Submitted by: Anish akgupt3 of gmail
MFC after: 1 week
link flips during alias address insertion or dhclient operation.
While I'm here remove dc_reset() in DC_ISR_BUS_ERR case. Device is
fully reinitialized again in dc_init_locked().
* Turn ath_tx_calc_ctsduration() into a function that
returns the ctsduration, or -1 for HT rates;
* add a printf() to ath_tx_calc_ctsduration() which will be
very loud if somehow that function is called with an MCS
rate;
* Add ath_tx_get_rtscts_rate() which returns the RTS/CTS
rate to use for the given data rate, incl. the short
preamble flag;
* Only call ath_tx_calc_ctsduration() for non-11n chipsets;
11n chipsets don't require the rtscts duration to be
calculated.
It's used to calculate:
* the initial per-rate entries for short/long preamble ACK durations;
* packet durations for TDMA slot decisions;
* RTS/CTS protection durations;
* updating the duration field in the 802.11 frame header
This way invalid durations will generate a warning, prompting for it to be
fixed.
