in attach.
- Change a EISA_CHANNEL_CLEAR to EISA_CHANNEL_BUSY in ida_v1_submit().
This may fix the problem with EISA IDA adapters though we have not heard
back from testers yet.
Reviewed by: jlemon
o Eliminate cross calls between the devices. Instead move to using the
newbus messaging system. Added three new card calls: attach_card,
detach_card, get_type.
o Eliminate interrupt routine in pccard we never use.
o Move from deactivate to detach for removing cards.
o Start mapping CIS memory, but it is broken and causes panics. At least
it is closer to working than before.
o Eliminate struct device everywhere. It was bogus.
o Initialize softc for pccard device so we have valid pointers to
ourselves.
o Implement routine to find the pcic ivar for a child device of the pccard so
we can use it to talk to the pcic hardware.
o Lots of minor tiding up.
This version now panics when we try to read the CIS. The next batch
of work to make this work is what was outlined in my posting to mobile
about resource allocation and such.
- implement user-initiated background drive rebuild
- implement user-initiated background consistency check
- log controller-initiated background rebuild/check operations
Try to fix the elusive "invalid log operation" bug, and panic if we do
hit this one in the hopes of getting better information.
Tidy up diagnostic messages.
Try to use disk_create/disk_destroy correctly. This isn't working
properly yet, but it's not clear whose fault that is.
robust enough to work with dhcp. Essentially the driver returns to userland
before certain commands have been completed by the card. I'm trying to
work out the best way to fix this. There are very minor functional changes,
most of this is debugging.
Rework of debugging so a bit mask is used and re-allocation around the place.
Tried to protect ray_init with a tsleep until the network has been joined. I think this is only a partial fix as we also update the mcast and promisc
values.
Update the license in the rio_usb.h (now rio500_usb.h) to not be GPL.
Sorry for committing that file in the first place. The change of license
was agreed to by the original author.
non-device code.
* Re-implement the method dispatch to improve efficiency. The new system
takes about 40ns for a method dispatch on a 300Mhz PII which is only
10ns slower than a direct function call on the same hardware.
This changes the new-bus ABI slightly so make sure you re-compile any
driver modules which you use.
- Add support for ISA based DPT adapters (this doesn't quite work yet).
- Sync dpt_eisa.c with my local copy.
- Simplify how EISA IDs are matched.
- Prototype.
- Formatting nits.
- Conform to how I do things in dpt_pci.c/dpt_isa.c.
- Modify dpt_scsi.c:dpt_alloc() to DTRT with newbus.
- Add some comments to dpt_scsi.c:dpt_pio_get_conf().
- Add additional check to dpt_scsi.c:dpt_get_conf().
- Add some useful error messages to dpt_scsi.c:dpt_init().
request could be deallocated before the top half had finished
issuing it. The problem seems only to happen with IDE drives
and vn devices, but theoretically it could happen with any
drive. This is the most important part of a possible series
of fixes designed to remove race conditions without locking
out interrupts for longer than absolutely necessary.
Reported-by: sos
Fix-supplied-by: dillon
From the README:
Any IEEE 802.11 cards use AMD Am79C930 and Harris (Intersil) Chipset
with PCnetMobile firmware by AMD.
BayStack 650 1Mbps Frequency Hopping PCCARD adapter
BayStack 660 2Mbps Direct Sequence PCCARD adapter
Icom SL-200 2Mbps Direct Sequence PCCARD adapter
Melco WLI-PCM 2Mbps Direct Sequence PCCARD adapter
NEL SSMagic 2Mbps Direct Sequence PCCARD adapter
Netwave AirSurfer Plus
1Mbps Frequency Hopping PCCARD adapter
Netwave AirSurfer Pro
2Mbps Direct Sequence PCCARD adapter
Known Problems:
WEP is not supported.
Does not create IBSS itself.
Cannot configure the following on FreeBSD:
selection of infrastructure/adhoc mode
ESSID
...
Submitted by: Atsushi Onoe <onoe@sm.sony.co.jp>
connected during boot and the vpo module is in the kernel/loaded.
In the case where the module is loaded at some later stage with kldload,
the CAM bus is now rescanned as well.
- The driver now uses bus_space() and runs on NetBSD 1.4.2
Submitted by Thomas Klausner <wiz@danbala.ifoer.tuwien.ac.at>
- Remove startup quirks for video and vbi capture for PAL users.
PAL TV users can now run FXTV and Alevt in any order.
- Add support for cable channels >100
Submitted by Scott Presnell <srp@zgi.com>
- New MSP3410/3415 setup code added. This is experimental.
Please set the sysctl hw.bt848.slow_msp_audio to 1 for this.
Submitted by Frank Nobis<fn@radio-do.de>
Pass sc->dev rather than a bogusly cast pccard_softc *sc.
This allows us to insert and remove cards w/o panicing the kernel.
However, the cis isn't mapped in, so the pccard_scan_cis function
fails.
- Request the maximum number of LUNs on a device if it is
a Bulk-Only device.
- Handle NO_TEST_UNIT_READY case for SCSI
- Add NO_START_STOP quirk for LS-120
- Fix a KASSERT which was the wrong way around.
- Kickstart the LS-120 with the infamous LS-120 specific command of
which no one knows what it doesn, apart from the fact that it appeared
in the Linux code someday.
kernel. Justin agress that there is no other reasonable alternative to
do automatic rescans on connect.
The problem is that when a new device attaches to a SIM (SCSI host
controller) we need to send a XPT_SCAN_BUS command to the SIM using
xpt_action. This requires however that there is a peripheral available
to take the command (otherwise xpt_done and later bomb). The RESCAN
ioctl uses the same periph.
This enables a USB mass storage drive to do an automatic rescan on
connection of the drive.
The automatic dropping of a CAM entry on disconnection was already
working (asynchronous event).
The next thing to do is find someone to commit a change to vpo to do the
same thing. Just port umass_cam_rescan and friends across to that
driver.
Approved by: gibbs
unit numbers all wrong. This did not show up because most of them where
zero anyway.
Use a separate buffer for command transforms instead of fiddling with
the existing cdb_bytes.
Take CAM_CDB_POINTER into account. Nobody is using it, but someone might
in the future.
Be more picky about what to accept in the UFI command set.
First attempt at implementing the ATAPI command protocol transforms.
This should at least make Imation Superdisk and other e-Shuttle based
devices show as attached. Maybe they even work to some extent.
(Much of this done by script)
Move B_ORDERED flag to b_ioflags and call it BIO_ORDERED.
Move b_pblkno and b_iodone_chain to struct bio while we transition, they
will be obsoleted once bio structs chain/stack.
Add bio_queue field for struct bio aware disksort.
Address a lot of stylistic issues brought up by bde.
