- OVERRIDE_TUNER: allows you to manually choose the tuner type for those
cards that fail to probe properly. See source for legal
values.
- OVERRIDE_DBX: allows you to manually choose DBX or NO DBX for those
cards that fail to probe properly.
0 == no DBX circuit present, 1 == DBX circuit present.
should work with no driver changes, though not all features are currently
used.
Remove code that was conditional on NEW_SCSICONF not being defined. This
was temporary code, that at a time got excluded correctly, until the new
scsiconf became the default, and NEW_SCSICONF was no longer specified.
Add support for quirks defined in scsiconf.c. For now only the HP3724/5
needs an entry, since that drive can't be used with tags.
device probe of a host to PCI bridge may modify that value, based on
its knowledge of device specific registers. This makes the Intel XXpress
work, as verified by: Terje Marthinussen <terjem@cc.uit.no>.
Return failure, if the enable bit corresponding to the map type has not
been set in the command register. This feature was requested by Justin
Gibbs, who pointed out that some early PCI to PCI bridges do not correctly
support memory windows (I assume because of the risk of deadlocks that
have been taken care of in the PCI 2.2 spec) and that some BIOS clears
the memory address decode enable bit in the command register of the PCI
device, if it finds them behind such a bridge.
1) Stop at the first map register that contains a zero value.
2) When testing for the map size work up from low values, since
this works around a bug in some BusLogic SCSI card, which has
the 16 upper port base address bits hardwired to zero.
The config register dump printed in the bootverbose case has
been slightly rearranged.
reality. There will be a new call interface, but for now the file
pci_compat.c (which is to be deleted, after all drivers are converted)
provides an emulation of the old PCI bus driver functions. The only
change that might be visible to drivers is, that the type pcici_t
(which had been meant to be just a handle, whose exact definition
should not be relied on), has been converted into a pcicfgregs* .
The Tekram AMD SCSI driver bogusly relied on the definition of pcici_t
and has been converted to just call the PCI drivers functions to access
configuration space register, instead of inventing its own ...
This code is by no means complete, but assumed to be fully operational,
and brings the official code base more in line with my development code.
A new generic device descriptor data type has to be agreed on. The PCI
code will then use that data type to provide new functionality:
1) userconfig support
2) "wired" PCI devices
3) conflicts checking against ISA/EISA
4) maps will depend on the command register enable bits
5) PCI to Anything bridges can be defined as devices,
and are probed like any "standard" PCI device.
The following features are currently missing, but will be added back,
soon:
1) unknown device probe message
2) suppression of "mirrored" devices caused by ancient, broken chip-sets
This code relies on generic shared interrupt support just commited to
kern_intr.c (plus the modifications of isa.c and isa_device.h).
Added [SR]RGBMASKs ioctl for byte swapping.
1.16 4/20/97 Randall Hopper <rhh@ct.picker.com>
Generalized RGBMASK ioctls for general pixel
format setting [SG]ACTPIXFMT, and added query API
to return driver-supported pix fmts GSUPPIXFMT.
1.17 4/21/97 hasty@rah.star-gate.com
Clipping support added.
1.18 4/23/97 Clean up after failed CAP_SINGLEs where bt
interrupt isn't delivered, and fixed fixing
CAP_SINGLEs that for ODD_ONLY fields.
Submitted by: individuals in above log messages.
There are various options documented in i386/conf/LINT, there is more to
come over the next few days.
The kernel should run pretty much "as before" without the options to
activate SMP mode.
There are a handful of known "loose ends" that need to be fixed, but
have been put off since the SMP kernel is in a moderately good condition
at the moment.
This commit is the result of the tinkering and testing over the last 14
months by many people. A special thanks to Steve Passe for implementing
the APIC code!
large enough to contain the ethernet header. There appears to be a
condition where the card can return "0" in some failure cases, and this
causes bad things to happen (a panic).
type mismatches. There was no problem in practice (at least on 386's).
Removed NetBSD-related TIMEOUT macro. NetBSD uses the same BSD4.4Lite
timeout interface as FreeBSD. As a concession to portability, declare
the timeout function without using the FreeBSD timeout_t typedef.
This patch fixes the problem of vic only capturing an even or odd frame plus
the my early patch for missing frames with resolutions higher than 320x240
in rgb mode.
The yuv422 patch introduces a minor bug in that a green line appears at the
bottom of the captured window . There is no easy work around for this right
now.
Reviewed by: various bt848 hackers
Submitted by: Amancio Hasty <hasty@rah.star-gate.com>
Randall Hopper <rhh@ct.picker.com> GHUE/GBRIGHT bug
Louis Mamakos made a new bt848 struct, including massive changes to the entire
body of code, substituting array offsets with struct members.
Randall Hopper aadded fixes of BT848_GHUE & BT848_GBRIG.
I (fsmp):
added polled hardware i2c routines,
removed all existing software i2c routines.
added eeprom support.
form `tv = time'. Use a new function gettime(). The current version
just forces atomicicity without fixing precision or efficiency bugs.
Simplified some related valid accesses by using the central function.
Michael submitted code to activate the audio muxes.
fsmp:
extended those changes for different boards.
auto-detection of board types.
auto-detection of tuner types.
auto-detection of stereo option.
Fixed a bug in fxp_mdi_write - a hex number was missing a preceding 0x
and this was causing the routine to not wait for a PHY write to complete.
Added support for link0, link1, and link2 flags to toggle auto-
negotiation, 10/100, and half/full duplex:
link0 disable auto-negotiation
When set, these flags then have meaning:
-link1 10Mbps
link1 100Mbps
-link2 half duplex
link2 full duplex
...needs a manual page.
I broke the cable tuning with my 'TEST_A' code. Remove TEST_A define
till I finish this change for both tuning modes. Note that this
will effectively break the new TVTUNER_SETFREQ/TVTUNER_GETFREQ ioctl()s.
These aren't used by anyone but me yet (attempt to provide full resolution
fine tuning for "fringe" stations) so it should be no problem
written:
1) Full duplex mode is now supported (and works!)
2) The 10Mbps-only PCI Pro/10 should now work (untested, however)
Thanks to Justin Gibbs for providing a PCI bus analyzer trace while the
Intel Windows driver was configuring the board...this made it possible
to figure out the mystery bit that I wasn't setting in the PHY for full
duplex to work.
