algorithm, supplied by wpaul himself. The lame one has an origin
that's been called into question, so rather than argue about that (one
could make an excellent fair use argument), replace it with better
code since that's what FreeBSD is about.
Submitted by: wpaul[1], Klaus Klein
[1] Bill called this a silly bikeshed. Maybe his is not incorrect.
they all do and handle that without alarming the user. Also pull in a bit
of defensive code from OpenBSD that triggers when a card is recognised but
not properly classified as either Genesis or Yukon. Not that I could ever
have needed this. :-)
Obtained from: OpenBSD/NetBSD (partially)
MFC after: 2 weeks
the packets are immediately returned for sending (e.g. when bridging
or packet forwarding). There are more efficient ways to do this
but for now use the least intrusive approach.
Reviewed by: imp, rwatson
multicast hash are written. There are still two distinct algorithms used,
and there actually isn't any reason each driver should have its own copy
of this function as they could all share one copy of it (if it grew an
additional argument).
if_xname, if_dname, and if_dunit. if_xname is the name of the interface
and if_dname/unit are the driver name and instance.
This change paves the way for interface renaming and enhanced pseudo
device creation and configuration symantics.
Approved By: re (in principle)
Reviewed By: njl, imp
Tested On: i386, amd64, sparc64
Obtained From: NetBSD (if_xname)
Tested at 100Mbit only, using Asus P4P800 onboard 3C940.
The -stable version of this patch I have in use for ~2 weeks now, and works
just fine for me.
Based on: Nathan L. Binkert's patch for OpenBSD
Patch submitted by and thanks to: Jung-uk Kim <jkim@niksun.com>
MFC after: 2 weeks
forced to do slightly bogus power state manipulation. However, this
is one of those features that is preventing further progress, so mark
them as BURN_BIRDGES like I did for the drivers in sys/dev/...
This, like the other change, are a no-op unless you have BURN_BRIDGES
in your kernel.
if attach succeeded. device_is_alive just tells us that probe
succeeded. Since we were using it to do things like detach net
interfaces, this caused problems when there were errors in the attach
routine.
Symptoms of problem reported by: martin blapp
- Unconditionally call *_stop() if device is in the tree. This is to
prevent callouts from happening after the device is gone. Checks for
bus_child_present() should be added in the future to keep from touching
potentially non-existent hardware in *_detach(). Found by iedowse@.
- Always check for and free miibus children, even if the device is not in
the tree since some failure cases could have gotten here.
- Call ether_ifdetach() in the irq setup failure case
- ti(4), xl(4): move ifmedia_init() calls to the beginning of attach so
that ifmedia_removeall() can be unconditionally called on detach. There
is no way to detect whether ifmedia has been initialized without using
a separate variable (as tl(4) does).
- Add comments to indicate assumptions of code path
network layer (ether).
- Don't abuse module names to facilitate ifconfig module loading;
such abuse isn't really needed. (And if we do need type information
associated with a module then we should make it explicit and not
use hacks.)
- Remove locking of the softc in the attach method, instead depending on
bus_setup_intr being at the end of attach (delaying interrupt enable until
after ether_ifattach is called)
- Call *_detach directly in the error case of attach, depending on checking
in detach to only free resources that were allocated. This puts all
resource freeing in one place, avoiding thinkos that lead to memory leaks.
- Add bus_child_present check to calls to *_stop in the detach method to
be sure hw is present before touching its registers.
- Remove bzero softc calls since device_t should do this for us.
- dc: move interrupt allocation back where it was before. It was unnecessary
to move it. This reverts part of 1.88
- rl: move irq allocation before ether_ifattach. Problems might have been
caused by allocating the irq after enabling interrupts on the card.
- rl: call rl_stop before ether_ifdetach
- sf: call sf_stop before ether_ifdetach
- sis: add missed free of sis_tag
- sis: check errors from tag creation
- sis: move dmamem_alloc and dmamap_load to happen at same time as tag creation
- sk: remove duplicate initialization of sk_dev
- ste: add missed bus_generic_detach
- ti: call ti_stop before ether_ifdetach
- ti: add missed error setting in ti_rdata alloc failure
- vr: add missed error setting in I/O, memory mapping cases
- xl: add missed error setting in I/O, memory mapping cases
- xl: remove multi-level goto on attach failure
- xl: move dmamem_alloc and dmamap_load to happen at same time as tag creation
- Calls to free(9) are unconditional because it is valid to call free with a
null pointer.
Reviewed by: imp, mdodd
o use if_input for input packet processing
o don't strip the Ethernet header for input packets
o use BPF_* macros bpf tapping
o call ether_ioctl to handle default ioctl case
o track vlan changes
Reviewed by: many
Approved by: re
most cases NULL is passed, but in some cases such as network driver locks
(which use the MTX_NETWORK_LOCK macro) and UMA zone locks, a name is used.
Tested on: i386, alpha, sparc64
something: offset into the first mbuf of the target chain before copying
the source data over.
Make drivers using m_devget() with a first argument "data - ETHER_ALIGN"
to use the offset argument to pass ETHER_ALIGN in. The way it was previously
done is potentially dangerous if the source data was at the top of a page
and the offset caused the previous page to be copied (if the
previous page has not yet been appropriately mapped).
The old `offset' argument in m_devget() is not used anywhere (it's always
0) and dates back to ~1995 (and earlier?) when support for ethernet trailers
existed. With that support gone, it was merely collecting dust.
Tested on alpha by: jlemon
Partially submitted by: jlemon
Reviewed by: jlemon
MFC after: 3 weeks
use TAILQ macros. The sk_attach_xmac() routine calls sk_init_xmac()
before doing the transceiver probe, but *before* ether_ifattach()
is called. This causes sk_init_xmac() to call sk_setmulti(), which
tries to do a TAILQ_FOREACH(), which it can't do because ether_ifattach()
hasn't done a TAILQ_INIT() yet. This causes a NULL pointer dereference
and panic in sk_setmulti() at driver load/initialization time.
Fixed by calling ether_ifattach() before the MII probe.
The code in RELENG_4 still uses the old way of enumerating the
multicast list and doesn't have this problem. Yet.
- Use pci_get_powerstate()/pci_set_powerstate() in all the other drivers
that need them so we don't have to fiddle with the PCI power management
registers directly.
- Use pci_enable_busmaster()/pci_enable_io() to turn on busmastering and
PIO/memory mapped accesses.
- Add support to the RealTek driver for the D-Link DFE-530TX+ which has
a RealTek 8139 with its own PCI ID. (Submitted by Jason Wright)
- Have the SiS 900/National DP83815 driver be sure to disable PME
mode in sis_reset(). This apparently fixes a problem on some
motherboards where the DP83815 chip fails to receive packets.
(Submitted by Chuck McCrobie <mccrobie@cablespeed.com>)
mtx_enter(lock, type) becomes:
mtx_lock(lock) for sleep locks (MTX_DEF-initialized locks)
mtx_lock_spin(lock) for spin locks (MTX_SPIN-initialized)
similarily, for releasing a lock, we now have:
mtx_unlock(lock) for MTX_DEF and mtx_unlock_spin(lock) for MTX_SPIN.
We change the caller interface for the two different types of locks
because the semantics are entirely different for each case, and this
makes it explicitly clear and, at the same time, it rids us of the
extra `type' argument.
The enter->lock and exit->unlock change has been made with the idea
that we're "locking data" and not "entering locked code" in mind.
Further, remove all additional "flags" previously passed to the
lock acquire/release routines with the exception of two:
MTX_QUIET and MTX_NOSWITCH
The functionality of these flags is preserved and they can be passed
to the lock/unlock routines by calling the corresponding wrappers:
mtx_{lock, unlock}_flags(lock, flag(s)) and
mtx_{lock, unlock}_spin_flags(lock, flag(s)) for MTX_DEF and MTX_SPIN
locks, respectively.
Re-inline some lock acq/rel code; in the sleep lock case, we only
inline the _obtain_lock()s in order to ensure that the inlined code
fits into a cache line. In the spin lock case, we inline recursion and
actually only perform a function call if we need to spin. This change
has been made with the idea that we generally tend to avoid spin locks
and that also the spin locks that we do have and are heavily used
(i.e. sched_lock) do recurse, and therefore in an effort to reduce
function call overhead for some architectures (such as alpha), we
inline recursion for this case.
Create a new malloc type for the witness code and retire from using
the M_DEV type. The new type is called M_WITNESS and is only declared
if WITNESS is enabled.
Begin cleaning up some machdep/mutex.h code - specifically updated the
"optimized" inlined code in alpha/mutex.h and wrote MTX_LOCK_SPIN
and MTX_UNLOCK_SPIN asm macros for the i386/mutex.h as we presently
need those.
Finally, caught up to the interface changes in all sys code.
Contributors: jake, jhb, jasone (in no particular order)
