completely skipping them, create ahcich devices for them to allocate unit
numbers, but mark them as disabled to prevent driver probe and attach.
Last time some BIOSes tend to report unused channels as "not implemented".
This change makes ahcichX devices numbering consistent, independently of
connected disks. It makes per-channel driver hints usable and CAM devices
wiring possible on such systems.
I/O from userspace, capable of line rate at 10G, see
http://info.iet.unipi.it/~luigi/netmap/
At this time I am bringing in only the generic code (sys/dev/netmap/
plus two headers under sys/net/), and some sample applications in
tools/tools/netmap. There is also a manpage in share/man/man4 [1]
In order to make use of the framework you need to build a kernel
with "device netmap", and patch individual drivers with the code
that you can find in
sys/dev/netmap/head.diff
The file will go away as the relevant pieces are committed to
the various device drivers, which should happen in a few days
after talking to the driver maintainers.
Netmap support is available at the moment for Intel 10G and 1G
cards (ixgbe, em/lem/igb), and for the Realtek 1G card ("re").
I have partial patches for "bge" and am starting to work on "cxgbe".
Hopefully changes are trivial enough so interested third parties
can submit their patches. Interested people can contact me
for advice on how to add netmap support to specific devices.
CREDITS:
Netmap has been developed by Luigi Rizzo and other collaborators
at the Universita` di Pisa, and supported by EU project CHANGE
(http://www.change-project.eu/)
The code is distributed under a BSD Copyright.
[1] In my opinion is a bad idea to have all manpage in one directory.
We should place kernel documentation in the same dir that contains
the code, which would make it much simpler to keep doc and code
in sync, reduce the clutter in share/man/ and incidentally is
the policy used for all of userspace code.
Makefiles and doc tools can be trivially adjusted to find the
manpages in the relevant subdirs.
controllers.
More and more RealTek controllers started to implement EEE feature.
Vendor driver seems to load a kind of firmware for EEE with
additional PHY fixups. It is known that the EEE feature may need
ASPM support. Unfortunately there is no documentation for EEE of
the controller so enabling ASPM may cause more problems.
Unnecessarily complex LE format used on Marvell controller was
main reason not to enable 64bit DMA addressing in driver. If high
32bit address of DMA address of TX/RX buffer is changed, driver has
to generate a new LE. In TX path, driver will keep track of lastly
used high 32bit address of DMA address and generate a new LE
whenever it sees high address change in the DMA address. In RX path,
driver will always use two LEs to specify 64bit DMA address of RX
buffer. If the high 32bit address of DMA address of RX buffer is
the same as previous DMA address of RX buffer, driver does not have
to use two LEs but driver will use two LEs for simplicity in RX
ring management.
One of draw back for switching to 64bit DMA addressing is that the
large amount of LEs are used to specify 64bit DMA address such that
number of available LEs for TX/RX buffers are considerably reduced.
To mitigate the issue, increase number of available LEs from 256 to
384 for TX and from 256 to 512 for RX. For 32bit architectures,
msk(4) does not use 64bit DMA addressing to save resources.
Tested by: das
based on Solarflare SFC9000 family controllers. The driver supports jumbo
frames, transmit/receive checksum offload, TCP Segmentation Offload (TSO),
Large Receive Offload (LRO), VLAN checksum offload, VLAN TSO, and Receive Side
Scaling (RSS) using MSI-X interrupts.
This work was sponsored by Solarflare Communications, Inc.
My sincere thanks to Ben Hutchings for doing a lot of the hard work!
Sponsored by: Solarflare Communications, Inc.
MFC after: 3 weeks
can be enabled via the hw.mfi.msi tunable. Many mfi(4) controllers also
support MSI-X, but in testing it seems that many adapters do not work with
MSI-X but do work with MSI.
MFC after: 2 weeks
is actually broken, or needs a BIOS upgrade for 64 bit loads, but this uncovered
a couple of misplaced opcode definitions and some missing continual mbox command
cases, so might as well update them here.
maximum IP datagram size (65535 bytes) +
Ethernet header size (14 bytes) +
2 * VLAN tag size (4 bytes) [1].
[1] We need to multiply by 2 to account for the double VLAN tag
provision added in IEEE 802.1ad.
Submitted by: David Somayajulu (david.somayajulu qlogic.com)
MFC after: 4 days
curthread-accessing part of mtx_{,un}lock(9) when using a r210623-style
curthread implementation on sparc64, crashing the kernel in its early
cycles as PCPU isn't set up, yet (and can't be set up as OFW is one of the
things we need for that, which leads to a chicken-and-egg problem). What
happens is that due to the fact that the idea of r210623 actually is to
allow the compiler to cache invocations of curthread, it factors out
obtaining curthread needed for both mtx_lock(9) and mtx_unlock(9) to
before the branch based on kobj_mutex_inited when compiling the kernel
without the debugging options. So change kobj_class_compile_static(9)
to just never acquire kobj_mtx, effectively restricting it to its
documented use, and add a kobj_init_static(9) for initializing objects
using a class compiled with the former and that also avoids using mutex(9)
(and malloc(9)). Also assert in both of these functions that they are
used in their intended way only.
While at it, inline kobj_register_method() and kobj_unregister_method()
as there wasn't much point for factoring them out in the first place
and so that a reader of the code has to figure out the locking for
fewer functions missing a KOBJ_ASSERT.
Tested on powerpc{,64} by andreast.
Reviewed by: nwhitehorn (earlier version), jhb
MFC after: 3 days
- Don't use a single big DMA block for all rings. Create separate
DMA area for each ring instead. Currently the following DMA
areas are created:
Event ring, standard RX ring, jumbo RX ring, RX return ring,
hardware MAC statistics and producer/consumer status area.
For Tigon II, mini RX ring and TX ring are additionally created.
- Added missing bus_dmamap_sync(9) in various TX/RX paths.
- TX ring is no longer created for Tigon 1 such that it saves more
resources on Tigon 1.
- Data sheet is not clear about alignment requirement of each ring
so use 32 bytes alignment for normal DMA area but use 64 bytes
alignment for jumbo RX ring where the extended RX descriptor
size is 64 bytes.
- For each TX/RX buffers use separate DMA tag(e.g. the size of a
DMA segment, total size of DMA segments etc).
- Tigon allows separate DMA area for event producer, RX return
producer and TX consumer which is really cool feature. This
means TX and RX path could be independently run in parallel.
However ti(4) uses a single driver lock so it's meaningless
to have separate DMA area for these producer/consumer such that
this change creates a single status DMA area.
- It seems Tigon has no limits on DMA address space and I also
don't see any problem with that but old comments in driver
indicates there could be issues on descriptors being located in
64bit region. Introduce a tunable, dev.ti.%d.dac, to disable
using 64bit DMA in driver. The default is 0 which means it would
use full 64bit DMA. If there are DMA issues, users can disable
it by setting the tunable to 0.
- Do not increase watchdog timer in ti_txeof(). Previously driver
increased the watchdog timer whenever there are queued TX frames.
- When stat ticks is set to 0, skip processing ti_stats_update(),
avoiding bus_dmamap_sync(9) and updating if_collisions counter.
- MTU does not include FCS bytes, replace it with
ETHER_VLAN_ENCAP_LEN.
With these changes, ti(4) should work on PAE environments.
Many thanks to Jay Borkenhagen for remote hardware access.
have administrators control them. ti(4) provides a character
device to control various other features of driver via ioctls but
users had to write their own code to manipulate these parameters.
It seems some default values for these parameters are not optimal
on today's system but leave it as it was and let administrators
change them. The following parameters could be changed:
dev.ti.%d.rx_coal_ticks
dev.ti.%d.rx_max_coal_bds
dev.ti.%d.tx_coal_ticks
dev.ti.%d.tx_max_coal_bds
dev.ti.%d.tx_buf_ratio
dev.ti.%d.stat_ticks
The interface has to be brought down and up again before a change
takes effect.
ti(4) controller supports hardware MAC counters with additional
DMA statistics. So it's doable to export these counters via
sysctl interface. Unfortunately, these counters are cumulative
such that driver have to either send an explicit clear command to
controller after extracting them or have to maintain internal
counters to get actual changes. Neither look good to me so
counters were not exported via sysctl.
Pre-allocate the memory in device attach time. While I'm here
remove unnecessary reassignment of error variable as it was already
initialized. Also added a missing driver lock in TIIOCSETTRACE
handler.
cp2103 usb-to-serial chip.
- This patch also makes the line status polling asynchronous, to reduce
the time needed to change the GPIO pins.
Submitted by: JD Louw
MFC after: 1 week
- Make it easier to port the USB code to other platforms by only using
one set of memory functions for clearing and copying memory. None of
the memory copies are overlapping. This means using bcopy() is not
required.
- Fix a compile warning when USB_HAVE_BUSDMA=0
- Add missing semicolon in avr32dci.
- Update some comments.
MFC after: 1 week
if_alloctype was used to store the origional interface type. Take
advantage of this change by removing all existing uses of if_free_type()
in favor of if_free().
MFC after: 1 Month
- fix other errors introduced when committing r226436
- add 'function' to a sentence where it makes sense
Submitted by: delphij
Submitted by: dougb
Submitted by: jhb
Approved by: dougb
Approved by: jhb
the length of frame should be treated as multiple of 4. Actual
frame length is set in the TX header. The TX header position
should be aligned on 4 byte boundary and actual frame start
position should be aligned on 4 byte boundary as well. This means
we need 4(TX header length) + 3(frame length fixup) additional free
space in TX buffer in addition to actual frame length.
Make sure TX handler check these additional bytes.
ae_tx_avail_size() returns actual free space in TX buffer to ease
the calculation of available TX buffer space in caller. While I'm
here, replace magic number to appropriate sizeof operator to
enhance readability.
This change should fix controller lockup issue happened under
certain conditions but it still does not fix watchdog timeout. It
seems the watchdog timeout is side-effect of TxS and TxD
mismatches. The root cause of TxD/TxD mismatch is not known yet but
it looks like silicon bug. I guess driver may have to reinitialize
controller whenever it sees TxS and TxD mismatches but leave it as
it was at this moment.
PR: kern/145918
I need to investigate this a little closer, but it seems that in noisy
environments the NF load takes longer than 5 * DELAY(10) and this is
messing up future NF calibrations. (The background: NF calibrations
begin at the value programmed in after the load has completed, so
if this is never loaded in, the NF calibrations only ever start at
the currently calibrated NF value, rather than starting at something
high (say -50.)
More investigation about the effect on 11n RX and calibration results
are needed.
Sponsored by: Hobnob, Inc.
The AR5416 MAC (which shows up in the AR5008, AR9001, AR9002 devices) has
issues with PCI transactions on SMP machines. This work-around enforces
that register access is serialised through a (global for now) spinlock.
This should stop the hangs people have seen with the AR5416 PCI devices
on SMP hosts.
Obtained by: Linux, Atheros
ensuring that everything is really, truly consistent.
This fixes certain cases where one will see various:
mfi0: COMMAND 0xffffffXXXXXXXXXX TIMEOUT AFTER XX SECONDS
MFC after: 3 days
Submitted by: scottl
Ok'ed by: jhb
it's cloned and that clone is retransmitted. This means that the
ath_buf pointer squirreled away on the baw window array is suddenly
wrong and was causing all kinds of console output.
This updates the pointer in that particular BAW slot to the new
ath_buf after ensuring that:
* the new and old buffers have the same seqno;
* the current slot pointer matches the old buffer pointer.
This quietens the debugging output (again), restoring said debugging
to only signify when a broken condition has occured.
Sponsored by: Hobnob, Inc.
This is a bit hackish and should be made more generic (ie, support more than
two hard-coded performance counter+config register pairs) so it can be used
for mips74k and other chips.
All this does is process the initial interrupt event. It doesn't (yet) handle
callgraph events, so even if you route the exception/interrupt to this routine
and flip the bit on, it will hang and crash pmc unless you disable callgraph
support when you enable a sample based PMC.
