as we have no use for that info. Instead let this function return the
keyboard ID and verify at its invocation in sunkbd_configure() that we're
talking to a Sun type 4/5/6 keyboard, i.e. a keyboard supported by this
driver.
- Add an option SUNKBD_EMULATE_ATKBD whose code is based on the respective
code in ukbd(4) and like UKBD_EMULATE_ATSCANCODE causes this driver to
emit AT keyboard/KB_101 compatible scan codes in K_RAW mode as assumed by
kbdmux(4). Unlike UKBD_EMULATE_ATSCANCODE, SUNKBD_EMULATE_ATKBD also
triggers the use of AT keyboard maps and thus allows to use the map files
in share/syscons/keymaps with this driver at the cost of an additional
translation (in ukbd(4) this just is the way of operation).
- Implement an option SUNKBD_DFLT_KEYMAP, which like the equivalent options
of the other keyboard drivers allows to specify the default in-kernel
keyboard map. For obvious reasons this made to only work when also using
SUNKBD_EMULATE_ATKBD.
- Implement sunkbd_check(), sunkbd_check_char() and sunkbd_clear_state(),
which are also required for interoperability with kbdmux(4).
- Implement K_CODE mode and FreeBSD keypad compose.
- As a minor hack define KBD_DFLT_KEYMAP also in the !SUNKBD_EMULATE_ATKBD
case so we can obtain fkey_tab from <dev/kbd/kbdtables.h> rather than
having to duplicate it and #ifdef some more code.
- Don't use the TX-buffer for writing the two command bytes for setting the
keyboard LEDs as this consequently requires a hardware FIFO that is at
least two bytes in depth, which the NMOS-variant of the Zilog SCCs doesn't
have. Thus use an inlined version of uart_putc() to consecutively write
the command bytes (a cleaner approach would be to do this via the soft
interrupt handler but that variant wouldn't work while in ddb(4)). [1]
- Fix some minor style(9) bugs.
PR: 90316 [1]
Reviewed by: marcel [1]
BIO_READ/BIO_WRITE is sent to vnode-backed provider (BIO_DELETE or
BIO_FLUSH).
Reported by: ceri
Add support for BIO_FLUSH to vnode-backed md(4) devices based on
VOP_FSYNC().
- Test the mac_type rather than if_hwassist (since ifp doesn't exist yet)
to determine if the adapter supports TSO and thus to change the sizes
for the bus_dma tag.
Reviewed by: glebius
during detach() similar to other NIC drivers rather than allocating them
during init() and freeing them during stop():
- Move creation of tx bus_dma tag amd maps and tx_buffer_area from
em_setup_transmit_structures() to em_allocate_transmit_structures().
- Call em_allocate_xxx_structures() in em_attach().
- Only call em_free_xxx_structures() in em_detach().
- Change em_setup_xxx_structures() to free any existing tx or rx buffers
and in the case of rx repopulate the ring with newer buffers.
Reviewed by: jfv
the EOP descriptor in the first descriptor of the packet. And then
in em_txeof() search for DD bits set only in the EOP descriptors,
embedding the cleanup of all packet's descriptors into inner loop.
This change is important for future chips, where DD bit is going
to be set only on the EOP descriptors.
Submitted by: jfv
Details:
o if_em.c changes:
- Added several new PCI ids.
- Check em_check_phy_reset_block() before doing SIOCSIFMEDIA ioctl.
- Don't touch TARC registers, they are now handled in shared
code in if_em_hw.c.
- Move RDH and RDT setting to the end of
em_initialize_receive_unit().
- Declare em_read_pcie_cap_reg(), now empty.
o if_em_hw.c dropped in from vendor, then restored rev. 1.15.
o if_em_hw.h dropped in from vendor, then modified:
- Added RX overrun interrupt flag to interrupt enable mask.
- Remove declarations of em_io_read(), em_io_write().
Approved by: jfv
the CAM_NEW_TRAN_CODE that has been in the tree for some years now.
This first step consists solely of adding to or correcting
CAM_NEW_TRAN_CODE pieces in the kernel source tree such
that a both a GENERIC (at least on i386) and a LINT build
with CAM_NEW_TRAN_CODE as an option will compile correctly
and run (at least with some the h/w I have).
After a short settle time, the other pieces (making
CAM_NEW_TRAN_CODE the default and updating libcam
and camcontrol) will be brought in.
This will be an incompatible change in that the size of structures
related to XPT_PATH_INQ and XPT_{GET,SET}_TRAN_SETTINGS change
in both size and content. However, basic system operation and
basic system utilities work well enough with this change.
Reviewed by: freebsd-scsi and specific stakeholders
only those bars that had addresses assigned by the BIOS and where the
bridges were properly programmed. Now even unprogrammed ones work.
This was needed for sun4v. We still only implement up to 2GB memory
ranges, even for 64-bit bars. PCI standards at least through 2.2 say
that this is the max (or 1GB is, I only know it is < 32bits).
o Always define pci_addr_t as uint64_t. A pci address is always 64-bits,
but some hosts can't address all of them.
o Preserve the upper half of the 64-bit word during resource probing.
o Test to make sure that 64-bit values can fit in a u_long (true on some
platforms, but not others). Don't use those that can't.
o minor pedantry about data sizes.
o Better bridge resource reporting in bootverbose case.
o Minor formatting changes to cope with different data types on different
platforms.
Submitted by: jmg, with many changes by me to fully support 64-bit
addresses.
Though it is named after overclocking tool for ASUS motherboards,
it is not capable to change clock ratio or CPU core voltage.
This driver exports Templature, Power output voltage, Fan RPM under
dev.acpi_aiboost.0.*.
Descriptions for these values are set to sysctl describe, which can be
get by sysctl -d.
in #ifdef __NO_STRICT_ALIGNMENT rather than #ifdef __i386__. This
means that amd64 now also uses the optimized code. [1]
While at it, fix a nearby style(9) bug.
- Remove the hw.dc_quick SYSCTL, which allowed to turn off the above
mentioned optimization, as like the equivalent and already removed
- In dc_setcfg() suppress printing a warning when forcing the receiver
and transceiver to idle state times out for chips where the status
bits in question just never change (observed in detail with DM9102A)
and therefore the warning would be highly likely false positive. [2]
- In dc_ifmedia_sts() add a missing DC_UNLOCK().
Tested by: Hans-Joerg Sirtl on amd64 [1]
PR: 82681 [2]
Obtained from: NetBSD tlp(4) [2]
MFC after: 1 week
Rename MAX_SAMPLE_RATES macro to OSS_MAX_SAMPLE_RATES. The old
macro clashed with those used in other applications and libaries
(ex: RtAudio). 4Front responded by updating their spec, so we
will follow suit.
Submitted by: ryanb
Noticed by: pointyhat/kris
new device support, and it is hoped a more stable driver for 6.2. RELEASE.
This checkin was discussed and approved today by RE, scottl, jhb, and pdeuskar
keyboard is attached only after the system has already booted.
If USB keyboard is also present, and there's no kbdmux(4), the problem
has been hiding itself because as soon as we get to multi-user, the
USB keyboard becomes an active keyboard (see devd.conf), thus marking
atkbd inactive and letting the old code initialize the keyboard.
With kbdmux(4), or if there's no USB keyboard, the atkbd keyboard is
always active, whether it's physically attached or not, thus it never
initialized itself properly on a physical attach.
To fix this, move block that initialized the keyboard on attach upper
so it doesn't depend on the (KBD_IS_ACTIVE(kbd) && KBD_IS_BUSY(kbd))
condition. Also move KBD_FOUND_DEVICE() a few lines upper so that
KDSETLED and KDSETREPEAT that follow it propagate to the controller.
MFC after: 3 days
: revision 1.27
: date: 2000/05/28 12:43:24; author: ache; state: Exp; lines: +3 -2
: Manipulate with AltGR Led (really CapsLock Led) only in K_XLATE mode, because
: all other modes not set ALKED flag and it means that CapsLock always turned
: off for them.
: Real bug example is X11 which never turn on CapsLock with Russian keyboard.
:
: PR: 18651
: Submitted by: "Mike E. Matsnev" <mike@po.cs.msu.su>
MFC after: 3 days
and TCP checksum offloading fine, it only has a problem with IP checksums on
IP fragments.. Barring a fix or workaround available from the hardware, the
real solution would be to have finer grained control in the stack over what
can and cannot be assisted in hardware.
yet to be investigated circumstances. If that happens truncate to the number
of rates that the firmware supports.
Found by: Jeremie Le Hen
Obtained from: OpenBSD (w/ changes)
MFC after: 3 days
kept unused in the ring. This check should probably be moved up to
bce_start_locked at some point, as it'll make the loop up there slightly
more efficient, and will eliminate a costly set of busdma operations when
the ring is full. But this works for now.
This makes all of my UDP torture tests work. I'll cautiously say that
it might even work for other users now. Feedback is appreciated.
If the length is zero, catch this early, instead of making dflen go negative
and letting bad things happen... We also check to see if RV (checksum) is
0, and handle that has a checksum failure...
Properly handle checksum failures by not processing read-write VPD data,
and removing all the found read-only data...
Tested by: oleg (dflen going negative)
should be easily adapted to SD 2.0 (aka SDHC), SDIO, MMC and MMCplus
cards. At the present time, there's only one bridge driver for the
ARM9 based Atmel AT91RM9200.
tasks. Since the host controllers rely on tasks to process transfer
timeouts, if a synchronous transfer from a driver was invoked from
a task and timed out, it would never complete because the single
task thread was stuck performing the synchronous transfer so couldn't
process the timeout.
This affected the axe, udav and ural drivers.
Problem hardware provided by: guido
long being DMA'ed 2 (or 1) bytes past the end of the mbuf and corrupting
random kernel memory. I had forgotten about the 2 bytes of implict
padding the firmware assumes.
Sponsored by: Myricom Inc.
- Fix the locking protocol to eliminate races between normal I/O and AENs.
- Various small improvements and usability tweaks.
Sponsored by: IronPort
Portions Submitted by: Doug Ambrisko
- Use bus_dmamap_load_mbuf_sg() to eliminate the need for the callback and
all of the extra bookkeeping associated with it.
- Eliminate the bce_dmamap_arg structure and streamline the memory allocation
routines to not need it. This does change some of the debugging messages.
- Refactor the loop that fills the buffer descriptor so that it can be done
with a single set of logic in a single loop instead of two sets of logic.
- Eliminate the need to cache and pass descriptor indexes between the start
loop and the encap function.
- Change the start loop to always check the ifnet sendq for more work.
This significantly helps the driver withstand large UDP workloads, though
it's still not perfect. I suspect the remaining work lies with handling
the OACTIVE flag, and also in possibly streamlining the interrupt handler
some. It is, however, nearly on par with the other popular gigabit drivers
in terms of stability now.
- Add entries in the uscanner.4 man page (along with missing 3500).
PR: usb/100957 [1], usb/100992 [2]
Submitted by: Jim Teresco <terescoj@teresco.org> [1],
Walter C. Pelissero <walter.pelissero@iesy.net> [2]
MFC after: 3 days
will fix a problem where you boot w/ the default of autoselect, but then
set the speed to 100/full, the switch will keep the autoselect/100/full
negotiation... This will continue to work till someone resets the switch
or unplugs the cable resulting in the switch failing to autoneg and falling
back to 100/half, causing a hard to track down duplex mismatch..
Submitted by: nCircle Network Security, Inc.
MFC after: 1 week
- Add support for the Conexant Waikiki/CX20551-22, found
in most Toshiba P100 series laptops. Despite of growing
urban legend of "unsupported Conexant", this codec is fully
supported in this driver.
Note: Toshiba P100 has broken (acpi) BIOS, thus rendering
its soundchip useless. Please disable ACPI, or get
BIOS updates (if any).
Found/tested by: Vulpes Velox <v.velox@vvelox.net>
URL: http://lists.freebsd.org/pipermail/freebsd-multimedia/2006-September/004896.html
- Parser cleanups to handle possible oss/mixer collision. Found
after parsing Conexant Waikiki nodes.
- Increase resilient against resource failure during attach/detach.
- Implement simple config through hint.pcm.<unit>.config. Supported
options:
gpio0 (default on Acer), gpio1, gpio2, softpcmvol,
fixedrate (default), forcestereo (default)
* Option prefixed with "no" (such as "nofixedrate") will do
the opposite.
* Options can be separated using space " " or comma ",".
* The "no" option will take precedence over anything else.
Example:
hint.pcm.0.config="gpio2,nofixedrate,noforcestereo,nogpio0,softpcmvol"
hint.pcm.0.config="softpcmvol noforcestereo"
or not the OS has to wait for RX_RDY or TX_RDY to be set before the OS sets
the control code in the control/status register. Looking at the interface
design, it seems that RX_RDY and TX_RDY are probably there to protect
access to the data register and have nothing to do with the control/status
register. Nevertheless, try to take what I think is the more conservative
approach and always wait for the appropriate [TR]X_RDY flag to be set
before writing any of the WR_NEXT, WR_END, RD_START, or RD_NEXT control
codes to the control/status register.
close and re-open the default pipe instead of relying on the host
controller driver to notice the changes. Remove the unreliable code
that attempted to update these fields while the pipe was active.
This fixes a case where the hardware could cache and continue to
use the old address, resulting in a "getting first desc failed"
error.
PR: usb/103167
- Fix support for ASUS M5200ae (buggy BIOS)
- Fix few problems, reported by Coverity Prevent (TM).
CID: 246991, 246676, 246675, 246674, 246477
Found by: Coverity Prevent (TM)
The parallel LINT build sometimes broke if kernel-depend wasn't
fast enough in generating ukbdmap.h. If someone thinks this
option would still be useful for the module, a proper fix is
to add the code generating ukbdmap.h into modules/ukbd/Makefile
and backing this change out.
