- use ATA_SE_EXCHANGED (SError.DIAG.X) bit to detect hot-plug events when
power-management enabled and ATA_SE_PHY_CHANGED (SError.DIAG.N) can't be
trusted;
- on controllers supporting staggered spin-up (SS) put unused channels
into Listen state instead of Off. It should still save some power, but
allow plug-in events to be detected;
- on controllers supporting cold presence detection (CPD), when power
management enabled, use CPD events to detect hot-plug in addition to PHY
events.
down. The ingress queue lock was unused and has been removed as part of
these changes.
- An in-flight egress update from the SGE must be handled before the
queue that requested it is destroyed. Wait for the update to arrive.
- Interrupt handlers must stop processing rx events for a queue before
the queue is destroyed. Events that have not yet been processed
should be ignored once the queue disappears.
MFC after: 1 week
from scratch. Remove htole16() calls, rxon.chan is an uint8_t,
ieee80211_chan2ieee() does return an ic_ieee as an int, but I heavily
doubt a htole16() will buy us anything here.
- IWN_TXOP_TO_US is equal to IEEE80211_TXOP_TO_US
- use IEEE80211_DUR_TU
- ieee80211_add_rates/ieee80211_add_xrates are public, use em
- copied ieee80211_add_ssid it is not public
Instead of spinning in a tight loop for up to 15 seconds, polling for device
readiness while it spins up, return reset completion just after PHY reports
"connect well" or 100ms connection timeout. If device was found, use callout
for checking device readiness with 100ms period up to full 31 second timeout.
This fixes system freeze for 5-10 seconds on drives hot plug-in.
- make SATA SIMs announce capabilities to handle SDB with Notification bit;
- make PMP driver honor this SIMs capability;
- make SATA XPT to negotiate and enable this feature for ATAPI devices.
This feature allows supporting SATA ATAPI devices to inform system about
some events happened, that may require attention. In my case this allows
LG GH22LS50 SATA DVR-RW drive to report tray open/close events. Events
reported to CAM in form of AC_SCSI_AEN async. Further they could be used
as a hints for checking device status and reporting media change to upper
layers, for example, via spoiling mechanism of GEOM.
diversity.
This is bit dirty and likely should be revised at a later date,
with an eye to unifying/tidying up the whole diversity setup
and allowing developers to do "tricky stuff" as they desire.
For now, this works.
* add a new method, specifically for doing per-RX packet
antenna diversity
* set that HAL method only if it's Kite and a Kite chip that
does diversity.
* add a diversity flag to the HAL debugging section
* add a check to make sure the kite diversity code doesn't run
on boards that don't require it, as not all Kite chips will
implement it.
* add some debug statements when the diversity code makes
changes to the antenna diversity/combining setup.
controller port readiness (that should set just after PHY ready signal),
reduce wait time from 10s to 1s before trying more aggressive reset method.
This should improve system responsibility in some failure conditions.
Note: this HAL currently only supports the AR9285.
From Linux ath9k:
The problem is that when the attenuation is increased,
the rate will start to drop from MCS7 -> MCS6, and finally
will see MCS1 -> CCK_11Mbps. When the rate is changed b/w
CCK and OFDM, it will use register desired_scale to calculate
how much tx gain need to change.
The output power with the same tx gain for CCK and OFDM modulated
signals are different. This difference is constant for AR9280
but not AR9285/AR9271. It has different PA architecture
a constant. So it should be calibrated against this PA
characteristic.
The driver has to read the calibrated values from EEPROM and set
the tx power registers accordingly.
Instead of spinning in a tight loop for up to 15 seconds, polling for device
readiness while it spins up, return reset completion just after PHY reports
"connect well" or 100ms connection timeout. If device was found, use callout
for checking device readiness with 100ms period up to full 31 second timeout.
This fixes system freeze for 5-10 seconds on drives hot plug-in.
bus driver at detach, hence ehci_detach() does exactly this since r199718.
Submitted by: Luiz Otavio O Souza
MFC after: 7 days
Approved by: thompsa (mentor)
SCSI status errors to CAM (that was wrong, as it too often turned retriable
wire errors into non-retriable REQUEST SENSE errors), do it only for STALL
errors on control pipe of the CBI devices. STALL on control pipe is just
a one of the ways to report error for CBI devices.
PR: usb/150401, usb/154593.
Reviewed by: hselasky
MFC after: 1 week
ctl/ext noise floor values.
This routine doesn't check to see whether the radio is MIMO
capable - instead, it simply returns either the raw values,
the "nominal" values if the raw values aren't yet available
or are invalid, or '0' values if there's no valid channel/
no valid MIMO values.
Callers are expected to verify the radio is a MIMO radio
(which for now means it's an 11n chipset, there are non-11n
MIMO chipsets out there but I don't think we support them,
at least in MIMO mode) before exporting the MIMO values.
upper-level HAL.
Right now the per-chain noise floor values aren't used anywhere in
the upper-level HAL, so the driver currently has no real reference
to compare the per-chain RSSI values to.
This is needed before per-chain RSSI values (for ctl and ext radios)
are can be thrown upstairs to the net80211 code.
safer for i386 because it can be easily over 4 GHz now. More worse, it can
be easily changed by user with 'machdep.tsc_freq' tunable (directly) or
cpufreq(4) (indirectly). Note it is intentionally not used in performance
critical paths to avoid performance regression (but we should, in theory).
Alternatively, we may add "virtual TSC" with lower frequency if maximum
frequency overflows 32 bits (and ignore possible incoherency as we do now).
chain to be corrupted.
- Removed many console print warnings and replaced with driver maintained
counters.
- Several style(9) fixes.
MFC after: One week.
improves command timeout handling.
Many thanks to Areca for continuing to support FreeBSD.
Submitted by: Ching-Lung Huang <ching2048 areca com tw>
MFC after: 2 months
This fixes a long standing bug in mxge(4) where "ifconfig mxge0 $IP"
did not bring the interface into a RUNNING state, like it does on
most (all?) other FreeBSD NIC drivers.
Thanks to gnn for mentioning the bug, and yongari for pointing out that
ether_ioctl() invokes ifp->if_init() in SIOCSIFADDR.
MFC after: 7 days
- Add the change made in em to the actual unrefreshed number
of descriptors is used as a basis in rxeof on the way out
to determine if more refresh is needed. NOTE: there is a
difference in the ring setup in igb, this is not accidental,
it is necessitated by hardware behavior, when you reset the
newer adapters it will not let you write RDH, it ALWAYS sets
it to 0. Thus the way em does it is not possible.
- Change the sysctl handling of flow control, it will now make
the change dynamically when the variable setting changes rather
than requiring a reset.
- Change the eee sysctl naming, validation found the old unintuitive :)
- Last but not least, some important performance tweaks in the TX
path, I found that UDP behavior could be drastically hindered or
improved with just small changes in the start loop. What I have
here is what testing has shown to be the best overall. Its interesting
to note that changing the clean threshold to start at a full half of
the ring, made a BIG difference in performance. I hope that this
will prove to be advantageous for most workloads.
MFC in a week.
show that there are perfectly working PM timers with occasional "hiccups",
probably because of an SMI. Now we ignore the maximum if it happens once in
the test loop and the width is small enough. Also, relax normal width a bit
to count in a boundary case.
Unlike other controllers which have more advanced jumbo support,
these controllers have one send ring, one standard receive producer
ring and one receive return ring. In order to receive jumbo frames
on the controllers, driver now will increase Rx buffer size to 9k.
Two Rx modes are supported on these controllers and I chose
standard Rx BDs over extended Rx BDs. The extended Rx BD mode
allows up to 4 segmentations for each Rx BDs such that kernel does
not have to allocate large buffer of contiguous memory for
receiving. The extended Rx BD mode is already used on controllers
that have separate jumbo receive ring. However, using extended Rx
BDs on BCM5714/BCM5715/BCM5780 reduces the number of Rx BDs to 256
entries which in turn may reduce the performance. Also UMA backed
page allocator for jumbo frame returns contiguous memory so using
extended Rx BD has no advantage on FreeBSD unless highly customized
local allocator implemented in driver is used.
To use jumbo buffers in standard receive ring, Rx buffer allocation
handler was changed to allocate MJUM9BYTES sized mbuf.
PR: kern/155192
Tested by: Vijay Singh <vijju.singh <> gmail dot com>
Submitted by: mjacob (initial version)
