This is a minor cosmetic change - the users are more likely to want to
increase (rather than decrease) default kernel stack size,
which is already 4 pages on amd64.
MFC after: 4 days
Linux ath9k.
The ath9k ar9002_hw_init_cal() isn't entirely clear about what
is supposed to be called for what chipsets, so I'm ignoring the
rest of it and just porting the AR9285 init cal path as-is and
leaving the rest alone. Subsequent commits may also tidy up the
Merlin (AR9285) and other chipset support.
Obtained from: Linux ath9k
The ath9k driver has a unified boundary/pdadc function, whereas
ours is split into two (one for each EEPROM type.) This is why
the AR9280 check is done here where we could safely assume it'll
always be AR9280 or later.
this is incorrect for Kite (AR9285) and any future chipsets that
override the EEPROM related routines.
It meant that a direct call to set the TX power would call the v14 EEPROM
AR5416/AR9280 calibration routines, rather than the v4k EEPROM routines
for the AR9285. It thus read the incorrect values from the EEPROM and
programmed garbage PDADC and TX power values into the hardware.
c65292b04b98d6a76d58c5a54ca8f81463bf24de to support new SIOCGIFDESCR
ioctl interface which was too late for libpcap 1.1.1.
Reported by: brucec
Noticed by: wxs
The test was support to check if SUID/SGID bits are removed on first
write, but actually we were checking if they were removed after close.
Now we can check if SUID/SGID bits are gone after first write.
While here add checks to see if when both SUID and SGID bits are set they are
both cleared on first write.
adjust the IEEE80211_HTRATE_MAXSIZE constant, only MCS0 - 76 are valid
the other bits in the mcsset IE (77 - 127) are either reserved or used
for TX parameters.
o bunch of variables are turned into uint8_t
o initial setting of namep[] in lookup() is removed
as it's only overwritten a few lines down
o kname is explicitly initialized in main() as BSS
in boot2 is not zeroed
o the setting and reading of "fmt" in load() is removed
o buf in printf() is made static to save space
Reviewed by: jhb
Tested by: me and Fabian Keil <freebsd-listen fabiankeil de>
This makes partitions between 50GiB and 2TiB (16TiB for 4k drives) print
correctly aligned.
While here, fix type of secsize. g_sectorsize() returns ssize_t, don't
store this in an unsigned var. Bump WARNS to 6.
MFC after: 4 weeks
- the default label now includes an a: partition by default
- the c: partition is no longer exported via devfs
- writing of the labels usually works in all cases, though the script
assumes half of them have to fail
It looks like these apply in both open and closed loop TX power control,
but the only merlin boards i have either have OL -or- a non-default power
offset, not both.
to both make things clearer, and to make it easier to write userland
code which pulls in these definitions without needing to pull in the
rest of the HAL.
This stuff should be deprecated at some point in the future once
the net80211 regulatory domain support encapsulates all of the
defintions here.
This is something bus clock related from what I can gather. It is needed for
the AR9220 based Ubiquiti SR71-12 and SR71-15 Mini-PCI NICs.
(Note: those NICs don't work right now because of earlier changes to handle
power table offset correctly. That'll be resolved in a follow-up commit.)
- fchmod(2),
- fchown(2),
- fchflags(2),
- fstat(2),
- ftruncate(2),
- fpathconf(2),
- lpathconf(2).
Make write(2) syscall to take descriptor instead of file name.
We implement descriptors by keeping track of open files and allowing to
reference them by the following syscalls. Because pjdfstest already supports
executing multiple syscalls from one command it works pretty well.
For example, the following command:
pjdfstest open foo "O_CREAT,O_RDWR" 0 : open bar "O_CREAT,O_RDONLY" 640 : fchmod 0 0666 : fchown 0 -1 20 : fchmod 1 0444
is equivalent of (error checking omitted):
int fd[2];
fd[0] = open("foo", O_CREAT | O_RDWR, 0);
fd[1] = open("bar", O_CREAT | O_RDONLY, 0640);
fchmod(fd[0], 0666);
fchown(fd[0], -1, 20);
fchmod(fd[1], 0444);
