into the FreeBSD boot loader, typically for non-USB aware BIOSes, EFI systems
or embedded platforms. This is also useful for out of the system compilation
of the FreeBSD USB stack for various purposes. The USB kernel files can
now optionally include a global header file which should include all needed
definitions required to compile the FreeBSD USB stack. When the global USB
header file is included, no other USB header files will be included by
default.
Add new file containing the USB stack configuration for the
FreeBSD loader build.
Replace some __FBSDID()'s by /* $FreeBSD$ */ comments. Now all
USB files follow the same style.
Use cases:
- console in loader via USB
- loading kernel via USB
Discussed with: Hiroki Sato, hrs @ EuroBSDCon
bug in old versions of QEMU (and Xen, and other places using QEMU code).
On those buggy emulated UARTs, the "TX idle" interrupt gets lost; with
this workaround, we spinwait for the TX to happen and then send ourselves
the interrupt. It's ugly but it works, while minimizing the impact on
the code for the !broken_txfifo case.
MFC after: 2 weeks
If a BUSDMA load operation results in a single segment which
is greater than the PAGE_SIZE, the USB computed physical
addresses will not be correct. Make sure that the first
segment is unfolded like the sub-sequent segments are into
USB_PAGE_SIZE big ranges.
Found by: Alexander Nedotsukov
MFC after: 1 week
flush wait on the Gen2 chipsets. Confirmed by the inspection of the
Linux agp code.
Submitted by: Taku YAMAMOTO <taku@tackymt.homeip.net>
MFC after: 2 weeks
cannot be freed while do_pass_accept_req is running. This closes a race
where do_pass_establish on another CPU (the driver chose a different
queue for the new tid) expands the synq entry into a full PCB and then
releases the only hold on it, all while do_pass_accept_req is still
running.
MFC after: 3 days
the separate ath0 TX taskq.
Whilst here, make sure that the TX software scheduler is also
running out of the TX task, rather than the ath0 taskqueue.
Make sure that the tx taskqueue is blocked/unblocked as necessary.
This allows for a little more parallelism on multi-core machines,
as well as (eventually) supporting a higher task priority for TX
tasks, allowing said TX task to preempt an already running RX or
TX completion task.
Tested:
* AR5416, AR9280 hostap and STA modes
- Make bge_lookup_{rev,vendor}() static.
- Factor out chip identification rather than duplicating the code.
- Sanitize bge_probe() a bit (don't hardcode buffer sizes, allow
bge_lookup_vendor() to return NULL so the excessive panic() three
can be removed there, etc.) and return BUS_PROBE_DEFAULT rather than
hardcoding 0.
- According to the Linux tg3 driver, BCM57791 and BCM57795 aren't
capable of Gigabit Ethernet.
- Check the return value of taskqueue_start_threads().
- At least the Saturn chips of 501-6738 cards need a delay after freezing
the external GMII pins before the internal PHY is accessible again. So
wait a bit after (un)freezing these. Also don't touch the other bits of
that configuration register. [1]
- Take advantage of nitems().
Reported and tested by: Paul Keusemann [1]
MFC after: 3 days
By setting dev.netmap.fwd=1 (or enabling the feature with a per-ring flag),
packets are forwarded between the NIC and the host stack unless the
netmap client clears the NS_FORWARD flag on the individual descriptors.
This feature greatly simplifies applications where some traffic
(think of ARP, control traffic, ssh sessions...) must be processed
by the host stack, whereas the bulk is handled by the netmap process
which simply (un)marks packets that should not be forwarded.
The default is chosen so that now a netmap receiver operates
in a mode very similar to bpf.
Of course there is no free lunch: traffic to/from the host stack
still operates at OS speed (or less, as there is one extra copy in
one direction).
HOWEVER, since traffic goes to the user process before being
reinjected, and reinjection occurs in a user context, you get some
form of livelock protection for free.
Add a missing 0 to the mask for byte0 of C_SIZE.
The previous mask (0xc) worked except that the last 0-1536K of the disk
could not be accessed since we were shifting the (wrong) bits we did
mask off the right edge.
generating binary diffs.
- Constify a few strings used in the driver.
- Style changes to make the driver compile with default clang settings.
Approved by: HighPoint Technologies
MFC after: 3 days
This is easily possible now that the TX is protected by a single
lock, rather than a per-TXQ (and thus per-TID) lock.
Only set CLRDMASK if none of the destinations are filtered.
This likely will need some tuning when it comes time to do UASPD/PS-POLL
TX, however at that point it should be manually set anyway.
Tested:
* AR9280, STA mode
TODO:
* More thorough testing in AP mode
* test other chipsets, just to be safe/sure.
'bhyve' was developed by grehan@ and myself at NetApp (thanks!).
Special thanks to Peter Snyder, Joe Caradonna and Michael Dexter for their
support and encouragement.
Obtained from: NetApp
Make umass return an error code if SCSI sense retrieval request
has failed. Make sure scsi_error_action honors SF_NO_RETRY and
SF_NO_RECOVERY in all cases, even if it cannot parse sense bytes.
Reviewed by: hselasky (umass), scottl (cam)
two upcoming features:
semi-transparent mode:
when a device is opened in this mode, the
user program will be able to mark slots that must be forwarded
to the "other" side (i.e. from NIC to host stack, or viceversa),
and the forwarding will occur automatically at the next netmap syscall.
This saves the need to open another file descriptor and do
the forwarding manually.
direct-forwarding mode:
when operating with a VALE port, the user can specify in the slot
the actual destination port, overriding the forwarding decision
made by a lookup of the destination MAC. This can be useful to
implement packet dispatchers.
No API changes will be introduced.
No new functionality in this patch yet.
chip hangs.
* Always do a reset in ath_bmiss_proc(), regardless of whether the
hardware is "hung" or not. Specifically, for spectral scan, there's
likely a whole bunch of potential hangs that we don't (yet) recognise
in the HAL. So to avoid staying RX deaf persisting until the station
disassociates, just do a no-loss reset.
* Set sc_beacons=1 in STA mode. During a reset, the beacon programming
isn't done. (It's likely I need to set sc_syncbeacons during a hang
reset, but I digress.) Thus after a reset, there's no beacon timer
programming to send a BMISS interrupt if beacons aren't heard ..
thus if the AP disappears, you won't get notified and you'll have to
reset your interface.
This hasn't yet fixed all of the hangs that I've seen when debugging
spectral scan, but it's certainly reduced the hang frequency and it
should improve general STA stability in very noisy environments.
Tested:
* AR9280, STA mode, spectral scan off/on
PR: kern/175227
when an interface is going down.
Right now it's quite possible (but very unlikely!) that ath_reset()
or similar is called, leading to a beacon config call, in parallel with
the last VAP being destroyed.
This likely should be fixed by making sure the bmiss/bstuck/watchdog
taskqueues are canceled whenever the last VAP is destroyed.
serial devices (such as printer ports). This allows ppc devices attached
to puc to correctly setup an interrupt handler and work.
Tested by: Andre Albsmeier Andre.Albsmeier@siemens.com
MFC after: 1 week
if_start().
This removes the overlapping data path TX from occuring, which
solves quite a number of the potential TX queue races in ath(4).
It doesn't fix the net80211 layer TX queue races and it doesn't
fix the raw TX path yet, but it's an important step towards this.
This hasn't dropped the TX performance in my testing; primarily
because now the TX path can quickly queue frames and continue
along processing.
This involves a few rather deep changes:
* Use the ath_buf as a queue placeholder for now, as we need to be
able to support queuing a list of mbufs (ie, when transmitting
fragments) and m_nextpkt can't be used here (because it's what is
joining the fragments together)
* if_transmit() now simply allocates the ath_buf and queues it to
a driver TX staging queue.
* TX is now moved into a taskqueue function.
* The TX taskqueue function now dequeues and transmits frames.
* Fragments are handled correctly here - as the current API passes
the fragment list as one mbuf list (joined with m_nextpkt) through
to the driver if_transmit().
* For the couple of places where ath_start() may be called (mostly
from net80211 when starting the VAP up again), just reimplement
it using the new enqueue and taskqueue methods.
What I don't like (about this work and the TX code in general):
* I'm using the same lock for the staging TX queue management and the
actual TX. This isn't required; I'm just being slack.
* I haven't yet moved TX to a separate taskqueue (but the taskqueue is
created); it's easy enough to do this later if necessary. I just need
to make sure it's a higher priority queue, so TX has the same
behaviour as it used to (where it would preempt existing RX..)
* I need to re-review the TX path a little more and make sure that
ieee80211_node_*() functions aren't called within the TX lock.
When queueing, I should just push failed frames into a queue and
when I'm wrapping up the TX code, unlock the TX lock and
call ieee80211_node_free() on each.
* It would be nice if I could hold the TX lock for the entire
TX and TX completion, rather than this release/re-acquire behaviour.
But that requires that I shuffle around the TX completion code
to handle actual ath_buf free and net80211 callback/free outside
of the TX lock. That's one of my next projects.
* the ic_raw_xmit() path doesn't use this yet - so it still has
sequencing problems with parallel, overlapping calls to the
data path. I'll fix this later.
Tested:
* Hostap - AR9280, AR9220
* STA - AR5212, AR9280, AR5416
CISS_MAX_LOGICAL to 107
Submitter wanted to increase the number of logical disks supported by ciss(4)
by simply raising the CISS_MAX_LOGICAL value even higher. Instead, consult
the documentation for the raid controller (OPENCISS) and poke the controller
bits to ask it for how many logical/physical disks it can handle.
Revert svn R242089 that raised CISS_MAX_LOGICAL to 64 for all controllers.
For older controllers that don't support this mechanism, fallback to the old
value of 16 logical disks. Tested on P420, P410, P400 and 6i model ciss(4)
controllers.
This should will be MFC'd back to stable/9 stable/8 and stable/7 after the MFC
period.
PR: kern/151564
Reviewed by: scottl@freebsd.org
MFC after: 2 weeks
This is the Compressed Local IPv6 table on the chip. To save space, the
chip uses an index into this table instead of a full IPv6 address in
some of its hardware data structures.
For now the driver fills this table with all the local IPv6 addresses
that it sees at the time the table is initialized. I'll improve this
later so that the table is updated whenever new IPv6 addresses are
configured or existing ones deleted.
MFC after: 1 week
- Teach find_best_mtu_idx() to deal with IPv6 endpoints.
- Install correct protosw in offloaded TCP/IPv6 sockets when DDP is
enabled.
- Move set_tcp_ddp_ulp_mode to t4_tom.c so that t4_tom.h can be included
without having to drag in t4_msg.h too. This was bothering the iWARP
driver for some reason.
MFC after: 1 week
- Add full support for IPv6 addresses.
- Read the size of the L2 table during attach. Do not assume that PCIe
physical function 4 of the card has all of the table to itself.
- Use FNV instead of Jenkins to hash L3 addresses and drop the private
copy of jhash.h from the driver.
MFC after: 1 week
Implement an FDT attachment for altera_avgen(4).
Portions of the changeset updating DTS and device.hints will be merged
separately.
Sponsored by: DARPA, AFRL
Rework altera_avgen(4) to cleanly(ish) separate nexus bus
attachment from the driver itself. This should allow us to
plug in an fdt attachment more easily.
Sponsored by: DARPA, AFRL
Start restructuring of altera_avgen(4) so that it can have an FDT
attachment -- this requires first properly breaking out the current
nexus attachment from the driver implementation.
Sponsored by: DARPA, AFRL
Write FDT attachment for the Terasic MTL (multitouch LCD) driver.
Exploit the fact that FDT allows multiple memory ranges to be
assigned to a device, giving us a cleaner description than
device.hints does.
Portions of this changeset that remove mtl from BERI device.hints and
add to DTS will be merged separately.
Sponsored by: DARPA, AFRL
Add an Intel StrataFlash (isf) driver FDT attachment.
Portions of the original changeset hooking up FDT use for BERI will be
merged separately.
Sponsored by: DARPA, AFRL
unmerged BERI DTS files) to head:
Use the OFW compatible string "mips,mips4k" rather than
"mips4k,cp0" for interrupt control using MIPS4k CP0.
Suggested by: thompsa
Implement a MIPS FDT PIC decode routine to use when no PIC has been
configured, which assumes a cascade back to the nexus bus (e.g.,
the on-board CP0 interrupt management parts on the MIPS). If the
soc bus in a MIPS DTS file is declared as "mips4k,cp0"-compatible,
then this will be enabled. This is sufficient to allow IRQs to be
configured on BERI.
Sponsored by: DARPA, AFRL
This prevents quad igb card on high core machines, without any nmbcluster or
igb queue tuning wedging the boot process if all nics are configured.
Reviewed by: jfv
Approved by: pjd (mentor)
MFC after: 1 week
on the fast data path) and use them instead of frobbing the adapter lock
and busy flag directly.
Other changes made while reworking all slow operations:
- Wait for the reply to a filter request (add/delete). This guarantees
that the operation is complete by the time the ioctl returns.
- Tidy up the tid_info structure.
- Do not allow the tx queue size to be set to something that's not a
power of 2.
MFC after: 1 week
ASUS P8Z77-V board reports _AC2, _AC3 and _AC4 setpoints as 0C. With active
cooling already automatically set to _AC2, that still caused driver to print
two useless lines about temperature above _AC3 and _AC4 every ten seconds.
Three setponts of 0C is probably a board bug, but the same spam could happen
also in correct case if system is runnign not with the lowest cooling level.
false. It is right. Delete it because on the next line we catch all
'negative' cases with the test > 2, since 'negative' numbers are just
really big unsigned numbers and we do an identical action.
Factor out USB mouse and keyboard detection logic.
Reject USB keyboards which have mouse alike HID items
in their HID descriptors.
Submitted by: Matthew W
MFC after: 1 week
resources are partitioned.
- Reduce the number of virtual interfaces reserved for PF4. This leaves
spare room in the source MAC table and allows the driver to setup
filters that rewrite the source MAC address.
- Reduce the number of filters and use the freed up space for the CLIP
(Compressed Local IPv6 addresses) table. This is a prerequisite for
IPv6 TOE support which will follow separately in a series of commits.
MFC after: 1 week
This is intended to support reporting FFT results during active channel
scans, for users who would like to fiddle around with writing applications
that do both FFT visualisation _and_ AP scanning.
* add a new ioctl to enable/trigger spectral scan at channel change/reset;
* set do_spectral consistently if it's enabled, so a channel set/reset
will carry forth the correct PHY error configuration so frames
are actually received;
* for NICs that don't do spectral scan, don't bother checking the
spectral scan state on channel change/reset.
Tested:
* AR9280 - STA and scanning;
* AR5416 - STA, ensured that the SS code doesn't panic
This change was originally intended to account for test kthreads under
the nvmecontrol process, but jhb indicated it may not be safe to
associate kthreads with userland processes and this could have
unintended consequences.
I did not observe any problems with this change, but my testing didn't
exhaust the kinds of corner cases that could cause problems. It is not
that important to account for these test threads under nvmecontrol, so I
am just reverting this change for now.
On a related note, the part of this patch for <= 7.x fails compilation
so reverting this fixes that too.
Suggested by: jhb
This patch will save CPU time when the XHCI interrupt is
shared with other devices.
Only check event rings when interrupt bits are set.
Otherwise would indicate hiding possible hardware fault(s).
Tested by: sos @
Submitted by: sos @
MFC after: 1 week
__func__ and add some missing ones.
- Remove a stale comment.
- Remove unused NUM_ELEMENTS macro.
- Remove extra empty lines.
- Use DEVMETHOD_END.
- Use NULL rather than 0 for pointers.
MFC after: 3 days
- Replace incorrect function names in printf(9) strings with __func__.
- Make xctrl_shutdown_reasons table const.
- Use nitems() rather than rolling an own version.
- Use DEVMETHOD_END.
- Use NULL rather than 0 for pointers.
MFC after: 3 days
This includes the HAL routines to setup, enable/activate/disable spectral
scan and configure the relevant registers.
This still requires driver interaction to enable spectral scan reporting.
Specifically:
* call ah_spectralConfigure() to configure and enable spectral scan;
* .. there's currently no way to disable spectral scan... that will have
to follow.
* call ah_spectralStart() to force start a spectral report;
* call ah_spectralStop() to force stop an active spectral report.
The spectral scan results appear as PHY errors (type 0x5 on the AR9280,
same as radar) but with the spectral scan bit set (0x10 in the last byte
of the frame) identifying it as a spectral report rather than a radar
FFT report.
Caveats:
* It's likely quite difficult to run spectral _and_ radar at the same
time. Enabling spectral scan disables the radar thresholds but
leaves radar enabled. Thus, the driver (for now) needs to ensure
that only one or the other is enabled.
* .. it needs testing on HT40 mode.
Tested:
* AR9280 in STA mode, HT/20 only
TODO:
* Test on AR9285, AR9287;
* Test in both HT20 and HT40 modes;
* .. all the driver glue.
Obtained from: Qualcomm Atheros
perhaps due to an interrupt configuration problem, do not try to free
device ivars that have not yet have been allocated.
MFC after: 1 week
Reviewed by: gonzo
Sponsored by: DARPA, AFRL
* Finish adding the HAL capability to announce whether a NIC supports
spectral scan or not;
* Add spectral scan methods to the HAL structure;
* Add HAL_SPECTRAL_PARAM for configuration of the spectral scan logic.
The capability ID and HAL_SPECTRAL_PARAM struct are from Qualcomm
Atheros.
typically do not handle the SYNCHRONIZE_CACHE command - they either
return an error or the firmware enters a reset loop.
Reviewed by: hselasky
Approved by: rstone (co-mentor)
MFC after: 2 weeks
elements to the USB audio softc structure. This fixes a double CPU
fault when attaching USB audio devices in 10-current for i386 at
least.
MFC after: 1 week
Use a boundary of zero, hence a PAGE_SIZE boundary
is implied by all memory allocations.
Background:
Busdma has problems to allocate more than PAGE_SIZE
bytes when the boundary is PAGE_SIZE bytes too.
Initially it was thought that a boundary of PAGE_SIZE
bytes will only affect loading of DMA memory, so that
segments get split correctly, but it also affects
allocation of DMA'able memory.
Solution:
USB can detect big segments and split them as required
by the USB code.
MFC after: 1 week
Reported by: gonzo
previous names, 'ptag' and 'pmap' -- p stands for packet.
This change reduces the difference between the code in stable/9
and head, and also helps using the same ixgbe_netmap.h on both branches.
Approved by: Jack Vogel
through the USB API and/or busdma.
The following assumptions have been made:
umass - buffers passed from CAM/SCSI layer are OK
network - mbufs are OK.
Some other nits while at it.
MFC after: 1 week
Suggested by: imp
DMA data does not reside next to non DMA data. This
might cause more memory to be allocated, but solves
problems on platforms using manual cache
synchronization.
Add a convenience function to get the buffer only
from a USB transfer's page cache structure.
MFC after: 1 week
Suggested by: imp
Unfortunately 5720S uses 5709S PHY id so add a hack to detect 5720S
PHY by checking parent device name. 5720S PHY does not support 2500SX.
Tested by: Geans Pin < geanspin <> broadcom dot com >
support for their new RAID adapter ARC-1214.
Many thanks to Areca for continuing to support FreeBSD.
Submitted by: 黃清隆 Ching-Lung Huang <ching2048 areca com tw>
MFC after: 2 weeks
Starting with firmware v7.5, the "Read TouchPad Modes" ($01) and "Read
Capabilities" ($02) commands changed: previously constant bytes now
carry variable information.
We now compare those bytes to expected constants only for firmware prior
to v7.5.
Tested by: Zeus Panchenko <zeus@gnu.org.ua>
MFC after: 1 week
* The warning message was:
'warning error: format string is not a string literal';
* Changed how make_dev is called, now a string literal
for formatting is used;
Approved by: adrian (mentor)
LUNs for the virtual processor device. This removes lots of CAM warnings,
and follows similar recent changes to tws(4) and twa(4) drivers.
Also fix case where CAM_REQ_CMP was getting OR'd with CAM_DEV_NOT_THERE
in the nonexistent LUN case, resulting in different CAM status (CAM_UA_TERMIO)
getting reported to CAM. This issue existing previously, but was more subtle
because it changed CAM_SEL_TIMEOUT to CAM_CMD_TIMEOUT.
Sponsored by: Intel
Reported and tested by: Willem Jan Withagen <wjw@digiware.nl>
MFC after: 1 week
This fixes panic when listing sysctls on INVARIANTS-enabled kernel while
having wbwd loaded.
This panic was not fatal, at worst one additional space was printed.
Also sbuf_trim() makes some sense even if drain function is set. The drain
function is called only when buffer is to be expanded. So we could still trim
existing buffer before drain is called. In this case it worked just fine - the
trailing space was correctly trimmed.
Obtained from: WHEEL Systems
MFC after: 1 week
If virtio_setup_intr() failed during boot, we would hang in
taskqueue_free() -> taskqueue_terminate() for all the taskq
threads to terminate. This will never happen since the
scheduler is not running by this point.
Reported by: neel, grehan
Approved by: grehan (mentor)
I am not exactly sure about the naming due to lack of specs on AMD site,
but it is better to have some identification then none at all.
MFC after: 1 month
These must have been accidently copied from the if statement a few
lines later. Also remove parameter name from function prototype.
Approved by: grehan (mentor)
to map, and technically this isn't allowed.
Functionally, it works OK (at least on x86) to call bus_dmamap_load with
a NULL data pointer and zero length, so this is primarily for correctness
and consistency with other drivers.
While here, remove check in isci_io_request_construct for nseg==0.
Previously, bus_dmamap_load would pass nseg==1, even for case where
buffer is NULL and length = 0, which allowed CAM_DIR_NONE CCBs
to get processed. This check is not correct though, and needed to be
removed both for the changes elsewhere in this patch, as well as jeff's
preliminary bus_dmamap_load_ccb patch (which uncovered all of this in
the first place).
MFC after: 3 days
thought I've decided its overkill,a simple tuneable for
each RX and TX limit, and then init sets the ring values
based on that, should be sufficient.
More importantly, fix a bug causing a panic, when changing
the define style to IXGBE_LEGACY_TX a taskqueue init was
inadvertently set #ifdef when it should be #ifndef.
I couldn't think of a way to maintain the hardware TXQ locks _and_ layer
on top of that per-TXQ software queuing and any other kind of fine-grained
locks (eg per-TID, or per-node locks.)
So for now, to facilitate some further code refactoring and development
as part of the final push to get software queue ps-poll and u-apsd handling
into this driver, just do away with them entirely.
I may eventually bring them back at some point, when it looks slightly more
architectually cleaner to do so. But as it stands at the present, it's
not really buying us much:
* in order to properly serialise things and not get bitten by scheduling
and locking interactions with things higher up in the stack, we need to
wrap the whole TX path in a long held lock. Otherwise we can end up
being pre-empted during frame handling, resulting in some out of order
frame handling between sequence number allocation and encryption handling
(ie, the seqno and the CCMP IV get out of sequence);
* .. so whilst that's the case, holding the lock for that long means that
we're acquiring and releasing the TXQ lock _inside_ that context;
* And we also acquire it per-frame during frame completion, but we currently
can't hold the lock for the duration of the TX completion as we need
to call net80211 layer things with the locks _unheld_ to avoid LOR.
* .. the other places were grab that lock are reset/flush, which don't happen
often.
My eventual aim is to change the TX path so all rejected frame transmissions
and all frame completions result in any ieee80211_free_node() calls to occur
outside of the TX lock; then I can cut back on the amount of locking that
goes on here.
There may be some LORs that occur when ieee80211_free_node() is called when
the TX queue path fails; I'll begin to address these in follow-up commits.
This brand of controllers expects that the number of
contexts specified in the input slot context points
to an active endpoint context, else it refuses to
operate.
- Ring the correct doorbell when streams mode is used.
- Wrap one or two long lines.
Tested by: Markus Pfeiffer (DragonFlyBSD)
MFC after: 1 week
... to avoid any races or inconsistencies.
This should fix a regression introduced in r243404.
Also, remove a stale comment that has not been true for quite a while
now.
Pointyhat to: avg
Teested by: trociny, emaste, dumbbell (earlier version)
MFC after: 1 week
enforcing the TXOP and TBTT limits:
* Frames which will overlap with TBTT will not TX;
* Frames which will exceed TXOP will be filtered.
This is not enabled by default; it's intended to be enabled by the
TDMA code on 802.11n capable chipsets.
the revamped sysctl code did not work, and needed a change. This
makes the limit get set at the time that all sysctl stats are
created and is actually more elegant imho anyway.
TX hot path by getting rid of index calculations and simply
managing pointers. Much of the creative code is due to my
coworker here at Intel, Alex Duyck, thanks Alex!
Also, this whole series of patches was given the critical
eye of Gleb Smirnoff and is all the better for it, thanks
Gleb!
- add a limit for both RX and TX, change the default to 256
- change the sysctl usage to be common, and now to be called
during init for each ring.
- the TX limit is not yet used, but the changes in the last
patch in this series uses the value.
- the motivation behind these changes is to improve data
locality in the final code.
- rxeof interface changes since it now gets limit from the
ring struct
defines (at Gleb's request). Also, change the defines around
the old transmit code to IXGBE_LEGACY_TX, I do this to make
it possible to define this regardless of the OS level (it is
not defined by default). There are also a couple changed
comments for clarity.
these are FCOE stats (fiber channel over ethernet), something that
FreeBSD does not yet have, they were mistaken for flow control by
the implementor I believe. Secondly, the real flow control stats
are oddly named with a 'link' tag on the front, it was requested
by my validation engineer to make these stats have the same name as
the igb driver for clarity and that seemed reasonable to me.
multiqueue code, this functionality has proven to be more
trouble than it was worth. Thanks to Gleb for a second
critical look over my code and help in the patches!
It returns memory regions restricted from being used by kernel. These
regions are dfined in "memreserve" property of root node in the same
format as "reg" property of /memory node
embryonic connection has been setup and never attempt to abort a tid
before this is done. This fixes a bad race where a listening socket is
closed when the driver is in the middle of step (b) here. The symptom
of this were "ARP miss" errors from the driver followed by tid leaks.
A hardware-offloaded passive open works this way:
a) A SYN "hits" the TCAM entry for a server tid and the chip delivers it
to the queue associated with the server tid (say, queue A). It waits
for a response from the driver telling it what to do.
b) The driver decides it is ok to proceed. It adds the new tid to the
list of embryonic connections associated with the server tid and then
hands off the SYN to the kernel's syncache to make sure that the kernel
okays it too. If it does then the driver provides an L2 table entry,
queue id (say, queue B), etc. and instructs the chip to send the SYN/ACK
response.
c) The chip delivers a status to queue B depending on how the third step
of the 3-way handshake goes. The driver removes the tid from its list
of embryonic connections and either expands the syncache entry or
destroys the tid. In any case all subsequent messages for the new tid
will be delivered to queue B, not queue A. Anything running in queue B
knows that the L2 entry has long been setup and the new flag is of no
interest from here on. If the listener is closed it will deal with
so_comp as normal.
MFC after: 1 week
now this works for non-debug and debug builds.
* Add a comment reminding me (or someone) to audit all of the relevant
math to ensure there's no weird wrapping issues still lurking about.
But yes, this does seem to be mostly working.
Pointy-hat-to: adrian, yet again
* add some further debugging prints, which are quite nice to have
* add in ALQ hooks (optional!) to allow for the TDMA information to be
logged in-line with the TX and RX descriptor information.
The existing logic wrapped programming nexttbtt at 65535 TU.
This is not good enough for the 11n chips, whose nexttbtt register
(GENERIC_TIMER_0) has an initial value from 0..2^31-1 TSF.
So converting the TU to TSF had the counter wrap at (65535 << 10) TSF.
Once this wrap occured, the nexttbtt value was very very low, much
lower than the current TSF value. At this point, the nexttbtt timer
would constantly fire, leading to the TX queue being constantly gated
open.. and when this occured, the sender was not correctly transmitting
in its slot but just able to continuously transmit. The master would
then delay transmitting its beacon until after the air became free
(which I guess would be after the burst interval, before the next burst
interval would quickly follow) and that big delta in master beacon TX
would start causing big swings in the slot timing adjustment.
With this change, the nexttbtt value is allowed to go all the way up
to the maximum value permissable by the 32 bit representation.
I haven't yet tested it to that point; I really should. The AR5212
HAL now filters out values above 65535 TU for the beacon configuration
(and the relevant legal values for SWBA, DBA and NEXTATIM) and the
AR5416 HAL just dutifully programs in what it should.
With this, TDMA is now useful on the 802.11n chips.
Tested:
* AR5416, AR9280 TDMA slave
* AR5413 TDMA slave
what the maximum legal values are.
The current beacon timer configuration from TDMA wraps things at
HAL_BEACON_PERIOD-1 TU. For the 11a chips this is fine, but for
the 11n chips it's not enough resolution. Since the 11a chips have a
limit on what's "valid", just enforce this so when I do write larger
values in, they get suitably wrapped before programming.
Tested:
* AR5413, TDMA slave
Todo:
* Run it for a (lot) longer on a clear channel, ensure that no strange
slippages occur.
* Re-validate this on STA configurations, just to be sure.
fail or not. The mbuf pointer is no longer valid, so
can't be reused after.
Fix igb_mq_start() where mbuf pointer was used after
drbr_enqueue().
This eventually leads us to all invocations of
igb_mq_start_locked() called with third argument as NULL.
This allows us to simplify this function.
Submitted by: Karim Fodil-Lemelin <fodillemlinkarim gmail.com>
Reviewed by: jfv
detailed information under the sound debug. To make it easier accessible,
export that information through the set of sysctls like dev.hdaa.X.nidY.
Also tune some output to make it both more compact and informative.
After chatting with the MAC team, the TSF writes (at least on the 11n
MACs, I don't know about pre-11n MACs) are done as 64 bit writes that
can take some time. So, doing a 32 bit TSF write is definitely not
supported. Leave a comment here which explains that.
Whilst here, add a comment which outlines that after a reset or TSF
write, the TSF write may take a while (up to 50uS) to update.
A write or reset shouldn't be done whilst the previous one is in
flight. Also (and this isn't currently done) a read shouldn't
occur until the SLEEP32_TSF_WRITE_STAT is clear. Right now we're
not doing that, mostly because we haven't been doing lots of TSF
resets/writes until recently.
TSF write.
The TSF_L32 update is fine for the AR5413 (and later, I guess) 11abg NICs
however on the 11n NICs this didn't work. The TSF writes were causing
a much larger time to be skipped, leading to the timing to never
converge.
I've tested this 64 bit TSF read, adjust and write on both the
11n NICs and the AR5413 NIC I've been using for testing. It works
fine on each.
This patch allows the AR5416/AR9280 to be used as a TDMA member.
I don't yet know why the AR9280 is ~7uS accurate rather than ~3uS;
I'll look into it soon.
Tested:
* AR5413, TDMA slave (~ 3us accuracy)
* AR5416, TDMA slave (~ 3us accuracy)
* AR9280, TDMA slave (~ 7us accuracy)
on the 802.11n NICs.
The 802.11n NICs return a TBTT value that continues far past the 16 bit
HAL_BEACON_PERIOD time (in TU.) The code would constrain nextslot to
HAL_BEACON_PERIOD, but it wasn't constraining nexttbtt - the pre-11n
NICs would only return TU values from 0 -> HAL_BEACON_PERIOD. Thus,
when nexttbtt exceeded 64 milliseconds, it would not wrap (but nextslot
did) which lead to a huge tsfdelta.
So until the slot calculation is converted to work in TSF rather than
a mix of TSF and TU, "make" the nexttbtt values match the TU assumptions
for pre-11n NICs.
This fixes the crazy deltatsf calculations but it doesn't fix the
non-convergent tsfdelta issue. That'll be fixed in a subsequent commit.
... instead of the ever increasing ones.
Also, do free old resources when allocating new ones when cx states
change.
Tested by: Tom Lislegaard <Tom.Lislegaard@proact.no>
Obtained from: jkim
MFC after: 1 week
- The feature is dangerous because the kernel code didn't check
validity of the memory address provided from user space.
- It seems that mdconfig(8) never really supported attaching preloaded
memory disks.
- Preloaded memory disks are automatically attached during md(4)
initialization. Thus there shouldn't be much use for the feature.
PR: kern/169683
Discussed on: freebsd-hackers
encryption types.
The AR5210 only has four WEP key slots, in contrast to what the
later MACs have (ie, the keycache.) So there's no way to store a "clear"
key.
Even if the driver is taught to not allocate CLR key entries for
the AR5210, the hardware will actually attempt to decode the encrypted
frames with the (likely all 0!) WEP keys.
So for now, disable the hardware encryption entirely and just so it
all in software. That allows both WEP -and- WPA to actually work.
If someone wishes to try and make hardware WEP _but_ software WPA work,
they'll have to create a HAL capability to enable/disable hardware
encryption based on the current STA/Hostap mode. However, making
multi-vap work with one WEP and one WPA VAP will require hardware
encryption to be disabled anyway.
from HDMI/DisplayPort devices in form of general connection status and
sound(4)-style channel matrix. Now that information is only reported in
readable form to verbose logs, but potentially could be used by sound(4)
to correctly choose default devices and configure vchans.
Fix rear and side channels swap on analog 7.1 outputs. As soon as there is
a huge mess in industry about naming and using of these channels, duplicate
rear channels of 4 and 5.1 streams to both read and side speakers.
