OpenBSD who got the code (or the idea) from the NetBSD tlp driver.
This gets some cardbus dc cards working (either completely or nearly
so). It also appears to get additional pci cards working, without
breaking working ones.
# Maybe some additional work is needed here. Also, the cardbus attachment
# might need to match on the CIS rather than on the vendor/device so we have
# a finer level of detail as to what the card is. Technically, the
# vendor/device fields are undefined for CardBus (even though most cards are
# using common silicon with pci models).
According to the MII specification, the delay produced by our
reads alone are sufficient for correct operation.
This reduces the time mii_tick takes from 10ms to ~1ms here. That's
still a lot, but much better than before.
Submitted by: Harti Brandt <brandt@fokus.gmd.de>
MFC after: 3 weeks
RXSTATE to STOPPED, but to WAIT. This should fix hangs which
could only be solved by replugging the cable.
Submitted by: jhb
Reviewed by: phk
MFC after: 2 weeks
The 550 version is location at address 1 but since it works right we
let the code find whatever PHY it can.
Fix a fragment issue on TX. If the number of frags are more then the
driver has allocated then bring all the frags together into one packet
and send it out. Code derived from the fxp driver.
Tested and found by: Francois Tigeot <francois.tigeot@nic.fr>
Hellmuth Michaelis <hm@kts.org>
MFC after: 1 week
pmap_zero_page() and pmap_zero_page_area() were modified to accept
a struct vm_page * instead of a physical address, vm_page_zero_fill()
and vm_page_zero_fill_area() have served no purpose.
when this is needed. Work around bogus second PHY in the DFE-580 card
via a change in the if_ste.c driver.
Suggested by: jdp
Reviewed by: jdp
MFC after: 3 days
elimiates the driver lockup problem reported by many.
Concepts used were taken from Via's if_fet driver. Verification
and implementation were done by Thomas Nystrom.
Submitted by: Thomas Nystrom <thn@saeab.se>
MFC after: 3 days
This is pretty much fixes any issue I can find:
- Watchdog timeouts were due to starting the TX DMA engine
before we had a packet ready for it. So the first packet
sent never got out only if we sent more then one packet
at a time did the others make it out and not blow up.
Of course reseting the chip then caused us not to transmit
the first packet again ie. catch-22. This required logic changes.
- Combine interrupts on TX packets being queued up.
- Don't keep running around the RX ring since we might get
out of sync so only go around once per receive
- Let the RX engine recover via the poll interface which is
similar to the TX interface. This way the chip wakes
up with no effort when we read enough packets.
- Do better hand-shaking on RX & TX packets so they don't
start of to soon.
- Force a duplex setting when the link comes up after
an ste_init or it will default to half-duplex and be
really slow. This only happens on subsequent ste_init.
The first one worked.
- Don't call stat_update for every overflow. We only monitor
the collisions so the tick interval is good enough for that.
Just read in the collision stats to minimize bus reads.
- Don't read the miibus every tick since it uses delays and
delays are not good for performance.
- Tie link events directly to the miibus code so the port
gets set correctly if someone changes the port settings.
- Reduce the extreme number of {R,T}FD's. They would consume
130K of kernel memory for each NIC.
- Set the TX_THRESH to wait for the DMA engine to complete
before running the TX FIFO. This hurts peak TX performance
but under bi-directional load the DMA engine can't keep up
with the FIFO. Testing shows that we end up in the case
anyways (a la dc(4) issues but worse since the RX engine hogs
everything).
- When stopping the card do a reset since the reset verifies the
card has stopped. Otherwise on heavy RX load the RX DMA engine
is still stuffing packets into memory. If that happens after
we free the DMA area memory bits get scribled in memory and
bad things happen.
This card still has seemingly unfixable issues under heavy RX load in
which the card takes over the PCI bus.
Sponsored by: Vernier Networks
MFC after: 1 week
Remove some unnecessary assignments to mbuf fields in sis_newbuf(),
the "length" fields are of no use while the mbuf is in the receive ring.
MFC after: 3 days
sizes. Previously, the end result was at the mercy of the card's default
setting. This change will reduce the number of buffer underruns for
some users.
PR: kern/37929
Submitted by: Thomas Nystrom <thn@saeab.se>
MFC after: 7 days
