DEB macro). There are probably quite a few other messages that warrant
a similar treatment, and many more that should be converted to plain
log messages (e.g. "WARNING: wrintr but write DMA inactive!"). Now
that I think of it, same goes for the CAM code (e.g. the famed "tagged
openings" message)
though I'm afraid there's a lot more that needs fixing in this file,
judging by 'find /usr/src -name "*.8" -print'.
Spotted-by: glimpse -H /usr/src tickadj
Disable building tickadj(8) by removing util from SUBDIR in the xntpd
Makefile. Note that the sources are still there and tickadj can still
be built and installed by doing:
# cd /usr/src/usr.sbin/xntpd/util
# make all install
There are enough references to tickadj in e.g. the xntpd documentation
(not to mention the sysctl variables it uses etc.) that I don't feel
up to implementing the final solution right now.
Kinda-approved-by: phk
command on drives that don't like it. Right now, there's just a bogus
quirk entry in the table that doesn't do anything, but that should be
changed once we get actual inquiry data for drives that don't like the
synchronize cache command.
Also, add a shutdown hook that runs through all direct access peripherals
and runs a synchronize cache on them if they're still open, and if
synchronize cache isn't disabled via a quirk entry.
Add a synchronize cache call at the end of dadump() (again, conditionalized
on the quirk entry), so we can insure that the disk cache contents get
flushed to physical media after a dump.
Check the new quirk entry in daclose() to decide whether or not to
synchronize the cache for a disk at final close.
Reviewed by: gibbs
to convert the timeval into a tick count.
Suggested by: bde
Reviewed by: bde
Handle hz > 1000 in BIOCGRTIMEOUT.
Pointed out by: bde
Reviewed by: bde
Obtained from: OpenBSD
At some point, it will always be off from the user's POV and used
only internally to build (optionall) both mfskern floppies and
ones where mfs root and kernel go in separate places.
I'll convert sysinstall to use shortly) and a simple call which uses
this mechanism to implement an /etc/auth.conf file. I'll let Mark Murray
handle the format and checkin of the sample auth.conf file.
Reviewed by: markm
As a side effect, a few wakeup() calls are added, which might fix some of the
missing vm_page wakeups people have been seeing.
Reviewed by: Doug Rabson <dfr@nlsystems.com>
Disable DPARCKEN in the DSCOMMAND0 register on the aic7890/91/96/97.
Parity checking is broken for some chip/MB combinations and this
is the work around recommended by Adaptec.
dpt_pci.c:
Remove a superflous '{' that prevented DPT_ALLOW_MEMIO from working.
pcireg.h:
Add a definition for Parity Error Reponse bit in the PCI Space
command register.
Enable optimization for nobounce_dmamap clients by setting the map
held by the client to NULL. This allows the macros in bus.h to check
against a constant to avoid function calls.
Don't attempt to 'free()' contigmalloced pages in bus_dmamem_free().
We currently leak these pages, which is not ideal, but is better than
a panic. The leak will be fixed when contigmalloc is merged into the
bus dma framework after 3.0R.
queued.
Perform dma segment setup outside of splcam protection as this can take
some time and the protection is not necessary.
Inline a function.
Clean up some whitespace.
tagged queuing support.
Ensure that we report that a device supports tagged queuing even if
the system is waiting a "command count delay" before starting to use
them.
If a user disables disconnects on a device ensure that tagged queuing
is also turned off. We did the right thing during initial configuration,
but could be confused by manual changes.
